Sony DCR-TRV145E DCR-TRV147E DCR-TRV245E User manual

SERVICE MANUAL
•For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987621151.pdf).
•For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987621141.pdf).
•For MECHANISM ADJUSTMENTS, refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL IX
M2000 MECHANISM ” (9-929-861-11).
•Reference No. search on printed wiring boards is available.
•Table for differences of function of each model.
•When the machine needs to be repaired, make sure to follow the items of “LCDTYPE CHECK”.
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision History
Revision History
Ver 1.0 2003. 02
M2200 MECHANISM Photo: DCR-TRV250E
DCR-TRV145E/TRV147E/TRV245E/TRV250E
RMT-814
AEP Model
UK Model
East European Model
North European Model
DCR-TRV145E/TRV147E/TRV245E/
TRV250E
E Model
DCR-TRV147E/TRV250E
Australian Model
DCR-TRV147E/TRV250E
Chinese Model
DCR-TRV250E
Tourist Model
DCR-TRV250E
DIGITAL VIDEO CAMERA RECORDER

— 2 —
DCR-TRV145E/TRV147E/TRV245E/TRV250E
SPECIFICATIONS
COVER
COVER
Viewfinder
Electric Viewfinder (monochrome)
Image device
3 mm (1/6 type) CCD
(Charge Coupled Device)
Gross: Approx. 540 000 pixels
Effective: Approx. 350 000 pixels
Video camera
recorder
System
Video recording system
2 rotary heads
Helical scanning system
Audio recording system
Rotary heads, PCM system
Quantization: 12 bits (Fs 32 kHz,
stereo 1, stereo 2), 16 bits
(Fs 48 kHz, stereo)
Video signal
PAL colour, CCIR standards
Usable cassette
8 mm video format cassette
Recording/playback time
(using 90 min. Hi8/Digital8 video
cassette)
SP mode: 1 hour
LP mode: 1 hour and 30 minutes
Fastforward/rewind time
(using 90 min. Hi8/Digital8 video
cassette)
Approx. 5 min.
Input/output
connectors
S
Output
video jack
4-pin mini DIN
Luminance signal: 1 Vp-p,
75 Ω(ohms), unbalanced
Chrominance signal: 0.3 Vp-p,
75 Ω(ohms), unbalanced
Audio/Video
Output jack
AV MINIJACK,
VIDEO:
1 Vp-p, 75 Ω(ohms),
unbalanced, sync negative
AUDIO:
327 mV, (at output impedance more
than 47 kΩ(kilohms))
Output impedance with less than
2.2 kΩ(kilohms)
Stereo minijack (ø 3.5 mm)
LCD screen
Picture
6.2 cm (2.5 type)
50.3 ×37.4 mm
(2 ×1 1/2 in.)
Total dot number
123 200 (560 ×220)
General
Power requirements
7.2 V (Recahrgeable battery pack)
8.4 V (AC adaptor)
Average power consumption
(when using the battery pack)
During camera recording using
LCD
3.5 W
Viewfinder
2.7 W
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Recommended charging
temperature
10 °C to 30 °C (50 °F to 86 °F)
Storage temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Dimensions (approx.)
89 ×101 ×199 mm
(3 5/8 ×4 ×7 7/8 in.) (w/h/d)
Mass (approx.)
810 g (1 lb 12 oz)
main unit only
950 g (2 lb 1 oz)
including the rechargeable battery
pack NP-FM30, Hi8/Digital8 cassette,
lens cap and shoulder strap
AC adaptor
Power requirements
100 - 240 V AC, 50/60 Hz
Power consumption
18 W
Current consumption
0.35 – 0.18 A
Output voltage
DC OUT: 8.4 V, 1.5 A in the
operating mode
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Storage temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Dimensions (approx.)
56 ×31 ×100 mm
(2 1/4 ×1 1/4 ×4 in.) (w/h/d)
excluding projecting parts
Mass (approx.)
190 g (6.7 oz)
excluding mains lead
Recargeable
battery pack
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
5.0 Wh (700 mAh)
Operating temperature
0 °C to 40 °C (32 °F to 104 °F)
Dimensions (approx.)
38.2 ×20.5 ×55.6 mm
(1 9/16 ×13/16 ×2 1/4 in.)
(w/h/d)
Mass (approx.)
65 g (2.3 oz)
Type
Lithium ion
Design and specifications are
subject to change without notice.
DV jack
DCR-TRV147E/TRV250E:
Input/Output
4-pin connector
DCR-TRV145E/TRV245E:
Output
4-pin connector
DCR-TRV245E/TRV250E:
Mini-B
USB jack
Lens
Combined power zoom lens
Filter
DCR-TRV145E/TRV147E:
diameter 37 mm (1 7/16 in.)
20×(Optical), 560×
(Digital)
DCR-TRV245E/TRV250E:
20×(Optical), 700×
(Digital)
Focal length
f=2.5 – 50 mm (1/8 - 2 in.)
When converted to a 35 mm
still camera
f=42 – 840 mm (1 11/16 - 33 1/8 in.)
Colour temperature
Auto
Minimum illumination
4 lx (lux) (F 1.6)
0 lx (lux) (in the NightShot mode)*
*Objects unable to be seen due to
the dark can be shot with infrared
lighting.
SERIES
TM

