Sony CCD-TRV138 - Handycam Camcorder - 320 KP User manual

SECTION 6
ADJUSTMENTS
CCD-TRV138/TRV238E/TRV338/TRV438E
RMT-833
ADJ
Revision History
Revision History
Ver 1.0 2004. 11
Link
Link
Adjusting Items when Replacing Main Parts and Boards
Before Starting Adjustments
Adjusting Items when Replacing Main Parts and Boards
Before Starting Adjustments
LCD SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
CAMERA SECTION ADJUSTMENTS
INITIALIZATION OF 8, A, C, D, E, F, 1F PAGE DATA
LCD SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
INITIALIZATION OF 8, A, C, D, E, F, 1F PAGE DATA
PREPARATIONS BEFORE ADJUSTMENTS
CAMERA SECTION ADJUSTMENTS
TAPE PATH ADJUSTMENT
OPERATING WITHOUT CASSETTE
ADJUSTMENT REMOTE COMMANDER
MECHANISM SECTION ADJUSTMENTS
TAPE PATH ADJUSTMENT
OPERATING WITHOUT CASSETTE
ADJUSTMENT REMOTE COMMANDER
MECHANISM SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
Sony EMCS Co. 2004K0500-1
© 2004.11
Published by DITechnical Support Section
9-876-779-51
CCD-TRV138/TRV238E/TRV338/TRV438E

— 2 —
CCD-TRV138/TRV238E/TRV338/TRV438E
TABLE OF CONTENTS
6. ADJUSTMENTS
1. Before Starting Adjustments ···········································6-1
1-1. Adjusting Items when Replacing
Main Parts and Boards ····················································6-2
6-1. Camera Section Adjustments···········································6-4
1-1. Preparations before Adjustments (Camera Section)········6-4
1-1-1.List of Service Tools ························································6-4
1-1-2.Preparations ·····································································6-5
1-1-3.Precaution ········································································6-6
1. Setting the Switch····························································6-6
2. Order of Adjustments ······················································6-6
3. Subjects ···········································································6-6
1-2. Initialization of 8, A, C, D, E, F, 1F Page Data ···············6-7
1. Initializing the 8, A, C, D, E, F, 1F Page Data ················6-7
2. Modification of 8,A, C, D, E, F, 1F Page Data···············6-7
3. 8 Page Table·····································································6-7
4. A Page Table····································································6-8
5. C Page Table ····································································6-8
6. D Page Table····································································6-9
7. E Page Table ····································································6-9
8. F Page Table ··································································6-10
9. 1F Page Table ································································6-10
1-3. Camera System Adjustments ·········································6-11
1. HALL Adjustment ·························································6-11
2. Flange Back Adjustment
(Using the minipattern box or
flange back adjustment jig) ···········································6-12
3. Flange Back Adjustment
(Using the flange back adjustment chart
and subject more than 500 m away) ······························6-13
4. Flange Back Check························································6-14
5. Optical Axis Adjustment ···············································6-15
6. Picture Frame Setting ····················································6-16
7. Color Reproduction Adjustment····································6-17
8. LV Standard Data Input ·················································6-18
9. Auto White Balance Standard Data Input ·····················6-18
10. Auto White Balance Adjustment ···································6-19
11. Auto White Balance Check ···········································6-20
12. Angular Velocity Sensor Output Check and Steadyshot
Check (CCD-TRV338/TRV438E)·································6-21
13. CCD Defect Check ························································6-21
1-4. LCD System Adjustments ·············································6-22
1. LCD Level Adjustment (PD-204 Board)·······················6-22
2. LCD V-COMAdjustment (PD-204 Board) ···················6-23
3. LCD White Balance Adjustment (PD-204 Board) ········6-23
6-2. Mechanism Section Adjustments ··································6-24
2-1. Adjustment Remote Commander ··································6-24
2-2. Operating Without Cassette ···········································6-24
2-3. Tape Path Adjustment ····················································6-24
6-3. Video Section Adjustments ···········································6-25
3-1. Preparations before Adjustments ···································6-25
3-1-1.Equipment to Required··················································6-25
3-1-2.Precautions on Adjusting···············································6-26
3-1-3.Adjusting Connectors ····················································6-26
3-1-4.Connecting the Equipment ············································6-26
3-1-5.Alignment Tapes····························································6-27
3-1-6.Output Level and Impedance·········································6-28
3-1-7.Recording Mode (Standard 8/Hi8) Switching···············6-28
3-2. System Control System Adjustments ····························6-29
1. Initialization of 8, A, C, D, E, F, 1F Page Data ·············6-29
3-3. Servo System Adjustments ············································6-29
1. CAP FG Offset Adjustment (VC-341 Board) ···············6-29
2. Switching Position Adjustment (VC-341 Board) ··········6-29
3-4. Video System Adjustments············································6-30
Section Title Page Section Title Page
1. 28 MHz Origin Oscillation Adjustment
(VC-341 Board)·····························································6-30
2. AFC f0Adjustment (VC-341 Board) ·····························6-30
3. LINE OUT Level Adjustment (VC-341 Board) ············6-31
4. RECY Current Adjustment (VC-341 Board)················6-32
5. REC C/AFM Current Adjustment ·································6-33
5-1. Preparations ···································································6-33
5-2. REC C Current Check (VC-341 Board)························6-33
5-3. REC AFM Current Adjustment (VC-341 Board)··········6-34
5-4. Processing after Completed Adjustment ·······················6-34
3-5. Audio System Adjustments ···········································6-35
1. BPF f0Adjustment (VC-341 Board)······························6-35
2. 1.5 MHz Deviation Adjustment (VC-341 Board) ·········6-35
6-4. Service Mode·································································6-36
4-1. Adjustment Remote Commander ··································6-36
1. Using the Adjustment Remote Commander ··················6-36
2. Precautions Upon Using the Adjustment
Remote Commander······················································6-36
4-2. Data Process ··································································6-37
4-3. Service Mode·································································6-38
1. Setting the Test Mode ····················································6-38
2. Emergency Memory Address ········································6-39
2-1. EMG Code (Emergency Code) ·····································6-39
2-2. MSW Codes ··································································6-40
3. Bit Value Discrimination ···············································6-41
4. Switch Check (1) ···························································6-41
5. Switch Check (2) ···························································6-41
6. Switch Check (3) ···························································6-42
7. LED, Video Light, IR Light Check ·······························6-42
8. Record of Use Check·····················································6-43
9. Record of Self-diagnosis Check ····································6-44
*The camera optical axis frame is shown on page 6-45.
The camera color reproduction frame is shown on page
6-46.

