Sony D-E565 - Compact Disc Player User manual

Play
Compact Disc
Compact Player
Playing a CD right
aw ay!
If you want to play a CD right now, choose to use your player on house
current. Other choices are the following three: rechargeable batteries,
dry batteries (see “Power Sources” on the reverse side) and car battery.
Connect
Sony Corporation ©1999 Printed in Malaysia
3
1
For the custom ers in the USA
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
For the custom ers in Aust ralia
The supply cord of the AC power adaptor cannot
be replaced; if the cord is damaged, the AC
power adaptor should be discarded.
For the custom ers not in Europe
The CE mark on the unit is valid
only for products marketed in the
European Union.
to a wall
outlet
AC power adaptor
DC IN 4.5 V
1Slide OPEN to open the lid.
OPEN
Welcome!
Thank you for purchasing the Sony
Compact Disc Compact Player.
Before operating your player, please
read this manual and retain it for
future reference.
About this manual
The instructions in this manual are for the
D-E561 and D-E565. Before you start reading,
check your model number.
Ow ner’s Record
The model and the serial numbers are located at
the bottom. Record these numbers in the spaces
provided below. Refer to them whenever you
call upon your Sony dealer regarding this
product.
Model No. __________ Serial No.__________
WARNING
To prevent f ire or shock
hazard, do not expose
the unit to rain or
moisture.
To avoid elect rical
shock, do not open t he
cabinet . Refer servicing
to qualif ied personnel
only.
CAUTION
The use of optical instruments with this product
will increase eye hazard.
2/REM OTE
For models supplied w ith the remote control
• Connect the plug of the headphones to the remote control.
• Connect the headphones to the remote control firmly. A loose connection may cause noise
during playback.
Place a CD
2
2Adjust the volume.
1Press ^.
To stop play, press p.
To use t he rem ot e cont rol
1Press (.
2Adjust the volume.
Operating Instruct ions
About area code
The area code of the player you purchased is shown on upper left of the bar
code label on the package.
For accessories supplied with your player, check the area code of your model
and refer to “Supplied accessories” toward the end of this manual.
3-867-524-11 (1)
D-E561
D-E565
zOther Operat ions
Playing tracks repeatedly
(Repeat Play)
You can play tracks repeatedly in normal,
INTRO PGM, shuffle or RMS (Random Music
Sensor) play modes. Repeat all the tracks,
only one track or the specified part within the
same track.
To repeat all the t racks
Press REPEAT/ENTER during play.
The “ ” indication appears.
To cancel repeat play, press REPEAT/ENTER
again.
To repeat a single t rack
1Press REPEAT/ENTER while the track you
want to repeat is playing.
The “ ” indication appears.
2Press PLAY MODE repeatedly until “1”
appears.
To repeat another track, press =or +.
To cancel repeat play, press REPEAT/ENTER
again.
To repeat the specified part w ithin
the sam e t rack (LOOP Play)
1During play, press PLAY MODE
repeatedly until “A˜B” flashes in the
display.
2Press REPEAT/ENTER to set the point
(point A) where you want to start repeat
play.
Point A is stored in the memory.
3Press REPEAT/ENTER again to set the
point (point B) where you want to stop
repeat play.
Point B is stored in the memory, and repeat
play starts from point A.
To change points A and B, press and hold
REPEAT/ENTER until “A˜B” flashes in the
display, then do steps 2 and 3 again.
To set points A and B on other tracks, press
=or +to select another track, then do
steps 2 and 3 again.
If you press p, the stored points will be
erased. To prevent accidental erasure, set the
RESUME switch at the rear of the player to
ON.
To cancel repeat play, press PLAY MODE
until “A˜B” disappears from the display.
2Press =or +to choose a track.
The track number and the playing order
appear.
3Press REPEAT/ENTER to program the
track.
4Repeat steps 2 and 3 to program the
remaining tracks.
5Press ^.
“RMS” stops flashing and the tracks you
have chosen play in the order you
specified.
If you press p, the program will be erased. To
prevent accidental erasure, set the RESUME
switch at the rear of the player to ON.
To cancel RMS play, press PLAY MODE until
“RMS” disappears from the display.
To check t he program
During programming:
Press REPEAT/ENTER before step 5.
During RMS play:
Press PLAY MODE repeatedly until
“RMS” flashes, then press REPEAT/
ENTER.
