Sony CD Walkman D-EJ011 User manual

PORTABLE CD PLAYER
E Model
SPECIFICATIONS
D-EJ011
Ver. 1.0 2006.12
Model Name Using Similar Mechanism D-EJ010
CD Mechanism Type CDM-3525A
Optical Pick-up Name DAX-25E
9-887-511-01
2006L02-1
© 2006.12
Sony Corporation
Personal Audio Division
Published by SonyTechno Create Corporation
SERVICE MANUAL
System: Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output is the
value measured at a distance of 200 mm from the
objective lens surface on the optical pick-up block
with 7 mm aperture.)
Power requirements
• Two LR6 (size AA) batteries: 1.5 V DC ×2
Dimensions (w/h/d) (without projecting parts and controls)
Approx. 139.8 ×27.9 ×139.8 mm
Mass (excluding accessories)
Approx.188 g
Operating temperature 5°C - 35°C (41°F - 95°F)
Battery life* (approx. hours)
(When the CD player is used on a flat and stable
place.)
Playing time varies depending on how the CD player
is used.
G-PROTECTION G-on G-off
Two Sony alkaline batteries LR6 (SG)
(produced in Japan) 16 11
* Measured value by the standard of JEITA(Japan
Electronics and Information Technology Industries
Association).
• The indicator sections of roughly show the
remaining battery power. One section does not
always indicate one-fourth of the battery power.
Design and specifications are subject to change
without notice.
Supplied accessories
Headphones (1)

2
D-EJ011
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 ˚C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
otherthan thosespecified hereinmay resultin hazardousradiation
exposure.
TABLE OF CONTENTS
1. SERVICING NOTES ................................................ 3
2. GENERAL ................................................................... 3
3. DISASSEMBLY
3-1. Disassembly Flow ........................................................... 4
3-2. Cabinet (Inner) Assy,
Cabinet (Lower) Assy...................................................... 4
3-3. Optical Pick-up (CDM-3525A),
MAIN Board.................................................................... 5
4. ELECTRICAL ADJUSTMENT ............................. 6
5. DIAGRAMS
5-1. Block Diagram ................................................................ 8
5-2. Printed Wiring Board
– Main Board (Side A) – ................................................. 9
5-3. Printed Wiring Board
– Main Board (Side B), Jack Board – ............................. 10
5-4. Schematic Diagram – Main Board (1/2) – ..................... 11
5-5. Schematic Diagram – Main Board (2/2), Jack Board – . 12
5-6. IC Pin Function Description............................................ 15
6. EXPLODEDVIEWS ................................................. 17
7. ELECTRICAL PARTS LIST .................................. 18
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

3
D-EJ011
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
During normal operation of the equipment, emission of the laser
diode is prohibited unless the upper lid is closed while turning ON
the S811. (push switch type)
The following checking method for the laser diode is operable.
Fig. 1 Method to push the S811
SECTION 2
GENERAL This section is extracted from
instruction manual.
LOCATINGTHE CONTROLS
•Method:
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. With a disc not set, turn on the S811 with a screwdriver having
a thin tip as shown in Fig.1.
3. Press the u button.
4. Observing the objective lens, check that the laser diode emits
light.
When the laser diode does not emit light, automatic power
control circuit or optical pick-up is faulty.
In this operation, the objective lens will move up and down 2
times along with inward motion for the focus search.
S811
Remaining battery power
Sound mode
Track number
Playing time
Play mode
Bookmark
* The button has a tactile dot
.
^*(play/pause)
DC IN 4.5 V
2(headphones) jack
p(stop)
HOLD (rear)
VOL –/+*
Headphones
SOUND/AVLS
=+/
P MODE/
OPEN
Display

4
D-EJ011 SECTION 3
DISASSEMBLY
•This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
3-2. CABINET (INNER) ASSY, CABINET (LOWER) ASSY
Note: Follow the disassembly procedure in the numerical order given.
3-2. CABINET (INNER) ASSY,
CABINET (LOWER) ASSY
(Page 4)
3-3. OPTICAL PICK-UP (CDM-3525A),
MAIN BOARD
(Page 5)
SET
4 two screws
cabinet (inner) ass
y
cabinet (lower) assy
3 five screws
1
2
5 two claws
6 two claws

5
D-EJ011
3-3. OPTICAL PICK-UP (CDM-3525A), MAIN BOARD
MAIN Board (side A)
To/From
Optical devic
e
CDM-3525A
BLK
RED
ORG
GRY
4 MAIN board
cabinet (lower) assy
3 optical pick-up CDM-3525A
1 CN501
2 Unsolder four lead wires