6-1
CCD-TRV138/TRV238E/TRV338/TRV438E
SECTION 6
ADJUSTMENTS
1. Before Starting Adjustments
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a
board is replaced.
Remove the EEPROM and install it.
(Former board) (New board)
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed
EEPROM to the replaced board.
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.
After the EVR data is saved and downloaded, check the
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked)
(Machine before starting repair) (Machine after a board is replaced) PC PC
Save the EVR data
to a personal computer. Download the saved
data to a machine.
(Machine to be repaired) (Machine to be repaired)
(The same model of the same destination)
Save the data.
Download the data.
PC

6-2
CCD-TRV138/TRV238E/TRV338/TRV438E
1-1. Adjusting Items when Replacing Main Parts and Boards
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by zin the following table.
Table 6-1-1 (1)
Note 1: When replacing the drum assy or mechanism deck, reset the data of page: 7, address: A4 to A6.
(Refer to “Record of Use Check” of “6-4. SERVICE MODE”)
Note 2: When replacing the video light, reset the data of page: 7, address: CE and CF.
(Refer to “Record of Use Check” of “6-4. SERVICE MODE”)
Note 3: CCD-TRV338/TRV438E only
Replaced part
Block replacement Mounted part replacement
Adjustment Section Adjustment
(LCD panel) (Fluorescent tube) (Drum assembly) (Note 1) (Capstan motor) (CCD imager) (YAW, PITCH sensor) (Note 3) (Timing generator) (S/H, AGC, A/D CONV.) (Camera/VTR process, Lens control) (REC/PB AMP) (EVR) (Audio/Video process) (LCD driver)
Lens device Video light (Note 2) LCD block LCD901 LCD block ND901 Mechanism deck (Note 1) Mechanism deck M901 Mechanism deck M902 CD-465 board IC951 SI-039 board SE751/752 VC-341 board IC151, X151 VC-341 board IC152 VC-341 board IC301 VC-341 board IC481 VC-341 board IC251 VC-341 board IC801 PD-204 board IC6001
Initialization of 8, A, C, D,
E, F, 1F page data Initializing of 8, A, C, D, E, F, 1F page
data
Camera HALL adj. z
Flange back adj. zz
Optical axis adj. zz
Color reproduction adj. zz
LV standard data input zz
AWB standard data input zz
Auto white balance adj. zz
Angular velocity sensor output check
and steadyshot check (Note 3) z
LCD LCD level adj. z
LCD V-COM adj. zz
LCD White balance adj. zz z
Servo CAP FG offset adj. zz
Switching position adj. zz
Video 28 MHz origin osillation adj. zz
AFC f
0 adj. z
LINE OUT level adj. zz
REC Y current adj. zz
REC C/AFM current adj. zz
Audio BPF f
0 adj. z
1.5 MHz deviation adj. z
Mechanism Tape path adj. zzz

