Sony XA-CA660X Guide

SONY XR-CA660X (GB,AR) 3-247-838-21 (1)
SONY XR-CA660X (GB,AR) 3-247-838-21 (1)
Sony Corporation © 2003 Printed in Thailand
3-247-838-21 (1)
Equipment used in illustrations (not supplied)
     
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g., seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1and the protection collar 5are
attached to the unit before shipping. Before
mounting the unit, use the release keys 7to
remove the bracket 1and the protection collar
5from the unit. For details, see “Removing
the protection collar and the bracket (4)” on
the reverse side of the sheet.
•Keep the release keys 7for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1carefully to avoid injuring
your fingers.
Note
Before installing, make sure that the catches on
both sides of the bracket 1are bent inwards 2 mm.
If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
1
2
B
12
×4
3
56
×2
Power amplifier
  
CD/MD changer
 CD MD
Front speaker
 
Rear speaker
 
BUS AUDIO IN
BUS CONTROL IN
BUS CONTROL IN
BUS AUDIO IN
A
Installation/Connections

FM/MW/SW
Cassette Car
Stereo
Connection example (2)
Notes (2-B- )
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B- )
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2To the power aerial control lead or power supply
lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there is
no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4To the interface cable of a car telephone
5To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/SW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
6To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to a metal
surface of the car first.
*not supplied
 
AUDIO OUT
REAR
XR-CA660X
7
4
Catch
1
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN AUDIO OUT
REAR
Source selector*
  *
XA-C30
Rotary commander RM-X4S
     RM-X4S
EA+1ARA.p65 12/6/02, 12:54 PM2
Black

SONY XR-CA660X (GB,AR) 3-247-838-21 (1)
SONY XR-CA660X (GB,AR) 3-247-838-21 (1)

•        
  •    ,    
  : •     ,  
    •                 •       
 •         
   
     
•       
        ,
   •  ,      
  
 (1)
•       
•    1   5
 ,      
 7    1 5  ,     ”     ”(4)   •   7 
      
  

  1   

        , 
  1    
  ,        
       
3
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit
shares a common negative (–) lead for the right
and left speakers.
• Do not connect the unit’s speaker cords to each
other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make
sure the speaker and amplifier are connected
correctly.
  (2)
 ( -B-2)
•
       
•         
     ,
”  ” 

( -B-2)
    CD  MD   ,     
XA-C30 
 (3)
1     
       
    
2         
   

•         
     ,   
•      FM/MW/SW
  ,     ”      
” 
3  AMP REMOTE IN   
      
      
4     
5   +     
      

•    ,    
    +         
      
 
•      FM/MW/SW
  ,    
”       ” 
6    +      
        
     
•         
 +       
•      FM/MW/SW 
    ,   
       
       
    ,    

•          

  
    ,     
          
   
•     ,  
•               
•        
       ,
   
•         

(–)  
•        
•                
     
•       ,          
(–)
   
•        

  
 ,         
 “FAILURE”   ,    
      

1
BUS
AUDIO IN AUDIO OUT
AUDIO
OUT
REAR
BUS
AUDIO
IN
BUS
AUDIO IN AUDIO
OUT REAR
BUS
CONTROL IN
REMOTE IN
1
2
4
5
Supplied with XA-C30
  XA-C30
Red

Yellow

6
Black

RCA pin cord (not supplied)
   RCA 
Max. supply current 0.1 A
    
from car aerial
  
Fuse (10 A)
  
AMP REM
ANT REM
Blue/white striped
 
Max. supply current 0.3 A
    
White

Grey

Green
 
Purple

White/black striped
 
Grey/black striped
 
Green/black striped
  
Purple/black striped
 
Source selector
(not supplied)
  
 
XA-C30
Left

Right

Left

Right

3
Supplied with the CD/MD changer
      CD  MD
Blue

Light blue
 
6
* Insert with the cords upwards.
*      
*
ATT
EA+1ARA.p65 12/6/02, 12:54 PM3
Black

SONY XR-CA660X (GB,AR) 3-247-838-21 (1)
SONY XR-CA660X (GB,AR) 3-247-838-21 (1)
to dashboard/centre console
    
Bracket
 
Bracket
 
6ATOYOTA BNISSAN
412
182 mm
53 mm
12
Claws

3
13
Dashboard
  
5
5
7AB
1
2
Fire wall
 
1
Existing parts supplied with your car
    
4
4
5
7
c
Orient the release key
correctly.    

7
cc
1Face the hook
inwards.    
2
c
A
B
max. size
5 ×8 mm     × 
max. size
5 ×8 mm     × 
Existing parts supplied with your car
    
to dashboard/centre console
    
Bracket
 
Bracket
 
max. size
5 ×8 mm
  
 × 
4
max. size
5 ×8 mm
  
× 
4
EA+2ARA.p65 12/6/02, 12:53 PM4
Black

SONY XR-CA660X (GB,AR) 3-247-838-21 (1)
SONY XR-CA660X (GB,AR) 3-247-838-21 (1)
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
Removing the protection collar
and the bracket (4)
Before installing the unit, remove the
protection collar 5and the bracket 1from
the unit.
1Remove the protection collar 5.
1Engage the release keys 7together with
the protection collar 5.
2Pull out the release keys 7to remove the
protection collar 5.
2Remove the bracket 1.
1Insert both release keys 7together
between the unit and the bracket 1
until they click.
2Pull down the bracket 1, then pull up the
unit to separate.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if
necessary (5-2).
• Make sure that the 4 catches on the protection
collar 5are properly engaged in the slots of the
unit (5-3).
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
  
•           •, ,      
  ,    , 
       
•      
  
  
      
    
(4)
   ,   5  
1  
1   51
  7    52   7   52   11
  7    
1     2   1  ,   
  (5)
    

•         
(5-2)
•
         5 
       
(5-3)
    (6)
         
    ,    
  

       , 
4 
    
(7)
   ,  
A-7
   ,   (OFF)  (OPEN)
 ,       ,
  
B-7  A       B
   ,      
  
     
  
ACC   
   ,    
(OFF)        
     ,
RESET 
    ,    
RESET   ,… ,   
How to detach and attach the
front panel (7)
Before installing the unit, detach the front
panel.
7-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
7-B To attach
Place the hole Ain the front panel onto the
spindle Bon the unit as illustrated, then push
the left side in.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After tuning off the ignition, be sure to
press and hold (OFF) on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
EA+2ARA.p65 12/6/02, 12:53 PM5
Black