Sony CDP-XE330 User manual

http://cxema.ru
CDP-XE330
AEP Model
UK Model
SERVICE MANUAL
COMPACT DISC PLAYER
MICROFILM
SPECIFICATIONS
Model Name Using Similar Mechanism CDP-XE220/XE320
CD Mechanism Type CDM14FL-5BD29C
Base Unit Name BU-5BD29C
Optical Pick-up Name KSS-213BA/F-NP
Compact Disc Player
Laser Semiconductor laser (λ= 780 nm)
Emission duration: continuous
Laser output Max 44.6 µW*
* This output is the value measured at a distance of
200 mm from the objective lens surface on the
Optical Pick-up block with 7 mm aperture.
Frequency response 2 Hz to 20 kHz ± 0.5 dB
Signal-to-noise ratio More than 100 dB
Dynamic range More than 92 dB
Harmonic distortion Less than 0.005%
Channel separation More than 95 dB
Output
Jack Maximum Load
type output impedance
level
LINE OUT Phono 2 V Over 10 kΩ
jacks (at 50 kΩ)
DIGITAL OUT Optical –18 dBm Wave length:
(OPTICAL) output 660 nm
connector
General
Power requirements 220 V – 230 VAC, 50/60 Hz
Power consumption 10W
Dimensions (approx.) 430 ×110 ×290 mm
(w/h/d) (17 ×4 3/8×11 1/2in.) incl. projecting parts
Mass (approx.) 3.1 kg (6 lbs 14 oz)
Supplied accessories
Audio cord (2 phono plugs–2 phono plugs) (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
Design and specifications are subject to change without notice.

http://cxema.ru
— 6 —
4-3. Aging Mode
This unit is equipped with an aging mode to check operations of the
mechanism deck.
• When faults occur:
Aging stops, and the state when aging stopped is displayed on the
fluorescent display tube.
• When no fault has occurred:
Aging is continued repeatedly.
Aging method 1
(When using the aging mode remote controller (J-2501-123-A)):
1. Press the Ubutton and turn ON the power.
2. Set the disc on the tray.
3. Press the AGINGSTART buttonoftheaging remote controller.
4. Aging starts and the message shown in Fig. 1 is displayed on
the fluorescent display tube.
5. To end, press the Ubutton.
Aging method 2 (When no aging mode remote controller):
1. Press the Ubutton and turn ON the power.
2. Set the disc on the tray.
3. Press the ∏button, CHECK button, and PLAY MODE
button together in this order.
4. Aging starts and the message shown in Fig. 1 is displayed on
the fluorescent display tube.
5. To end, press the Ubutton.
Fig. 1 Message in Aging Mode
SECTION 4
TEST MODE
4-1. AF MODE
The following checks can be performed in the AF mode, which is
setbyconnecting theTP2 (JW40 :AFADJ)terminalon MAIN board
to the Ground and turning on the power.
• FL tube check
After all segments light up, when the ·button is pressed
continuously, the following will be displayed. (Partial lighting 1)
When the pbutton is pressed continuously, the following will be
displayed. (partial lighting 2)
When the OPEN/CLOSE §button is pressed continuously, all
will light up again.
• Key check
All buttons have corresponding button numbers. When a button
is pressed, the counter will count up and display the button’s
number. However, the counter will only count to “13”. It will not
countfor buttonsalready pressed once,but willdisplaythe button’s
number.
P
ENTER (AMS)
0
)
TIME
REPEAT
PLAY MODE
02
04
05
06
07
08
09
PEAK SERCH
CHECK
CLEAR
OPEN/
CLOSE §
PLAY ·
STOP p
10
11
12
All lit
Partial lighting 1
Partial lighting 2
Button Button No.
Displayed Button Button No. Displayed
When the AMS knob is rotated to the right, the music calendar
changes from 1 n– – n20 n1.
When rotated to the left, it changes from 20 n1 n20 – –
• Remote commander check
When the ·button of the remote commander is pressed, the
“·” lights up. All go off when the other buttons are pressed.
4-2. ADJ MODE
The following operations are performed in the ADJ mode, which
is set by connecting the TP3 (JW41 :ADJ) terminal to the Ground
and turning on the power.
FUNCTIONS OF NUMBER BUTTONS
(With the general remote commander)
888(Partial lighting 1)
24
6810
12 14
16 18 20 (Partial lighting 2)
Â
Display of counting
888888
Â
Display of button number
Function
Button
Focus bias adjustment plus (Not used in servicing)
EF-BALANCE adjustment plus (Not used in servicing)
Tracking servo off
Tracking gain adjusting plus (Not used in servicing)
Laser power control off (Not used in servicing)
Focus bias adjustment minus (Not used in servicing)
EF-BALANCE adjustment minus (Not used in servicing)
Tracking servo on
Tracking gain adjustment minus ((Not used in servicing)
Laser power control on (Not used in servicing)
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
Load in
Access to TOC
Access to last track
Playback of last track
(3 seconds)
Access to first track
Playback of first track
(3 seconds)
Load out
A0
A1
A2
Counter display
A4
Counter display
A6
E0
E1
E2
E3
E4
E5
E6
Code
No. State Display when normal Display when abnormal

http://cxema.ru
CDP-XE330
— 13 — — 14 —
(Page 18)
16
BA/F-NP
6-3. SCHEMATIC DIAGRAM — BD SECTION — • Refer to page 23 for IC Pin Functions.
• Refer to page 29 for IC Block Diagrams.
500mV/DIV, 500nsec/DIV
1
IC101 #£ RFO
5
IC103 ^º XPCK
6
IC103 ^™ RFCK
7
IC103 &¢ WFCK
8
IC103 *ª XTAI
2
IC101 2FEI
3
IC101 $¶ TEI
4
IC103 @¶ MDP
1.3Vp-p
200mV/DIV, 1µsec/DIV
0.5Vp-p
50mV/DIV, 1msec/DIV
0.2Vp-p
7.8µsec
2.5Vp-p
230µsec
5Vp-p
135µsec
5Vp-p
16.9344MHz
2.6Vp-p
135µsec
5Vp-p
•Waveform

http://cxema.ru
CDP-XE330
— 17 — — 18 —
6-5. SCHEMATIC DIAGRAM — MAIN SECTION — • Refer to page 31 for IC Block Diagrams.
(Page 14)
(Page 21)
C602
4700pF
C601
4700pF
S601
POWER
CN601
2P
CN603
2P
~
AC IN
POWER SW
BOARD
16
C901
6800µ16V
C909
100µ16V
D906
1SS133
D910
MTZJ4.7B
R901
330
The components identified by mark !or dotted line with mark !are critical for safety. Replace only with part number specified.