6-3
CCD-TRV138/TRV238E/TRV338/TRV438E
• Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by zin the following table.
Table 6-1-1 (2)
Replaced part
Adjustment Section Adjustment
(COMPLETE) (COMPLETE) (EEPROM)
PD-204 board VC-341 board VC-341 board IC602 Supporting
Initialization of 8, A, C, D,
E, F, 1F page data Initializing of 8, A, C, D, E, F, 1F page
data zz
Camera HALL adj. zzz
Flange back adj. zzz
Optical axis adj. zz
Color reproduction adj. zz
LV standard data input zzz
AWB standard data input zzz
Auto white balance adj. zzz
Angular velocity sensor output check
and steadyshot check (Note 3) zzz
LCD LCD level adj. zzzz
LCD V-COM adj. zzz
LCD White balance adj. zzz
Servo CAP FG offset adj. zzz
Switching position adj. zz
Video 28 MHz origin osillation adj. zz
AFC f
0 adj. zzz
LINE OUT level adj. zz
REC Y current adj. zz
REC C/AFM current adj. zz
Audio BPF f
0 adj. zz
1.5 MHz deviation adj. zz
Mechanism Tape path adj.
RadarWRadarWRadarW

6-4
CCD-TRV138/TRV238E/TRV338/TRV438E
Fig. 6-1-1
6-1. CAMERA SECTION ADJUSTMENTS
1-1. PREPARATIONS BEFORE ADJUSTMENTS (CAMERA SECTION)
1-1-1. List of ServiceTools
• Oscilloscope • Color monitor • Vectorscope
• AC power adapter • Frequency counter
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-2 Color bar chart
For PTB-450:
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-3
Clear chart
For PTB-450:
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-4 J-5
Minipattern box
J-6082-353-B
J-7
Siemens star chart
J-6080-875-A
J-8
Filter for color
temperature correction
(C14)
J-6080-058-A
J-9 ND filter 1.0
J-6080-808-A
ND filter 0.4
J-6080-806-A
ND filter 0.1
J-6080-807-A
J-6
Flange back
adjustment jig
J-6082-563-A
J-10
Back ground paper
J-2501-130-A
J-11
Camera table
J-6082-384-A
J-1
Adjustment remote
commander
J-6082-053-B
CPC jig connector
J-6082-539-A
J-12
I/F unit for LANC control
J-6082-521-A
J-13

6-5
CCD-TRV138/TRV238E/TRV338/TRV438E
CN007
A/V OUT jack
16
1
Audio (black)
Video (yellow)
TV monitor
AC adaptor AC IN
AC adaptor
CPC lid
Screw (M2)
I/F unit for LANC control
(J-6082-521-A)
CPC jig connector
(J-6082-539-A)
L serices Info
LITHIUM battery (7.2Vdc)
Adjustment
remote commander (RM-95)
Conductor side
LANC jack
AC IN
Terminated at 75Ω
Vector scope
Fig. 6-1-2
1-1-2. Preparations
Note: Before perform the adjustment, check that the data of page:
0, address: 10 is “00”.
If not, select page: 0, address: 10, and set data “00”.
1) Connect the equipment for adjustments according to Fig. 6-1-
3.
2) Connect the adjustment remote commander to VC-341 board
CN007 via I/F unit for LANC control (J-6082-521-A) and CPC
jig connector (J-6082-539-A). (Fig. 6-1-3)
To operate the adjustment remote commander, connect theAC
power adaptor to the DC IN jack of I/F unit for LANC control,
or connect the L series Info-LITHIUM battery to the battery
terminal of I/F unit for LANC control.
Fig. 6-1-3
Front of the lens
L = 1m (PTB-450)
L = 40cm (PTB-1450)
L
Pattern box

6-6
CCD-TRV138/TRV238E/TRV338/TRV438E
H
A=B
C=D
AB B
CD
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
BA
Difference in level
Yellow
Cyan
Green
White
Magenta
Red
Blue
Yellow
Cyan
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame)
Fig. a
(VIDEO terminal of A/V jack
output waveform)
Fig. b (monitor TV picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig.a and
the monitor TV display shown in Fig.b.
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1. POWER switch (SS-5100 block) ..........................CAMERA
2. FOCUS (CF-5100 block) ..................................... MANUAL
3. BACK LIGHT (CF-5100 block) .................................... OFF
4. PROGRAM AE (MENU setting) ................................ AUTO
5. NIGHTSHOT PLUS switch (Lens block) ..................... OFF
6. EXPOSURE (CF-5100 block) .................................... AUTO
7. P EFFECT (MENU setting) ........................................... OFF
8. D ZOOM (MENU setting) ............................................. OFF
9. DEMO MODE (MENU setting) .................................... OFF
10. 16 : 9 WIDE (MENU setting) ........................................ OFF
11. DISPLAY (MENU setting) ............................................ LCD
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig. 6-1-4
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2) Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clearchartin its place. (Donot perform zoom operationsduring
this time)
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189mm ×841
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-5.
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.
Fig. 6-1-5
Black
White 841 mm
1189 mm