Each time you press REPEAT/ENTER, the
track number and the playing order appear in
the order you specified.
Note
• If you program another track after the 22nd
track, the first track programed is cleared and
the new track is programed instead.
Using other functions
To m inimize skipping (ESP2)
The ESP (Electronic Shock Protection)
function minimize skipping by using a buffer
memory that stores music data and plays it
back in the event of a shock.
The new ESP2(ESP Squared) system uses a
new DSP (Digital Signal Processor) which can
read and store music data more efficiently,
providing a level of continuous skip
protection not found in traditional buffer
memory units. This decreases the frequency
of sound skipping and the need to utilize the
buffer memory. Use this function when
listening in a car or while walking.*
* Although ESP2provides excellent protection
against skipping, it will not prevent skipping
while jogging or running.
Press ESP.
The ESP indication appears.
To release the ESP function, press ESP again.
Notes
• Playing may stop when the player gets a strong
shock even with the ESP function on.
• You may hear a noise or sound skip when:
— listening to a dirty or scratched CD,
— listening to an audio test CD or,
— the player receives continuous shock.
• Sound may drop for a while if you press ESP
during play.
• When you use an optical digital connecting
cord, the ESP function will be disabled.
To enjoy m ore pow erf ul bass sound
(Sound f unct ion)
You can enjoy a powerful bass-boosted sound.
Press SOUND to select “MB (Mega Bass)” or
“GRV (Groove).” “GRV” is more effective.
Note
• If the sound is distorted when emphasizing
bass, turn down the volume.
Playing only the t racks
you w ant (INTRO PGM Play)
You can choose and play your favorite tracks
by scanning through the beginning of each
track in a CD.
1During play, press PLAY MODE
repeatedly until “INTRO PGM” flashes.
2Press ^to start scanning.
The player plays about the first 15
seconds of each track and “INTRO PGM”
flashes faster.
3Press REPEAT/ENTER while the track
you want is playing. To skip the track,
press +or just wait for the next track.
After you have gone through the CD,
“INTRO PGM” stops flashing and the tracks
you have chosen play automatically.
To finish programing before going through
the whole CD, press ^. The selected tracks
will be played.
If you press p, the program will be erased.
To prevent accidental erasure, set the
RESUME switch at the rear of the player to
ON.
To cancel INTRO PGM play, press PLAY
MODE repeatedly until the play mode
indication disappears from the display.
Playing tracks in random
order (Shuff le Play)
You can play the tracks in a CD in random
order.
During play, press PLAY MODE repeatedly
until “SHUF” appears.
The tracks play in random order.
To cancel shuffle play, press PLAY MODE
repeatedly until the play mode indication
disappears from the display.
Note
• During shuffle play, you cannot return to
previous tracks by pressing =.
Playing tracks in the order
you w ant (RM S play)
You can program up to 22 tracks to play in
any order you choose.
1During play, press PLAY MODE
repeatedly until “RMS*” flashes.
*RMS = Random Music Sensor
Flashing
Flashing
Playing order
Track number Flashing
Not these ways
*AMS = Automatic Music Sensor
**These operations are possible during both
play and pause.
If you press REPEAT/ENTER on the player to
display “ ”, you can locate the tracks
continuously in the following order:
• When using +: next track nnext track
...... last track nfirst track nsecond track
......
• When using =: previous track n
previous track ...... first track nlast track
......
To rem ove t he CD
Remove the CD while pressing the pivot.
Notes on controlling the volume w ith
the remote control
Set the VOL (volume) control on the remote
control to the maximum. Then adjust the
volume on the player to the level that you
want to be the maximum volume of the
remote control.
Notes on display
• When you press ^or ((when RESUME
is set to OFF), the total number of tracks in
the CD and the total playing time appear for
about 2 seconds.
• During play, the track number and the
elapsed playing time of the current track
appear.
• During pause, the elapsed playing time
flashes in the display.
• Between tracks, the time to the beginning of
the next track will appear with the “–”
indication.
Notes on handling CDs
• To keep the CD clean, handle it by its edge.
Do not touch the surface.
• Do not stick paper or tape onto the CD.
• Do not expose the CD to direct sunlight or
heat sources such as hot air ducts. Do not
leave the CD in a car parked under direct
sunlight.
