Sonar SCS-110M-03-EN User manual

SCS-1 0 -1 M-03 EN
Fire Protected Ceiling peaker/ Wall Louds
Features
- Steel re protect efi iv enclouser
-Surface / recessed mounting
- Stainless steel cable glands
- Ceramic s l blockcrew termina
- rotect e hermal fuseP iv t
Applications
- Indoor voice alarm systems
- Indoor background music
systems
SCS-1 01 M-03-EN is a re-protected ceilingfi /wall
loud use inspeaker, specifically designed for
buildings where the performance of Public Address
and Voice Alarm (PA/VA) systems is subject to
Dimensions
1
official regulations. It is compliant with BS 5839-8
and EN 60849 standarts.
The loudspeaker has built-in protection to ensure
that in the event of a fire damage does not cause
failure of connected circuit. In this way, system
integrity is maintained - ensuring loudspeakers in
other areas can still be used to inform people of
the situation.
The loudspeaker is with a 100 Vequipped
transformer with power ap for W for use int 10
large PA/VA systems.
191
170
85
83,5

Frequency Response
2
SCS-1 0 -1 M-03 EN
Technical Specifications
Power Handling 3 W
Rated Input 100 V
Transformer Tapping 3 W
SPL (1 / )W m
Max SPL (rated 1 m) 98 ± 3 dB
Frequency Response 190 9Hz –kHz
Dispersion 1 kHz / 4 kHz 1 08 °/ 56°
Dimensions ( x )W H x D 1 0 x mm7 191 x 67
Cutout Size (diameter) 16 mm6
Material
Weight (inc. packaging) 1. kg1
Colour
Steel
White RAL9003
91 ± 3 dB
Fire Protected Ceiling peaker/ Wall Louds

Wiring
Connect the lead-in cable (the one from the ampli er) to the screw terminal. In this casefi
strip wires on the picturethe cable as shown below.
Wiring Diagram
When connecting the lead-out cable (the one to the next speaker), connect both the
lead-in and leadout cables of the same polarity to each corresponding input terminal.
From the speaker
unit (pre-wired)
70 mm (2.76")
8 mm (0.31")
[Cable end treatment]
Screw terminal
COM
COM
HOT
HOT
Viewed from the screw terminal's bottom side
HOT
COM
To the next speaker
From the ampli erfi
From the ampli erfi
8Ω
10 W
0
COM
Earth
Screw terminal
HOT (+) HOT (red)
COM (black)
COM (–)
Matching
transformer
Thermal fuse
(96 C 204.8 F)º / º
3
SCS-1 0 -1 M-03 EN
Fire Protected Ceiling peaker/ Wall Louds

Installation Procedure
4
SCS-1 0 -1 M-03 EN
1) In case of cut a hole in a ceiling/wall in the desired mountingrecessed mounting
location of the loudspeaker.
2) Remove front part from the cabinet.
3) Screw cabinet to ceiling/wall with 2-4 screws.
4) Loosen the clamping screw-nut of one of two cable glands and put connecting cable
through the cable gland.
5) .Connect cable to the screw terminal and tighten the screw-nut of the cable gland
6) Screw front part to the cabinet with two provided screws.
Fire Protected Ceiling peaker/ Wall Louds
Certifications And Appruvals
All SONAR loudspeakers are designed to withstand operating at their rated power for
100 hours in accordance with IEC 268-5 Power Handling Capacity(ГОСТ 16122-87)
(PHC) standards. This ensures extra reliability under extreme conditions, leading to
greater customer satisfaction, longer operating life, and much less chance of failure or
performance deterioration.
Safty of a is in accordance with IEC 60065.ll SONAR loudspeakers
This loudspeaker is supplied with a 1 year warranty against defective materials and
workmanship since date of purchase.
SONAR reserves the right to alter specifications without notice