SONARAY SunBrite Solar User manual

SunBrite Solar Installation Guide
TECHNICAL PARAMETERS
ATTENTION
INSTALLATION CONSIDERATION
1. Do not install solar modules near power lines, trees, shaded areas, or any obstructive areas.
2. Regularly check for loose mounting connections to prevent any potential accidents. Re-tighten screws and bolts as needed.
3. When installing the solar panel, the face of the panel should be directed south at a 30 degree tilt for maximum charge potential.
4. Remove magnet on motion sensor housing for proper use.
INSTALLATION DIAGRAM
PRODUCT
PHOTO
MODEL
NUMBER SR-3030 SR-3048 SR-3080
POWER
CONSUMPTION 32.3W 48.4W 75.6W
LED
DIODES 60 60 60
OPERATING
VOLTAGE 12-24V DC standard,100-277V AC ~ 50/60Hz
HOUSING
MATERIAL Aluminum
OPERATING
TEMPERATURE -25°C ~ +45°C / -13°F ~ +113°F
IP
RATING 65
EPA
RATING 5.24 ft² 8.39 ft² 12.02 ft²
BUG
RATING B2-U1-G1 B2-U1-G1 B3-U1-G2
WEIGHT 14.99 23.80 42.11
REV: 21 0101 0000
TYPEDATE
PROJECT
NOTES
www.sonarayled.com
®
©2021 | SONARAY LED LIGHTING HEADQUARTERS | 34 LAKEVIEW COURT VERONA, VA 24482 USA | OFFICE 844.202.5606 | FAX [phone]
This manual instructs the important information of installation and operation. Be sure to strictly follow
the instructions before use. To ensure correct installation and operation of the product, carefully read
and understand all contents of this guide. Any mechanical or electrical modications to the product
will void warranty and may cause dangerous hazards. To avoid potential issues caused by high
temperature, be sure no objects are on the lens while the product is switched on. For proper operation,
a qualied electrician should perform the installation. Ensure the normal ambient temperature of the
installation location is between -25°C ~ +45°C. Ensure the voltage of the luminaire is capatable with the
onsite voltage before installation. Any luminaire with damaged power cord should not be installed.
GENERAL MAINTENANCE
The solar panel should not come in contact with any hard materials or damage may occur.
The solar panel, lens, and housing can be cleaned using a soft cloth without any corrosive material.
Regularly check the screws and mounting bracket and tighten or adjust if necessary.

SunBrite Solar Installation Guide
REMOTE CONTROLLER
REV: 21 0101 0000
TYPEDATE
PROJECT
NOTES
www.sonarayled.com
®
©2021 | SONARAY LED LIGHTING HEADQUARTERS | 34 LAKEVIEW COURT VERONA, VA 24482 USA | OFFICE 844.202.5606 | FAX [phone]
The battery in located in an easy access receptacle on the back of the
assembly. Remove the hardware and slide the old battery out. Make the
connections to the battery and re-attached the plastic cap.
Remote controller has six (6) settings to choose from. To program or re-
program the SunBrite Solar Assembly, simply point the remote controller
towards the sensor on the xture and press the appropriate button.
• DEMO: Light turns on for one (1) minute then turns o󰀨 for testing purposes.
• OFF: No matter the time of day or night, the light remains “OFF”.
• L: 12 hours 100% illuminance
• T: 4 hours 100% illuminance, 8 hours 30% illuminance
• M: 2 hours 100% illuminance with motion detected
30% illuminance without motion detected
2 hours 80% illuminance with motion detected
25% illuminance without motion detected
8 hours 70% illuminance with motion detected
20% illuminance without motion detected
• U: 4 hours 100% illuminance
8 hours 70% illuminance with motion detected
20% illuminance without motion detected
SITUATION POSSIBLE REASON POSSIBLE SOLUTION
LED
DOES NOT
LIGHT UP
Poor connection Check wiring connections
No power to the luminaire Recycle power or check power connection
Insu󰀩cient panel charge Allow su󰀩encient charge
LED
FLICKER
Poor power connection Check power connection
Input voltage uctation Conrm voltage
LIGHT TROUBLESHOOTING
SOLAR LIGHT CONTROLLER STATUS INDICATOR
INDICATOR LIGHT STATUS DESCRIPTION
YELLOW
(MOTION SENSOR)
On Motion Detected
O󰀨 Without Motion Detected
GREEN
(LED DIODES)
On LED is ON
O󰀨 LED is OFF
Flicker LED short-circuit
BLUE
(BATTERY)
On Battery su󰀩ciently charged
O󰀨 Battery charging
Flicker Battery undervoltage
RED
(SOLAR PANEL)
On Battery maximum charged
O󰀨 Solar panel without output
Flicker Solar panel is charging battery
CONTROLLER TROUBLESHOOTING
BATTERY REPLACEMENT
STRUCTURE SPECIFICATION
1. Solar Panel
2. Adjustable Panel Bracket
3. Lithium Battery
4. Controller + Motion Sensor
5. LED Diodes
6. Lens
7. Battery Compartment