Sonodyne SWH 056 User manual
SWH 056
wireless active noise cancelling headphone •owners manual
• safety warning • in the box •
SWH 056 SWH 056
Thank you for purchasing the Sonodyne SWH 056
wireless Active Noise Cancellation headphone.
Please read the user manual carefully before using
the product.
SAFETY WARNING
1. Please read the user manual carefully and
follow the instructions.
2. Please do not modify, assemble, disassemble,
or alter this headphone in any way. Misuse
may adversely affect performance and
functionality and also void your warranty.
3. To clean use a soft, moist cloth.
4. Listening at loud levels may permanently
damage your hearing, so please listen at
comfortable levels.
5. The ANC is very effective to drown ambient
noise, so please use it responsibly, especially
in areas where you need to be aware of your
surroundings.
IN THE BOX
1. Wireless Headphone
2. 1 x Micro USB Cable
3. 1 x 3.5mm Audio Cable
4. User manual
• button function •
1. Volume +
2. Volume –
3. Power/Play/Call
4. Pairing LED (Red/ Blue)
5. AUX-IN
6. Charging LED
7. ANC LED (Blue)
8. ANC ON/OFF
9. Micro USB
91 2 3 4 5 6 7 8
SWH 056
• charging •
SWH 056
CHARGING
Use the Micro USB cable to connect the 056 to a
charging outlet or your PC.
The red LED light is always on during charging. The
red light is off when fully charged. It usually takes
approximately 2 hours to attain full charge.
LOW BATTERY ALARM
When the battery power is less than 10% (and
the voltage is lower than 3.3V) the headphone
emits a beeping prompt tone, and the red light will
blink. When the battery voltage is lower than 3.1V,
wireless functionality turns off automatically.
PLEASE NOTE
1. Please do charge the headphone regularly
2. The headphone turns off automatically when
charging
• pairing •
1. Press and hold the button for about 5
seconds to enter pairing mode
2. Please select “SWH 056” to pair with your
device
3. Enter “0000” for pairing connection if PIN
code requested
4. There is a “CONNECTED” voice prompt when
pairing is successful
NOTE
• The headphone will enter into standby mode
after 10 minutes if no device is paired
• Use the 3.5 mm ep cable for wired operation
• Wireless function will be disabled in wired
mode.
• instructions •
• instructions •
SWH 056 SWH 056
SWITCH CONTROL
FUNCTION OPERATION PROMPT
POWER ON
Press and hold
the button
for about 3
seconds when
the headphone is
powered off
“POWER ON”
voice prompt, blue
LED light flashes
POWER OFF
Press and hold
the key for
about 3 seconds
when the
headphone is
powered on
“POWER OFF”
voice prompt,
red LED light
turns off
PAIRING
Press and hold
the key for
about 5 seconds
when the
headphone is
powered off.
The red and blue
LEDS light will
flash alternately
and there will be
a “CONNECTED”
voice prompt
when pairing is
successful
MEDIA PLAYER CONTROL
STATUS OPERATION PROMPT
PLAY
With music
paused, a short
press on
button
Blue LED light
flashes once in
5 seconds
PAUSE
With music
playing, a short
press on
button
Blue LED light
flashes once in
5 seconds
PREVIOUS
TRACK
Long press -
button for 2S for
previous track
Blue LED light
flashes twice in
5 seconds
NEXT TRACK
Long press +
button for 2S for
next track
Blue LED light
flashes twice in
5 seconds
TURN ON SIRI
OR GOOGLE
Long press
button for 1.5s
CLEAN PAIRED
DEVICE LIST
Press and hold
both and
- buttons for 5s
when power is on
but not paired
The red and
blue LED flash
alternately
twice
SWH 056 SWH 056
NOISE REDUCTION CONTROL
FUNCTION OPERATION PROMPT
TURN ON
ANC
Long press ANC
button around
1.5S when power
on or line in
Blue LED is on
TURN OFF
ANC
Long press ANC
button around
1.5S when ANC
function on
Blue LED light
is off
PHONE CALL CONTROL
FUNCTION OPERATION PROMPT
ANSWER
INCOMING
CALL
Short press
to answer a call
when there is a
call incoming
There will be a voice
prompt or ring
END A CALL
Short press
while the call is
in progress
End of the call
"beep" tone, red
LED light flashes
twice in 1s
VOLUME CONTROL
FUNCTION OPERATION PROMPT
VOLUME +
Short press
the + button
to increase the
volume
Blue LED light
is on. There is a
“beep” prompt tone
when the volume is
maximum
VOLUME -
Short press
the - button to
decrease the
volume
Blue LED light
is on. There is a
“beep” prompt tone
when the volume is
minimum
• instructions •
• instructions •
• specifications •
SWH 056 SWH 056
NO POWER Please check if low capacity of
battery and charging.
NO SOUND
WHEN
CONNECTED
TO A
EXTERNAL
DEVICE
WIRELESSLY
Check the volume and play/ pause
button status on the external device
and headphone to make sure
the wireless connection is set up
correctly.
Before connecting the headphone,
test the playback of the file on your
device to make sure this file is OK.
Make sure no other devices are
paired to either your playing device or
the headphone.
NO SOUND
WHEN
CONNECTED
TO A
EXTERNAL
DEVICE BY
3.5MM AUDIO
CABLE
Check the volume level of
the connected device and the
headphone, check the play/pause
button on the connected device,
and the line connecting the device
and the headphone is securely
connected.
Play the file on the test device before
connecting the headphone.
Try to play another file, maybe your
playing file is not compatible or
damaged.
Try using another cable; since these
cables are prone to damage over a
period of time Due to continuous improvements, all specifications are subject to change
DESCRIPTION Wireless headphone with
Ambient Noise Cancellation
DRIVER TYPE Dynamic
DRVER SIZE 40mm
FREQ. RESPONSE
(SPEAKER. 10dB) 20Hz ~ 22kHz
FREQ. RESPONSE
(MIC, -10dB) 70Hz ~ 8kHz
SPL (1kHz) 108dB
THD (1kHz) <0.5%
WIRELESS
CONNECTIVITY BT V 5.0
CONTROLS A2DP v1.3.1, AVRCP v1.6,
HFP v1.7
BATTERY LIFE 20 hours (BT mode)
16 hours (BT + ANC mode)
CHARGING TIME 2 hours
AUDIO CODEC SBC, AAC
WEARING STYLE Over ear
WEIGHT 245g
IN THE BOX User manual, 1 x USB cable,
1 x line-in cable
• troubleshooting •
SONODYNE, India •H.O.: 98 NB Block E New Alipore,
Kolkata 700053, INDIA
sonodyneofficial
SonodyneMusic
sonodyneofficial
+91 9830855260
www.sonodyne.com
Table of contents