— 3 —
DCR-TRV145E/TRV147E/TRV245E/TRV250E
Supplied accessories
1Wireless Remote Commander (1)
2AC-L15A/L15B AC Adaptor (1), Power
cord (1)
3NP-FM30 Rechargeable Battery Pack
(1)
DCR-TRV245E/TRV250E
DCR-TRV245E/TRV250E
DCR-TRV245E/TRV250E
AEP, UK, EE, NE
DCR-TRV245E/TRV250E
4Size AA (R6) battery for Remote
Commander (2)
5A/V connecting cable (1)
6Shoulder strap (1)
7Lens cap (1)
8USB cable (1)
9CD-ROM (SPVD-010 USB Driver) (1)
021-pin adaptor (1)
12
34
789
q;
65
•Abbreviation
AUS:Australian model
CH : Chinese model
EE : East European model
JE : Tourist model
NE : North European model
Table for differences of function
Model DCR-TRV145E DCR-TRV147E DCR-TRV245E DCR-TRV250E Remark
Destination AEP, UK, EE, NE AEP, UK, EE, NE, AEP, UK, EE, NE AEP, UK, EE, NE,
E, AUS E, AUS, CH, JE
Remote ✕✕aa
commander
Digital zoom 560x 560x 700x 700x
Steady shot ✕✕aa
VTR Rec ✕a✕aa: with REC button
DV jack DV OUT DV IN/OUT DV OUT DV IN/OUT
USB jack ✕✕aa
LCD type Please refer to page 1-2 to discriminate the type of LCD (TYPE C or TYPE S).

— 4 —
DCR-TRV145E/TRV147E/TRV245E/TRV250E
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1. Checktheareaofyourrepairforunsolderedorpoorly-soldered
connections. Checktheentireboardsurfaceforsoldersplashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for partswhich, throughfunctioning,show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270˚C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.