6-7
CCD-TRV138/TRV238E/TRV338/TRV438E
1-2. INITIALIZATION OF 8, A, C, D, E, F, 1F
PAGE DATA
Note: If reading/writing data on pages 1F, set data: 01 to page: 0,
address: 10, and then select pages F. By this data setting,
the pages 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
1. Initializing the 8, A, C, D, E, F, 1F Page Data
Note 1: If “Initialization of Pages 8, A, C, D, E, F, 1F” is ex-
ecuted, all data on pages 8, A, C, D, E, F, 1F are initial-
ized. (Only an individual page cannot be initialized)
Note 2: If the 8, A, C, D, E, F, 1F page data has been initialized,
“Modification of 8,A, C, D, E, F, 1F Page Data” and all
adjustments need to be performed again.
Note 3: Check that the data of page: 0, address: 10 is “00”.
Note 4: NTSC model: CCD-TRV138/TRV338
PAL model: CCD-TRV238E/TRV438E
Adjusting Page 8
Adjusting Address 00 to FF
Adjusting Page A
Adjusting Address 10 to FF
Adjusting Page C
Adjusting Address 10 to FF
Adjusting Page D
Adjusting Address 10 to 7F
Adjusting Page E
Adjusting Address 00 to FF
Adjusting Page F
Adjusting Address 10 to FF
Adjusting Page 1F
Adjusting Address 00 to FF
Initializing method:
Order Page Address Data Procedure
10 0101
27 03 Set the following data.
00: NTSC model
80: PAL model
37 00 Set the following data. 2D: NTSC model
2F: PAL model
47 01
Set the following data, and
press PAUSE button.
2D: NTSC model
2F: PAL model
57 02 Check the data changes to
“01”.
62 0029
72 01 29 Press PAUSE button.
8Perform “Modification of 8,
A, C, D, E, F, 1F Page Data”
2. Modification of 8, A, C, D, E, F, 1F Page Data
If the 8, A, C, D, E, F, 1F page data has been initialized, change
the data of the “Fixed data-2” address shown in the following table
by manual input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
3) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after completing modification of 8,A, C, D, E, F, 1F
page data
Order Page Address Data Procedure
12 0029
22 01 29 Press PAUSE button.
Note: If the following symptoms occur after completing of the
“Modification of 8, A, C, D, E, F, 1F Page Data”, check
that the data of the “Fixed data-2” addresses of 8,A, C, D,
E, F, 1F page are same as those of the same model of the
same destination.
1) The power is shut off so that unit cannot operate.
3. 8 PageTable
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address Initial value Remark
NTSC PAL
00 to FF Fixed data-1 (Initialized data)

6-8
CCD-TRV138/TRV238E/TRV338/TRV438E
4. A PageTable
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address Initial value Remark
NTSC PAL
10 to 20 Fixed data-1 (Initialized data)
21 Fixed data-2
22 to 2B Fixed data-1 (Initialized data)
2C Fixed data-2
2D to 30 Fixed data-1 (Initialized data)
31 Fixed data-2
32 to 40 Fixed data-1 (Initialized data)
41 Fixed data-2
42 to 44 Fixed data-1 (Initialized data)
45 Fixed data-2
46 to 4B Fixed data-1 (Initialized data)
4C Fixed data-2
4D to 9C Fixed data-1 (Initialized data)
9D
9E
9F Fixed data-2
A0 to FF Fixed data-1 (Initialized data)
5. C PageTable
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address Initial value Remark
NTSC PAL
10 to 13 Fixed data-1 (Initialized data)
14 00 00 Test mode
15 Fixed data-1 (Initialized data)
16 0B 0A Switching position adj.
17 00 00
18 83 83 CAP FG offset adj.
19 30 30 AFC f0adj.
1A 68 62 LINE OUT level adj.
1B 62 62
1C, 1D Fixed data-1 (Initialized data)
1E B4 D7 RECY current adj.
1F B4 D7
20 to 24 Fixed data-1 (Initialized data)
25 A0 A0 REC C/AFM current adj.
26 to 2E Fixed data-1 (Initialized data)
2F A6 A6 1.5 MHz deviation adj.
30 80 80 BPF f0adj.
31 to 4F Fixed data-1 (Initialized data)
50 67 79 LCD level adj. (VCO adj.)
51 79 67
52 84 84 LCD V-COM adj.
53 to 55 Fixed data-1 (Initialized data)
56 87 87 LCD White balance adj.
57 68 68
58 AF AF LCD level adj. (Contrast adj.)
59 to F3 Fixed data-1 (Initialized data)
F4 00 00
F5 00 00
F6 00 00
F7 00 00
F8 00 00
F9 00 00 Emergency memory
FA 00 00
FB 00 00
FC 00 00
FD 00 00
FE 00 00
FF 00 00

