Sony MEXDV2200 - DVD/SACD/CD Receiver User manual

Operating Instructions
4-115-195-11 (1)
MEX-DV2200
©2008 Sony Corporation
GB
Multi Disc Player

2
Warning
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
CAUTION
The use of optical instruments with this product
will increase eye hazard. As the laser beam used
in this CD/DVD player is harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel only.
On safety
• Comply with the traffic laws in your country.
• For your safety, the monitor connected to the
FRONT VIDEO OUT turns off automatically
when the parking brake is not applied.
Warning if your car’s ignition has no
ACC position
Be sure to set the Auto Off function
(page 46).
The unit will shut off completely and
automatically in the set time after the unit is
turned off, which prevents battery drain.
If you do not set the Auto Off function, press
and hold (OFF) until the display disappears
each time you turn the ignition off.
To cancel the demonstration (DEMO) display,
see page 47.
After resetting the unit, if you fail to set the
initial speaker setup correctly due to time out
or a mistake, the settings can be reconfigured
in other menus. To set the speaker connection
status, see page 40. To set the listening
position, see page 38.
This label is located on the bottom of the
chassis.
Preventing an accident
Pictures and karaoke function are available
only after you park the car and set the parking
brake.
If the car starts moving during video playback
or karaoke mode, pictures from the FRONT
VIDEO OUT automatically disappear after
displaying the following caution.
The monitor connected to the REAR VIDEO
OUT is active while the car is in motion.
The pictures on the screen are turned off and
the karaoke mode is deactivated, but audio
source can be heard.
Do not operate the unit or watch the monitor
while driving.
Video blocked for your
safety.
Karaoke function blocked.

3

4
Table of Contents
Welcome ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Playable discs and symbols used in this
manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Location and function of controls . . . . . . . . . .10
Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Card remote commander RM-X169 . . . . . .12
Getting Started
Installing the unit and an optional
monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Resetting the unit. . . . . . . . . . . . . . . . . . 14
Performing initial setup . . . . . . . . . . . . . 14
Preparing the card remote
commander. . . . . . . . . . . . . . . . . . . . . . . 15
Detaching the front panel . . . . . . . . . . . 15
Attaching the front panel. . . . . . . . . . 15
Basic Operations
Playing video discs . . . . . . . . . . . . . . . . 16
Playing audio discs . . . . . . . . . . . . . . . . 18
Listening to the radio. . . . . . . . . . . . . . . 20
Enjoying Surround Sound
Creating an ideal field for multi-channel
sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Advanced Operations — Discs
Playing DivX®/JPEG files . . . . . . . . . . . . . . . .22
DivX®video playback. . . . . . . . . . . . . . . . .22
JPEG image playback . . . . . . . . . . . . . . . . .22
Using PBC functions — Playback control. . . .23
Using play mode menu. . . . . . . . . . . . . . . . . . . 23
Viewing time/text information of the disc . . . .25
Configuring audio settings . . . . . . . . . . . . . . . .26
Changing the audio language/format. . . . . . 26
Checking the program format . . . . . . . . . . .26
Adjusting the audio output level
— DVD level. . . . . . . . . . . . . . . . . . . . . . . .27
Magnifying pictures . . . . . . . . . . . . . . . . . . . . . 27
Adjusting the picture quality
— Picture EQ . . . . . . . . . . . . . . . . . . . . . . . . . 28
Customizing the picture quality . . . . . . . . . 28
Locking discs — Parental control . . . . . . . . . . 29
Activating parental control . . . . . . . . . . . . . 29
Changing the area and its movie rating
level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Repeat and shuffle play . . . . . . . . . . . . . . . . . . 30
Direct search play . . . . . . . . . . . . . . . . . . . . . . 31
Multi-channel output of 2-channel sources
— Pro Logic II. . . . . . . . . . . . . . . . . . . . . . . . . 32
Enjoying karaoke. . . . . . . . . . . . . . . . . . . . . . . 33
Listing up tracks/images/video files
— Quick-BrowZer. . . . . . . . . . . . . . . . . . . . . . 34
Selecting a track/image/video file. . . . . . . . 34
Selecting a file type. . . . . . . . . . . . . . . . . . . 34
Viewing audio disc information . . . . . . . . . . . 34
Configuring playback settings for Super Audio
CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Selecting a playback layer . . . . . . . . . . . . . 35
Selecting the sound quality. . . . . . . . . . . . . 36
Advanced Operations — Radio
Storing and receiving stations . . . . . . . . . . . . . 36
Storing automatically — BTM . . . . . . . . . . 36
Storing manually. . . . . . . . . . . . . . . . . . . . . 36
Receiving stored stations . . . . . . . . . . . . . . 36
Sound Adjustment
Adjusting the sound characteristics
— SOUND . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Enjoying sophisticated sound functions
— X-DSP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Creating a virtual center speaker
— CSO . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Optimizing sound for the listening position
— Intelligent Time Alignment . . . . . . . . . . 38
Precisely calibrating the listening position
— Intelligent Time Alignment Tune . . . . . 38
Customizing the equalizer curve
— EQ7 Tune. . . . . . . . . . . . . . . . . . . . . . . . 39
Speaker configuration and volume setup . . . . 40