— 5 —
DCR-TRV145E/TRV147E/TRV245E/TRV250E
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Note for Repair ································································1-1
1-2. Power Supply During Repairs ·········································1-1
1-3. To Take Out a Cassette when not Eject (Force Eject) ·····1-2
1-4. LCD Type Check ·····························································1-2
1-5. Self-diagnosis Function ···················································1-3
1-5-1.Self-diagnosis Function ···················································1-3
1-5-2.Self-diagnosis Display·····················································1-3
1-5-3.Service Mode Display ·····················································1-3
1-5-4.Self-diagnosis Code Table ···············································1-4
2. DISASSEMBLY
Connection of Equipment················································2-2
2-1. Video Light ······································································2-3
2-2. PD-180 Board··································································2-4
2-3. LCD Module····································································2-5
Service Position to Check PD-180 Board ·······················2-5
2-4. Control Switch Block (PR-3000) ····································2-6
2-5. VF Lens (B) Assembly ····················································2-7
2-6. LB-090 Board··································································2-8
Service Position to Check LB-090 Board ·······················2-8
2-7. Cabinet (L) Assembly······················································2-9
2-8. F Panel BlockAssembly················································2-10
Service Position to Check SI-035 Board ·······················2-11
2-9. SI-035 Board ·································································2-12
2-10. Front Ring······································································2-12
2-11. Cabinet (R) Block Assembly ·········································2-13
Service Position to Check the Camera Section ·············2-13
2-12. Control Switch Block (CF-3000) ··································2-14
2-13. Hinge Assembly ····························································2-15
2-14. Control Switch Block (FK-3000) ··································2-16
2-15. EVF Block Assembly ····················································2-16
Service Position to Check VC-304 Board (SideA)·······2-17
2-16. Battery Panel Block Assembly ······································2-18
2-17. Control Switch Block (SS-3000)···································2-19
2-18. Lens Block Assembly ····················································2-19
2-19. FP-577 Flexible Board ··················································2-20
2-20. Cabinet (L) Section ·······················································2-21
2-21. VC-304 Board ·······························································2-21
Service Position to Check VC-304 Board (Side B)·······2-22
Service Position to Check the Mechanism Deck···········2-23
2-22. Mechanism Deck Block ················································2-24
2-23. Circuit Boards Location ················································2-25
2-24. Flexible Boards Location ··············································2-26
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram (1/5)···········································3-1
3-2. Overall Block Diagram (2/5)···········································3-3
3-3. Overall Block Diagram (3/5)···········································3-5
3-4. Overall Block Diagram (4/5)···········································3-7
3-5. Overall Block Diagram (5/5)···········································3-9
3-6. Power Block Diagram (1/2)···········································3-11
3-7. Power Block Diagram (2/2)···········································3-13
Section Title Page Section Title Page
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagrams
Frame Schematic Diagram (1/2) ·····································4-1
Frame Schematic Diagram (2/2) ·····································4-3
4-2. Schematic Diagrams························································4-5
CD-418 (CCD IMAGER)················································4-7
VC-304 (1/12)
(A/D CONVERTER, TIMING GENERATOR)··············4-9
VC-304 (2/12) (DV SIGNAL PROCESS) ····················4-11
VC-304 (3/12) (DV INTERFACE, VIDEO OUT) ········4-13
VC-304 (4/12) (LENS DRIVE) ····································4-15
VC-304 (5/12) (REC/PB AMP) ····································4-17
VC-304 (6/12) (SERVO) ···············································4-19
VC-304 (7/12) (CAMERA/MECHA CONTROL) ·······4-21
VC-304 (8/12) (HI CONTROL)····································4-23
VC-304 (9/12) (EVF DRIVE) ·······································4-25
VC-304 (10/12) (AUDIO PROCESS)···························4-27
VC-304 (11/12) (DC CONTROL) ································4-29
VC-304 (12/12) (CONNECTOR) ·································4-31
PD-180 (1/2)
(RGB DRIVE, TIMING GENERATOR) ······················4-33
PD-180 (2/2) (BACKLIGHT DRIVE) ··························4-35
LB-090 (EVF, EVF BACKLIGHT) ······························4-37
SI-035 (STEADYSHOT, MIC),
FP-569 FLEXIBLE ·······················································4-39
FP-577 FLEXIBLE ·······················································4-41
LS-057 (S/T REEL SENSOR), FP-228, FP-299,
FP-300, FP-301, FP-302 FLEXIBLE····························4-42
CF-3000, FK-3000 (CONTROL SWITCH BLOCK) ···4-43
SS-3000, PR-3000 (CONTROL SWITCH BLOCK)····4-45
4-3. Printed Wiring Boards ···················································4-47
CD-418 ··········································································4-49
VC-304 ··········································································4-51
PD-180···········································································4-55
LB-090···········································································4-59
SI-035 ············································································4-61
LS-057, FP-228, FP-299, FP-300, FP-301,
FP-302, FP-569, FP-577 FLEXIBLE····························4-63
4-4. Waveforms·····································································4-65
4-5. Mounted Parts Location ················································4-72
5. REPAIR PARTS LIST
5-1. Exploded Views ····························································5-2
5-1-1. Overall Assembly ··························································5-2
5-1-2. F Panel BlockAssembly ···············································5-3
5-1-3. Lens Block Assembly ···················································5-4
5-1-4. LCD Block Assembly ···················································5-5
5-1-5. Cabinet (R) Block Assembly ········································5-6
5-1-6. EVF Block Assembly····················································5-7
5-1-7. Battery Panel BlockAssembly······································5-8
5-1-8. MD Frame Block ··························································5-9
5-1-9. Cassette Compartment Assembly, Drum Assembly ···5-10
5-1-10. LS Chassis BlockAssembly ·······································5-11
5-1-11. Mechanism Chassis Block Assembly-1 ······················5-12
5-1-12. Mechanism Chassis Block Assembly-2 ······················5-13
5-2. Electrical Parts List ·····················································5-14

