Sony CDX-F7000 - Fm/am Compact Disc Player User manual

1
Ver 1.0 2003. 12
Model Name Using Similar Mechanism CDX-S2000/SW200
CD Drive Mechanism Type MG-611XA-186//K
Optical Pick-up Name KSS1000E
SERVICE MANUAL
US Model
CDX-F7000/F7005X/FW700
Canadian Model
CDX-F7000/F7005X
CDX-F7000/F7005X/FW700
AUDIO POWER SPECIFICATIONS (US Model)
POWER OUTPUTAND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio 120 dB
Frequency response 10 – 20,000 Hz
Wow and flutter Below measurable limit
Tuner section
FM
Tuning range 87.5 – 107.9 MHz
Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 9 dBf
Selectivity 75 dB at 400 kHz
Signal-to-noise ratio 67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation 35 dB at 1 kHz
Frequency response 30 – 15,000 Hz
AM
Tuning range 530 – 1,710 kHz
Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity 30 µV
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output 52 W ×4 (at 4 ohms)
SPECIFICATIONS
General
Outputs Audio output terminals (front/rear)
Subwoofer output terminal (mono)
Power antenna relay control terminal
Power amplifier control terminal
Inputs Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input orAUX IN terminal
Remote controller input terminal
Antenna input terminal
Tone controls Bass ±10 dB at 62 Hz
Treble ±10 dB at 16 kHz
Loudness +8 dB at 100 Hz
+2 dB at 10 kHz
Power requirements 12 V DC car battery
(negative ground)
Dimensions Approx. 178 ×50 ×178 mm
(7 1/8 ×2 ×7 1/8 in.) (w/h/d)
Mounting dimensions Approx. 182 ×53 ×161 mm
(7 1/4 ×2 1/8 ×6 3/8 in.) (w/h/d)
Mass Approx. 1.3 kg (2 lb. 14 oz.)
Supplied accessories Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X118A
Design and specifications are subject to change without
notice.
• The tuner and CD sections have no adjustments.
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
9-961-473-01
2003L04-1
© 2003. 12
FM/AM COMPACT DISC PLAYER

2
CDX-F7000/F7005X/FW700
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
SERVICE NOTES
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
Notes on CD-R/CD-RW discs
•You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
•Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
•You cannot play a CD-R/a CD-RW that is not finalized*.
*Aprocess necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
optical pick-up
semi-fixed resistor

3
CDX-F7000/F7005X/FW700
zUNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
EXTENSION CABLE AND SERVICE POSITION
Whenrepairingorservicing thisset,connect the jig(extensioncable)
as shown below.
•Connect the MAIN board (CNP301) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-076-1).
SERVO BOAR
D
CN1
MAIN BOARD
CNP301 J-2502-076-1

4
CDX-F7000/F7005X/FW700
TABLE OF CONTENTS
1. GENERAL
Location of Controls................................................................ 5
Connections (CDX-F7000/F7005X) ....................................... 6
Connections (CDX-FW700).................................................... 7
2. DISASSEMBLY
2-1. Sub Panel Assy (CD)........................................................... 9
2-2. CD Mechanism Block ......................................................... 9
2-3. Main Board ....................................................................... 10
2-4. Chassis (T) Sub Assy ........................................................10
2-5. Roller Arm Assy ................................................................ 11
2-6. Chassis (OP) Assy ............................................................. 11
2-7. Optical Pick-up ................................................................. 12
2-8. SL Motor Assy (M902) ..................................................... 12
2-9. LE Motor Assy (M903) ..................................................... 13
2-10. Servo Board....................................................................... 13
3. DIAGRAMS
3-1. IC Pin Descriptions ........................................................... 14
3-2. Block Diagram –CD Section–........................................... 19
3-3. Block Diagram –Main Section–........................................20
3-4. Block Diagram –Display Section–....................................21
3-5. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................... 22
3-6. Waveforms......................................................................... 22
3-7. Circuit Boards Location .................................................... 22
3-8. Printed Wiring Boards –CD Mechanism Section–............ 23
3-9. Schematic Diagram –CD Mechanism Section– ................ 24
3-10. Schematic Diagram –Main Section (1/3)– ........................ 25
3-11. Schematic Diagram –Main Section (2/3)– ........................ 26
3-12. Schematic Diagram –Main Section (3/3)– ........................ 27
3-13. Printed Wiring Boards –Main Section– ............................ 28
3-14. Printed Wiring Board –Sub Section– ................................ 30
3-15. Schematic Diagram –Sub Section– ................................... 31
3-16. Printed Wiring Board –Key Section– ................................ 32
3-17. Schematic Diagram –Key Section–................................... 33
3-18. IC Block Diagrams............................................................ 34
4. EXPLODEDVIEWS
4-1. Main Section ..................................................................... 36
4-2. Front Panel Section ........................................................... 37
4-3. CD Mechanism Section (1) ............................................... 38
4-4. CD Mechanism Section (2) ............................................... 39
4-5. CD Mechanism Section (3) ............................................... 40
4-6. CD Mechanism Section (4) ............................................... 41
5. ELECTRICAL PARTS LIST......................................... 42