http://cxema.ru
CDP-XE330
— 21 — — 22 —
6-7. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 28 for IC Pin Functions.
(Page 18)
R521
1k
1 2
1 2
NO502
2P
NO301
2P
DISPLAY BOARD
KEY BOARD
16
4MHz
4.2Vp-p
1
IC501 #¡ EXTAL
•Waveform

http://cxema.ru
6-8. IC PIN FUNCTIONS • IC101 FOCUS/TRACKING/SLED SERVO RF AMP (CXA1992AR)(BD board)
Pin No. Pin Name I/O Function
FEO FEI FDFCT FGD FLB FE O FE M SRCH TGU TG2 FSET TA M TA O SL P SL M SL O ISET VCC LOCK CLK XLT DATA XRST C.OUT SENS1 SENS2 FOK CC2 CC1 CB CP RF I RF O
O
I I I I
O
I I I I I I
O
I I
O
I
I I I I I I
O O O O
I
O
I I I
O
1
2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
Focus error amplifier output
Connected internally to the window comparator input for bias adjustment Focus error input Capacitor connection pin for defect time constant Ground this pin through a capacitor for cutting the focus servo high-frequency gain External time constant setting pin for boosting the focus servo low-frequency Focus drive output Focus amplifier inverted input External time constant setting pin for generating focus search waveform External time constant setting pin for switching tracking high-frequency gain External time constant setting pin for switching tracking high-frequency gain Peak frequency setting pin for focus and tracking phase compensation amplifier Tracking amplifier inverted input Tracking drive output Sled amplifier non-inverted input Sled amplifier inverted input Sled drive output Connect an external capacitance to set the current which determines the Focus search, Track jump, and Sled kick heights Positive power supply The sled overrun prevention circuit operates when this pin is Low (No pull-up resistance) Serial data transfer clock input from CPU (No pull-up resistance) Lach input from CPU (No pull-up resistance) Serial data input from CPU (No pull-up resistance) Reset input; resets at Low (No pull-up resistance) Track number count signal output Outputs FZC, DFCT1, TZC, BALH, TGH, FOH, ATSC, and others according to the command from CPU Outputs DFCT2, MIRR, BALL, TGL, FOL,and others according to the command from CPU Focus OK comparator output Input for the defect bottom hold output with capacitance coupled Defect bottom hold output Connected internally to the interruption comparator input Connection pin for defect bottom hold capacitor Connection pin for MIRR hold capacitor MIRR comparator non-inverted input Input for the RF summing amplifier output with capacitance coupled RF summing amplifier output Eye-pattern check point
• Abbreviation
FZC : Focus zero-cross DFCT : Defect TZC : Tracking zero-cross BALH: E-F Balance (High) TGH : Tracking Gain (High) FOH : Focus Bias (High)
34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
Pin No. Pin Name I/O Function
RF M RFTC LD PD PD1 PD2 FE BIAS F E EI VEE TEO LPFI TEI ATSC TZC TDFCT VC FZC
I I
O
I I I I I I
–
–
O
I I I I I
O
I
RF summing amplifier inverted input
The RF amplifier gain is determined by the resistance connected between this pin and RFO pin External time constant setting pin during RF level control APC amplifier output APC amplifier input RF I-V amplifier inverted input Connect these pins to the photo diode A+C and B+D pins Bias adjustment of focus error amplifier Leave this pin open for automatic adjustment F I-V and E I-V amplifier inverted input Connect these pins to photo diodes F and E I-V amplifier E gain adjustment (When not using automatic balance adjustment) Negative power supply Tracking error amplifier output E-F signal is output Comparator input for balance adjustment (Input from TEO through LPF) Tracking error input Window comparator input for ATSC detection Trackig zero-cross comparator input Capacitor connection pin for defect time constant (VCC + VEE)/2 direct voltage output Focus zero-cross comparator input
• Abbreviation
APC : Auto Power Control
ATSC : Anti Shock MIRR : Mirror BALL : E-F Balance (Low) TGL : Tracking Gain (Low) FOL : Focus Bias (Low)
— 23 — — 24 —

http://cxema.ru
— 25 —
Pin No. Pin Name I/O Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
• IC103 DIGITAL SIGNAL PROCESSOR (CXD2529Q)(BD board)
• Abbreviation
GFS :Guarded Frame Sync
PLL : Phase Locked Loop
VDD
VSS
LMUT
RMUT
ACDT
CKOUT
SQCK
SQSO
SENS
DATA
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
CLKO
SPOA
SPOB
SPOC
SPOD
XLON
FOK
VDD
VSS
MON
MDP
MDS
LOCK
PWMI
TES0
TES1
VPCO2
VPCO1
VCKI
V16M
VCTL
PCO
FILO
FILI
–
–
O
O
O
O
I
O
O
I
I
I
I
I
O
O
O
I
I
I
I
O
I
–
–
O
O
O
O
I
I
I
O
O
I
O
I
O
O
I
+5V power supply
Ground
Lch “L” detection flog
Rch “L” detection flog
Test output (Not used)
Master clock divider output (Not used)
Clock input for SQSO read out
Serial output for Sub-Q 80bit
SENS signal output to CPU
Serial data input, supplied from CPU
Latch input, supplied from CPU
Serial data transfer clock input, supplied from CPU
SENS input from IC101
Numbers of track jump counted signal input
Serial data output to IC101
Serial data latch output to IC101
Serial data transfer clock output to IC101
Micro computer demodulation interface (Input A)
Micro computer demodulation interface (Input B)
Micro computer demodulation interface (Input C)
Micro computer demodulation interface (Input D)
Micro computer demodulation interface (Output)
Focus OK input
+5V power supply
Ground
Output to control ON/OFF of spindle motor (Not used)
Output to control spindle motor servo
Output to control spindle motor servo (Not used)
GFS is sampled by 460Hz
Input to control the outside spindle motor
Test pin (Connected to ground)
Test pin (Connected to ground)
Charge-pump output (Not used)
Charge-pump output (Not used)
VCO2 oscillator input (Not used)
VCO2 oscillator output (Not used)
VCO2 control voltage input
Charge-pump output to master PLL
Filter output to master PLL
Filter input for master PLL