To
Pause (main unit
only)
Resume play after
pause (main unit
only)
Find the beginning
of the current track
(AMS*)
Find the beginning
of previous tracks
(AMS)
Find the beginning
of the next track
(AMS)
Find the beginning
of succeeding tracks
(AMS)
Go forward quickly
Go backwards
quickly
Headphones
PLAY M ODE
=/+
REPEAT/
ENTER
PLAY M ODE
+
REPEAT/
ENTER
^
PLAY M ODE
^
=/+
ESP
Label side up
2Fit the CD to the pivot.
3Close the lid.
PLAY M ODE REPEAT/
ENTER
Press
^
^
=once**
=repeatedly**
+once**
+repeatedly**
Hold down +**
Hold down =.**
Flashing
Flashing
Light up
Light up
SOUND
Continue to the reverse side m
Downloaded from: https://www.usersmanualguide.com/

On dry and rechargeable batteries
This player is designed so that it cannot charge
any other rechargeable batteries or dry batteries
for safety reasons.
Rechargeable bat teries NH-DM 2AA/NC-DM AA
Other rechargeable batt eries or dry bat t eries
When you replace the rechargeable batteries
with new ones, make sure to use the NH-
DM2AA/NC-DMAA rechargeable batteries.
• Do not throw the batteries into fire.
• Do not carry the batteries with coins or other
metallic objects. It can generate heat if the
positive and negative terminals of the battery
are accidentally contacted by a metallic object.
• Do not mix rechargeable batteries with dry
batteries.
On the player
• Keep the lens on the player clean and do not
touch it. If you do so, the lens may be
damaged and the player will not operate
properly.
• Do not put any heavy object on top of the
player. The player and the CD may be
damaged.
• Do not leave the player in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or sand, moisture, rain,
mechanical shock, unleveled surface, or in a car
with its windows closed.
• If the player causes interference to the radio or
television reception, turn off the player or
move it away from the radio or television.
• Do not wrap the player in a cloth or blanket
during use as it may cause malfunction or
serious accidents.
On headphones/earphones
Road safety
Do not use headphones/earphones while
driving, cycling, or operating any motorized
vehicle. It may create a traffic hazard and is
illegal in some areas. It can also be potentially
dangerous to play your headsets at high volume
while walking, especially at pedestrian crossings.
You should exercise extreme caution or
discontinue use in potentially hazardous
situations.
Preventing hearing damage
Avoid using headphones/earphones at high
volume. Hearing experts advise against
continuous, loud and extended play. If you
experience a ringing in your ears, reduce volume
or discontinue use.
Caring for others
Keep the volume at a moderate level. This will
allow you to hear outside sounds and to be
considerate to the people around you.
M aintenance
To clean t he casing
Use a soft cloth slightly moistened in water or a
mild detergent solution. Do not use alcohol,
benzine or thinner.
Troubleshoot ing
Should any problem persist after you have made
these checks, consult your nearest Sony dealer.
The CD does not play or “no dlSC”
appears in t he display t hough a CD
is placed in t he player.
mThe CD is dirty or defective.
mInsert the CD with the label side up.
mMoisture condensation has occurred.
Leave the player aside for several hours
until the moisture evaporates.
mThe lens is dirty.
mClose the lid of the player and the battery
compartment firmly.
mMake sure the batteries are inserted
correctly.
mConnect the AC power adaptor to a wall
outlet securely.
When you press ^, “00” appears in
the display f or a m oment, and
disappears. The CD does not play.
mRechargeable battery or dry batteries are
used up. Charge the rechargeable battery
or replace dry batteries with new ones.
3Connect the AC power adaptor.
The indication “CHG” lights up. Charge
for about 4 hours.
(If the battery has been already charged,
“CHG“ and flash. )
4When fully charged, “CHG” disappears.
Disconnect the AC power adaptor.
To t ake out the rechargeable
batt eries
Take out the batteries in the proper way as
illustrated inside the lid or shown below.
When t o charge t he rechargeable
batt eries
When the rechargeable batteries become
weak, indication appears in the display.
If the “Lo ba ” appears in the display,
charge the rechargeable batteries, because the
batteries are used up.
To keep the original battery capacity for a
long time, recharge the batteries when the
batteries are used up (discharged).