5
CDX-F7000/F7005X/FW700
4
Location of controls
Refer to the pages listed for details.
aDSPL (display mode change) button
12, 14, 21
bNumber buttons
Radio:
To store stations/receive stored stations.
CD/MD:
(1):REP
13
(2):SHUF 13
cDSO button 23
dMENU button
To display the menus.
eSOURCE (Power on/Radio/CD/MD*
1
/
AUX*
2
) button
To select the source.
fSEEK/AMS (</,) buttons
To skip tracks/fast-forward, reverse a track/
tune in stations automatically, find a station
manually/select a setting.
gSOUND button
20
hOFF (Stop/Power off) button
11, 24
iVOL (+/–) buttons
To turn up or down the volume.
jEQ7 button
22
Card remote commander RM-X118A
DISC
–
AT TOFF
REP
PTY
SHUF
DSPL
1
4
MODE
2
5
3
6
SOURCE
DISC
+
SEEK
+
SEEK
–
SOUND
ENTER
MENU
LIST
CAT
EQ7DSO
VOL
DISC
–
SOURCE
DISC
+
SEEK
+
SEEK
–
In menu mode, the currently selectable button(s) of
these four are indicated with a “
v ” in the display.
(SEEK) (<):
to select
leftwards
(DISC) (M):
to select upwards
(DISC) (m):
to select downwards
(SEEK) (,):
to select
rightwards
SECTION 1
GENERAL This section is extracted
from instruction manual.
5
kMODE button
To change operation.
lLIST (CAT)*
3
button 15, 18
mDISC (ALBUM) (M/m) buttons
To receive preset stations/change the disc*
4
,
skip albums*
5
/select a menu.
nENTER button
To enter a setting.
oATT button
20
*1 When an optional MD unit is connected.
*2 Available only when an optional Sony portable
device is connected to AUX IN terminal of the unit.
When you connect a Sony portable device and CD/
MD unit(s) at the same time, use the AUX IN
selector.
*3 The CAT button is available only when the XM
tuner is connected.
*4 When an optional CD/MD unit is connected.
*5 Available only when an optional CD unit with the
MP3 file control function is connected, and MP3 file
is played.
Note
If the display disappears by pressing
(OFF) , it cannot
be operated with the card remote commander unless
(SOURCE) on the unit is pressed, or a disc is inserted
to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery” on page 25.
Selecting a disc and album
Disc and album can be skipped using the DISC
(ALBUM) (M/m) buttons.
(With optional unit)
*6 Available only when an optional CD unit with the
MP3 file control function is connected, and MP3 file
is played.
Skipping tracks continuously
Press once either SEEK/AMS (<or ,)
button, then press again within about 1 second
and hold.
To Press
Skip discs
–Discselection Mor m[once for each disc]
Skip albums*
6
–Albumselection Mor m[hold for a moment] and release.
To continuously skip
albums, press (and hold)
within about 1 second of
first releasing the button.
6
The buttons on the unit share the same
functions as those on the card remote
commander.
a5SEEK/AMS (.m/M>)
buttons
bVolume control dial/SOUND button
Rotate to:
– Adjust the volume.
– Adjust the sound settings.
Press to:
– Select the sound items.
3qs DISC (ALBUM)/PRESET (+/–)
buttons
4MODE button
6DSO button
7SCRL (scroll) button
8Display window
9Z(eject) button (located on the front side
of the unit, behind the front panel) 10, 11
0OPEN button 9, 10, 11
qa Receptor for the card remote
commander
qd OFF (Stop/Power off) button*
qf EQ7 button
qg RESET button (located on the front side of
the unit, behind the front panel) 8
qh SOURCE button
qj Number buttons
qk DSPL (display mode change) button
ql IMAGE button 23
*Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold (OFF) on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.
P
U
S
H
S
O
U
N
D
DISC/
PRESET
MODE
DISC/
PRESET
SEEK
+
SEEK
– IMAGE
OFF
DSO
EQ7
SCRL
REP SHUF
6
OPEN
D
E
SOURCE DSPL1
S
2534
CDX-F7005X/F7000
6
The buttons on the unit share the same
functions as those on the card remote
commander.
a5SEEK/AMS (.m/M>)
buttons
bVolume control dial/SOUND button
Rotate to:
– Adjust the volume.
– Adjust the sound settings.
Press to:
– Select the sound items.
3qs DISC (ALBUM)/PRESET (+/–)
buttons
4MODE button
6DSO button
7SCRL (scroll) button
8Display window
9Z(eject) button (located on the front side
of the unit, behind the front panel) 10, 11
0OPEN button 9, 10, 11
qa Receptor for the card remote
commander
qd OFF (Stop/Power off) button*
qf EQ7 button
qg RESET button (located on the front side of
the unit, behind the front panel) 8
qh SOURCE button
qj Number buttons
qk DSPL (display mode change) button
ql IMAGE button 23
*Warning when installing in a car without
an ACC (accessory) position on the
ignition switch
After turning off the ignition, be sure to press
and hold (OFF) on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.
P
U
S
H
S
O
U
N
D
DISC/
PRESET
MODE
DISC/
PRESET
SEEK
+
SEEK
– IMAGE
OFF
DSO
EQ7
SCRL
REP SHUF
6
OPEN
D
E
SOURCE DSPL1
S
2534
CDX-FW700