6
D-EJ011 SECTION 4
ELECTRICAL ADJUSTMENTS
The CD section adjustments are done automatically in this set.
Adjusting Procedure:
1. Perform check in the order given.
2. UseYEDS-18 disc (Part No: 3-702-101-01) unless otherwise
indicated.
3. Power supply voltage requirement :DC4.5 V in DC IN jack.
(J401)
VOLUME button : Minimum
HOLD switch :OFF
Focus bias Check
Condition:
• Hold the set in horizontal state.
Connection:
Procedure:
1. Make a solder bridge to short SL801 (OPEN) on the MAIN
board side B.
2. Connect the oscilloscope to the test point TP604 (EQOUT)
and TP406 (M-GND) on the MAIN board side B.
3. Set a disc. (YEDS-18)
4. Press the ubutton.
5. Check the oscilloscope waveform is as shown below.
A good eye pattern means that the diamond shape ( ) in the
center of the waveform can be clearly distinguished.
RF Signal referenceWaveform (Eye Pattern)
To watch the eye pattern, set the oscilloscope to AC range and
increase the vertical sensitivity of the oscilloscope for easy
watch-ing.
6. Stop revolving of the disc motor by pressing the xbutton.
7. SL801 is opened by taking the solder bridge.
RF level
1.3
± 0.2 Vp-p
VOLT/DIV : 500 mV (With the 10 : 1 probe in use
)
TIME/DIV : 500ns
(SIDE B)
MAIN BOARD
1
25
26 50
X601
S811
(OPEN)
SL801
(OPEN)
i
J301
E
C629
TP604
EQ OUT
C627
C110
R107
R207
R101
C803
R305
L201R211 R111
C612
R602
R617
C625
R622
R625
R626
R618
Q602
L301
L101
IC602
oscilloscope
(AC range)
+
–
TP604
(EQOUT)
SL801
(OPEN)

77
D-EJ011
D-EJ011
Note on Printed Wiring Boards.
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•a: Through hole.
•f: internal component
•: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
•Note for PrintedWiring Boards and Schematic Diagrams
Note on Schematic Diagrams.
•All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
• f: internal tolerance.
•C: panel designation.
•A: B+ Line.
•H: adjustment for repair.
•Power voltage is dc 3 V and fed with regulated dc power
supply from battery terminal.
•Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD PLAY
•Voltagesare taken withaVOM (Input impedance10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
•Circled numbers refer to waveforms.
•Signal path.
J: CD PLAY
Caution:
Pattern face side: Partson the patternface side seenfrom
(Side B) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Side A) the parts face are indicated.
•Indication of transistor.
Note: The components identified by mark 0or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
SECTION 5
DIAGRAMS
C
BThese are omitted. E
Q
D
GThese are omitted. S
Q
•Waverforms
1IC601 yj XO
2 V/DIV, 50 ns/DIV
59.5 ns 4.5 Vp-p
2IC801 yd XOUT4M
2 V/DIV, 0.1 µ s/DIV
244 ns 3.5 Vp-p

88
D-EJ011
D-EJ011
5-1. BLOCK DIAGRAM
: CD PLAY
• Signal Path
3
80 79
3
5
65
1
772
2
17
4
7
8
15 16 18 19
6463
51
6667
2423505349474839
62
272625242322
3
57
6
9
18
DRIVER
DRIVER
DRIVER
17
19
20
23
22
11
DIGITAL
FILTER
SERVO
SIGNAL
GEN.
RF
SIGNAL
GEN.
OP IC
DIGITAL SERVO
SIGNAL GEN.
PD
LD
FDOUT TDOUT SDOUT CLVOUT
TRK
FOCUS
20
CLK88
CLK
TRK
SLED
CLV
XO XI SUBSYQ MCK DIN/DOUT R/W RESETX BUSY
CLOCK
OSC
DAC
31
36
21
35
SWITCHING
Q404
SWITCHING
Q403
17 16 15
47-62
19-24,27-32
2,3,5,6,8,9,11,12,39,
40,42,43,45,46,48,49
43-32
MEMORY
CONTROLLER
41 40
1-18 77-80 29-32,34
70
LCD801
LIQUID
CRYSTAL
DISPLAY
KEY MATRIX
XIN4M
SUBSYQ
21
CLK
MCK
DIN OUT
RW
EE_SCL
EE_SDA/REM_SDA
XXRESET
BUSY
DQM
MUTE2
XRESET
SEG0 I SEG17 COM1 I COM4
KEYSCAN1 I KEYSCAN5
OPEN/CLOSE
HOLD
REGB
65
DC IN
30 DCIN
IC801
SYSTEM
CONTROL
L401
D403
F402
F401
DDC
LG
PVCC
+VBAT
VG
DDC
L402
L403
VG
38 VSYS
37 SW
X601
16.9344MHz
RDACO
LDACO
Q602
OUT1
OUT2
IN1
IN2
SDA SCL
7
WP
8
VCC
IC301
HEADPHONE AMP
IC802
EEPROM
IC401 (2/2)
DC/DC CONVERTER
BD
AC
DDC
E
FO+
FO-
TRK-
TRK+
SLED+
SLED-
F
SDIN
VBIAS
AMP
10 FOCUS
AMP
8SLED
AMP
7CLV
CLK
TRK
FOCUS
VREF
SLED
CLV
CLK
AMP
RESET
74
2XP.OFF
OFF
76
4
MUTE34
75
5MUTE1
MUTE1
43
1K_PLAY
WP
IC401 (1/2)
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE MOTOR DRIVE
IC602 SDRAM(16M)
RAS CAS WE
RASX
A00-A11
DQ0-15
RFI
EQO
CASX
WEX
DQ0-15 A0-11
44 45 46
14 36
LDQM UDQM
35 34
CLK CKE
RCLK
C2FX
YFLAG
RCKE
28 29
IC601
RF AMP, SERVO,
DIGITAL SIGNAL PROCESSOR,
SDRAM CONTROLLER,
D/A CONVERTER
J401
DC IN 4.5V
!
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION LR6)
2PCS. 3V
J301
i
(SLED)
FOCUS
COIL
(SPINDLE)
M
TRACKING
COIL
F+
F-
T+
T-
SLED+
SLED-
DRIVER
25
24
SPID+
SPIN-
M
SPINDLE+
SPINDLE-
OPTICAL
DEVICE
(CDM-3525A)
VCC
+
+
A
B
C
E
F
LD
PD
VC
LD
DRIVER
Q601
DDC
S811
(OPEN)
S812
HOLD
OFF ON
S807
APC
10
9
D803 46
K_STOP
S801
S802
|
S805
S808,
S809
+B SWITCH
Q401
DC IN DETECT
Q402
L404
L405