5
For installation and connections, see the
supplied installation/connections manual.
Settings
Visual setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Basic operation of visual setup . . . . . . . . . . 41
Language setup for display or
soundtrack . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Display setup. . . . . . . . . . . . . . . . . . . . . . . . 42
Custom setup. . . . . . . . . . . . . . . . . . . . . . . . 43
Audio setup . . . . . . . . . . . . . . . . . . . . . . . . . 44
Resetting all settings . . . . . . . . . . . . . . . . . . 45
System setup . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Basic operation of system setup . . . . . . . . . 45
Setting the clock . . . . . . . . . . . . . . . . . . . . . 50
Using Optional Equipment
Auxiliary equipment . . . . . . . . . . . . . . . . . . . . 50
CD changer . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Rotary commander RM-X4S. . . . . . . . . . . . . . 52
Additional Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Notes on discs . . . . . . . . . . . . . . . . . . . . . . . 53
Playback order of MP3/WMA/JPEG/DivX®
files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
About MP3 files . . . . . . . . . . . . . . . . . . . . . 54
About WMA files . . . . . . . . . . . . . . . . . . . . 54
About JPEG files . . . . . . . . . . . . . . . . . . . . 54
About DivX®files . . . . . . . . . . . . . . . . . . . 54
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Removing the unit . . . . . . . . . . . . . . . . . . . . . . 55
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 56
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . 57
Error displays/Messages . . . . . . . . . . . . . . . 58
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Language code/area code list. . . . . . . . . . . . . . 61
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

6
Welcome !
Thank you for purchasing this Sony Multi Disc
Player. Before operating this unit, read this
manual thoroughly and retain it for future
reference.
Features
Follow the page reference for details.
*1 Depending on track length and recorded sampling
rate.
*2 Unavailable when another optional device is
connected to the BUS CONTROL IN terminal.
DVD, VCD, Super Audio CD, CD playback
tpage 8
Compatible with various disc formats.
2000MP3, 2000WMA
Can play up to 2,000 tracks*1recorded on a
disc in MP3/WMA format.
Multi-disc resume playback
tpage 43
Stores the point where playback is stopped for
up to 5 discs and can resume DVD VIDEO/
VCD/DivX playback even after the disc is
ejected.
For surround sound such as Dolby Digital,
Dolby Pro Logic II, DTS surround, multi-
channel of Super Audio CD, etc., and allows for
the 5.1-channel sound system by connecting an
amplifier and speakers.
tpage 32
Produces 5 full-bandwidth output channels
from 2-channel sources, using an advanced,
high-purity matrix surround decoder.
tpage 37
Sony’s new sound engine creates an ideal in-car
sound field with digital signal processing.
tpage 37
Creates a virtual center speaker and simulates
multi-channel sound field without a center
speaker.
tpage 38
Changes the localization of the sound by
delaying the sound output from each speaker,
and provides the feeling of being in the center
of the sound field, wherever you sit in the car.
tpage 37, 39
7 preset equalizer curves, which can be further
customized by tuning 7 different bands.
tpage 28
Picture tone selectable from preset settings
according to the car’s interior/ambient light.
tpage 33
You can connect a microphone (not supplied)
and enjoy karaoke.
tpage 50
Allows connection of a portable audio device
(analog connection).
tpage 50
The BUS AUDIO IN/AUX AUDIO IN
terminals*2on the rear allow connection and
audio output of an auxiliary device, such as
portable audio device (analog connection),
hideaway navigation device, TV tuner box, etc.