http://cxema.ru
— 26 —
Pin No. Pin Name I/O Function
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
• Abbreviation
EFM : Eight to Fourteen Modulation
AVSS
CLTV
AVDD
RF
BIAS
ASYI
ASYO
ASYE
WDCK
LRCK
LRCKI
PCMD
PCMDI
BCK
BCKI
VSS
VDD
GTOP
XUGF
XPLCK
GFS
RFCK
C2PO
XRAOF
MNT3
MNT1
MNT0
XTSL
FSTT
C4M
DOUT
EMPH
EMPHI
WFCK
SCOR
SBSO
EXCK
VSS
VDD
SYSM
–
I
–
I
I
I
O
I
O
O
I
O
I
O
I
–
–
O
O
O
O
O
O
O
O
O
O
I
O
O
O
O
I
O
O
O
I
–
–
I
Analog ground
Control voltage input for VCO
Analog power supply
EFM signal input
Asymmetry circuit constant current input
Asymmetry comparate voltage input
EFM full swing output (“L” =VSS, “H” =VDD)
Asymmetry circuit ON/OFF (“L”=OFF, “H”=ON)
D/A interface Word clock f=2fs
D/A interface LR clock output f=Fs
D/A interface LR clock input f=Fs
D/A interface Serial data output
D/A interface Serial data input
D/A interface Bit clock output
D/A interface Bit clock input
Ground
+5V power supply
Not used
Not used
EFM decoder PLL clock output
“H” Playback EFM sync and interpolation protection timming much
Read frame clock signal output
Not used
Internal RAM overflow detection signal output (Not used)
Not used
Not used
Not used
Not used
2/3 divider output (Not used)
4.2336MHz output(Not used)
Digital audio signal output
Playback disc output in emphasis mode
“H” =Input when de-emphasis ON
Write frame clock signal output
Sub-code sync output
Sub-P through Sub-W serial output
Clock input for SBSO read-out
Ground
+5V power supply
System mute input

http://cxema.ru
— 27 —
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Pin Name
Pin No. I/O Function
—
AVSS
AVDD
AOUT1
AIN1
LOUT1
AVSS
XVDD
XTAI
XTAO
XVSS
AVSS
LOUT2
AIN2
AOUT2
AVDD
AVSS
—
—
XRST
–
–
–
O
I
O
–
–
I
O
–
–
O
I
O
–
–
–
–
I
Not used
Analog ground
Analog power supply
Lch analog output
Lch opamp input
Lch line output
Analog ground
Master clock power supply
X’tal oscillator circuit input
X’tal oscillator circuit output
Master clock ground
Analog ground
Rch line output
Rch opamp input
Rch analog output
Analog power supply
Analog ground
Not used
Not used
System reset input

http://cxema.ru
— 28 —
• IC501 SYSTEM CONTROL ( CXP82616-034Q)(DISPLAY board)
Pin No. Pin Name I/O Function
1 GND – Ground
2 RMIN I Remote control signal input
3 GND – Ground
4 to 7 — – Not used
8 CLK O Serial clock output
9 SENSE I Sense signal input from IC103 (CXD2529Q)
10 DATA O Serial data output
11 SQCK O Sub Q clock output
12 SQSO I Sub Q data input
13 SENSE2 I Sense signal input from IC101 (CXA1992AR)
14 — – Not used (Open)
15 XLAT O Serial latch output
16 to 19 MUTE O Muting control signal output
20 LD OUT O Loading motor control
21 LD IN O Loading motor control
22, 23 — – Not used (Open)
24 to 26 KEY 0 to KEY 2 I Key input 0 to 2
27 — – Not used (Open)
28 ADJ/AFADJ I Test mode terminal
29 IN/OUT SW I CD tray IN/OUT switch
30 RST I System reset terminal
31 EXTAL O System oscillator (4.0 MHz)
32 XTAL I System oscillator (4.0 MHz)
33 VSS – Ground
34 to 41 OPEN – Not used (Open)
42 to 62 S21 to S1 O FL segment signal output
63 to 67 1G to 5G O FL grid signal output
68 — – Not used (Open)
69, 70 6G, 7G O FL grid signal output
71 VFDP (–30V) – Pull down voltage (–30V)
72 VDD (+5V) – Power supply (+5V)
73, 74 GND – Ground
75 VDD – Power supply (+5V)
76, 77 — – Not used (Open)
78 SCOR I Sub code data request signal input
79, 80 GND – Ground
• Abbreviation
FL : Fluorescent indicator tube

