Sony XDP-MU110 User manual

Make your iPod touch® or iPhone® sound crisp and clear using your factory audio
system with the Sony® Digital Link Sound System.1 The Sony XDP-MU110 uses
internal DSP processing to brighten your front soundstage and control playback from
your device docked on the adjustable dash mounted cradle.
Specications
XDP-MU110 XDP-MU110 Digital Link Sound System
Bullets
• iPod touch®/iPhone® integration for your factory audio system1
• Hide-away DSP processor creates balanced front stage
• Convenient setup to optimize sound output
• Built in 45 watts x 4 channel for interior speakers
• 2V front, rear and sub pre-amp output
• Convenient wireless remote
Amplier Section
Max power output DSP Unit: 45 watts x 4 at 4 ohms
Power Ad Hoc CEA2006
DSP: 17W RMS @ 4 Ohms, 20Hz-20kHz, 1% THD+N
Speaker Impedance 4-8 Ohms
AMP & General Feature
Automatic Level Optimizer Yes
Bass/Treble Bass: +/- 7 dB @ 100HZ, Treble: +/- 7 dB @ 7 kHz
Output Power (4ohm, 1kHz,16V)(W) DSP Unit: 45 watts x 4 at 4 ohms
Pre Out (3) Front, Rear and Sub
Time Alignment Custom Yes (Adjustment)
Time Alignment Preset Yes
Features
iPod touch® and iPhone® integration
Improve the sound of your iPod touch® or iPhone® digital music using your factory audio system.1 Control
playback of internally stored audio content or listen to audio from your wireless audio apps on your device with
the adjustable dash mounted cradle.
DSP processing
Internal DSP processing improves both your factory audio system playback and your iPod touch® or iPhone®
playback.1 The system enables adjustment of time alignment, equalization and crossover points to deliver an
incredible audio experience.
Convenient Setup
Sound is customized to t your ride. The hide-away DSP processor utilizes 3 multi-position switches to adjust 18
dierent DSP parameters.
High-powered Expansion
Whether using the internal 45W x 4 high power amplier for your speakers or the 2 Volt Front, Rear and Sub RCA
pre-amp outputs to feed an external amplier, you can dial in the output for optimum sound.
Wireless Remote Control
The included wireless remote lets you control the basic functions of your XDP-MU110.

1. Works with iPod® touch 3rd-4th generation, iPhone® 3GS and iPhone 4.
© 2011 Sony Electronics Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Sony and is a trademark of Sony. iPod touch and iPhone are trademarks of Apple Inc. All other
trademarks are the property of their respective owners. Features and specications are subject to change without notice. Updated: September 9, 2011
Audio
Preout Impedance 220 ohms
Preout Voltage 2 volt
S/N Ratio Audio Power:
DSP: S/N 80 dBA
Convenience Features
Key Illumination White
General
CEA2006 output power DSP: 17W RMS @ 4 Ohms, 20Hz-20kHz, 1% THD+N
CEA2006 S/N DSP: S/N 80 dBA
Dimensions (WxHxD) (mm) DSP: 8.375 x 1.625 x 6.125 inches
Maximum output power (4ohm, 1kHz, 16V)(W) DSP Unit: 45 watts x 4 at 4 ohms
Mounting dimensions (WxHxD)(mm) DSP: 210.6 x 40 x 156.6
Preout impedance (ohms) 220
Preout output level (V) 2
Inputs and Outputs
12V Trigger Output(s) Power amplier turn on
Audio In High Level input connector
Digital Audio Input(s)
This unit can be connected to the following iPods. Update your iPod to the latest software before you
use it.
iPod Touch 3rd - 4th generation
iPhone 3GS
iPhone 4
If you have any questions or problems concerning your unit that are not covered in the owners
manual, consult your nearest Sony dealer.
RCA Audio Output(s) Front, Rear and Subwoofer RCA pre-amp outputs
Other Features
Card Remote ( ): Option RM-X251
Weights and Measurements
Dimensions (Approx.) DSP: 8.375 x 1.625 x 6.125 inches, 210.6 x 40 x 156.6 mm
Weight (Approx.) DSP: .92 kg (2 lb. 1 oz.)
Supplied Accessories
Supplied Accessories
Parts for installation and connections (1 set)
RM-X251 wireless remote
XDP-MU110 DSP unit
XA-C100IP Cradle