7
Copyrights
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents, other intellectual property
rights owned by Macrovision Corporation, and
other rights owners. Use of this copyright
protection technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly
is prohibited.
Manufactured under license
under U.S. Patent #'s:
5,451,942; 5,956,674;
5,974,380; 5,978,762; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS
and DTS Digital Surround are registered
trademarks and the DTS logos and Symbol are
trademarks of DTS, Inc. © 1996-2007 DTS, Inc.
All Rights Reserved.
“DVD VIDEO,” “DVD-R,” “DVD-RW,”
“DVD+R,” and “DVD+RW” are trademarks.
“DivX” and “DivX Certified” are
registered trademarks or trademarks
of DivX, Inc.
THIS PRODUCT IS LICENSED UNDER THE
MPEG-4 VISUAL PATENT PORTFOLIO
LICENSE FOR THE PERSONAL AND
NONCOMMERCIAL USE OF A CONSUMER
FOR DECODING MPEG-4 VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL AND NON-COMMERCIAL
ACTIVITY AND/OR WAS OBTAINED FROM
A VIDEO PROVIDER LICENSED BY MPEG
LA TO PROVIDE MPEG-4 VIDEO. NO
LICENSE IS GRANTED OR SHALL BE
IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION INCLUDING
THAT RELATING TO PROMOTIONAL,
INTERNAL AND COMMERCIAL USES AND
LICENSING MAY BE OBTAINED FROM
MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM
Manufactured under license
from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the
double-D symbol are trademarks of Dolby
Laboratories.
Windows Media, and the
Windows logo are trademarks
or registered trademarks of
Microsoft Corporation in the
United States and/or other countries.
This product is protected by certain intellectual
property rights of Microsoft Corporation. Use or
distribution of such technology outside of this
product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.

8
Playable discs and symbols used in this manual
This unit can play various video/audio discs.
The following chart helps you to check if a disc is supported by this unit, as well as what functions are
available for a given disc type.
*1 Audio files can also be stored. For details, see page 9.
*2 Video/image files can also be stored. For details, see page 9.
Note
“DVD” may be used in this manual as a general term for DVD VIDEOs, DVD-Rs/DVD-RWs, and DVD+Rs/
DVD+RWs.
Disc symbol in manual Disc format Disc logo
VIDEO
DVD VIDEO
DVD-R*1
DVD-R DL*1
(Video mode/VR mode)
DVD-RW*1
(Video mode/VR mode)
DVD+R*1
DVD+R DL*1
DVD+RW*1
Video CD
(Ver. 1.0/1.1/2.0)
AUDIO
Super Audio CD
Audio CD
CD-ROM*2
CD-R*2
CD-RW*2

9
The following chart shows the supported compression formats, their file types, and the disc types on
which those files can be stored.
Available functions differ depending on the format, regardless of disc type. The format symbols below
appear next to the description of functions available for that format.
Tip
For details on compression formats, see page 54.
Unsupported discs
The following discs cannot be played on this unit.
•8cm(31/4in) discs
• 12 cm (4 3/4in) discs utilizing only the inner 8 cm (3 1/4in) data portion (the rest is transparent)
• CD-ROM containing files other than MP3/WMA/JPEG/DivX
•CD-G
•Photo-CD
• VSD (Video Single Disc)
• DVD-ROM containing files other than MP3/WMA/JPEG/DivX
•DVD-RAM
•DVD-Audio
• Active-Audio (Data)
• SVCD (Super Video CD)
•CDV
• Discs created in Packet Write format
Note
Even compatible discs may not be playable on this unit, depending on their recorded condition.
Region code
The region system is used to protect software copyrights.
The region code is located on the bottom of the unit, and only DVDs
labeled with an identical region code can be played on this unit.
DVDs labeled can also be played.
If you try to play any other DVD, the message “Playback prohibited
by region code.” will appear on the monitor screen. Depending on
the DVD, no region code may be labeled even though playing the
DVD is prohibited by area restrictions.
Format symbol in manual File type Storable disc type
MP3 audio file
DATA DVDs
DVD-ROM
DVD-R
DVD-R DL
DVD-RW
DVD+R
DVD+R DL
DVD+RW
DATA CDs
CD-ROM
CD-R
CD-RW
WMA audio file
JPEG image file
DivX®video file
MULTI DISC PLAYER
DC : 12V NEGATIVE GROUND
SERIAL NO.
CLASS 1
LASER PRODUCT
Region code
ALL