6
CDX-F7000/F7005X/FW700
L
R
AUDIO OUT
FRONT
BUS AUDIO IN
/AUX IN
*
2
BUS
CONTROL IN
REMOTE
IN
AUDIO OUT
REAR
SUB OUT (MONO)
Schéma de raccordement (3)
1 À un point métallique de la voiture
Branchez d‘abord le fil de massenoir et, ensuite,
les fils d‘entrée d‘alimentation jaune et rouge.
2 Vers le fil de commande de l‘antenne électrique ou
le fil d‘alimentation de l‘amplificateur d‘antenne
Remarques
•Il n'est pas nécessairede raccorder ce fil s'il n'y a
pas d'antenne électrique ni d'amplificateur
d'antenne, ou avec une antenne télescopique
manuelle.
•Sivotre voiture est équipée d'une antenne FM/
AM intégrée dans la vitre arrière/latérale, voir
« Remarques sur les fils de commande et
d'alimentation ».
3 Au niveau du AMP REMOTE IN de l’amplificateur
de puissance en option
Ceraccordement s’applique uniquement aux
amplificateurs. Le branchement de tout autre
système risque d’endommager l’appareil.
4 Vers le cordon de liaison d’un téléphone de
voiture
5 Vers le connecteur du signal d’éclairage de la
voiture
Raccordez d’abord le fil de massenoir à un point
métallique du véhicule.
6 À la borne +12 V qui est alimentée quand la clé de
contact est sur la position accessoires
Remarques
•S'il n'y a pas de position accessoires,raccordez la
borne d'alimentation (batterie) +12 V qui est
alimentée en permanence.
Raccordez d’abord le fil de masse noir à un point
métallique du véhicule.
•Sivotre voiture est équipée d'une antenne FM/
AM intégrée dans la vitre arrière/latérale, voir
« Remarques sur les fils de commande et
d'alimentation ».
7 À la borne +12 V qui est alimentée en
permanence
Raccordez d’abord le fil de massenoir à un point
métallique du véhicule.
Remarques sur les fils de commande et
d’alimentation
•Le fil de commande de l’antenne électrique (bleu)
fournit une alimentation de + 12 V CClorsque vous
mettez la radio soustension.
•Lorsque votre voiture est équipée d’une antenne
FM/AM intégrée dans la vitre arrière/latérale,
raccordez le fil de commande de l’antenne (bleu)
ou l’entrée d’alimentation des accessoires (rouge)
à la borne d’alimentation de l’amplificateur
d’antenne existant. Pour plus de détails, consultez
votre détaillant.
•Une antenne électrique sansboîtier de relais ne
peut pas être utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le fil d’entrée d’alimentation jaune est
raccordé, le circuit de la mémoire est alimenté en
permanence même si la clé de contact est sur la
position d’arrêt.
Remarques sur le raccordement des haut-parleurs
•Avant de raccorder les haut-parleurs, mettez
l’appareil hors tension.
•Utilisez des haut-parleurs ayant une impédance de
4 à 8 ohms avec une capacité électrique adéquate
pour éviter de lesendommager.
•Ne raccordez pas les bornes du système de haut-
parleurs au châssisde la voiture et ne raccordez
pas les bornes des haut-parleurs droit à celles du
haut-parleur gauche.
•Ne raccordez pas le câble de massede cet appareil
à la borne négative (–) de l’enceinte.
•N’essayezpas de raccorder les haut-parleurs en
parallèle.
•Raccordez uniquement des haut-parleurs passifs.
Le raccordement de haut-parleurs actifs (avec
amplificateurs intégrés) aux bornes des haut-
parleurs peut endommager l’appareil.
•Pour éviter tout dysfonctionnement, n’utilisez pas
les fils des haut-parleurs intégrés installés dans
votre voiture si l’appareil partage un fil négatif
commun (–) pour les haut-parleurs droit et gauche.
•Ne raccordez pas entre eux les cordons des haut-
parleurs de l’appareil.
Remarque sur le raccordement
Si les haut-parleurs et l’amplificateur ne sont pas
raccordés correctement, le message« FAILURE»
s’affiche. Dans ce cas,assurez-vous que les haut-
parleurs et l’amplificateur sont bien raccordés.
Notes on the control and power supply leads
•The power antenna control lead (blue) supplies
+12 V DCwhen you turn on the tuner.
•When your car has built-in FM/AM antenna in the
rear/side glass,connect the power antenna control
lead (blue) or the accessorypower input lead (red)
to the power terminal of the existing antenna
booster.For details, consult your dealer.
•Apower antenna without a relay box cannot be
used with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
Notes on speaker connection
•Before connecting the speakers, turn the unit off.
•Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
•Do not connect the speaker terminals to the car
chassis,or connect the terminals of the right
speakers with those of the left speaker.
•Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
•Do not attempt to connect the speakers in parallel.
•Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
•To avoid a malfunction, do not use the built-in
speaker leads installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
•Do not connect the unit’s speaker leads to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case,make
sure the speaker and amplifier are connected
correctly.
3
Source selector
(not supplied)
Sélecteur de source
(non fourni)
XA-C30
AMP REM
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Fuse (10 A)
Fusible (10 A)
Blue/white striped
Rayé bleu/blanc
White
Blanc
Green
Vert
Purple
Mauve
White/black striped
Rayé blanc/noir
Gray/black striped
Rayé gris/noir
Green/black striped
Rayé vert/noir
Purple/black striped
Rayé mauve/noir
Gray
Gris
Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
3
*
6
from car antenna
à partir de l’antenne de la voiture
Left
Gauche
Right
Droit
Left
Gauche
Right
Droit
2
5
6
4
ANT REM
4
Red
Rouge
Yellow
Jaune
Black
Noir
Blue
Bleu
Light blue
Bleu ciel
Max. supply current 0.1 A
Courant max. fourni 0,1 A
ATT
1
*
1
*1 RCApin cord (not supplied)
*2 Besureto match the color-coded
cordfor audio to the appropriate
jacksfrom the unit. If you connectan
optional CD/MD unit, you cannot use
AUX IN terminal.
*3 Auxiliary optional equipment such
asportable DVD player (not
supplied)
*4 Suppliedwith the auxiliary
equipment
*5 Suppliedwith XA-C30
*6 Insert with the cord upwards.
*1 Cordonà broche RCA(non fourni)
*2 Veillez à faire correspondrele code
couleuraudio aux fichesde
l’appareil. Sivous raccordezun
appareil CDou MD en option, vous
ne pouvez pasutiliserla borne AUX
IN.
*3 Appareil auxiliaire en option, par
exemple un lecteur de DVD
portable (non fourni)
*4 Fourniavecl’appareil auxiliaire
*5 Fourni avec le XA-C30
*6 Insérezavecle câbleversle bas.
*
4
*
3
*
5
*
1
7
Orange/white striped
Rayé orange/blanc
ILLUMINATION
Connection diagram (3)
1 To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
•It is not necessaryto connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
•When your car has a built-in FM/AM antenna in
the rear/side glass,see“Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black ground lead to a
metal surface of the car first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
•If there is no accessoryposition, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
•When your car has a built-in FM/AM antenna in
the rear/side glass,see“Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
Connections (CDX-F7000/F7005X)