99
D-EJ011
D-EJ011
5-2. PRINTED WIRING BOARD – MAIN BOARD (SIDE A) – :Uses unleaded solder.
• Semiconductor
Location
Ref. No. Location
D401 E-6
D403 D-6
D803 D-5
IC301 A-2
IC601 B-4
IC802 E-4
Q401 D-6
Q402 E-6
Q403 E-7
IC301
IC601
14
85
120
40
60
21
41
61
80
14 85
E
E
+– –+
(SLED)
M
(SPINDLE)
M
OPTICAL DEVICE
(CDM-3525A)
(1/2)
GRY
ORG
BLK
RED
C210
R201
R205
R206 R106
R104
R204
R620
R601
R608
C613
C614
C615
R615
R609
R610
C609
C611
C604
R606
R103
R203
R616
R105
R304
R619
C108
C102
C618
R607
C605 C626
R815
R833
R834 R839 R818
R817
C809
C806
C808
D803
R404
D403
R810
L406
L407
CN408
CN403
CN407
CN404
SLED–
SLED+
SPINDLE–
SPINDLE+
C405
R407
C413
R406 R405
R403
D401
F402
L404
L405
C807
R410
R807
R806
C805
R840
R841
R832
Q401
Q402
Q403
C802
R804
R844
R805
R843
IC802
R614
C606
R613
L801
C202
C201
C624
C208
C306
C303
C630
C620
C101
11
(11)
1-871-743-
(SIDE A)BOARDMAIN
23 4 5 6 7
A
1
B
C
D
E
F
8

1010
D-EJ011
D-EJ011
5-3. PRINTEDWIRING BOARD – MAIN BOARD (SIDE B) –:Uses unleaded solder.
• Semiconductor
Location
Ref. No. Location
D404 E-1
IC401 D-3
IC602 B-6
IC801 E-4
Q404 E-2
Q601 C-5
Q602 A-5
1
20
21 40
120
60
80
40
21
61 41
1
22
BP VL
1
25
26 50
DC IN 4.5V
J401
S803
.
S802
>
S807
x
S801
u
LCD801
LIQUID CRYSTAL
DISPLAY
S812
HOLD
.
1
2
15
16
OPTICAL DEVICE
(CDM-3525A)
(2/2)
X601
S811
(OPEN)
SL801
(OPEN)
i
J301
S804
VOL–
S808
SOUND/
AVLS
S805
VOL+
S809
P MODE/
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION LR6)
2PCS. 3V
CN401
CN402
OFF
t
ON
E
E
11
(11)
1-871-743-
D404
Q404
C417
C406
R821
C416
C401
C410
C804
C412
C403
C404
L401
C411
C409
F401
CB414
IC401
IC801
SL803
R828 R831 R830
CN801
C420
C408
R414
R415
R402
R416 R418
R419
R417
R811
C623 C628
C610
C602
C607
C105
C305
C205
C204
C104
C304
C601
C603
CN501
C629
TP604
EQ OUT
C627
C110
R107
R207
R101
C803
R305
L201R211 R111
C612
R603
R602
R617
C625
R622
R625
R626
R618
Q602
R604
Q601
L301
L101
IC602
R812
R823
R624
C619
R829
C811
R401
L403
C419
L402
(SIDE B)MAIN BOARD
23 4 5 6 7 8
1
B
A
C
D
E
F