6-9
CCD-TRV138/TRV238E/TRV338/TRV438E
6. D PageTable
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address Initial value Remark
NTSC PAL
10 00 00 Test mode
11, 12 Fixed data-1 (Initialized data)
13 Fixed data-2
14 to 21 Fixed data-1 (Initialized data)
22
23
24 Fixed data-2
25
26
27 to 29 Fixed data-1 (Initialized data)
2A
2B Fixed data-2
2C to 35 Fixed data-1 (Initialized data)
36
37 Fixed data-2
38
39 Fixed data-1 (Initialized data)
3A Fixed data-2
3B to 55 Fixed data-1 (Initialized data)
56 Fixed data-2
57 Fixed data-1 (Initialized data)
58
59 Fixed data-2
5A to 6E Fixed data-1 (Initialized data)
6F Fixed data-2
70 to 7F Fixed data-1 (Initialized data)
7. E PageTable
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address Initial value Remark
NTSC PAL
00 to 30 Fixed data-1 (Initialized data)
31 Fixed data-2
32 to BF Fixed data-1 (Initialized data)
C0 Fixed data-2
C1 to FF Fixed data-1 (Initialized data)

6-10
CCD-TRV138/TRV238E/TRV338/TRV438E
8. F PageTable
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address Initial value Remark
NTSC PAL
10 80 80 28 MHz origin osillation adj.
11 Fixed data-1 (Initialized data)
12 50 50
Hall adj.
13 50 50
14 89 89
15 00 00
16 17 17
17 00 00
18 00 00
19 Fixed data-1 (Initialized data)
1A 36 36 LV standard data input
1B 00 00
1C to 29 Fixed data-1 (Initialized data)
2A 20 1E
Auto white balance
2B 05 36 standard data input
2C 07 07
2D F1 97
2E 15 13
Auto white balance adj.
2F 07 FC
30 0E 0E
31 85 14
32 Fixed data-1 (Initialized data)
33 36 36 Color reproduction adj.
34 Fixed data-1 (Initialized data)
35 28 27 Color reproduction adj.
36 to 39 Fixed data-1 (Initialized data)
3A FD FD Color reproduction adj.
3B F5 F4
3C, 3D Fixed data-1 (Initialized data)
3E 2C 2C
Auto white balance adj.
3F 80 40
40 58 59
41 10 C0
42, 43 Fixed data-1 (Initialized data)
44 28 28
Flange back adj.
45 EC EC
46 35 35
47 8F 8F
48 13 13
49 B8 B8
4A 00 00
4B 00 00
4C 00 00
4D 00 00
4E 2B 2B Flange back adj.
Address Initial value Remark
NTSC PAL
4F 19 19
Flange back adj.
50 00 00
51 32 32
52 04 04
53 00 00
54 00 00
55 to 59 Fixed data-1 (Initialized data)
5A FF FF Optical axis adj.
5B to FF Fixed data-1 (Initialized data)
9. 1F PageTable
Note 1: If reading/writing data on pages 1F, set data: 01 to page:
0, address: 10, and then select pages F. By this data set-
ting, the pages 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, A, C, D, E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, A, C, D, E, F, 1F Page Data”)
Address Initial value Remark
NTSC PAL
00 to FF Fixed data-1 (Initialized data)

6-11
CCD-TRV138/TRV238E/TRV338/TRV438E
1-3. CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the
specified values of “28 MHzOrigin OscillationAdjustment”, “LINE
OUT Level Adjustment” of “VIDEO SYSTEM ADJUSTMENT”
are satisfied.
Check that the data of page: 0, address: 10, is “00”.
If not, select page: 0, address: 10, and set data “00”
1. HALL Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
For detecting the position of lens iris, adjust the hall AMP gain
and offset.
Mode CAMERA
Subject Not required
Measurement Point Displayed data of page: 1 (Note 3)
Measuring Instrument Adjusting remote commander
Adjustment Page F
Adjustment Address 12 to 18
Specified value 87 to 8B during IRIS OPEN
15 to 19 during IRIS CLOSE
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 3: The right two digits of the page: 1 displayed data of the
adjusting remote commander.
1:00:XX
Displayed data
Adjusting method:
Order Page Address Data Procedure
10 0101
26 9489
36 9517
46 01 6D Press PAUSE button. (Note 4)
56 02 Check the data changes to
“01”.
66 01 00 Press PAUSE button.
Note 4: The adjustment data will be automatically input to page:
F, address: 12 to 18.
Checking method:
Order Page Address Data Procedure
16 0C Check that the data is “00” or
“10”.
20 0303
36 01 01 Press PAUSE button.
41 Check that the displayed data
(Note 3) during IRIS OPEN
satisfied the specified value.
56 01 03 Press PAUSE button.
61 Check that the displayed data
(Note 3) during IRIS CLOSE
satisfied the specified value.
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 9400
36 9500
40 0300
50 0100

