Sonic Alert HomeAware HA360MK User manual

Complete Home Alerng Soluon
HA360MK
Quick Reference and Installaon Guide
Seng Up Your HomeAware™
1. Remove all contents of the box.
– HomeAware™ - Main Unit
– Doorbell Transmier
– Doorbell Chime Box Connector Cord
– Vibrator / Bed Shaker
– Telephone Line Cord
2. Plug the power supply into back of
the Main unit, 7.5V 2A DC IN.
3. Plug Main unit power supply into a
120V outlet.
4. Plug Vibrator/Bed Shaker into the
vibrator outlet on the back of the
Main unit. (Oponal)
Seng Time of Day
1. Press the Time Set buon. Blinking red
dots will show on the display.
2. Press the Hour and Minutes buons up
or down to set desired me. When
seng the me make sure the PM
indicator light reflects the correct me.
3. Press the Enter buon to complete.
Seng Alarm 1
1. Press and hold AL.1 Set buon. Blinking
red dots will show on the display.
2. Press the Hour and Minute buons up
or down to set desired alarm me.
3. Press the Enter buon when done to
complete. A red LED Alarm indicator
light will appear on the display’s le side
indicang alarm 1 is now set.
4. Repeat for AL.2.
1
2
3
PM Indicator
SNOOZE
AL.2 Set Hour Minute Back
Enter
Tone
Volume
AL.1 Set
Time Set Alarm Off Set Up
Main
PM
A1
A2
Alarm Indicator
SNOOZE
AL.2 Set Hour Minute Back
Enter
Tone
Volume
AL.1 Set
Time Set Alarm Off Set Up
Main
PM
A1
A2
7.5V 2A
DC IN
120V Outlet
7.5V 2A
DC IN
LAMP
SW.
EXT.
BATT.
USB CHARGE 5V
TEL.
TEL.
LINE CELL PHONE
DETECTOR
VIBRATOR
VIBRATOR/
BED SHAKER

LATCH TO OPEN
COMPARTMENT
DOOR
Seng Up Your Doorbell Transmier
1. Install provided baeries into the boom of
the unit.
2. Once installed push the link buon and the red
LED light will light. If the light does not show,
you may have the baeries in backwards.
4
Linking Doorbell Transmier to Main Unit
Do the LINK procedure in the same room as the
Main Unit.
1. Press Set Up and LINK will be shown, press Enter
the word LINK will begin blinking.
2. Press link buon on the boom of the doorbell
transmier. The red LED light on front of the
doorbell transmier will blink two mes and
DOOR will be shown, press Enter.
5
BATTERIES
LINK BUTTON
BATTERY/LINK
COMPARTMENT
DOOR
Complete Home Alerng Soluon
HA360MK
Quick Reference and Installaon Guide
Installing a Telephone Line to the Main Unit
1. Place the Main unit close to a standard RJ11
telephone wall jack.
2. Plug the phone line cord into the wall jack.
3. Plug the opposite end of the phone line
cord into the back of the Main unit,
TEL LINE.
4. To hookup a standard telephone plug the
phone jack into the back of the Main unit,
TEL.
5. To charge your smartphone, plug into the
USB CHARGE 5V.
7
7.5V 2A
DC IN
LAMP
SW.
EXT.
BATT.
USB CHARGE 5V
TEL.
TEL.
LINE CELL PHONE
DETECTOR
VIBRATOR
Installaon and Set Up of Doorbell Transmier
There are two methods to install and set up.
1. Stand-alone no exisng chime box. See page 26 of
User Guide.
2. To exisng chime box. See page 29 of User Guide.
6
EXISTING CHIME BOX
METHOD
LINK BUTTON
RJ11
WALL
JACK
SMARTPHONE
USB
CHARGER