7
CDX-F7000/F7005X/FW700
L
R
AUDIO OUT
FRONT
BUS AUDIO IN
/AUX IN
*
2
SUB OUT (MONO)
BUS
CONTROL IN
REMOTE
IN
AUDIO OUT
REAR
Diagrama de conexión (3)
1 A una superficie metálica del automóvil
Conecte primero el cable de toma a tierra negro, y
después los cables con raya naranja/blanca,
amarillo, y rojo de entrada de alimentación.
2 Al cable de control de la antena motorizada o al
cable de fuente de alimentación del amplificador
de antena
Notas
•Sino sedispone de antena motorizada ni de
amplificador de antena, o se utiliza una antena
telescópica accionada manualmente, no será
necesario conectar este cable.
•Siel automóvil incorpora una antena de FM/AM
en el cristal trasero o lateral, consulte “Notas
sobre los cables de control y de fuente de
alimentación”.
3 Para conectar a AMP REMOTE IN del amplificador
de potencia opcional
Estaconexión es sólo para amplificadores. La
conexión de cualquier otro sistema puede dañar la
unidad.
4 Al cable de interfaz de un teléfono para automóvil
5 A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de toma a
tierra negro a una superficie metálica del
automóvil.
6 Al terminal de alimentación de +12 V que recibe
energía en la posición de accesorio del interruptor
de la llave de encendido
Notas
•Sino hay posición de accesorio, conéctelo al
terminal de alimentación (batería) de +12 V que
recibe energía sin interrupción.
Asegúrese de conectar primero el cable de toma
a tierra negro a una superficie metálica del
automóvil.
•Siel automóvil incorpora una antena de FM/AM
en el cristal trasero/lateral, consulte “Notas sobre
los cables de control y de fuente de
alimentación”.
7 Al terminal de alimentación de +12 V que recibe
energía sin interrupción
Asegúrese de conectar primero el cable de toma a
tierra negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de
alimentación
•El cable de control de la antena motorizada (azul)
suministrará ccde + 12V cuando conecte la
alimentación del sintonizador.
•Siel automóvil dispone de una antena de FM/AM
incorporada en el cristal trasero o lateral, conecte
el cable de control de antena motorizada (azul) o
el cable de entrada de alimentación auxiliar (rojo)
al terminal de alimentación del amplificador de
antena existente. Para obtener más información,
consulte a su proveedor.
•Con esta unidad no esposible utilizar una antena
motorizada sin caja de relé.
Conexión para protección de la memoria
Siconecta el conductor de entrada amarillo, el
circuito de la memoria recibirá siempre
alimentación, aunque apague la llave de encendido.
Notas sobre la conexión de los altavoces
•Antes de conectar los altavoces, desconecte la
alimentación de la unidad.
•Utilice altavoces con una impedancia de 4 a 8
Ω
con la capacidad de potencia adecuada para evitar
que sedañen.
•No conecte los terminales de altavoz al chasisdel
automóvil, ni conecte los terminales del altavoz
derecho con los del izquierdo.
•No conecte el cable de toma a tierra de esta
unidad al terminal negativo (–) del altavoz.
•No intente conectar los altavoces en paralelo.
•Conecte solamente altavoces pasivos. Siconecta
altavoces activos (con amplificadores incorporados)
a los terminales de altavoz, puede dañar la unidad.
•Para evitar fallos de funcionamiento, no utilice los
cables de altavoz incorporados instalados en el
automóvil si su unidad comparte un cable negativo
común (–) para los altavoces derecho e izquierdo.
•No conecte los cables de altavoz de la unidad entre
sí.
Nota sobre la conexión
Siel altavoz y el amplificador no están conectados
correctamente, aparecerá “Failure” en la pantalla. Si
esasí,compruebe la conexión de ambos dispositivos.
Notes on the control and power supply leads
•The power antenna control lead (blue) supplies
+12 V DCwhen you turn on the tuner.
•When your car has built-in FM/AM antenna in the
rear/side glass,connect the power antenna control
lead (blue) or the accessorypower input lead (red)
to the power terminal of the existing antenna
booster.For details, consult your dealer.
•Apower antenna without a relay box cannot be
used with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
Notes on speaker connection
•Before connecting the speakers, turn the unit off.
•Usespeakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
•Do not connect the speaker terminals to the car
chassis,or connect the terminals of the right
speakers with those of the left speaker.
•Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
•Do not attempt to connect the speakers in parallel.
•Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
•To avoid a malfunction, do not use the built-in
speaker leads installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
•Do not connect the unit’s speaker leads to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“Failure” appears in the display. In this case,make
sure the speaker and amplifier are connected
correctly.
3
Source selector
(not supplied)
Selector de fuente
(no suministrado)
XA-C30
AMP REM
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
Fuse (10 A)
Fusible (10 A)
Blue/white striped
Con rayas azules y blancas
White
Blanco
Green
Verde
Purple
Morado
White/black striped
Con rayas blancas y negras
Gray/black striped
Con rayas grises y negras
Green/black striped
Con rayas verdes y negras
Purple/black striped
Gray
Gris
Supplied with the CD/MD changer
Suministrado con el cambiador de CD/MD
3
*
6
from car antenna
desde la antena del automóvil
Left
Izquierdo
Right
Derecho
Left
Izquierdo
Right
Derecho
2
5
6
4
ANT REM
4
Red
Rojo
Yellow
Amarillo
Black
Negro
Blue
Azul
Light blue
Azul celeste
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
ATT
1
*
1
*1 RCApin cord (not supplied)
*2 Besureto match the color-coded
cordfor audio to the appropriate
jacksfrom the unit. If you connectan
optional CD/MD unit, you cannot use
AUX IN terminal.
*3 Auxiliary optional equipment such
asportable DVD player
(not supplied)
*4 Suppliedwith the auxiliary
equipment
*5 Suppliedwith XA-C30
*6 Insert with the cord upwards.
*1 Cable conterminales RCA
(no suministrado)
*2 Asegúresede hacer coincidirel
códigocodificadoconcolorespara
audio con las tomas apropiadas de
la unidad. Siconectauna unidad de
CD/MD opcional,no podrá utilizar
el terminal AUX IN.
*3 Equipo opcional auxiliar como un
reproductor de DVD portátil
(no suministrado)
*4 Suministradoconel equipo auxiliar
*5 Suministradoconel XA-C30
*6 Insertar con el cable haciaarriba.
*
4
*
3
*
5
*
1
7
Orange/white striped
Con rayas naranjas y blancas
ILLUMINATION
Con rayas violetas y negras
Connection diagram (3)
1 To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
•It is not necessaryto connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass,see“Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black ground lead to a
metal surface of the car first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
•If there is no accessoryposition, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass,see“Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
Connections (CDX-FW700)