6-12
CCD-TRV138/TRV238E/TRV338/TRV438E
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 13 Press PAUSE button.
46 01 27 Press PAUSE button. (Note 6)
56 02 Check the data changes to
“01”.
66 0C Check the data is “00”.
Note 6: The adjustment data will be automatically input to page:
F, address: 44 to 54.
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 01 25 Press PAUSE button.
36 01 00 Press PAUSE button.
46 4800
50 0100
6Perform “Flange Back
Check”.
2. Flange Back Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
(Using the minipattern box or flange back adjustment
jig)
The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated dur-
ing auto focusing/manual focusing.
Mode CAMERA
Subject Siemens star chart with ND filter for
minipattern box (Note 1) or flange
back adjustment jig
Measurement Point Check operation on monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 44 to 54
Specified value Data of page: 6, address: 0C is “00”
Note 1: Dark Siemens star chart.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 4: Perform the adjustment with the camcorder in horizon-
tal state.
Note 5: Perform “HALL Adjustment” before this adjustment.
Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DISPLAY (Menu setting) ............................................... LCD
Minipattern box
Below 3 cm
Camcorder
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supply
Output voltage :Specified voltage ±0.01 Vdc
Output current : more than 3.5 A
Preparations (Using the minipattern box)
1) The minipattern box is installed as shown in the following fig-
ure.
Note 7: The attachment lenses are not used.
2) Install the minipattern box so that the distance between it and
the front of lens of camcorder is less than 3 cm.
3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the
specified voltage ±0.01 Vdc.
5) Check that the center of Siemens star chart meets the center of
shot image screen with the zoom lens at TELE end andWIDE
end respectively.
Specified voltage: The specified voltage varies according to the
minipattern box, so adjust the power supply
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.
Fig. 6-1-6
PPreparation (Using the flange back adjustment jig)
(Luminance: about 300 lux)
1) Install the flange back adjustment jig so that the distance be-
tween it and the front of lens of camera is less than 3 cm.
2) Make the height of flange back adjustment jig and the camera
equal.
3) Check that the center of chart meets the center of shot image
screen with the zoom lens at TELE end andWIDE end respec-
tively.
Fig. 6-1-7
Flange back adjustment jig Below 3 cm
Camera

6-13
CCD-TRV138/TRV238E/TRV338/TRV438E
3-2. Flange Back Adjustment (2)
RadarWRadarWRadarW
Perform this adjustment after performing “Flange Back Adjust-
ment (1)”.
Mode CAMERA
Subject Subject more than 500 m away
(Subject with clear contrast such as
buildings, etc.)
Measurement Point Check operation on monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 44 to 54
Specified value Data of page: 6, address: 0C is “00”
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DISPLAY (Menu setting) ................................................ LCD
Preparations before adjustments:
1) Set the zoom lens to the TELE end and expose a subject that is
more than 500 m away.
(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the
screen)
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 13 Press PAUSE button.
4Place ND filter on the lens so that the optimum image is
obtain.
56 01 29 Press PAUSE button. (Note 3)
66 02 Check the data changes to
“01”.
76 0C Check the data is “00”.
Note 3: The adjustment data will be automatically input to page:
F, address: 44 to 54.
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 01 25 Press PAUSE button.
36 01 00 Press PAUSE button.
46 4800
50 0100
6Perform “Flange Back
Check”.
3. Flange Back Adjustment
(Using the flange back adjustment chart and
subject more than 500 m away)
The inner focus lens flange back adjustment is carried out auto-
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.
3-1. Flange Back Adjustment (1)
RadarW
RadarW
RadarW
RadarW
RadarW
Mode CAMERA
Subject Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)
Measurement Point Check operation on monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 44 to 54
Specified value Data of page: 6, address: 0C is “00”
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 3: Perform the adjustment with the camcorder in horizon-
tal state.
Note 4: Perform “HALL Adjustment” before this adjustment.
Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DISPLAY (Menu setting) ................................................ LCD
Preparations before adjustments:
1) Place the Flange back adjustment chart 2.0 m from the front
of the lens.
2) Check that the center of Flange back adjustment chart meets
the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 13 Press PAUSE button.
46 01 15 Press PAUSE button. (Note 5)
56 02 Check the data changes to
“01”.
66 0C Check the data is “00”.
Note 5: The adjustment data will be automatically input to page:
F, address: 44 to 54.
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 01 25 Press PAUSE button.
36 01 00 Press PAUSE button.
46 4800
50 0100
6Perform “Flange Back
Adjustment (2)”.