10
Location and function of controls
Main unit
Front panel removed
OFF
SOURCE
MODE
SEEK
SEEK
DSPL
SCRLSETUP
OPEN
ALBUMREP SHUF
312 456
AUX
P
U
S
H
S
O
U
N
D
/
E
N
T
E
R
1
q;9
2
qa qg
qd
4 65 783
qfqs
RESET
q
j
q
k
q
h

11
Refer to the pages listed for details.
Instructions in this manual generally describe the
controls on the card remote commander. You can
also use the controls on the main unit if they have
the same or similar names to those on the card
remote commander.
AOFF button page 14, 16, 18, 23
To power off/stop the source (press); shut off
completely (press and hold).
B(Back)/DSPL (Display) button
page 25, 50
To return to the previous display/change
display items.
CSOURCE button page 14, 15, 20, 36,
51
To power on; change the source (Radio/Disc/
AUX)*1.
Dm(Microphone) button page 33
To activate the karaoke mode.
EControl dial/SOUND/ENTER button
page 14, 27, 33, 34, 36, 39, 40, 45, 50,
51
To adjust the volume/adjust a setting (rotate);
open the sound menu/apply a setting (press).
FReceptor for the card remote
commander
GDisplay window
HOPEN button page 15, 16, 17, 18
ISEEK +/– buttons page 17, 19, 20, 22
Disc:
To skip a chapter/track/scene/file (press);
reverse/fast-forward disc (press and hold
momentarily); reverse/fast-forward track
(press and hold).*2
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
JMODE button page 20, 36, 51
To select the radio band (FM/AM); select an
auxiliary device.*1
K(Browse) button page 34
To enter the Quick-BrowZer mode.*3
LSETUP button page 27, 35, 36, 39, 40,
45, 50, 51
To open the system setup menu.
MNumber buttons
Disc:
(1): bREP page 16, 17, 30, 52
(2): SHUF B page 16, 17, 30, 52
(3)/(4): ALBUM –/+ (V/v) page 16, 17,
19, 22, 51
To skip an album/move the cursor
(press); skip albums or folder
continuously (press and hold).*4
(6): u(play/pause) page 16, 17, 18,
19, 22
To start/pause playback.
Radio:
To receive stored stations (press); store
stations (press and hold).
NSCRL (Scroll) button
To scroll the display item.
OAUX input jack page 50
To connect a portable audio device.
PRESET button page 14
QZ (eject) button page 17, 18
To eject the disc.
RDisc slot page 16, 18
To insert the disc.
*1 While a CD changer is connected, “CDC” appears
on the display when (SOURCE) is pressed. You
can switch the CD changer by pressing (MODE) if
several CD changers are connected.
*2 Operation differs depending on the disc (page 17,
19).
*3 When a Super Audio CD/CD/MP3/WMA/JPEG/
DivX is played.
*4 If the changer is connected, operation is different
(page 51).

12
Card remote commander RM-X169
Refer to the pages listed for details.
Remove the insulation film before use (page 15).
AOFF button page 14, 16, 18, 23
To power off/stop the source (press); shut off
completely (press and hold).
BSOUND button page 33, 37
To open the sound menu.
CVISUAL SETUP button page 23, 26,
27, 28, 29, 31, 32, 35, 38, 41
To open the play mode/visual setup menu.
DSYSTEM SETUP button page 27, 35,
36, 39, 40, 45, 50, 51
To open the system setup menu.
E(Back)/O(Return) button page 23,
24, 29, 35, 38, 41
To return to the previous display; return to
the menu on a VCD*1.
qd
1
2
3
4
5
6
7
8
9
qf
qg
qh
qk
ql
qj
q;
qa
qs