1111
D-EJ011
D-EJ011
5-4. SCHEMATIC DIAGRAM – MAIN BOARD (1/2) – • See page 7 forWaveforms. • See page 13, 14 for IC Block Diagrams.
DQ00
DQ01
DQ02
DQ03
DQ04
DQ05
DQ06
DQ07
DQ08
DQ09
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
A00
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
D401
D403
IC301
IC601
IC602
Q601
LD DRIVER
501
L406
47uH
47uH
L407
C410
C411
C412
C403
L401 330uH
CB414
R416
R417
R418
R419
R608
R601
R620
R607
C613
R609
R610
C614
C615
C605
C609
C606
R615
R606
R613
R614
C610
C611
C618
X601
C620
C629
2.2 C625
C630
R619
R622
R618
R626
R203
C101 C201 C102 C202
C406
J301
R111
R211
C104
R101
R201
C110
C210
C304
C306
C627
C612
R811
C204
R617
L801
0H
R406 C413
C626
R305
C603
R603
C604
R602
C623
R604
R105
10k
R207
1k
R107
1k
R106
22k
R206
22k
R205
10k
C105 C205
R304
Q602
Q402
Q401
R410
C607
C602
C601
CN403
CN404
CN407
CN408
IC401
R403
C408
C409
C404
R405
C305
C628
R616
C624
L301
0H
0H
L201
0H
L101
C108
C208
R407
C303
MA8062
MA2YD2300LSO
BH3544F
BU9352KV
2SA1235TP-1EF
16P
0.1
470p
1
0.1
0.022
22k
100k
47k
22k
47k
47k
47k
47k
0.01
1k
1k
0.01
2200p
0.1
2200p
0.1
68k
220k
68k
470
4.7 50V
0.22
470p
16.9344MHz
0.1
2.2
1000p
100k
220
1M
10k
R625
10k
220
R103
220
R204
220
R104
220
4700p 4700p 2200p 2200p
0.1
10
10
220
6.3V
10
10
1000p
1000p
100
16V
0.1
0.1
0.1
100k
220
6.3V
100
10k 0.022
0.01
220k
0.01
4.7
0.1
2.2
470
6.3V
100k
4.7
50V 4.7
50V
1M
RT1N140C-TR1
BUFFER
XP6215
DC IN DETECT
2SB1132-T100-Q
+B SWITCH
2.2
47
6.3V
47
6.3V
47
6.3V
BH6575FV-E2
1k
100 16V
10
35V
10
35V
12k
47
6.3V
10
35V
0H
0.1
470p
470p
27k
1
GND
BUS
VCC
PVCC
GND
B+
D GND
A01
A02
A03
A10
A11
A00
DQ00
DQ01
DQ02
DQ03
DQ04
DQ05
DQ06
DQ07
WE
CAS
RAS CKE
CLK
DQ08
DQ09
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ08
DQ09
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ00
DQ01
DQ02
DQ03
DQ04
DQ05
DQ06
DQ07
A00
A01
A02
WE
CAS
RAS
A03
A04
A05
A06
A07
A08
A09
A10
A11
CLK
CKE
1
2
3
4
5
6
7
8
11
13
14
15
16
19
20
A04
A05
A06
A07
A08
A09
3
PVCC
SLED-
SLED+
SPIND-
SPIND+
DPG2
SPRT
SOFT
CT
DCIN
REGB
REGO
PRGND
PGND
LG
VG
SW
VSYS
EI
EO
TRK+
TRK-
FO+
FO-
FIL4
FIL3
FIL2
FIL1
VREF
FOCUS
TRK
SLED
CLV
RESET
MUTE1
MUTE34
CLK
OFF
WP
VSS
DQ15
DQ14
VSSQ
DQ13
DQ12
VCCQ
DQ11
DQ10
VSSQ
DQ9
DQ8
VCCQ
NC
UDQM
CLK
CKE
NC
A9
A8
A7
A6
A5
A4
VSS
VCC
DQ1
VSSQ
DQ2
DQ3
VCCQ
DQ4
DQ5
VSSQ
DQ6
DQ7
VCCQ
LDQM
XWE
CAS
RAS
XCS
A11
A10
A0
A1
A2
A3
VCC
OUT1
XMUTE
IN1
GND
IN2
BIAS
OUT2
VCC
CLK
SUBSYQ
MCK
DIN/DOUT
R/W
BUSY
RCLK
RCKE
WEX
CASX
RASX
CLK88
CLVOUT
SDOUT
SDIN
TDOUT
FDOUT
FCO
PCO
ASY
LD
PD
F
E
BD GAIN
AC GAIN
VBIAS
BD
AC
AVDD1
EQO
ANA MONI1
ANA MONI0
TEST
AD MONI1
AD MONI0
AGND2
RDACO
VCDAC
LDACO
AVDD2
DGND
XO
XI
DVDD
YFLAG
C2FX
16M SDRAM
C
E
A
B
F
VCC
VC
GND
GND
PD
LD
NC
F+
T+
T-
F-
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE MOTOR DRIVE,
DC/DC CONVERTER
DPG1
RESETX
RFI
AGND1 SDRAM CONTROLLER ,D/A CONVERTER
RF AMP,SERVO,DIGITAL SIGNALPROCESSOR,
HEADPHONE AMP
DQ0
M121616A-7T(J)
(2/2)
(Page 12)
BOARD
MAIN
IC B/D
IC B/D
IC B/D

1212
D-EJ011
D-EJ011
5-5. SCHEMATIC DIAGRAM – MAIN BOARD (2/2) – • See page 7 forWaveforms. • See page 15 for IC Pin Function Description.
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG0
COM1
COM2
COM3
COM4
D404
D803
IC801
IC802
L405
L404
L402
165uH
C416
C417
R414
R415 C419
C420
L403
10uH
C405
R404
S801
S807
S802
S803
S805 S804
S808
S809
S812
SL801
R624
R823
R829
C619
R812
R828
R830
R831
R832
R833
R834
R839
C805
R804
CN801
SL803
R818
R805
C806
R806
R815
C802
R810
1M C804
R841
R821
C811
C809
C807
1
Q403
Q404
F401
CN401
CN402
R844
R843
C808
F402
S811
R840
R402
R401
C401
J401
R817
UDZS-TE17-12B
1SS355TE-17
BU1377KS2
S24CS02AFJ-TB-G
0H
0H
47p
0.1
10
1k 220
6.3V
220
6.3V
1000p
100
1k
100k
100k 0.1
100k
1k
1k
1k
1k
1k
1k
100k
0.1
0
22P
100k
VARISTOR
0.1
47k
R807
47k
10k
0.01
VARISTOR
100k
100k
0.1
0.1
2SD2652T106
SWITCHING
2SD2652T106
SWITCHING
2A
32V
10k
10k
1
2A
32V
(OPEN)
(OPEN)
100k
22k
100k
1
10k
BUS
VCC
GND
PVCC
B+
D GND
COM1
COM2
COM3
COM4
SEG01
SEG02
SEG03
SEG04
SEG05
SEG06
SEG07
SEG08
SEG09
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17 SEG00
SEG17
SEG16
SEG15
SEG14
SEG13
SEG12
SEG11
SEG10
SEG09
SEG08
SEG07
SEG06
SEG05
SEG04
SEG03
SEG02
SEG01
COM4
COM3
COM2
SEG00
COM1
2
11
3
4
5
6
7
20
15
13
1
16
8
14
19
DC IN 4.5V
DRY BATTERY
SIZE"AA"
2PCS. 3V
(IEC DESIGNATION R6)
HOLD
ON
OFF
SDA
SCL
WP
VCC
GND
A2
A1
A0
XOUT75
XIN75
TEST0
XRESET
XHP MUTE
TU CTL
CD CTL
XXRESET
VDD
DQM
BUSY
RW
MCK
DIN OUT
K STOP
BEEP
K TUNER
K PLAY
INNER
OPEN/CLOSE
SEL CHG
SEL CEX
CHARGE CTL
XLINEOUT MUTE
EE SCL
PLL CE
PLL CLK
PLL DATA
EE SDA/REM SDA
KEYSCAN6
KEYSCAN5
KEYSCAN4
KEYSCAN1
KEYSCAN2
GND
KEYSCAN3
PLL RST
ST DET
XLINE DET
SUBSYQ
HOLD
MMUE2
MMUE1
XP.OFF
TEST1
SEL DRAM
SEL OPTION
WREM
TEST MODE
KEY1
BATT-
BATT+
DC IN
VDD
XOUT4M
XIN4M
GND
1
5
10
15
20
22
LIQUID
CRYSTAL
DISPLAY
SYSTEM CONTROL
MO/ST
EEPROM
BOARD
MAIN
(1/2)
(Page 11)