6-14
CCD-TRV138/TRV238E/TRV338/TRV438E
4. Flange Back Check
Mode CAMERA
Subject Siemens star
(2.0 m from the front of the lens)
(Luminance: approx. 200 lux)
Measurement Point Check operation on monitor TV
Measuring Instrument
Specified value Focused at the TELE end and WIDE
end
Note 1: Check that the data of page: 0, address: 10 is “00”.
Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DISPLAY (Menu setting) ................................................ LCD
Note 2: When the auto focus is ON, the lens can be checked if it
is focused or not by observing the data on the page: 1 of
the adjusting remote commander.
1 : 00 : XX Odd: Focused
Even: Unfocused
Checking method:
Order Page Address Data Procedure
1Place the Siemens star 2.0 m
from the front of the lens.
2
To open the IRIS, decrease
the luminous intensity to the
Siemens star up to a point
before noise appear on the
image.
36 4001
46 4101
5Shoot the Siemens star with
the zoom TELE end.
6Turn on the auto focus.
70 030F
81 Check that the lens is
focused. (Note 2)
96 2110
10 Shoot the Siemens star with
the zoom WIDE end.
11 Observe the TV monitor and check that the lens is
focused.
Processing after completing adjustment:
Order Page Address Data Procedure
16 2100
26 4000
36 4100
40 0300

6-15
CCD-TRV138/TRV238E/TRV338/TRV438E
5. Optical Axis Adjustment
Correct a deviation of optical axis between the lens and the CCD
imager.
If deviated, the screen center will be shifted when the lens is
zoomed from TELE end to WIDE end.
Subject Siemens Star
Measurement Point Check operation on monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 5A
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: “Flange Back Adjustment” must be already finished.
Switch setting:
1) DIGITAL ZOOM (Menu setting).................................... OFF
2) STEADYSHOT (Menu setting)
(CCD-TRV338/TRV438E only)...................................... OFF
3) DISPLAY (Menu setting) ................................................ LCD
Preparation for adjustment:
1) Play a monoscope portion of the System Check tape (WR5-
5NSP (NTSC) or WR5-5CSP (PAL)).
2) Stick the optical axis deviation specification frame to the moni-
tor screen so that the center of monoscope coincides with the
center of specification frame.
3) Select the CAMERA mode.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: F, address: 5A, and set data: 00, then press the
PAUSE button on the adjusting remote commander.
3) Place the Siemens Star at 2 m position away from the lens.
4) Shoot the Siemens Star with the zoom at TELE end.
5) Change the lens direction so that the center of Siemens Star
coincides with the center of optical axis deviation specifica-
tion frame.
6) Shoot the Siemens Star with the zoom at WIDE end.
7) Check on the monitor TV which area the center of Siemens
Star exists of the optical axis deviation specification frame.
At this time, measure the amount of deviation “L1” (distance
from the center of Siemens Star to the center of optical axis
deviation specification frame).
8) From the following table, read correction data according to
the area.
0
180
90
67.5
22.5
337.5
292.5
247.5
202.5 157.5
112.5
8
4
5
71
62
3
270
Fig. 6-1-8
Area
1
2
3
4
5
6
7
8
Deviation Phase
22.6°to 67.5°
67.6°to 112.5°
112.6°to 157.5°
157.6°to 202.5°
202.6°to 247.5°
247.6°to 292.5°
292.6°to 337.5°
337.6°to 22.5°
Correction Data
01
02
03
04
05
06
07
08
9) Select page: F, address: 5A, and set correction data, then press
the PAUSE button on the adjusting remote commander.
10) Shoot the Siemens Star with the zoom at TELE end.
11) Change the lens direction so that the center of Siemens Star
coincides with the center of optical axis deviation specifica-
tion frame.
12) Shoot the Siemens Star with the zoom at WIDE end.
13) Measure the amount of deviation “L2” (distance from the cen-
ter of Siemens Star to the center of optical axis deviation speci-
fication frame).
14) Compare L1 and L2, and make sure that the L2 is smaller than
L1.
If large, select page: F, address: 5A, and set data: 00, then
press the PAUSE button on the adjusting remote commander.
Processing after completion of adjustment:
1) Select page: 0, address: 01, and set data: 00.