http://cxema.ru
— 29 —
• CD section
6-9. IC BLOCK DIAGRAMS
IC101 CXA1992AR
–
+
+
–
–
+
12 3 45 6 7 8 9 10
20
19
17
16
15
14
131211
21
22
23
24
25
26
27282930313233343536373839
40
41
42
43
44
45
46
52
51
50
49
48
47
+
–
+
–
+
–
+
–
–
+
–
+
–
+
+
–
+
–
+
–
+
–
–
+
+
–
–
+
–
+
+
–
+
–
+
–
+
–
+
–
+
––
+
–
+
–
+–
+
+
–
+
–
–
+
+
–
–
+
–
+
+
–
18
–
+
–
+
–
+
+
–
+
–
–
+
Charge
up
FEO
FEI
FDFCT
FGD
FLB
FE_O
FE_M
SRCH
TGU
TG2
FSET
TA_M
TA_O
SL_P
SL_M
SL_O
ISET
VCC
VCC
LOCK
CLK
XLT
DATA
XRST
C. OUT
SENS1
SENS2
FOK CC2 CC1 CB CP RF_I RF_O RF_M RFTC LD PD PD1 PD2
FE_BIAS
F
E
EI
VEE
TEO
LPFI
TEI
ATSC
TZC
VC
FZC
TM2
VEEVEE
TM3 TM5
TM4 TM6
VCC VCC
TM7
ISET
TTL
↓
IIL
IIL
↓
TTL
IIL
↓
TTL
IIL DATA REGISTER
INPUT SHIFT REGISTER
ADDRESS DECODER
SENS SELECTOR
OUTPUT DECODER
DFCTO IFB1-6
BAL1-4
TOG1-4
FS1-4 TG1-2 TM1-7 PS1-4
FOH
FOL
TGH
TGL
BALH
BALL
ATSC
TZC
FZC
FSET
TG2
VEE
VCC
FS1
FS2
FOCUS
PHASE COMPENSATION
DFCT
FS4
TRACKING
PHASE COMPENSATION
TG1
TM1
DFCT
FZC COMP.
VEE
VCC
VCC
TDFCT
TZC COMP.
ATSC
WINDOW
COMP.
E-F BALANCE
WINDOW COMP.
TRK. GAIN
WINDOW COMP.
FO. BIAS
WINDOW
COMP.
VEE
TGFL
TOG1
TOG2
TOG3
TOG4
BAL1
BAL2
BAL3
BAL4
IFB1
IFB2 IFB3
IFB4 IFB5
IFB6
FE AMP
VEE
E IV AMP
F IV AMP
VCC
APC
VCC
VEE
LASER POWER CONTROL
VEE
PD1 IV
AMP
PD2 IV
AMP
RF SUMMING
AMP
VCC
VEE
VEE
LEVEL S VEE
MIRR
VCC
DFCT
FOK
VCC
LDON LPCL LPC TGFL MIRR DFCT1 CC1

http://cxema.ru
— 30 —
IC102 BA5941FP
IC103 CXD2529Q
+–
LEVEL SHIFT
+– +–
1 2 345678910 11 12 13 14
28 27
LEVEL SHIFT
+–
+
–
MUTE
+
–
+–
LEVEL SHIFT
+– +–
LEVEL SHIFT
+–
+
–
+
–
15
1617
18
19
21 20
22
26 25 24 23
+–
NC
Vcc
VccVcc
VCC
BIAS IN
IN1B IN1A IN2B IN2A
GND GND
MUTE
VCC
OUT2A OUT2B OUT1A OUT1B
IN4B IN4A IN3B IN3A OP OUT OP IN (–) OP IN (+) GND NC VCC OUT3A OUT3B OUT4A OUT4B
3RD-ORDER NOISE SHAPER
+
–
+
–
PWMPWM
+
–
+
–
VDD
VSS
LMUT
RMUT
TES2
CKOUT
SQCK
SQSO
SENS DATA
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
CLKO
SPOA SPOB SPOC
SPOD
XLON
FOK
VDD
VSS
MON
MDP MDS
LOCK
PWMI
1 2 3456789 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
LRCK
WDCK
ASYE
ASYO
ASYI
BIAS
RF
AVDD
CLTV
AVSS
FILI
FILO
PCO
VCTL
V16M
VCKI
VPCO1
VPCO2
TES1
TES0
43
42
41
40
39
38
37
36
35
34
33
32
31
50
49
48
47
46
45
44
NC
AVSS
AVDD
AOUT1
AIN1
LOUT1
AVSS
XVDD
XTAI
XTAO
XVSS
AVSS
LOUT2
AIN2
AOUT2
AVDD
AVSS
NC
NC
XRST
88
89
90
91
92
93
94
95
96
97
98
99
100
81
82
83
84
85
86
87
SYSM VDD VSS EXCK SBSO SCOR WFCK EMPHI EMPH DOUT C4M FSTT XTSL MNT0 MNT1 MNT3 XROF C2PO RFCK GFS XPCK XUGF GTOP VDD VSS BCKI BCK PCMDI PCMD LRCKI
71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
80 79 78 77 76 75 74 73 72
ASYMMETRY
CORRECTOR
DIGITAL
PLL
CLOCK
GENERATOR
D / A
INTERFACE
DIGITAL CLV
SERIAL-IN
INTERFACE OVER SAMPLING
DIGITAL FILTER SUB CODE
PROCESSOR
TIMING
LOGIC CPU
INTERFACE
SERVO
AUTO
SEQUENCER
ERROR
CORRECTOR
16K RAM DIGITAL OUT
OSC
EFM
DEMODURATOR

http://cxema.ru
— 31 —
• MAIN section
IC401 LB1641
IC701 LA5601
109876543
PRE
DRIVER
INPUT LOGIC BLOCK
GND OUT1 P1 VZ IN1 IN2 V
CC 1V CC 2 P2 OUT2
21
3
6
7
2 5
1
4
9
8
10
ON/OFF
AMP V REF AMP
RESET
VOMUTE
CD VIN
VO
RES
CN
GND
EN VID VOD

http://cxema.ru
SECTION 7
EXPLODEDVIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delayshould be anticipated whenorderingthese
items.
• Themechanical parts withno reference number
in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
• Abbreviation
AED : North European
The components identified by mark !or
dotted line with mark !are critical for safety.
Replace only with part number specified.
— 32 —
1 4-214-165-01 PANEL, LOADING
2 4-996-687-51 KNOB(AMS)
3 4-996-698-01 EMBLEM, SONY
4 3-354-981-11 SPRING (SUS), RING
5 4-977-593-11 RING(DIA. 50), ORNAMENTAL
6 X-4950-692-1 PANEL ASSY, FRONT
7 3-931-429-62 BUTTON (POWER)
*8 1-672-315-11 POWER SW BOARD
9 4-951-620-01 SCREW(2.6 ×8), +BVTP
*10 A-4724-499-A DISPLAY BOARD, COMPLETE
11 1-590-243-11 WIRE(FLAT TYPE) (21 CORE)
12 4-977-358-11 CUSHION
13 4-210-291-01 SCREW (CASE 3 TP2)
*14 4-980-777-01 CASE (409526)
!15 1-575-651-21 CORD, POWER
16 X-4947-207-1 FOOT ASSY (F50150S)
*17 4-954-051-51 HOLDER, PC BOARD
*18 A-4724-498-A MAIN BOARD, COMPLETE
*19 4-214-171-02 PANEL, BACK(AEP,AED,CIS)
*19 4-214-171-12 PANEL, BACK(UK)
20 4-966-267-11 BUSHING (FBS001), CORD
!21 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P(UK)
*22 1-672-314-11 KEY BOARD
!T901 1-423-979-21 TRANSFORMER, POWER
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
CDM14FL-5BD29C
1
24
3
5
12
6
789
22 9
9
9
10
11
13
13
14
11
16
17
18
19
20
15
T901
#1
#1
#1
#1
#1
#1
#2
#2
#1
#1
not supplied
not supplied
not supplied
9
9
UK model
21
7-1. MAIN SECTION