When carrying t he rechargeable
batt ery
Make sure to use the supplied battery
carrying case (D-E565 only) or optional
battery carrying case (supplied with the
rechargeable battery).
If you carry the rechargeable battery with a
metal object, short circuit, smoke or fire may
occur.
Notes
• Charging time varies depending on how the
rechargeable battery is used.
• If the battery is new or has not been used for a
long time, it may not be charged completely
until you charge and discharge it several times.
• If the battery life becomes shorter by about
half, replace it with Sony NH-DM2AA/NC-
DMAA rechargeable battery. Do not use any
other rechargeable battery.
Using dry batteries
Insert the batteries properly in the same way
as the rechargeable batteries.
1Disconnect the AC power adaptor and
open the lid of the battery compartment.
2Insert two LR6 (size AA) alkaline
batteries by matching the ‘and ’to the
diagram inside the battery compartment
and close the lid.
Note
• Do not use manganese batteries for this player.
To t ake out the dry batt eries
Take out the batteries properly in the same
way as the rechargeable batteries.
DC IN 4.5 V
AC pow er adapt or
to a wall outlet
Polarit y of t he plug
(rear)
LINE IN or
REC IN
Stereo system,
casset t e recorder,
radio casset te
recorder, etc.
Lef t (w hit e)
Right (red)
LINE OUT
(OPTICAL)
MiniDisc recorder
DAT deck, et c.
OPTICAL
(DIGITAL) IN*
LINE OUT
(OPTICAL)
Opt ical digit al
connecting cord
POC-5B
(not supplied)
(rear)
(rear)
Stereo miniplug Micro plug
Playing a CD in a car
You can use your player in a car by
connecting it to the car cassette deck.
You cannot use the car mount plate for this
player.
When you use the player in a car, install it
securely in a location which does not interfere
your driving.
To connect your player to a car cassette deck,
you need the following accessories:
• Car connecting pack
• Car battery cord
or,
• Car battery cord with car connecting pack
Refer to the instruction manual of each
accessory for details.
Notes
• Do not put the player on the dashboard.
• Do not leave the player in a car parked under
sunlight.
• Use a Sony car connecting pack for reducing
noise.
• Use only the car battery cord listed in the
optional accessories. If you use any other car
battery cord, smoke, fire or malfunction may
occur.
Sw itched ignition function
(w hen using the car battery cord)
With this feature, your player stops
automatically when you turn off the engine of
the car. (This function is not possible with
some cars depending on the model).
Using the remote control
For the cust om ers supplied w it h t he
rem ote control:
You can use the remote control as the wired
remote control.
* Automatic Music Sensor
** When you are not using the remote control,
slide HOLD in the direction of the arrow to
prevent any accidental operations.
To unlock, slide HOLD back.
Note
• Use only the supplied remote control. You
cannot operate this player with the remote
control supplied with other models
zPow er Sources
Using rechargeable
batteries
Charge the rechargeable batteries before
using them for the first time.
Use the NH-DM2AA or NC-DMAA
rechargeable batteries for this player. You
cannot use any other rechargeable batteries.
1Open the lid of the battery compartment.
2Insert two rechargeable batteries by
matching the ‘and ’to the diagram
inside the battery compartment and close
the lid.
Connecting cord
RK-G129HG
When t o replace the dry bat t eries
When the battery becomes weak,
indication appears in the display. If the
batteries are used up, “Lo ba ” appears in
the display. Replace all the batteries with new
ones.
Notes
• Do not charge the dry batteries.
• Do not mix new batteries with old ones.
• Do not use different types of batteries together.
• When the batteries are not to be used for a long
time, remove them.
• If the battery leakage occurs, wipe off any
deposit in the battery compartment, and install
new batteries.
Batt ery lif e (approx. hours) (EIAJ* )
Battery life varies depending on how the
player is used.
When using ESP function
off on
Two NH-DM2AA 12 11
(charged for
about 4 hours**)
Two NC-DMAA 7 6
(charged for
about 4 hours**)
Two Sony alkaline 20 18
batteries LR6SG
*Measured value by the standard of EIAJ
(Electronic Industries Association of Japan)
(When you use the player on a flat and stable
place; When you do not use the optical digital
connecting cord)
**Charging time varies depending on how the
rechargeable battery is used.