13
FNumber buttons page 16, 17, 23, 24,
29, 31, 36
Disc:
To locate a title/chapter/track.
Radio:
To receive stored stations (press); store
stations (press and hold).
GCLEAR button page 29, 32
To delete an entered number.
HDSPL (Display) button page 25, 50
To change display items.
IPLII (Pro Logic II) button page 32
To select a Dolby Pro Logic II mode.
JATT (Attenuate) button
To attenuate the sound (to cancel, press
again).
Ku(Play/Pause) button page 16, 17,
18, 19, 22
To start/pause playback.
L.m/M> buttons page 17, 19,
20, 22
Disc:
To skip a chapter/track/scene/file (press);
reverse/fast-forward disc (press and hold
momentarily); reverse/fast-forward track
(press and hold).*2
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
MDVD playback setting buttons
(AUDIO): page 17, 26
To change the audio language/format.
(For VCD/CD/MP3/WMA, to change the
audio channel.)
(SUBTITLE): page 17
To change the subtitle language.
(ANGLE): page 17
To change the viewing angle.
(TOP MENU): page 17
To open the top menu on a DVD.
(MENU): page 17
To open the menu on a disc.
N(Browse)/CAT button page 34
To enter the Quick-BrowZer mode*3(the
CAT button does not work on this model).
O</M/m/,(Cursor)/ENTER buttons
To move the cursor and apply a setting.
PSRC (Source) button page 20, 36, 51
To power on; change the source (Radio/Disc/
AUX)*4.
QMODE button page 20, 36, 51
To select the radio band (FM/AM); select an
auxiliary device*4.
RVOL (Volume) +/– buttons
To adjust the volume.
Sm(Microphone) button page 33
To activate the karaoke mode.
*1 When playing with PBC function.
*2 Operation differs depending on the disc (page 17,
19).
*3 When a Super Audio CD/CD/MP3/WMA/JPEG/
DivX is played.
*4 While a CD changer is connected, “CDC” appears
on the display when (SOURCE) is pressed. You
can switch the CD changer by pressing (MODE) if
several CD changers are connected.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the main unit is pressed, or a
disc is inserted to activate the unit first.

14
Getting Started
Installing the unit and an
optional monitor
Firstly, install and connect the unit and an
optional monitor.
This unit can be operated using the displays that
appear on the unit and/or the optional monitor.
Note that this manual includes instructions
concerning displays on both unit and/or optional
monitor.
For details, see the supplied installation/
connections manual.
Note
Be sure to install the optional monitor safely, and in a
place where it does not obstruct the driver’s view.
Resetting the unit
Before operating the unit for the first time, or
after replacing the car battery or changing the
connections, you must reset the unit.
Detach the front panel (page 15) and press the
RESET button (page 10) with a pointed object,
such as a ball-point pen.
Note
Pressing the RESET button will erase the clock setting
and some stored contents.
Performing initial setup
After resetting, the display for initial speaker
setup appears.
Be sure to set correctly following the procedure
below to enjoy the various sound functions of
this unit.
To skip the initial setup, press (OFF)/
(SOURCE), or insert a disc.
Note
The initial setup display automatically changes to the
center speaker setup if no operation is performed for
30 seconds.
During setup procedure, it is canceled if no operation
is performed for 15 seconds.
1Press the control dial in the initial
setup display.
2Rotate the control dial to set the
center speaker connection status,
then press it.
Select “C ON” if the center speaker is
connected, or select “C OFF” if not.
3Rotate the control dial to set the
subwoofer connection status, then
press it.
Select “SUB ON” if the subwoofer is
connected, or select “SUB OFF” if not.
Unit
Optional monitor
OFF SOURCE
Control dial

15
4Rotate the control dial to select your
listening position, then press it.
Select “FRONT L” if your listening position
is front left, or select “FRONT R” if front
right.
The clock display appears when the setting is
complete.
This setting can then be further configured in
setup or the sound menu.
For details on setting the speaker connection
status, see “Speaker configuration and volume
setup” on page 40. For details on setting the
listening position, see “Optimizing sound for the
listening position — Intelligent Time
Alignment” on page 38.
Note
If you set to “C ON” without connecting the center
speaker, vocal sound is not output, and if you set to
“SUB ON” without connecting the subwoofer, bass
sound is not output.
With the card remote commander
Press M/minstead of rotating the control dial, press
(ENTER) instead of pressing the control dial.
Preparing the card remote
commander
Remove the insulation film.
Tip
For how to replace the battery, see page 54.
Detaching the front panel
You can detach the front panel of this unit to
prevent theft.
Caution alarm
If you turn the ignition switch to the OFF
position without detaching the front panel, the
caution alarm will sound for a few seconds.
The alarm will only sound if the built-in
amplifier is used.
1Press (OPEN) while the unit is off.
The front panel is flipped down.
2Slide the front panel to the right, then
gently pull out the left end of the front
panel.
Notes
•Do not drop or put excessive pressure on the front
panel and display window.
•Do not subject the front panel to heat/high
temperature or moisture. Avoid leaving it in a parked
car or on a dashboard/rear tray.
Attaching the front panel
Place the hole Aof the front panel onto the
spindle Bon the unit, then lightly push the left
side in.
Press (SOURCE) on the main unit (or insert a
disc) to operate the unit.
Note
Do not put anything on the inner surface of the front
panel.
SOURCE OPEN
1
2
c
A
B