13
D-EJ011
•IC Block Diagrams
IC301 BH3544F-FE2
+
67 58
+
2
1 3 4
OUT 1
XMUTE
MUTE
IN 1
GND
VCC OUT 2 BIAS IN 2
BIAS
TSD 6dB
6dB
90k
90k
IC401 BH6575FV-E2
EO
SYSTEM
ON OSC
SYSTEM
OFF
CLK
30k
30k
DC/DC
CONVERTER
–
+
– +
–
+
VG
CONV
VSYS REG
PRE-DR
VSYS
DETECT
OFF 2
MUTE34 4
CLK 3
MUTE1 5
RESET 6
CLV 7
SLED
TRK 9
VREF 11
FIL1 12
FIL2 13 FIL3 14
DPG1 16
TRK– TRK+
19 20
FIL4 15
WP 140
SPIND– SLED+ SLED– PVCC
24 23 22 21
SPIND+
25
SPRT
27
DPG2
26
SOFT
28
DCIN
30
CT
29
REGO
32
REGB
31
PRGND
33
PGND
34
VG
36
LG
35
VSYS
38
SW
37
EI
39
MUTE34
–
–
+
RESET
MUTE1
– +
8
30k
– +
–
+
–
+
–
+
30k
– +
FOCUS 10
PRE-DR
PRE-DR PRE-DR
FO+ 18
FO– 17

14
D-EJ011
IC601 BU9352KV
1
AVDD1
2
AC
3
BD
4
VBIAS
5
AC_GAIN
6
BD_GAIN
7
E
8
F
9
PD
10
LD
11
ASY
12
PCO
13
FCO
14
AGND1
15
FDOUT
16
TDOUT
17
SDIN
18
SDOUT
19
CLVOUT
20
CLK88
CLK
SUBSYQ
MCK
DIN/DOUT
R/W
RESETX
BUSY
RCLK
RCKE
A13
A12
A11
A10
A03
80 79 78 77 76 75 74 73 72 71 70 69
54
DQ00
53
DQ01
52
DQ02
51
DQ03
49
DQ05
DQ06
DQ07
46
WEX
45
CASX
44
RASX
A00
A01
A02
EQO RFI
ANA_MONI1
ANA_MONI0 TEST AD_MONI1 AD_MONI0 AGND2 RDACO
VCDAC LDACO AVDD2 DGND XO
68 67 66 65 64 63
XI DVDD YFLAG C2FX DQ08 DQ09
62 61
21 22 23 24 25 26 27 28 29 30 31 32 33
A09
A08
A07
A06
A05
A04
34 35 36 37 38 39 40
43
42
41
47
48
50
DQ04
60
DQ10
59
DQ11
58
DQ12
57
DQ13
55
DQ15
56
DQ14
ANTI-SHOCK
MEMORY
CONTROLLER
DIGITAL
SIGNAL
PROCESSOR
DIGITAL
SERVO
FILTER
DIGITAL SERVO SIGNAL PROCESSOR
COMMAND INTERFACE
x8 OVER SAMPLING
DIGITAL FILTER
16K SRAM
SERVO SIGNAL GENERAL
RF SIGNAL GENERAL
APC
1 BIT DAC
PLL