1-1
SECTION 1
SERVICE NOTE
DCR-TRV145E/TRV147E/TRV245E/TRV250E
COVER
COVER
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
1-2. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
The following method is available to prevent this.
Method 1.
Use the AC power adaptor (AC-L10, AC-VQ800 etc.).

1-2
DCR-TRV145E/TRV147E/TRV245E/TRV250E
1-3. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1Refer to “SECTION 2 DISASSEMBLY” to remove the mechanism deck block.
2Disconnect CN2401 (2P) of VC-304 board.
3Add +5V from the DC POWER SUPPLY and unload with a pressing the cassette compartment.
4Pull the timing belt in the direction of
arrow Awith a pincette while pressing
the cassette compartment (take care
not to damage) to adjust the bending
of a tape.
5Let go your hold the cassette
compartment and rise the cassette
compartment to take out a cassette.
Pincette
Timing belt
Timing belt
Press the cassette compartment not to
rise the cassette compartment
[DC power supply]
(+5V)
Adjust the bending of a tape
Disconnect CN2401
of VC-304 board.
Loading motor
A
A
1-4. LCD TYPE CHECK
By measuring the resistor value between Pin 6of CN5502 and Pin 0of CN5502 on PD-180 board, the type of LCD can be discriminated.
Note: About PD-180 board and LCD module, discriminate LCD type on the machine, and replace the same type.
PD-180 board CN5502
Resistor LCD type PD board
value
2.2 kΩTYPE S PD-180 (TYPE S)
3.3 kΩTYPE C PD-180 (TYPE C)
Multi CPC jig
(J-6082-311-A)
PD-180 board
CN5502
6pin
0pin
Volt ohm meter
+—

1-3
DCR-TRV145E/TRV147E/TRV245E/TRV250E
1-5. SELF-DIAGNOSIS FUNCTION
1-5-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
what to do. This function consists of two display; self-diagnosis
display and service mode display.
Detailsof the self-diagnosis functions are providedinthe Instruction
manual.
1-5-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
viewfinder or LCD shows a 4-digit display consisting of an alphabet
and numbers, which blinks at 3.2 Hz. This 5-character display
indicates the “repaired by:”, “block” in which the problem occurred,
and “detailed code” of the problem.
1-5-3. Service Mode Display
The service mode display shows up to six self-diagnosis codes shown in the past.
1. Display Method
While pressing the “STOP” key, set the switch from OFF to “VCR or PLAYER”, and continue pressing the “STOP” key for 5 seconds
continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
2. Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the
problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)
[1] : Occurred first time [3] : Occurred third time [5] : Occurred fifth time
[2] : Occurred second time [4] : Occurred fourth time [6] : Occurred the last time
3. End of Display
Turning OFF the power supply will end the service mode display.
Order of previous errors
Backup No. Self-diagnosis Codes
C : 3 1 : 1 1
[3]
Lights up
Viewfinder or LCD
[3] C : 3 1 : 1 1
1 1
3 1C
Repaired by:
Refer to “1-5-4. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder or LCD
C : 3 1 : 1 1
Control dial
Note: The “self-diagnosis display” data will be backed up by the lithium battery (CONTROL SWITCH BLOCK (CF-3000):
BT001).When removing the cabinet (R) (removing the VC-304 board CN1007), the “self-diagnosis display” data will
be lost by initialization.