16
Basic Operations
Playing video discs
Depending on the disc, some operations may be different or restricted.
Refer to the operating instructions supplied with your disc.
To stop playback
Press (OFF).
1Turn on your monitor, then select the input source on your monitor
corresponding to this unit.
2Press (OPEN) on the main unit.
3Insert the disc (label side up).
4Close the front panel.
Playback starts automatically.
If playback does not start automatically, press u.
5If the DVD menu appears, press (1)(b)/(2)(B)/(3)(V)/(4)(v) to move
the cursor, then press (6) (u) to confirm.
With the card remote commander, press the </M/m/,/number buttons to move the cursor,
then press (ENTER) to confirm.
</M/m/,
ENTER
u
OFF
u
b/B/V/v
OFF OPENZ
Number
buttons

17
To eject the disc
1Press (OPEN) on the main unit.
2Press Z(rear of front panel).
About the DVD menu
A DVD is divided into several sections, which make up a picture or music feature. These sections are
called “titles.” When you play a DVD that contains several titles, you can select a desired title using the
DVD’s top menu. For DVDs that allow you to select items such as subtitle/sound language(s), select
these items using the DVD menu.
Other playback operations
*1 Unavailable depending on the disc.
*2 When the 4-digit input prompt appears, input the language code (page 61) for the desired language.
To Press
pause/resume play after pause u
skip a chapter/track/scene/file .m/M>
reverse/fast-forward disc and hold .m/M> momentarily; and then
repeatedly to switch the speed (×2 t×12 t×120 t
×2…)
cancel reverse/fast-forward u
show the DVD menu*1Remote: (TOP MENU) or (MENU)
select items in the DVD menu*1Main unit: (1)(b)/(2)(B)/(3)(V)/(4)(v) to move the
cursor, then press (6) (u) to confirm
Remote: </M/m/,/number buttons to move the cursor,
then press (ENTER) to confirm
change audio language/format/channel
(page 26)*1
Remote: (AUDIO) repeatedly until the desired item appears
turn off/change the subtitle language*1Remote: (SUBTITLE) repeatedly until the desired item
appears*2
change the viewing angle*1Remote: (ANGLE) repeatedly until the desired angle number
appears
.m/M>
uSUBTITLE
ANGLE
MENU
</M/m/,
ENTER
AUDIO
TOP MENU
u
b/B/V/v
.m/M>
Number
buttons

18
Playing audio discs
Depending on the disc, some operations may be different or restricted.
Refer to the operating instructions supplied with your disc.
To stop playback
Press (OFF).
To eject the disc
1Press (OPEN) on the main unit.
2Press Z(rear of front panel).
1Press (OPEN) on the main unit.
2Insert the disc (label side up).
3Close the front panel.
Playback starts automatically.
If playback does not start automatically, press u.
u
OFF
u
OFF OPENZ

19
Other playback operations
*When an MP3/WMA is played.
To Press
pause/resume play after pause u
skip a track .m (<)/M> (,)
reverse/fast-forward track and hold .m/M>
skip an album* Main unit: (3) (ALBUM –)/(4) (ALBUM +)
Remote: M/m
skip albums continuously* Main unit: and hold (3) (ALBUM –)/(4) (ALBUM +)
Remote: and hold M/m
</M/m/,
.m/M>
u
u
ALBUM
/ .m/M>

20
Listening to the radio
Tip
For details on other radio functions, see “Advanced Operations — Radio” on page 36.
With the card remote commander
Use (SRC) instead of (SOURCE), and .m/M> instead of (SEEK) –/+.
1Press (SOURCE) repeatedly until “TUNER” appears.
2Press (MODE) repeatedly until the desired band (FM1, FM2, FM3,
AM1 or AM2) appears.
3Perform tuning.
To tune automatically
Press (SEEK) –/+.
Scanning stops when the unit receives a station. Repeat this procedure until the desired station
is received.
To tune manually
Press and hold (SEEK) –/+ to locate the approximate frequency, then press (SEEK) –/+
repeatedly to fine adjust to the desired frequency.
.m/M>
MODE
SRC
MODE
SOURCE
SEEK
/
BA ARadio band/Function
BFrequency