http://cxema.ru
— 33 —
101 1-452-925-21 MAGNET ASSY
102 4-933-110-41 HOLDER (MG)
103 4-995-814-21 TABLE (FL), DISC
104 4-967-268-01 GEAR (C)
105 4-927-649-01 BELT
106 4-933-107-01 GEAR (PL)
107 4-927-651-01 PULLEY (S)
108 4-933-109-01 CAM
109 1-645-721-11 LOADING BOARD
110 4-933-134-01 SCREW (+PTPWH M2.6 ×6)
111 4-959-996-01 SPRING (932), COMPRESSION
112 4-933-129-01 HOLDER (BU)
113 4-933-111-41 CHASSIS (MD)
114 4-917-583-21 BRACKET, YOKE
115 4-993-142-21 PULLEY (L), PRESS
M151 A-4604-363-A MOTOR (L) ASSY
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
101
102
110 110
111
112
113
114
M151
#3
111
103
115
104
105
106
107
108
109
BU-5BD29C
NOTE: There are two types of MAGNET ASSY.
Confirm the shape before replacing the parts.
not supplied
7-2. CD MECHANISM SECTION (CDM14FL-5BD29C)

http://cxema.ru
— 34 —
!151 8-848-379-31 OPTICAL PICK-UP KSS-213BA/F-NP
152 1-769-069-11 WIRE (FLAT TYPE) (16 CORE)
153 4-917-567-01 GEAR (M)
154 4-951-940-01 INSULATOR (BU)
155 4-917-565-01 SHAFT, SLED
156 4-917-564-01 GEAR (P), FLATNESS
*157 A-4724-297-A BD BOARD, COMPLETE
158 3-713-786-51 SCREW +P 2 ×3
M101 X-4917-523-4 MOTOR ASSY(SPINDLE)
M102 X-4917-504-1 MOTOR ASSY(SLED)
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
151
152
153
158
154
156
M102
M101
#4
157
155
154
7-3. BASE UNIT SECTION (BU-5BD29C)
The components identified by mark !or dotted
line with mark !are critical for safety.
Replace only with part number specified.

http://cxema.ru
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
— 35 —
SECTION 8
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specifiedin thediagrams or thecomponents
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• CAPACITORS:
uF: µF
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• COILS
uH: µH
• Abbreviation
AED : North European
The components identified by mark !or
dotted line with mark !are critical for safety.
Replace only with part number specified.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
*A-4724-297-A BD BOARD, COMPLETE
******************
< CAPACITOR >
C101 1-126-607-11 ELECT CHIP 47uF 20% 4V
C102 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C103 1-164-346-11 CERAMIC CHIP 1uF 16V
C105 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C106 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C107 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C108 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C109 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C111 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C112 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C113 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C114 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V
C116 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V
C117 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C118 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C119 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C120 1-124-779-00 ELECT CHIP 10uF 20% 16V
C121 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C122 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C123 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C124 1-126-607-11 ELECT CHIP 47uF 20% 4V
C125 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C126 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C127 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
C129 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C130 1-164-336-11 CERAMIC CHIP 0.33uF 25V
C131 1-164-346-11 CERAMIC CHIP 1uF 16V
C140 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V
C154 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C161 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C162 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C163 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
C164 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
C165 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C166 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
C167 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
C168 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
C169 1-163-121-00 CERAMIC CHIP 150PF 5% 50V
C170 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C171 1-163-237-11 CERAMIC CHIP 27PF 5% 50V
C173 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C174 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C175 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C176 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C177 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C178 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C179 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C181 1-126-205-11 ELECT CHIP 47uF 20% 6.3V
C182 1-126-395-11 ELECT 22uF 20% 16V
C183 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C185 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V
C188 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C189 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
< CONNECTOR >
CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P
CNU102 1-784-360-11 CONNECTOR,FFC(LIF(NON-ZIF))21P
< FERRITE BEAD >
FB101 1-414-234-22 INDUCTOR CHIP 0UH
FB103 1-414-234-22 INDUCTOR CHIP 0UH
< IC >
IC101 8-752-080-62 IC CXA1992AR
IC102 8-759-429-32 IC BA5941FP-E2
IC103 8-752-380-64 IC CXD2529Q
< JUMPER RESISTOR >
JW101 1-216-295-91 SHORT 0
JW104 1-216-295-91 SHORT 0
< TRANSISTOR >
Q101 8-729-010-08 TRANSISTOR MSB710-R
< RESISTOR >
R102 1-216-001-00 METAL CHIP 10 5% 1/10W
R104 1-216-093-91 RES,CHIP 68K 5% 1/10W
R105 1-216-088-00 METAL CHIP 43K 5% 1/10W
R106 1-216-088-00 METAL CHIP 43K 5% 1/10W
R107 1-216-088-00 METAL CHIP 43K 5% 1/10W
R108 1-216-088-00 METAL CHIP 43K 5% 1/10W
R109 1-216-093-91 RES,CHIP 68K 5% 1/10W
R114 1-216-101-00 METAL CHIP 150K 5% 1/10W
R115 1-216-101-00 METAL CHIP 150K 5% 1/10W
R116 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R117 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R118 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
R119 1-216-085-00 METAL CHIP 33K 5% 1/10W
R120 1-216-089-91 RES,CHIP 47K 5% 1/10W
R121 1-216-114-00 RES,CHIP 510K 5% 1/10W
BD