1-4
DCR-TRV145E/TRV147E/TRV245E/TRV250E
1-5-4. Self-diagnosis CodeTable
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Block
Function
04
21
22
31
31
31
31
31
31
31
31
31
31
31
31
31
32
32
32
32
32
32
32
32
32
32
32
32
32
Detailed
Code
00
00
00
10
11
20
21
22
23
30
31
40
41
42
43
44
10
11
20
21
22
23
30
31
40
41
42
43
44
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading .
S reel side tape slacking when unloading .
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum operations.
PG fault during normal drum operations.
Phase fault during normal drum operations.
LOAD direction loading motor time-
out.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
S reel side tape slacking when
unloading.
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan
operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum
operations.
PG fault during normal drum
operations.
Phase fault during normal drum
operations.
Self-diagnosis Code
Repaired by:
Correction
Use the InfoLITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.

1-5E
DCR-TRV145E/TRV147E/TRV245E/TRV250E
E
E
E
E
Block
Function
61
61
62
62
Detailed
Code
00
10
00
01
Symptom/State
Difficult to adjust focus
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
(Withpitch angular velocitysensoroutput
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
Self-diagnosis Code
Repaired by:
Correction
Inspect the lens block focus reset sensor (Pin qs of CN1551 of
VC-304 board) when focusing is performed when the control dial
isrotatedin the focus manual mode and the focus motor drivecircuit
(IC1553 of VC-304 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin qg of CN1551 of
VC-304 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive circuit (IC1553 of VC-304
board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE751 of SI-035 board)
peripheral circuits. *1
Inspect yaw angular velocity sensor (SE752 of SI-035 board)
peripheral circuits. *1
*1: STEADYSHOT model (DCR-TRV245E/TRV250E)

2-1
SECTION 2
DISASSEMBLY
DCR-TRV145E/TRV147E/TRV245E/TRV250E
COVER
COVER
HELP
HELP
The following flow chart shows the disassembly procedure.
DCR-TRV145E/TRV147E/TRV245E/TRV250E
CONNECTION OF
EQUIPMENT
(Page 2-2)
SERVICE POSITION TO
CHECK THE CAMERA
SECTION (Page 2-13)
SERVICE POSITION TO
CHECK THE MECHANISM
DECK (Page 2-23)
SERVICE POSITION TO
CHECK VC-304 BOARD
(SIDE B) (Page 2-22)
SERVICE POSITION TO
CHECK VC-304 BOARD
(SIDE A) (Page 2-17)
SERVICE POSITION TO
CHECK SI-035 BOARD
(Page 2-11)
SERVICE POSITION TO
CHECK PD-180 BOARD
(Page 2-5)
SERVICE POSITION TO
CHECK LB-090 BOARD
(Page 2-8)
ASSEMBLE (FP-577
FLEXIBLE BOARD)
(Page 2-20)
2-1. VIDEO LIGHT
(Page 2-3)
2-2. PD-180 BOARD
(Page 2-4) 2-3. LCD MODULE
(Page 2-5)
2-9. SI-035 BOARD
(Page 2-12)
2-10. FRONT RING
(Page 2-12)
2-4. CONTROL SWITCH
BLOCK (PR-3000)
(Page 2-6)
2-13. HINGE
ASSEMBLY
(Page 2-15)
2-19. FP-577 FLEXIBLE
BOARD
(Page 2-20)
2-17. CONTROL SWITCH
BLOCK (SS-3000)
(Page 2-19)
2-16. BATTERY PANEL
BLOCK ASSEMBLY
(Page 2-18)
2-21. VC-304 BOARD
(Page 2-21)
2-20. CABINET (L)
SECTION
(Page 2-21)
2-22. MECHANISM
DECK BLOCK
(Page 2-24)
2-5. VF LENS (B)
ASSEMBLY
(Page 2-7)
2-6. LB-090
(Page 2-8)
2-8. F PANEL BLOCK
ASSEMBLY
(Page 2-10)
2-11. CABINET (R)
BLOCK ASSEMBLY
(Page 2-13)
2-12. CONTROL SWITCH
BLOCK (CF-3000)
(Page 2-14)
2-14. CONTROL SWITCH
BLOCK (FK-3000)
(Page 2-16)
2-15. EVF BLOCK
ASSEMBLY
(Page 2-16)
2-18. LENS BLOCK
ASSEMBLY
(Page 2-19)
2-7. CABINET (L)
ASSEMBLY
(Page 2-9)

