Sonelco PCB1350 User manual

Warningtransmittermodulefor5differentareasandgeneralcalls.Normally
usedincombinationwiththePCP1251orPCB1210warningreceivercontrol
devices, with two objectives: 1- Central warning transmitter.
2- Radial or ring intercommunication (see diagrammes).
Can also be used as an independent warning transmitter centre, but in this
case without any background music or warning reception in said centre.
(see attached diagramme)
Whenconnectedtoawarningreceivercontroldevice,acallshouldbemade
to this area to check that that the warning is heard correctly.
During the reception of the warning, the warning reception indicator (6)
Should light up.
To send a warning just push down on any of the area buttons
(1,2,3,4 or 5) or the general call button (5) and speak at a distance of
between 30 to 40 cm. from the microphone (7).
Themicrophonelevel(9)hasalreadybeenfactoryadjustedtothisdistance,
but this can be modified by the user to adjust the same to their particular
requirements. Warnings can only be transmitted when the Line Engaged
LED (6) is off
WARNING: The system cabling should be installed separately from
the mains electricity supply in accordance with regulations.
Supply voltage 16 V DC
Maximum consumption (transmitting calls) : 50 mA
Microphone: Unidirectional directivity
Frequency response: 90 Hz - 16 KHz.
Audio output level (Terminal 7): 3V
Nominal input level for warning switching: 15V
Nominal output level for calls (general and areas): 15V
Dimensions (L x H x D): 45x45x27 mm.
Weight: 50 grammes
Keypad for calls to 5 different areas.
Separate button for a general call to the entire installation.
Line Engaged indicating light.
High sensitivity microphone incorporated with output level adjustment
Before connecting the device, ensure that it is not connected to the mains
supply.Insertthecontrolinthemetalchassisandconnectupinaccordance
with the following instructions:
TERMINALS
2
3/9S
4
7
Z1
Z2
Z3
Z4
Z5
8
9R
9E
WARNING TRANSMITTER MODULE - PCB1350
GENERAL CALL MORE THAN 5 INDEPENDENT AREAS
4FA035001
DESCRIPTION
-
-
-
-
GENERAL CHARACTERISTICS
CONNECTION
Input +16V Supply
Transmission/reception of warning control output. For connection
to the 9R terminal of the attached control device (when connected
to a warning reception control device)
Earth
Audio warning Input/Output
Call to Area 1 output (connect toArea 1 wire)
Call to Area 2 output (connect toArea 2 wire)
Call to Area 3 output (connect toArea 3 wire)
Call to Area 4 output (connect toArea 4 wire)
Call to Area 5 output (connect toArea 5 wire)
Area select input. Connect to assigned area wire Zx (when con-
nected to a warning reception control device)
Generalcall input.Connect towire 9(when connected toa warning
reception control device
General call output. Connect to wire 9 to transmit a general call or
with wire Z0 for star intercommunication.
OPERATION
TECHNICAL CHARACTERISTICS
1 – Call to Area 1 button. 2 - Call to Area 2 button. 3
- Call to Area 3 button. 4 - Call to Area 4 button. 5
– General call button. 6 – Line Engaged indicating light. 7
- Microphone. 8 - Call to Area 5 button. 9 – Microphone
adjustment level..

These characteristics are for information purposes only. The manufacturer reserves the right to make modifications without prior notice in order to improve the product. PCB1350 26-03-07
INSTALLATION EXAMPLES
AREA 1
STEREO ROOM Transmission of
warnings to areas
Area and general warning reception
ASSEMBLY RECOMMENDATIONS: All the “COMPACT” series modules can be placed over the various types of embedded
boxes, for which we have various types of front frames that are delivered separately.
THE BASIC COMPACT SERIES CONTROL DEVICES CAN BE ASSEMBLED WITH ALL THE PRESTIGE LINE RANGE OF FRONT
FRAMES, WITH THE EXCEPTION OF MODELS KC9300 AND KC9302.
For further details please see www.sonelco.com
Connect terminal 8 with the
corresponding area wire in
each room
Any model of control
device or source of
supply
AREA 2
Only warning transmission
to areas
CENTRALISATION
Por GERARDO fecha 8:20 , 29/03/2007