http://cxema.ru
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
— 36 —
R122 1-216-097-91 RES,CHIP 100K 5% 1/10W
R123 1-216-099-00 METAL CHIP 120K 5% 1/10W
R124 1-216-091-00 METAL CHIP 56K 5% 1/10W
R125 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R126 1-216-063-91 RES,CHIP 3.9K 5% 1/10W
R127 1-216-089-91 RES,CHIP 47K 5% 1/10W
R128 1-216-098-00 METAL CHIP 110K 5% 1/10W
R129 1-216-049-91 RES,CHIP 1K 5% 1/10W
R130 1-216-079-00 METAL CHIP 18K 5% 1/10W
R131 1-216-079-00 METAL CHIP 18K 5% 1/10W
R132 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R133 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R134 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R135 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R136 1-216-073-00 METAL CHIP 10K 5% 1/10W
R137 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R138 1-216-025-91 RES,CHIP 100 5% 1/10W
R156 1-216-081-00 METAL CHIP 22K 5% 1/10W
R157 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R158 1-216-001-00 METAL CHIP 10 5% 1/10W
R159 1-216-121-91 RES,CHIP 1M 5% 1/10W
R161 1-216-097-91 RES,CHIP 100K 5% 1/10W
R162 1-216-073-00 METAL CHIP 10K 5% 1/10W
R163 1-216-121-91 RES,CHIP 1M 5% 1/10W
R164 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R165 1-216-049-91 RES,CHIP 1K 5% 1/10W
R166 1-216-073-00 METAL CHIP 10K 5% 1/10W
R167 1-216-683-11 METAL CHIP 22K 0.5% 1/10W
R168 1-216-073-00 METAL CHIP 10K 5% 1/10W
R169 1-216-079-00 METAL CHIP 18K 5% 1/10W
R170 1-216-683-11 METAL CHIP 22K 0.5% 1/10W
R171 1-216-073-00 METAL CHIP 10K 5% 1/10W
R172 1-216-079-00 METAL CHIP 18K 5% 1/10W
R173 1-216-049-91 RES,CHIP 1K 5% 1/10W
R174 1-216-033-00 METAL CHIP 220 5% 1/10W
R175 1-216-025-91 RES,CHIP 100 5% 1/10W
R176 1-216-049-91 RES,CHIP 1K 5% 1/10W
R177 1-216-049-91 RES,CHIP 1K 5% 1/10W
R178 1-216-049-91 RES,CHIP 1K 5% 1/10W
R179 1-216-025-91 RES,CHIP 100 5% 1/10W
R180 1-216-025-91 RES,CHIP 100 5% 1/10W
R181 1-216-025-91 RES,CHIP 100 5% 1/10W
R182 1-216-025-91 RES,CHIP 100 5% 1/10W
R183 1-216-025-91 RES,CHIP 100 5% 1/10W
R188 1-216-037-00 METAL CHIP 330 5% 1/10W
R189 1-216-025-91 RES,CHIP 100 5% 1/10W
R190 1-216-097-91 RES,CHIP 100K 5% 1/10W
R191 1-216-105-91 RES,CHIP 220K 5% 1/10W
< SWITCH >
S101 1-572-085-11 SWITCH, LEAF (LIMIT SW)
< VIBRATOR >
X101 1-767-408-21 VIBRATOR, CRYSTAL 16.9344 MHz
************************************************************
*A-4724-499-A DISPLAY BOARD, COMPLETE
***********************
*4-929-709-31 GUIDE(FL TUBE)
< CAPACITOR >
C501 1-161-494-00 CERAMIC 0.022uF 25V
C502 1-161-494-00 CERAMIC 0.022uF 25V
C503 1-164-159-11 CERAMIC 0.1uF 50V
C504 1-164-159-11 CERAMIC 0.1uF 50V
C506 1-124-584-00 ELECT 100uF 20% 10V
< CONNECTOR >
CN501 1-568-864-11 CONNECTOR, FFC 21P
< FLUORESCENT INDICATOR TUBE >
FL501 1-517-297-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC501 8-752-880-56 IC CXP82616-034Q
IC502 8-749-014-66 IC NJL56H400A(REMOTE SENSOR)
< TRANSISTOR >
Q501 8-729-029-66 TRANSISTOR DTC114ESA
< RESISTOR >
R501 1-249-427-11 CARBON 6.8K 5% 1/4W F
R502 1-249-427-11 CARBON 6.8K 5% 1/4W F
R503 1-249-427-11 CARBON 6.8K 5% 1/4W F
R506 1-249-417-11 CARBON 1K 5% 1/4W F
R507 1-249-419-11 CARBON 1.5K 5% 1/4W F
R508 1-249-421-11 CARBON 2.2K 5% 1/4W F
R509 1-249-427-11 CARBON 6.8K 5% 1/4W F
R510 1-249-415-11 CARBON 680 5% 1/4W F
R511 1-249-417-11 CARBON 1K 5% 1/4W F
R512 1-249-419-11 CARBON 1.5K 5% 1/4W F
R513 1-249-427-11 CARBON 6.8K 5% 1/4W F
R514 1-249-415-11 CARBON 680 5% 1/4W F
R515 1-247-807-31 CARBON 100 5% 1/4W
R516 1-249-441-11 CARBON 100K 5% 1/4W
R517 1-247-843-11 CARBON 3.3K 5% 1/4W
R518 1-249-427-11 CARBON 6.8K 5% 1/4W F
R519 1-249-431-11 CARBON 15K 5% 1/4W
R520 1-247-807-31 CARBON 100 5% 1/4W
R521 1-249-417-11 CARBON 1K 5% 1/4W F
< SWITCH >
S508 1-762-752-11 SWITCH, TACTILE(PEAK SEARCH)
S509 1-762-752-11 SWITCH, TACTILE(CHECK)
S510 1-762-752-11 SWITCH, TACTILE(CLEAR)
S511 1-762-752-11 SWITCH, TACTILE(OPEN/CLOSE)
S512 1-762-752-11 SWITCH, TACTILE(·)
S513 1-762-752-11 SWITCH, TACTILE(P)
S514 1-762-752-11 SWITCH, TACTILE(p)
S515 1-762-752-11 SWITCH, TACTILE())
S516 1-762-752-11 SWITCH, TACTILE(0)
S520 1-475-543-11 ENCODER, ROTARY(AMS)
< VIBRATOR >
X501 1-577-082-11 VIBRATOR, CERAMIC 4.0MHz
************************************************************
BD DISPLAY