8
CDX-F7000/F7005X/FW700 SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
2-1. SUB PANEL ASSY (CD)
(Page 9)
2-2. CD MECHANISM BLOCK
(Page 9)
SET
2-3. MAIN BOARD
(Page 10) 2-4. CHASSIS (T) SUB ASSY
(Page 10)
2-5. ROLLER ARM ASSY
(Page 11)
2-6. CHASSIS (OP) ASSY
(Page 11)
2-8. SL MOTOR ASSY (M902)
(Page 12)
2-10. SERVO BOARD
(Page 13)
2-7. OPTICAL PICK-UP
(Page 12) 2-9. LE MOTOR ASSY (M903)
(Page 13)

9
CDX-F7000/F7005X/FW700
2-2. CD MECHANISM BLOCK
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY (CD)
2 two claw
s
3 two claws
5 sub panel assy (CD)
1 two screws
(+PTT 2.6
x 6)
CN601
4
7 bracket (CD)
5 CD mechanism block
4 CNP301
3
1 screw
(+PTT 2.6 x 6
)
2 screw
(+PTT 2.6 x 6)
6 two screws
(+PTT 2.6 x 6)

10
CDX-F7000/F7005X/FW700
2-4. CHASSIS (T) SUB ASSY
2-3. MAIN BOARD
1 three ground point screws
(+PTT 2.6 x 6)
3 MAIN board
4 CN401
2 two screws
(+PTT 2.6
x 8)
5 two screws
(+PTT 2.6
x 8
)
6 cord
5 SENSOR board
6 chassis (T) sub assy
4 claw
1 two screws
(+P 1.7
x 2.2)
2 two screws
(+P 1.7
x 2.2)
3 claw

11
CDX-F7000/F7005X/FW700
2-5. ROLLER ARM ASSY
2-6. CHASSIS (OP) ASSY
3 washer (1.1 – 2.5)
4 worm wheel (RA)
5 roller arm assy
1 spring (RAL)
2 spring (RAR)
4 washer
0 compression spring (damper)
9 two compression springs (damper
)
qa chassis (OP) assy
5 gear (LE1)
1 CN2
lever (D)
slider (R)
6
7
8
2 Remove the six solderings.
3 tension coil spring (KF)

12
CDX-F7000/F7005X/FW700
2-7. OPTICAL PICK-UP
2-8. SL MOTOR ASSY (M902)
1 tension coil spring (CHKG)
2 chucking arm sub assy
3 screw
(+B 1.4
x 5)
4 rack (SL)
5 claw
6 main shaft
7 optical pick-up
1 screw
(+P 1.4 x 1.8)
2 SL motor assy (M902)

13
CDX-F7000/F7005X/FW700
2-9. LE MOTOR ASSY (M903)
2-10. SERVO BOARD
2 washer
4
qd
3
gear (LE1)
7 leaf spring (LE)
5
lever (D)
bracket (LEM)
slider (R)
6 screw
(+P 1.7
x 2.2)
8 screw
(+M 1.7
x 2.5)
qa screw
(+M 1.7
x 2.5)
qf two toothed lock screws
(+M 1.4
)
qs screw
(+M 1.7
x 2.5)
9 bearing (LEB)
0 woam (LEB) assy
qg LE motor assy
(M903)
1 Remove the soldering.
3 CN2
5 claw
6 SERVO board
4 toothed lock screw
(M 1.7)
1 Remove the eight solderings.
2 Remove the three solderings.