6-16
CCD-TRV138/TRV238E/TRV338/TRV438E
Check on the oscilloscope
1. Horizontal period
A=B C=D
A
BC
D
E=F
V
EF
Color bar chart picture frame Monitor TV picture frame
Fig. 6-1-9
2. Vertical period
Fig. 6-1-10
Check on the monitorTV (Underscanned mode)
Fig. 6-1-11
6. Picture Frame Setting
Mode CAMERA
Subject Color bar chart
(Color reproduction adjustment
frame)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
Measurement Point Video terminal of A/V OUT jack
(75 Ωterminated)
Measuring Instrument Oscilloscope and monitor TV
Specified Value A=B, C=D, E=F
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Perform “Flange Back Adjustment” and “Optical Axis
Adjustment” before this adjustment.
Switch setting:
1) DIGITAL ZOOM (Menu setting).................................... OFF
2) STEADYSHOT (Menu setting)
(CCD-TRV338/TRV438E only) ...................................... OFF
3) DISPLAY (Menu setting) ................................................ LCD
Setting method:
1) Select page: 6, address: 48, and set data: 01.
2) Adjust the zoom and the camera direction, and set to the speci-
fied position.
3) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in following ad-
justments using “Color reproduction adjustment frame”.
Processing after completing camera system adjustments:
1) Select page: 6, address: 48, and set data: 00.

6-17
CCD-TRV138/TRV238E/TRV338/TRV438E
R-Y
B-Y
R
B
G
MG
YE
CY
Burst
R-Y
B-Y
R
B
G
M
G
Y
E
C
Y
Burst
7. Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
Mode CAMERA
Subject Color bar chart
(Color reproduction adjustment
frame)
Measurement Point Video terminal of A/V OUT jack
(75 Ωterminated)
Measuring Instrument Vectorscope
Adjustment Page F
Adjustment Address 33, 35, 3A, 3B
Specified Value All color luminance points should
settle within each color reproduction
frame.
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Perform “Flange Back Adjustment” before this adjust-
ment.
Note 3: NTSC model: CCD-TRV138/TRV338
PAL model: CCD-TRV238E/TRV438E
Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DIGITAL ZOOM (Menu setting).................................... OFF
3) STEADYSHOT (Menu setting)
(CCD-TRV338/TRV438E only)...................................... OFF
4) DISPLAY (Menu setting) ................................................ LCD
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 9D Set the following data.
68: NTSC model
67: PAL model
46 01 3D Press PAUSE button.
5F 80
Set the following data, and
press PAUSE button.
77: NTSC model
F7: PAL model
6
Adjust the GAIN and
PHASE of the vectorscope,
and set to the burst lumi-
nance point to the burst
position of color reproduc-
tion frame.
7F
Change the data and settle
each color luminance point in
each color reproduction
frame. (Note 4)
Note 4: Be sure to press the PAUSE button of the adjusting re-
mote commander before changing the addresses. If not,
the new data will not be written to the memory.
Fig. 6-1-12
NTSC model
PAL model
33
35
3A
3B
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 4800
36 9D00
40 0100

6-18
CCD-TRV138/TRV238E/TRV338/TRV438E
8. LV Standard Data Input
RadarW
RadarW
RadarW
RadarW
RadarW
Adjust the normal coefficient of the light value.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment frame)
Measurement Point Displayed data of page: 1 (Note 4)
Measuring Instrument Adjusting remote commander
Adjustment Page F
Adjustment Address 1A, 1B
Specified Value 0FE0 to 1020
Note 1: Perform “Flange Back Adjustment” before this adjust-
ment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 4: The right four digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX:XX
Displayed data
Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DIGITAL ZOOM (Menu setting).................................... OFF
3) STEADYSHOT (Menu setting)
(CCD-TRV338/TRV438E only)...................................... OFF
4) DISPLAY (Menu setting) ................................................ LCD
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 0D Press PAUSE button. (Note 5)
46 02 Check the data changes to
“01”.
50 031E
61 Check that the displayed data
(Note 4) satisfied specified
value.
Note 5: The adjustment data will be automatically input to page:
F, address: 1A and 1B.
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 4800
30 0300
40 0100
9. Auto White Balance Standard Data Input
RadarWRadarWRadarW
Adjust the white balance reference at 3200K.
Mode CAMERA
Subject Clear chart
(Color reproduction adjustment frame)
Adjustment Page F
Adjustment Address 2A to 2D
Note 1: Perform “Color Reproduction Adjustment” before this
adjustment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Switch setting:
1) NIGHTSHOT PLUS ........................................................ OFF
2) DIGITAL ZOOM (Menu setting).................................... OFF
3) STEADYSHOT (Menu setting)
(CCD-TRV338/TRV438E only)...................................... OFF
4) DISPLAY (Menu setting) ................................................ LCD
Adjusting method:
Order Page Address Data Procedure
10 0101
26 4801
36 01 11 Press PAUSE button.
46 01 0B Press PAUSE button. (Note 4)
56 02 Check the data changes to
“01”.
Note 4: The adjustment data will be automatically input to page:
F, address: 2A to 2D.
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button.
26 4800
30 0100