http://cxema.ru
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
— 37 —
*1-672-314-11 KEY BOARD
*********
< RESISTOR >
R504 1-249-415-11 CARBON 680 5% 1/4W F
R505 1-249-417-11 CARBON 1K 5% 1/4W F
< SWITCH >
S502 1-762-752-11 SWITCH, TACTILE(TIME)
S503 1-762-752-11 SWITCH, TACTILE(REPEAT)
S504 1-762-752-11 SWITCH, TACTILE(PLAY MODE)
************************************************************
1-645-721-11 LOADING BOARD
*************
< CONNECTOR >
*CN151 1-568-943-11 PIN, CONNECTOR 5P
< SWITCH >
S151 1-572-086-11 SWITCH, LEAF(LOAD OUT)
S152 1-572-086-11 SWITCH, LEAF(LOAD IN)
************************************************************
*A-4724-498-A MAIN BOARD, COMPLETE
********************
< CAPACITOR >
C301 1-162-286-31 CERAMIC 220PF 10% 50V
C302 1-130-479-00 MYLAR 0.0047uF 5% 50V
C303 1-104-664-11 ELECT 47uF 20% 16V
C304 1-162-286-31 CERAMIC 220PF 10% 50V
C305 1-130-472-00 MYLAR 0.0012uF 5% 50V
C306 1-161-494-00 CERAMIC 0.022uF 25V
C307 1-162-290-31 CERAMIC 470PF 10% 50V
C308 1-104-666-11 ELECT 220uF 20% 25V
C309 1-161-494-00 CERAMIC 0.022uF 25V
C310 1-164-159-11 CERAMIC 0.1uF 50V
C351 1-162-286-31 CERAMIC 220PF 10% 50V
C352 1-130-479-00 MYLAR 0.0047uF 5% 50V
C353 1-104-664-11 ELECT 47uF 20% 16V
C354 1-162-286-31 CERAMIC 220PF 10% 50V
C355 1-130-472-00 MYLAR 0.0012uF 5% 50V
C356 1-161-494-00 CERAMIC 0.022uF 25V
C357 1-162-290-31 CERAMIC 470PF 10% 50V
C401 1-161-494-00 CERAMIC 0.022uF 25V
C402 1-162-306-11 CERAMIC 0.01uF 20% 16V
C403 1-126-964-11 ELECT 10uF 20% 50V
C602 1-113-924-11 CERAMIC 0.0047uF 20% 250V
C702 1-126-964-11 ELECT 10uF 20% 50V
C703 1-162-294-31 CERAMIC 0.001uF 10% 50V
C704 1-104-666-11 ELECT 220uF 20% 25V
C705 1-126-964-11 ELECT 10uF 20% 50V
C706 1-126-933-11 ELECT 100uF 20% 16V
C707 1-126-960-11 ELECT 1uF 20% 50V
C708 1-126-964-11 ELECT 10uF 20% 50V
C710 1-126-964-11 ELECT 10uF 20% 50V
C711 1-164-159-11 CERAMIC 0.1uF 50V
C713 1-164-159-11 CERAMIC 0.1uF 50V
C714 1-164-159-11 CERAMIC 0.1uF 50V
C715 1-126-933-11 ELECT 100uF 20% 16V
C716 1-162-290-31 CERAMIC 470PF 10% 50V
C717 1-162-290-31 CERAMIC 470PF 10% 50V
C718 1-164-159-11 CERAMIC 0.1uF 50V
C901 1-128-547-11 ELECT 6800uF 20% 16V
C903 1-128-576-11 ELECT 100uF 20% 63V
C904 1-164-159-11 CERAMIC 0.1uF 50V
C905 1-161-494-00 CERAMIC 0.022uF 25V
C909 1-126-933-11 ELECT 100uF 20% 16V
< CONNECTOR >
CN401 1-784-782-11 CONNECTOR, FFC 21P
CN402 1-784-782-11 CONNECTOR, FFC 21P
CN602 1-564-321-00 PIN, CONNECTOR 2P
< DIODE >
D401 8-719-911-19 DIODE 1SS119
D402 8-719-109-97 DIODE RD6.8ES-B2
D403 8-719-921-40 DIODE MTZJ-4.7C
D404 8-719-982-19 DIODE MTZJ-30A
D701 8-719-911-19 DIODE 1SS119
D702 8-719-911-19 DIODE 1SS119
D703 8-719-911-19 DIODE 1SS119
D704 8-719-911-19 DIODE 1SS119
D705 8-719-911-19 DIODE 1SS119
D706 8-719-911-19 DIODE 1SS119
D901 8-719-024-99 DIODE 11ES2-NTA2B
D902 8-719-024-99 DIODE 11ES2-NTA2B
D903 8-719-024-99 DIODE 11ES2-NTA2B
D904 8-719-024-99 DIODE 11ES2-NTA2B
D905 8-719-024-99 DIODE 11ES2-NTA2B
D906 8-719-911-19 DIODE 1SS119
D910 8-719-921-40 DIODE MTZJ-4.7C
< TERMINAL >
*EB1 1-537-738-21 TERMINAL, EARTH
< IC >
IC301 8-759-634-51 IC M5218AP
IC302 8-759-634-51 IC M5218AP
IC303 8-749-921-12 IC GP1F32T(DIGITAL OUT)
IC401 8-759-822-09 IC LB1641
IC701 8-759-821-93 IC LA5601
< JACK >
J401 1-785-868-11 JACK, PIN 2P(LINE OUT)
< COIL >
L701 1-414-223-11 INDUCTOR 470uH
L703 1-410-507-11 INDUCTOR 6.8uH
L704 1-410-322-11 INDUCTOR 3.3uH
< TRANSISTOR >
Q302 8-729-922-37 TRANSISTOR 2SD2144S
Q303 8-729-922-37 TRANSISTOR 2SD2144S
Q304 8-729-029-56 TRANSISTOR DTA144ESA
Q352 8-729-922-37 TRANSISTOR 2SD2144S
Q353 8-729-922-37 TRANSISTOR 2SD2144S
KEY LOADING MAIN