15
D-EJ011
5-6. IC PIN FUNCTION DESCRIPTION
Pin No. Pin name I/O Description
• IC801 BU1377KS2 (SYSTEM CONTROLLER)
1 to 18 SEG0 to SEG17 O LCD segment output
19 SEL_CHG I Not used (fixed at “L”)
20 SEL_CEX I Destination select (fixed at “L”)
21 CHARGE_CTL O Not used (OPEN)
22 XLINEOUT_MUTE O LINE OUT muting output (OPEN)
23 EE_SDA/REM_SDA I/O EEPROM data
24 EE_SCL O EEPROM clock
25 PLL_CE O Not used (OPEN)
26 PLL_CLK O Not used (OPEN)
27 PLL_DATA O Not used (OPEN)
28 KEYSCAN6 O Not used (OPEN)
29 KEYSCAN5 O Key matrix detect output
30 KEYSCAN4 O Key matrix detect output
31 KEYSCAN1 I Key matrix detect input
32 KEYSCAN2 I Key matrix detect input
33 GND – Ground terminal
34 KEYSCAN3 I Key matrix detect input
35 PLL_RST O Not used (OPEN)
36 ST_DET O Not used (OPEN)
37 MO/ST O Not used (OPEN)
38 XLINE_DET I/O LINE OUT sensing status detection input (OPEN)
39 SUBSYQ I Sub code sync interuption input
40 HOLD I HOLD switch status detection input
41 OPEN/CLOSE I OPEN switch status detection input
42 INNER O Not used (OPEN)
43 K_PLAY I PLAY KEY input
44 K_TUNER O Not used (OPEN)
45 BEEP O Not used (OPEN)
46 K_STOP I STOP KEY input
47 DIN OUT I/O Command output , DSP status input, subcode Q input
48 MCK O Serial interface clock output
49 RW O DSP’s serial interface Read/Write signal output
50 BUSY I DSP’s auto sequencer status
51 DQM O SDRAM initialize output
52 VDD – Power supply for CPU and I/O
53 XXRESET O System reset output
54 CD_CTL O Not used (OPEN)
55 TU_CTL O Not used (OPEN)
56 XHP_MUTE O Headphone IC mute ON/OFF control output
57 XRESET I Micon reset terminal
58 TEST0 I Connect to GND
59 XIN75 I Not used (fixed at “L”)
60 XOUT75 O Not used (OPEN)
61 GND – Ground terminal
62 XIN4M I 4MHz clock input
63 XOUT4M O 4MHz clock output (OPEN)

16
D-EJ011
Pin No. Pin name I/O Description
64 VDD – Power supply for CPU and I/O
65 DC_IN I DC IN voltage monitoring input
66 BATT+ I Batt+ terminal voltage monitoring input
67 BATT– I Connect to GND
68 KEY1 I Connect to GND
69 TEST MODE I Test mode terminal
70 WREM I Wired remotecontroler key detection input. Not used (fixed at “H”)
71 SEL_OPTION I Connect to GND
72 SEL_DRAM I Connect to GND
73 TEST1 I Connect to GND
74 XP_OFF O Power OFF contorol output
75 MMUTE1 O Spindle motor drive mute output
76 MMUTE2 O Focus/Tracking drive mute output
77 COM1 O LCD common output
78 COM2 O LCD common output
79 COM3 O LCD common output
80 COM4 O LCD common output

17
D-EJ011
SECTION 6
EXPLODED VIEWS
NOTE:
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•The mechanical parts with no reference
numberintheexplodedviewsarenotsupplied.
•Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
R R
Parts of Color Cabinet’s Color
•Accessories are given in the last of the
electrical parts list.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
1X-2176-178-1 CABINET (LOWER) ASSY (S) (SILVER)
1X-2176-179-1 CABINET (LOWER) ASSY (B) (BLACK) (E)
22-887-110-01 TERMINAL (RELAY), BATTERY
3 2-887-109-01 TERMINAL (-), BATTERY
42-887-108-01 TERMINAL (+), BATTERY
5A-1220-717-A MAIN BOARD, COMPLETE
63-245-331-02 INSULATOR
1
2
3
4
5
6
6
789
10
11
LCD801
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
07A-1112-193-A OPTICAL PICK-UP CDM-3525A
83-254-070-11 SCREW
92-887-113-01 SPRING (LID)
10 2-887-103-01 LID, BATTERY CASE
11 X-2176-174-1 CABINET (INNER) ASSY (SILVER)
11 X-2176-175-1 CABINET (INNER) ASSY (BLACK) (E)
LCD801 1-805-860-11 DISPLAY PANEL, LIQUID CRYSTAL