How to attach the bat t ery
compart m ent lid
If the battery compartment lid is detached by
an accidental drop, excessive force, etc.,
attach it as illustrated in the numbered order.
zAdditional Inf ormation
Precaut ions
On safety
• Should any solid objects or liquid fall into the
player, unplug it and have it checked by
qualified personnel before operating it any
further.
• Do not put any foreign objects in the DC IN
4.5 V (external power input) jack.
On pow er sources
• When you are not using the player for a long
time, disconnect all power sources from the
player.
On the AC pow er adapt or
• Use only the supplied AC power adaptor. If
your player is not supplied with it, use AC-
E45HG AC power adaptor. Do not use any
other AC power adaptor.
• To unplug the AC power adaptor from the
wall outlet, grasp the adaptor itself, do not pull
its cord.
No sound, or noise is heard.
mConnect the plugs firmly.
mPlugs are dirty. Clean the plugs with a dry
soft cloth periodically.
“Hl dc ln” appears in the display.
mUse only the supplied AC power adaptor
or AC power adaptor AC-E45HG (not
supplied).
mUse only the car battery cord listed in the
optional accessories.
“Hold”
appears in t he display w hen
you press a but t on.
mThe buttons are locked. Slide HOLD back.
“Lo ba ”
appears in t he display
w hen you press a button.
mThe rechargeable batteries are used up
completely. Connect the AC power
adaptor and charge the batteries.
mThe dry batteries are use up. Replace them
with new ones.
The batt ery lif e is short .
mManganese batteries are used. Use alkaline
batteries.
mReplace the batteries with new ones.
The volum e is lim it ed to a cert ain
level even if you attem pt to t urn it
up.
mAVLS selector is set to LIMIT. Set it to
NORM.
mThe earphones are connected to the LINE
OUT jack. Connect them to the 2/
REMOTE jack.
During recording w ith opt ical
digital connect ion, the t rack num ber
cannot be recorded correctly.
mRecord the track number again using the
MiniDisc recorder, DAT recorder, etc.
mRecord again according to the procedure
shown in the section “Connecting to other
stereo equipment.”
Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output
is the value measured at a distance of 200
mm from the objective lens surface on the
optical pick-up block with 7 mm aperture. )
Error correction
Sony Super Strategy Cross Interleave Reed
Solomon Code
D-A conversion
1-bit quartz time-axis control
Frequency response
20 - 20,000 Hz +1
–2 dB (measured by EIAJ CP-
307)
Output (at 4.5 V input level)
Headphones (stereo minijack)
Approx. 15 mW + approx. 15 mW
at 16 ohms
Line output (stereo minijack)
Output level 0.7 V rms at 47 kilohms
Recommended load impedance over 10
kilohms
Optical digital output (optical output connector)
Output level: –21 - –15 dBm
Wavelength: 630 - 690 nm at peak level
General
Pow er requirements
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
• Two Sony NH-DM2AA rechargeable
batteries: 2.4 V DC
Two Sony NC-DMAA rechargeable
batteries: 2.4 V DC
• Two LR6 (size AA) batteries: 3 V DC
• AC power adaptor (DC IN 4.5 V jack):
U2 model: 120 V, 60 Hz
• Sony DCC-E245 car battery cord for use on
car battery: 4.5 V DC
Dimensions (w / h/ d) (w ithout projecting parts
and controls)
Approx. 131.8 ×23.9 ×142.0 mm
(5 1⁄4×31⁄32 ×5 5⁄8in.)
M ass (w ithout rechargeable batteries)
Approx. 200 g (7.0 oz)
Operating temperature
5°C - 35°C (41°F - 95°F)
Supplied accessories
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
D-E561
AC power adaptor (1)
Headphones (1)
D-E565
AC power adaptor (1)
Headphones with remote control (1)
Rechargeable batteries (2)
Battery carrying case (1)
Design and specifications are subject to change
without notice.
For US customers
AC power adaptor supplied is not intended to be
serviced. Should the AC power adaptor cease to
function in its intended manner, during the
warranty period, the adaptor should be returned
to your nearest Sony Service Center or Sony
Authorized Repair Center for replacement, or
after warranty period, it should be discarded.