http://cxema.ru
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
— 38 —
Q354 8-729-029-56 TRANSISTOR DTA144ESA
Q401 8-729-041-38 TRANSISTOR 2SB1241TV2Q
Q402 8-729-119-76 TRANSISTOR 2SA1175-HFE
Q701 8-729-029-56 TRANSISTOR DTA144ESA
< RESISTOR >
R301 1-247-848-11 CARBON 5.1K 5% 1/4W
R302 1-249-429-11 CARBON 10K 5% 1/4W
R303 1-249-432-11 CARBON 18K 5% 1/4W
R304 1-249-420-11 CARBON 1.8K 5% 1/4W F
R305 1-249-420-11 CARBON 1.8K 5% 1/4W F
R307 1-249-432-11 CARBON 18K 5% 1/4W
R308 1-247-891-00 CARBON 330K 5% 1/4W
R310 1-247-807-31 CARBON 100 5% 1/4W
R311 1-249-429-11 CARBON 10K 5% 1/4W
R312 1-249-429-11 CARBON 10K 5% 1/4W
R313 1-249-417-11 CARBON 1K 5% 1/4W F
R314 1-249-421-11 CARBON 2.2K 5% 1/4W F
R315 1-247-807-31 CARBON 100 5% 1/4W
R316 1-249-421-11 CARBON 2.2K 5% 1/4W F
R318 1-249-441-11 CARBON 100K 5% 1/4W
R320 1-247-807-31 CARBON 100 5% 1/4W
R351 1-247-848-11 CARBON 5.1K 5% 1/4W
R352 1-249-429-11 CARBON 10K 5% 1/4W
R353 1-249-432-11 CARBON 18K 5% 1/4W
R354 1-249-420-11 CARBON 1.8K 5% 1/4W F
R355 1-249-420-11 CARBON 1.8K 5% 1/4W F
R357 1-249-432-11 CARBON 18K 5% 1/4W
R358 1-247-891-00 CARBON 330K 5% 1/4W
R360 1-247-807-31 CARBON 100 5% 1/4W
R361 1-249-429-11 CARBON 10K 5% 1/4W
R362 1-249-429-11 CARBON 10K 5% 1/4W
R363 1-249-417-11 CARBON 1K 5% 1/4W F
R364 1-249-421-11 CARBON 2.2K 5% 1/4W F
R365 1-247-807-31 CARBON 100 5% 1/4W
R366 1-249-421-11 CARBON 2.2K 5% 1/4W F
R368 1-249-441-11 CARBON 100K 5% 1/4W
R370 1-247-807-31 CARBON 100 5% 1/4W
R401 1-249-432-11 CARBON 18K 5% 1/4W
R402 1-249-441-11 CARBON 100K 5% 1/4W
R403 1-249-425-11 CARBON 4.7K 5% 1/4W F
R404 1-249-441-11 CARBON 100K 5% 1/4W
R405 1-249-432-11 CARBON 18K 5% 1/4W
R406 1-249-427-11 CARBON 6.8K 5% 1/4W F
R407 1-249-432-11 CARBON 18K 5% 1/4W
R408 1-249-427-11 CARBON 6.8K 5% 1/4W F
R701 1-249-419-11 CARBON 1.5K 5% 1/4W F
R702 1-249-441-11 CARBON 100K 5% 1/4W
R704 1-247-807-31 CARBON 100 5% 1/4W
R705 1-249-417-11 CARBON 1K 5% 1/4W F
R706 1-247-807-31 CARBON 100 5% 1/4W
R707 1-247-807-31 CARBON 100 5% 1/4W
R708 1-247-807-31 CARBON 100 5% 1/4W
R901 1-249-411-11 CARBON 330 5% 1/4W
< TRANSFORMER >
!T901 1-423-979-21 TRANSFORMER, POWER
************************************************************
*1-672-315-11 POWER SW BOARD
***************
< CAPACITOR >
!C601 1-113-924-11 CERAMIC 0.0047uF 20% 250V
< CONNECTOR >
*CN601 1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P
CN603 1-769-745-71 LEAD (WITH CONNECTOR) (2 CORE)
< SWITCH >
!S601 1-572-267-51 SWITCH, PUSH (AC POWER)(1 KEY)(POWER)
************************************************************
MISCELLANEOUS
*************
11 1-590-243-11 WIRE(FLAT TYPE) (21 CORE)
!15 1-575-651-21 CORD, POWER
!21 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P(UK)
101 1-452-925-21 MAGNET ASSY
!151 8-848-379-31 OPTICAL PICK-UP KSS-213BA/F-NP
152 1-769-069-11 WIRE (FLAT TYPE) (16 CORE)
M101 X-4917-523-4 MOTOR ASSY(SPINDLE)
M102 X-4917-504-1 MOTOR ASSY(SLED)
M151 A-4604-363-A MOTOR (L) ASSY
************************************************************
ACCESSORIES & PACKING MATERIALS
*******************************
1-467-880-11 REMOTE COMMANDER (RM-D420)
1-776-263-11 CORD,CONNECTION (AUDIO)
3-865-462-11 MANUAL, INSTRUCTION
(ENGLISH/FRENCH/SPANISH)(AEP/UK)
3-865-462-21 MANUAL, INSTRUCTION
(GERMAN/DUTCH/ITALIAN/PORTUGUESE)(AEP)
3-865-462-31 MANUAL, INSTRUCTION
(SWEDISH/DANISH/FINNISH)(AED)
3-865-462-41 MANUAL, INSTRUCTION
(ENGLISH/POLISH/RUSSIAN)(CIS)
3-865-462-51 MANUAL, INSTRUCTION(HUNGARIAN)(CIS)
3-865-462-61 MANUAL, INSTRUCTION(CZECH)(CIS)
3-865-462-71 MANUAL, INSTRUCTION(TURKISH)(CIS)
3-865-462-81 MANUAL, INSTRUCTION(GREEK)(CIS)
4-962-615-01 COVER, BATTERY (For RM-D420)
************************************************************
*************
HARDWARE LIST
*************
#1 7-685-646-79 SCREW +BVTP 3 ×8 TYPE2 N-S
#2 7-685-649-79 SCREW +BVTP 3 ×14 TYPE2 IT-3
#3 7-621-775-10 SCREW +B 2.6 ×4
#4 7-685-134-19 SCREW +BTP 2.6 ×8 TYPE2 N-S
The components identified by mark !or dotted
line with mark !are critical for safety.
Replace only with part number specified.
MAIN POWER SW
CDP-XE330
Sony Corporation
Home A&V Products Company
9-928-850-11 99D167549-1
Printed in Hungary ©1999.4
Published by Quality Assurance Dept.
(Shinagawa)