18
D-EJ011 SECTION 7
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:
•Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
•-XX and -X mean standardized parts, so they
may have some difference from the original
one.
•RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
•Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•SEMICONDUCTORS
In each case, u: µ, for example:
uA... : µA... uPA... : µPA...
uPB... : µPB... uPC... : µPC...
uPD... : µPD...
•CAPACITORS
uF: µF
•COILS
uH: µH
When indicating parts by reference
number, please include the board.
Thecomponents identified by mark
0or dotted line with mark 0are
critical for safety.
Replace only with part number
specified.
A-1220-717-A MAIN BOARD, COMPLETE
********************
2-887-108-01 TERMINAL (+), BATTERY
2-887-109-01 TERMINAL (–), BATTERY
< CAPACITOR >
C101 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V
C102 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C104 1-124-635-00 ELECT 220uF 20% 6.3V
C105 1-126-794-11 ELECT 4.7uF 20% 50V
C108 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C110 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C201 1-100-581-81 CERAMIC CHIP 0.0047uF 10% 50V
C202 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C204 1-124-635-00 ELECT 220uF 20% 6.3V
C205 1-126-794-11 ELECT 4.7uF 20% 50V
C208 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C210 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C303 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C304 1-126-382-11 ELECT 100uF 20% 16V
C305 1-126-513-11 ELECT 47uF 20% 6.3V
C306 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C401 1-100-352-91 CERAMIC CHIP 1uF 20% 16V
C403 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C404 1-126-791-11 ELECT 10uF 20% 35V
C405 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C406 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C408 1-126-382-11 ELECT 100uF 20% 16V
C409 1-126-791-11 ELECT 10uF 20% 35V
C410 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C411 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C412 1-115-156-11 CERAMIC CHIP 1uF 10V
C413 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C416 1-164-866-11 CERAMIC CHIP 47PF 5% 50V
C417 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C419 1-124-635-00 ELECT 220uF 20% 6.3V
C420 1-124-635-00 ELECT 220uF 20% 6.3V
C601 1-126-513-11 ELECT 47uF 20% 6.3V
C602 1-126-513-11 ELECT 47uF 20% 6.3V
C603 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C604 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C605 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C606 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C607 1-126-513-11 ELECT 47uF 20% 6.3V
C609 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C610 1-126-794-11 ELECT 4.7uF 20% 50V
C611 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V
C612 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C613 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C614 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C615 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50V
C618 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C619 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C620 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C623 1-119-941-41 ELECT 470uF 20% 6.3V
C624 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C625 1-165-884-91 CERAMIC CHIP 2.2uF 10% 6.3V
C626 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C627 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C628 1-126-791-11 ELECT 10uF 20% 35V
C629 1-165-884-91 CERAMIC CHIP 2.2uF 10% 6.3V
C630 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C802 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V
C803 1-165-128-11 CERAMIC CHIP 0.22uF 16V
C804 1-802-068-21 VARISTOR, CHIP (1608)
C805 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C806 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C807 1-115-156-11 CERAMIC CHIP 1uF 10V
C808 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C809 1-107-820-11 CERAMIC CHIP 0.1uF 16V
C811 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
CB414 1-112-557-11 CERAMIC CHIP 0.022uF 20% 16V
< CONNECTOR >
CN501 1-774-975-51 CONNECTOR, FFC/FPC 16P
< DIODE >
D401 8-719-422-58 DIODE MA8062
D403 8-719-085-43 DIODE MA2YD2300LS0
D404 8-719-083-82 DIODE UDZS-TE17-12B
D803 8-719-404-50 DIODE MA111-TX
< FUSE >
0F401 1-576-415-21 FUSE 2A 32V
0F402 1-576-415-21 FUSE 2A 32V
MAIN
•Abbreviation
KR : korea model