14
CDX-F7000/F7005X/FW700
3-1. IC PIN DESCRIPTIONS
• IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)
Pin No. Pin Name I/O Pin Description
1LDOLaser diode ON/OFF control signal output (L: laser OFF, H: laser ON)
2PDIDimmer monitor input from optical pick-up laser diode.
3PNINot used. (Fixed at L in this set)
4AVDD — Analog power supply pin (+3.3V)
5DGND — Ground
6 RFOK O RFOK signal output to system control IC.
7INTQ O CD text pack synchronization signal output to system control IC.
8RST I CD reset signal input from system control IC.
9A0I
Command/parameter discrimination signal input from system control IC.
(L: command transmission, H: parameter transmission)
10 STB I Data strobe signal input from system control IC.
11 SCK I Serial clock input from system control IC.
12 SO O Serial data output to system control IC.
13 SI I Serial data input from system control IC.
14 DVDD — Power supply pin (+3.3V)
15 DAVDD — D/A converter power supply (+) pin (+3.3 V)
16 ROUT O Analog audio signal output (R-ch)
17 DAGND — Ground
18 REGC — Capacitor connection pin for SCF regulator.
19 DAGND — Ground
20 LOUT O Analog audio signal output (L-ch)
21 DAVDD — D/A converter power supply (+) pin (+3.3 V)
22 XVDD — Power supply pin (+3.3V)
23 XTAL O Main system clock output (16.9344 MHz)
24 XTAL I Main system clock input (16.9344 MHz)
25 XGND — Ground
26 DVDD — Power supply pin (+3.3V)
27 C1D1/FZD O Not used. (Open)
28 C1D2/TZD O Not used. (Open)
29 C2D1/RMUTE O CD R-ch data zero detection signal output
30 C2D2/LMUTE O CD L-ch data zero detection signal output
31 C2D3/SHOCK/SBSY O Not used. (Open)
32 LOCK/FR O Not used. (Open)
33 WFCK/MIRR O Not used. (Open)
34 RFCK/HOLD O Not used. (Open)
35 PLCK O Not used. (Open)
36 C16M O Not used. (Open)
37 DGND — Ground
38 TX O Not used. (Open)
39 EMPH/RAMOVER O Not used. (Open)
40 FLAG O Not used. (Open)
41 DVDD — Power supply pin (+3.3V)
42 LIMIT I Not used. (Fixed at L in this set)
43 XTALEN I Oscillation circuit ON/OFF control signal input (L: ON, H: OFF)
(Fixed at L in this set)
44 DGND — Ground
45 DIN I Not used. (Connect to DOUT in this set)
46 DOUT O Not used. (Connect to DIN in this set)
47 SCKIN I Not used. (Connect to SCKO in this set)
48 SCKO O Not used. (Connect to SCKIN in this set)
49 LRCKIN I Not used. (Connect to LRCK in this set)
SECTION 3
DIAGRAMS

15
CDX-F7000/F7005X/FW700
Pin No. Pin Name I/O Pin Description
50 LRCK O Not used. (Connect to LRCKIN in this set)
51 DVDD — Power supply pin (+3.3 V)
52 FD+ O Focus servo drive PWM signal output (+)
53 FD– O Focus servo drive PWM signal output (–)
54 TD+ O Tracking servo drive PWM signal output (+)
55 TD– O Tracking servo drive PWM signal output (–)
56 SD+ O Sled servo drive PWM signal output (+)
57 SD– O Sled servo drive PWM signal output (–)
58 MD+ O Spindle servo drive PWM signal output (+)
59 MD– O Spindle servo drive PWM signal output (–)
60 DGND — Ground
61 TESTEN I Test setting input (Fixed at L in this set)
62 to 66 TEST4 to TEST0 I Test setting input (Fixed at L in this set)
67 ADGND — A/D converter power supply (–) pin
68 EFM O EFM signal output
69 ASY I EFM comparator reference voltage input
70 ADVDD — A/D converter power supply pin (+3.3 V)
71 RFI I RF signal input for EFM data growing.
72 EQ2 — Not used. (Open)
73 EQ1 — RF amplifier equalizer parts connection pin
74 RF– I Not used. (Open)
75 RF2– I RF amplifier inversion input
76 AGCO O RF signal output after on AGC.
77 AGCI I RF AGC signal amplifier input
78 RFO O RF signal output before on AGC.
79 ATEST I Not used. (Open)
80 C3T — Capacitor connection pin for 3T detection.
81 AGND — Ground
82 A I Signal input (A) from optical pick-up detector.
83 C I Signal input (C) from optical pick-up detector.
84 B I Signal input (B) from optical pick-up detector.
85 D I Signal input (D) from optical pick-up detector.
86 F I Signal input (F) from optical pick-up detector.
87 E I Signal input (E) from optical pick-up detector.
88 VREFIN I Reference voltage (+1.65 V) input
89 AVDD — Analog power supply pin (+3.3 V)
90 REFOUT O Reference voltage (+1.65 V) output
91 REFC — Capacitor connection pin for reference voltage output.
92 FE– I Focus error signal amplifier inversion input
93 FEO O Focus error signal amplifier output
94 ADCIN I Not used. (Open)
95 TE- I Tracking error signal amplifier inversion input
96 TEO O Tracking error signal amplifier before output
97 TE2 O Tracking error signal amplifier after output
98 TEC I Tracking error signal comparator input
99 AGND — Ground
100 PWMSW I Not used. (Fixed at L in this set)