2-2
DCR-TRV145E/TRV147E/TRV245E/TRV250E
[CONNECTION OF EQUIPMENT]
CPC lid
Screw
(M2)
Claw
CPC jig connector
Adjustment remote
commander (RM-95)
Info lithium battery
(L series)
I/F unit for LANC control
(J-6082-521-A)
AC power
adaptor
CPC jig connector
(J-6082-539-A)
CN712 Conductor side
16
1

2-3
DCR-TRV145E/TRV147E/TRV245E/TRV250E
Note: Follow the disassembly procedure in the numerical order given.
2-1. VIDEO LIGHT
1Push in the dent inside hole with wire tip.
2Video light
A
3Remove in the direction of the arrow A.4Halogen lamp

2-4
DCR-TRV145E/TRV147E/TRV245E/TRV250E
2-2. PD-180 BOARD
1Four screws (M1.7)
5Two screws
(M1.7)
8P cabinet (M) assembly
7Flexible board
(CN5702)
6Connector
(CN5701)
2Claw
4P cabinet (C)
Bottom View
3Claw
qs Claw
qa Screw (M1.7)
9Flexible board
(CN5601)
0Flexible board
(CN5501)
qd PD-180 board

2-5
DCR-TRV145E/TRV147E/TRV245E/TRV250E
2-3. LCD MODULE
[SERVICE POSITION TO CHECK PD-180 BOARD]
1Screw (M1.7)
3Claw
5Backlight unit
4P flame
6LCD module
2Boss
AC IN
AC power
adaptor
Adjustment remote
commander (RM-95)
Info lithium battery
(L series)
I/F unit for LANC control
(J-6082-521-A)
CPC jig connector
(J-6082-539-A)
Contacting surface
Multi CPC jig
(J-6082-311-A)
PD-180 board
LCD panel
Back light unit
CN5502

2-6
DCR-TRV145E/TRV147E/TRV245E/TRV250E
2-4. CONTROL SWITCH BLOCK (PR-3000)
1Two screws
(M1.7)
2Hinge bracket
3Two screws
(M1.7)
5Control switch block
(PR-3000)
4Claw

2-7
DCR-TRV145E/TRV147E/TRV245E/TRV250E
2-5. VF LENS (B) ASSEMBLY
When installing
VF lens (B) assembly,
slide the lever
in the arrow direction.
1Raise the EVF in the Adirection.
A
4EVF cabinet (upper)
2Two tapping screws
(M1.7)
5VF lens (B) assembly
6Flexible board
Slit
3Claw
VF lens (B) assembly
Slit

2-8
DCR-TRV145E/TRV147E/TRV245E/TRV250E
2-6. LB-090 BOARD
2Two claws
Handle with care,
these are fragile.
3Two claws
prism sheet
After removing the liquid
crystal indicator module,
over wrap with adhesive tape
and paper in order not to let
the illuminator and
the prism sheet fall down.
Lamp guide
When removing the liquid crystal indicator module,
do not face down the side which the board is mounted.
Otherwise, the illuminator and the prism sheet
may fall down.
illuminator
4Liquid crystal indicator module
5Claw
7LB-090 board
6Claw
1Flexible board
[SERVICE POSITION TO CHECK LB-090 BOARD]
AC IN
AC power
adaptor
Adjustment remote
commander (RM-95)
Info lithium battery
(L series)
I/F unit for LANC control
(J-6082-521-A)
CPC jig connector
(J-6082-539-A)
Contacting surface
LB-090 board
VF lens (B) assembly

2-9
DCR-TRV145E/TRV147E/TRV245E/TRV250E
2-7. CABINET (L) ASSEMBLY
4Two screws
(M2)
3Grip belt
5Screw
(M2)
6Two claws 1
2
7Cabinet (L) assembly

2-10
DCR-TRV145E/TRV147E/TRV245E/TRV250E
ONOFF
5Two screws
(M2)
6Two claws
2Screw
1Slide the NS knob to
the position of "ON".
0Screw
(M2) qa Screw
(M2)
3Two claws
qs Screw
(M2)
Top View
qd F panel block
assembly
4Ornamental ring
assembly
8Slide lever.
9
7Cabinet upper
Note: Remove it while taking
care as the flexible board
is connected.
2-8. F PANEL BLOCK ASSEMBLY