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
19
D-EJ011
< IC >
IC301 8-759-588-61 IC BH3544F-FE2
IC401 6-704-047-01 IC BH6575FV-E2
IC601 6-708-130-01 IC BU9352KV
IC602 6-709-459-01 IC M12L16161A-7T (J)
IC801 6-806-316-01 IC BU1377KS2
IC802 6-710-820-01 IC S-24CS02AFJ-TB-G
< JACK >
J301 1-820-259-11 JACK, HEADPHONE (i)
J401 1-819-364-11 JACK, DC (POLARITY UNIFIED TYPE)
(DC IN 4.5V)
< COIL >
L101 1-400-981-21 INDUCTOR (EMI FERRITE)
L201 1-400-981-21 INDUCTOR (EMI FERRITE)
L301 1-400-970-21 INDUCTOR (EMI FERRITE)
L401 1-457-095-11 INDUCTOR 330uH
L402 1-457-096-21 INDUCTOR 165uH
L403 1-400-945-11 INDUCTOR 10uH
*L404 1-400-974-21 INDUCTOR (EMI FERRITE)
*L405 1-400-974-21 INDUCTOR (EMI FERRITE)
L406 1-400-145-21 INDUCTOR 47uH
L407 1-400-145-21 INDUCTOR 47uH
L801 1-400-981-21 INDUCTOR (EMI FERRITE)
< LIQUID CRYSTAL DISPLAY PANEL>
LCD801 1-805-860-11 DISPLAY PANEL, LIQUID CRYSTAL
< TRANSISTOR >
Q401 8-729-106-60 TRANSISTOR 2SB1115A-YQ
Q402 8-729-428-51 TRANSISTOR XP6215
Q403 6-550-364-01 TRANSISTOR 2SD2652T106
Q404 6-550-364-01 TRANSISTOR 2SD2652T106
Q601 8-729-600-22 TRANSISTOR 2SA1235-F
Q602 8-729-027-44 TRANSISTOR DTC114TKA-T146
< RESISTOR >
R101 1-216-797-11 METAL CHIP 10 5% 1/10W
R103 1-216-813-11 METAL CHIP 220 5% 1/10W
R104 1-216-813-11 METAL CHIP 220 5% 1/10W
R105 1-216-833-11 METAL CHIP 10K 5% 1/10W
R106 1-216-837-11 METAL CHIP 22K 5% 1/10W
R107 1-216-821-11 METAL CHIP 1K 5% 1/10W
R111 1-216-797-11 METAL CHIP 10 5% 1/10W
R201 1-216-797-11 METAL CHIP 10 5% 1/10W
R203 1-216-813-11 METAL CHIP 220 5% 1/10W
R204 1-216-813-11 METAL CHIP 220 5% 1/10W
R205 1-216-833-11 METAL CHIP 10K 5% 1/10W
R206 1-216-837-11 METAL CHIP 22K 5% 1/10W
R207 1-216-821-11 METAL CHIP 1K 5% 1/10W
R211 1-216-797-11 METAL CHIP 10 5% 1/10W
R304 1-216-857-11 METAL CHIP 1M 5% 1/10W
R305 1-216-849-11 METAL CHIP 220K 5% 1/10W
R401 1-216-845-11 METAL CHIP 100K 5% 1/10W
R402 1-216-837-11 METAL CHIP 22K 5% 1/10W
R403 1-216-821-11 METAL CHIP 1K 5% 1/10W
R404 1-216-809-11 METAL CHIP 100 5% 1/10W
R405 1-218-873-11 METAL CHIP 12K 0.5% 1/10W
R406 1-216-833-11 METAL CHIP 10K 5% 1/10W
R407 1-218-881-11 METAL CHIP 27K 0.5% 1/10W
R410 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R414 1-216-797-11 METAL CHIP 10 5% 1/10W
R415 1-216-821-11 METAL CHIP 1K 5% 1/10W
R416 1-216-837-11 METAL CHIP 22K 5% 1/10W
R417 1-216-845-11 METAL CHIP 100K 5% 1/10W
R418 1-216-841-11 METAL CHIP 47K 5% 1/10W
R419 1-216-837-11 METAL CHIP 22K 5% 1/10W
R601 1-216-841-11 METAL CHIP 47K 5% 1/10W
R602 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R603 1-216-793-11 METAL CHIP 4.7 5% 1/10W
R604 1-216-845-11 METAL CHIP 100K 5% 1/10W
R606 1-216-849-11 METAL CHIP 220K 5% 1/10W
R607 1-216-841-11 METAL CHIP 47K 5% 1/10W
R608 1-216-841-11 METAL CHIP 47K 5% 1/10W
R609 1-216-821-11 METAL CHIP 1K 5% 1/10W
R610 1-216-821-11 METAL CHIP 1K 5% 1/10W
R613 1-216-843-11 METAL CHIP 68K 5% 1/10W
R614 1-216-817-11 METAL CHIP 470 5% 1/10W
R615 1-216-843-11 METAL CHIP 68K 5% 1/10W
R616 1-400-981-21 INDUCTOR (EMI FERRITE)
R617 1-216-809-11 METAL CHIP 100 5% 1/10W
R618 1-216-857-11 METAL CHIP 1M 5% 1/10W
R619 1-216-845-11 METAL CHIP 100K 5% 1/10W
R620 1-216-841-11 METAL CHIP 47K 5% 1/10W
R622 1-216-813-11 METAL CHIP 220 5% 1/10W
R624 1-216-845-11 METAL CHIP 100K 5% 1/10W
R625 1-216-833-11 METAL CHIP 10K 5% 1/10W
R626 1-216-833-11 METAL CHIP 10K 5% 1/10W
R804 1-216-864-11 SHORT CHIP 0
R805 1-802-068-21 VARISTOR, CHIP (1608)
R806 1-216-841-11 METAL CHIP 47K 5% 1/10W
R807 1-216-841-11 METAL CHIP 47K 5% 1/10W
R810 1-216-857-11 METAL CHIP 1M 5% 1/10W
R811 1-216-845-11 METAL CHIP 100K 5% 1/10W
R812 1-216-845-11 METAL CHIP 100K 5% 1/10W
R815 1-216-833-11 METAL CHIP 10K 5% 1/10W
R817 1-216-833-11 METAL CHIP 10K 5% 1/10W
R818 1-216-845-11 METAL CHIP 100K 5% 1/10W
R821 1-216-845-11 METAL CHIP 100K 5% 1/10W
R823 1-216-821-11 METAL CHIP 1K 5% 1/10W
R828 1-216-821-11 METAL CHIP 1K 5% 1/10W
R829 1-216-845-11 METAL CHIP 100K 5% 1/10W
R830 1-216-821-11 METAL CHIP 1K 5% 1/10W
R831 1-216-821-11 METAL CHIP 1K 5% 1/10W
R832 1-216-821-11 METAL CHIP 1K 5% 1/10W
R833 1-216-821-11 METAL CHIP 1K 5% 1/10W
R834 1-216-821-11 METAL CHIP 1K 5% 1/10W
R839 1-216-845-11 METAL CHIP 100K 5% 1/10W
R840 1-216-845-11 METAL CHIP 100K 5% 1/10W
R841 1-216-845-11 METAL CHIP 100K 5% 1/10W
R843 1-216-833-11 METAL CHIP 10K 5% 1/10W
R844 1-216-833-11 METAL CHIP 10K 5% 1/10W
MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
20
D-EJ011
< SWITCH >
S801 1-786-865-11 SWITCH, KEYBOARD (u)
S802 1-786-865-11 SWITCH, KEYBOARD (>)
S803 1-786-865-11 SWITCH, KEYBOARD (.)
S804 1-786-865-11 SWITCH, KEYBOARD (VOL –)
S805 1-786-865-11 SWITCH, KEYBOARD (VOL +)
S807 1-786-865-11 SWITCH, KEYBOARD (x)
S808 1-786-865-11 SWITCH, KEYBOARD (SOUND/AVLS)
S809 1-786-865-11 SWITCH, KEYBOARD (P MODE/F)
S811 1-570-953-11 SWITCH, PUSH (1 KEY) (OPEN)
S812 1-786-864-11 SWITCH, SLIDE (HOLD”)
< VIBRATOR >
X601 1-813-590-11 VIBRATOR, CERAMIC (16.934 MHz)
************************************************************
MISCELLANEOUS
**************
07 A-1112-193-A CDM-3525A
LCD801 1-805-860-11 DISPLAY PANEL, LIQUID CRYSTAL
************************************************************
ACCESSORIES
************
1-542-697-51 HEADPHONE (MDR-E706)
2-896-703-41 MANUAL, INSTRUCTION (ENGLISH) (E)
2-896-703-61 MANUAL, INSTRUCTION (SIMPLIFIED
CHINESE, TRADITIONAL CHINESE)(E)
2-898-323-11 MANUAL, INSTRUCTION (KOREAN) (KR)
MAIN