16
CDX-F7000/F7005X/FW700
• IC303 M30624MGP (SYSTEM CONTROL) (MAIN BOARD (3/3))
Pin No. Pin Name I/O Pin Description
1SIRCS I Remocon data input
2(NCO) O Not used
3CD SO/TSO O CD servo serial data output
4CD SI/TSI I CD servo serial data input
5CD CKO/TCKO O CD servo serial clock output
6BYTE I Connecting to ground.
7CNVSS I Flash write-in signal input
8XCIN I Sub clock signal input (32.768kHz)
9XCOUT O Sub clock signal output (32.768kHz)
10 RESET I CPU reset input
11 XOUT O Main clock signal output (6MHz)
12 VSS — Ground
13 XIN I Main clock signal input (6MHz)
14 VCC1 — Ground
15 NMI I Non maskable interrupt signal input
16 CD INTQ I CD-TEXT sync. signal input
17 DAVN I RDS data block sync. detection signal input
18 BU IN I Back-up power detection signal input
19 NS MASK O NS-MASK signal output
20 BEEP O Beep signal output
21 FSW IN I DD converter OSC frequency count input
22 FSW OUT O DD converter OSC frequency change output
23 SA CLK O Spectrum analyzer clock output
24 TEL ATT I Telephone mute signal input
25 ATT O Mute signal output
26 VOL ATT O Electronic volume mute signal output
27 I2C CKO O I2C bus serial clock output
28 I2C SIO O I2C bus serial data output
29 UNI SO O SONY bus serial data output
30 UNI SI I SONY bus serial data input
31 UNI CKO O SONY bus serial clock output
32 TUNER ATT O Tuner mute signal output
33 EE SIO I/O Tuner pack EEPROM serial data input/output
34 EE CKO O Tuner pack EEPROM serial clock output
35 RE IN0 I Rotary encoder signal input 0
36 RE IN1 I Rotary encoder signal input 1
37 NOSE SW I Front panel detection signal input
38 DOOR SW I Panel open detection signal input
39 HOLD I External bus data input (HOLD)
40 AMP DIAG I AMP self-diagnosis function control signal input
41 AMP STB O AMP standby signal output
42 (NCO) O Not used
43 (NCO) O Not used
44 WRI/WR I External bus data input (WRI/WR)
45 CD LIMIT I CD LIMIT switch detection signal input
46 CD D SW I CD D switch detection signal input
47 CD IN SW I CD IN switch detection signal input
48 4V SEL I 4V PRE-OUT select signal input
49 MP3 SEL I Deck mechanism select signal input
50 DST SEL1 I Destination select setting pin 1
51 DST SEL2 I Destination select setting pin 2
52 CD LM LOAD O CD loading signal output

17
CDX-F7000/F7005X/FW700
Pin No. Pin Name I/O Pin Description
53 CD LM EJECT O CD eject signal output
54 CD RESET O CD reset signal output
55 CD AO O CD AO signal output
56 CD STB O CD strobe signal output
57 (NCO) O Not used
58 CD RF OK I CD RF OK signal input
59 CD ON I CD ON signal input
60 VCC2 — Power supply pin (+5V)
61 DISP RESET O Display CPU reset signal output
62 VSS — Ground
63 TEST IN I Test mode signal input
64 BUS ON O BUS ON signal output
65 SYS RST O System reset signal output
66 BUS/AUX O BUS AUDIO/AUX-IN select signal output
67 (NCO) O Not used
68 ACC IN I ACC power supply check signal input
69 ILL IN I ILL check signal input
70 RC IN1 I Rotary commander signal input
71 CDM ON I CD power supply ON signal input
72 CD SELF SW I CD SELF switch detection signal input
73 TU ATT IN I Tuner attenuator zero cross signal input
74 ZERO DET1 I ZERO detection signal input 1
75 ZERO DET2 I ZERO detection signal input 2
76 Z ATT I Z mute signal input
77 (NCO) O Not used
78 (NCO) O Not used
79 ROMC EN O Connecting to ground.
80 QUALITY I Tuner noise detection signal input
81 MPTH O Not used
82 VSM I S-meter signal input
83 SA IN I Spectrum analyzer data input
84 KEY IN1 I Key signal input
85 KEY IN0 I Key signal input
86 RC IN0 I Rotary commander signal input
87 KEYACK2 I Rotary commander ACK signal input
88 KEYACK0 I KeyACK signal input
89 KEYACK1 I KeyACK signal input
90 DOORING O Sub panel LED power supply control signal output
91 RAM BU I RAM back-up input
92 FLD ON O FL driver power supply control signal output
93 FL ON O FL power supply control signal output
94 AVSS — Ground
95 DISP CE O Display CPU chip enable output
96 VREF — AD converter reference voltage (+5V)
97 AVCC — Power supply pin (+5V)
98 DISP SI/RX I Display CPU serial data input
99 DISP SO/TX O Display CPU serial data output
100 DISP CKO O Display CPU serial clock output

18
CDX-F7000/F7005X/FW700
• IC901 M30823MH-080GP (DISPLAY CONTROL) (KEY BOARD)
Pin No. Pin Name I/O Pin Description
1SYS CE I Main chip enable input
2(NCO) O Not used
3FL DAT3 O FL serial data output 3
4(NCO) O Not used
5FL CLK IN I FL serial clock input
6BYTE I Connecting to ground.
7CNVSS I Flash write-in signal input
8PLL LPF O PLL low pass filter connection pin
9PLL GND I Ground
10 RESET I CPU reset input
11 XOUT O Main clock signal output (8MHz)
12 VSS — Ground
13 XIN I Main clock signal input (8MHz)
14 VCC — Power supply pin (+5V)
15 NMI I Non maskable interrupt signal input
16 (NCO) O Not used
17 GCP IN I GCP pulse interrupt signal input
18, 19 (NCO) O Not used
20 GCP OUT O GCP pulse signal output
21 LAT O FL data LAT output
22 BK O FL BK signal output
23 GCP2 O FL GCP signal output 2
24 (NCO) O Not used
25 GCP1 O FL GCP signal output 1
26 (NCO) O Not used
27 GCP4 O FL GCP signal output 4
28 GCP3 O FL GCP signal output 3
29 SYS SO O Main bus serial data output
30 SYS SI I Main bus serial data input
31 SYS CLK O Main bus serial clock output
32 (NCO) O Not used
33 FL DAT1 O FL serial data output 1
34 (NCO) O Not used
35 FL CLK O FL serial clock output
36 to 38 (NCO) O Not used
39 HOLD I External bus data input (HOLD)
40 to 43 (NCO) O Not used
44 WRI/WR I External bus data input (WRI/WR)
45 to 59 (NCO) O Not used
60 VCC — Power supply pin (+5V)
61 (NCO) O Not used
62 VSS — Ground
63 to 93 (NCO) O Not used
94 AVSS — Ground
95 (NCO) O Not used
96 VREF — Reference voltage (+5V)
97 AVCC — Power supply pin (+5V)
98 (NCO) — Not used
99 FL DAT2 O FL serial data output 2
100 FL CLK IN I FL serial clock input