Opt ional accessories
Car connecting pack CPA-9
Car battery cord with car connecting pack
DCC-E26CP
Car battery cord DCC-E245
Active speaker system SRS-A21
Rechargeable battery NH-DM2AA,
NC-DMAA (2P)
Connecting cord RK-G129HG, RK-G136HG
Optical digital connecting cord POC-5B, POC-
10B, POC-15B, POC-5AB, POC-10AB, POC-15AB
AC power adaptor AC-E45HG
Stereo headphones MDR-35, MDR-E848LP*
* For the customers supplied with the
headphones with remote control:
When connecting optional headphones to
the supplied remote control, use only
headphones with stereo miniplugs. You
cannot use headphones with micro plugs.
Your dealer may not handle some of the above
listed accessories. Please ask the dealer for
detailed information about the accessories in
your country.
To lock the but t ons
You can lock your player against any
accidental operations.
You can still operate the player with the
remote control.
Slide HOLD in the direction of the arrow.
When you press any button, “Hold” appears in
the display and you cannot operate the player.
To unlock, slide HOLD back.
To protect your hearing (AVLS)
The AVLS (Automatic Volume Limiter
System) function keeps down the maximum
volume to protect your ears.
Set AVLS to LIMIT.
The AVLS indication appears.
Note
• If you use the SOUND function and the AVLS
function at the same time, sound may be
distorted. If this happens, turn down the
volume.
To resum e playing from the point
you st opped t he CD (Resum e Play)
Normally, every time you stop and play,
playing starts from the beginning of the CD.
The resume play function, however, lets you
listen to from the point at which you last
turned off the player.
Set RESUME to ON.
To cancel resume play, set RESUME to OFF.
Notes
• Even if RESUME is set to ON, playing starts
from the beginning when you open the lid.
• The resume point may be inaccurate by about
30 seconds.
To t urn off t he beep
You can turn off the beep that sounds as you
operate your player.
Disconnect the power source (AC power
adaptor, rechargeable battery or alkaline
batteries). While you press and hold down p,
connect the power source again. To make the
beep sound again, disconnect the power
source, and then connect it without pressing
p.
Connecting to other
stereo equipment
You can listen to the CD through other stereo
equipment or record a CD on a cassette tape or
a MiniDisc. Refer to the instruction manual of
the other equipment for details. Before making
connections, turn off each piece of equipment.
Using t he connect ing cord
Note
• When you use a connecting cord, the SOUND
function will be disabled.
Using t he optical digital
connecting cord
*If the OPTICAL (DIGITAL) IN jack is square-
shaped, use the POC-5AB optical digital
connecting cord instead.
Notes on connecting to other stereo
equipment
• Before you play the CD, turn down the volume
of the connected equipment so as not to
damage the connected speakers.
• The beep sound is not output from the LINE
OUT (OPTICAL) jack.
• When you connect other equipment to the
LINE OUT (OPTICAL) jack of this player,
adjust the volume on the connected equipment.
• When you record a CD on a cassette tape using
a tape recorder that has the blank search
function, release the ESP function. If the ESP
function is on, the blank search function does
not work.
• Use the AC power adaptor for recording. If
you use the rechargeable batteries or dry
batteries as a power source, batteries may
become weak during recording.
Recording w it h opt ical digital
connection
Record a CD on a MiniDisc, DAT, etc., according
to the following procedure.
1Press ^on the player to start play.
2Press ^again to pause.
3Press =/+to select the track you want to
record.
4Press r(record) on the MiniDisc recorder,
DAT recorder, etc.
5Press ^on the player to release pause.
Notes
• Connect the optical digital connecting cord
while the player is in stop mode.
• If you record without pausing the player, some
CD may have problem with recording the first
track number correctly.
• The SOUND function works on the output
from the 2/REMOTE jack, but does not work
on that from the LINE OUT (OPTICAL) jack.
• When use an optical digital connecting cord,
the ESP function will be disabled.
p(st op)
Remote control
HOLD* *
=(AM S* /
search)
((play)•
+(AM S* /
search) VOL (volume)
Headphones
Downloaded from: https://www.usersmanualguide.com/

This file has been downloaded from:
www.UsersManualGuide.com
User Manual and User Guide for many equipments like mobile phones, photo cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction manual, manual owner, manual owner's, manual guide,
manual operation, operating manual, user's manual, operating instructions, manual operators, manual operator, manual product,
documentation manual, user maintenance, brochure, user reference, pdf manual
Downloaded from: https://www.usersmanualguide.com/