19 19
CDX-F7000/F7005X/FW700
82
83
84
85
20
16
D/A
CONV
TRACKING
ERROR
FORCUS
ERROR
1
OSC
EFM
DEMOD
SERVO
CTL
RF
EQ
13
12
11
10
9
8
6
47
72
45
46
3
4
5
56
55
54
58
I/F
87
86
2
1
LD
DRIVE
Q1
FOCUS
COIL
DRIVE
TRACKING
COIL
DRIVE
SLED
MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
LOADING
MOTOR
DRIVE 28
12
11
13
14
15
16
17
18
9
10
5
53
52
M902
(SLED)
M901
(SPINDLE)
M903
(LOADING)
SW4
(LIMIT)
SW2
(SELF)
SW1
(DOWN)
SW3
(DISC IN)
X1
16.9344MHz
OPTICAL PICK-UP
(KSS1000E)
I-V
CONV.
CDL
R-CH
CD_STB
CD_A0
CD_SO
CD_SI
CD_CKO
CD RESET
30 74 ZERO DET1
29 75 ZERO DET2
CD_RFOK
CD_INSW
CD_LIMIT
CD_SELFSW
CD_DSW
CD_LM_LOAD
CD_LM_EJECT
TUNER
SECTION
A
23 24
M
M
M
LOUT
ROUT
SI
716 CD_INTQ
INTQ
RFOK
LMUTE
RMUTE
SO
SCK
STB
A0
RST
PD
LD
A
C
B
D
E
F
PD
LD
LD AMP
FOCUS
COIL
TRACKING
COIL
FD+
FD+ FD- TD+ TD- SD+ SD- MD+ MD-
FSC+
FSC-
TRK+
TRK-
SL-
SL+
SP-
SP+
LD-
LD+
LOAD
EJECT
SYSTEM CONTROL
IC303 (1/3)
RF AMP,DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
IC1
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING MOTOR DRIVE
IC2
6
FD-
2
TD+
3
TD-
27
SD+
26
SD-
24
MD+
23
MD-
Signal path
: CD
A3.3V
AU3.3V
D3.3V
DR6V
CD+3.3V
CD+6V
+-
+-
+-
52 53 54 55 56 57 58 59
IC251 (1/3) 62
IC251 (2/3)
17
IC251 (3/3)
35
R-CH is omitted due to same as L-CH
3-2. BLOCK DIAGRAM — CD SECTION —
(Page 20)

2020
CDX-F7000/F7005X/FW700
1ANT
40 TUNER LCH
ELECTRONIC VOLUME
IC401
J601
(ANTENNA)
TUX501
(TUNER UNIT)
CONTROLLED POWER AMP/
MULTIPLE VOLTAGE REGULATOR
IC201
SYSTEM CONTROL
IC303 (2/3)
CNP101
41 TUNER RCH
BATT
42 CD LCH
43 CD RCH
R-CH
4
3
10
VCC
11
TU VDD
15
E2P VDD
13
TU-SCL
14
TU-SDA
6
S-METER
7
TU MUTE
16
E2P SCL
17
E2P SDA
82 VSM
8
MUTE CONDITION 73 TU ATTIN
AU+8V
TU+5V
BU+5V
32 TUNER ATT
34 EEP SCL
33 EEP SIO
L
R
CD-L
R-CH
17
22
OUTSW
OUT RF
21
OUT RR
R-CH
L
R
5
3
FL+
FL-
9
7
RL+
RL-
29
27
SW1
R-CH
SW2
BATT
30
37
REG1
REG2
31
33
REG3
REG4
34
REG5
TU+5V
BATT
14
16
SA IN
SA OUT
15
MUTE
2SDA
AU+8V
BU+5V
CD+3.3V
CD+6V
ILL+B
4SCL
SDA
SCL
16 ACGND
22 STB
25 DIAG
AU+8V
35 VP
15
13
7
10
12
11
16
1
9
2
4
3
5
6
13
12
SCL
SDA
SCL
SDA
SCL
SDA
SCL
SDA
27
IIC SCK
28
IIC SIO
26
VOL ATT
25
ATT
20
BEEP
41
AMP STB
40
AMP DIAG
83
SA IN
23
SA CLK
66
BUS/AUX
18
BU IN
63
TEST IN
12 INFL FL+
FL-
RL+
RL-
FR+
FR-
RR+
RR-
AMP-REM
ANT-REM
ACC
TEST
25
OUT LF
11 INRL
24
OUT LR
MUTE
Q171
REAR
AUDIO OUT
MUTE CONTROL
Q401,402
30
UNI SI
29
UNI SO
31
UNI CKO
64
BUS ON
65
SYS RST
10 B CHK
8DATA OUT
9DATA IN
11 CLK IN
12 BUSON
13 RST
3
5
4
7
6
2
1
3
BATT
6
DATA I/O
4
CLK
1
BUS ON
2
RST
68
ACC IN ACC CHECK
Q102
TU+5V REG
Q501
BATT
BATT
BATT DET
Q101
BUS INTERFACE
IC110
MUTE
Q181
ATT
24
TEL ATT TEL ATT
Q103
14
69
ILL IN ILL
D401
F901
R-CH
L
R
FRONT
AUDIO OUT
R-CH
4
7
PB LCH
PB RCH R-CH
L
R
BUS
AUDIO IN
PJ401
CN401
SUB OUT(MONO)
BUS
CONTROL
IN
D105
CD
SECTION A
TH100
CNP102
8
BATT
ILL CHECK
Q907
GROUND SW
Q408
MUTE
Q470
• Signal Path
• R-CH is omitted due to same as L-CH.
: CD PLAY
: FM
: AM
3-3. BLOCK DIAGRAM — MAIN SECTION —
(Page 19)