Sony Dream machine icf-c707 User manual

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

English

WARNING

To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or

moisture.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with newspapers,

tablecloths, curtains, etc. And do not place

lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do

not expose this apparatus to dripping or

splashing, and do not place objects filled with

liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space,

such as a bookcase or built-in cabinet.

Do not expose the batteries (battery pack or

batteries installed) to excessive heat such as

sunshine, fire or the like for a long time.

As the main plug is used to disconnect the unit

from the mains, connect the unit to an easily

accessible AC outlet. Should you notice an

abnormality in the unit, disconnect the main

plug from the AC outlet immediately.

The unit is not disconnected from the AC

power source (mains) as long as it is connected

to the wall outlet, even if the unit itself has been

turned off.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate

this equipment.

The nameplate and important information

concerning safety are located on the bottom

exterior.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same type.

NOTE

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and

on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment

and receiver.

— Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV

technician for help.

WARNING



Replace the battery for the clock backup with

a Sony CR2032 lithium battery. Use of

another battery may present a risk of fire or

explosion.



Battery may explode if mistreated. Do not

recharge, disassemble or dispose of in fire.



Dispose of the used battery promptly. Keep

away from children.

Important Safety

Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the

polarized or grounding-type plug. A

polarized plug has two blades with one

wider than the other. A grounding type plug

has two blades and a third grounding prong.

The wide blade or the third prong are

provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete

outlet.

10)Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified

by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

13)Unplug this apparatus during lightning

storms or when unused for long periods of

time.

14)Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is

damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does

not operate normally, or has been dropped.

Features



Dual alarm FM/AM synthesized clock radio



Nature Sound (Sea Waves, Birds, Rain,

Brook, Under the Sea)



Temperature display (Centigrade/Fahrenheit)

–15°C – 50°C (5°F – 122°F)



Built-in audio cable for Digital Music Player



10 Station Presets (5 FM/5 AM)



Various types of alarms - radio, buzzer and

Nature Sounds (5)



Automatic time set: when you plug the clock

in for the first time, the current time will be

shown in the display



Automatic Daylight Savings Time Set/

Summer time adjustment



100 year calendar and DATE/TIME ZONE

button to display year, month and date



Brightness Control (High/Low/Off)



No Power No Problem alarm system to keep

the clock and the alarm operating during a

power interruption with a CR2032 battery

installed



Extendable Snooze system - Snooze time can

be set from 10 to 60 minutes



Progressive Alarm Speed (buzzer only)

Connecting the

antenna

To connect the AM loop

antenna

The shape and the length of the antenna is

designed to receive AM signals. Do not

dismantle or roll up the antenna.

1Remove only the loop part from the

plastic stand.

2Set up the AM loop antenna.

3Connect the cords to the AM antenna

terminals.

Cord (A) or cord (B) can be connected

either way round.

Only insert up

to here.

Insert the cord while

pushing down the

terminal clamp.

4Make sure the AM loop antenna is

connected firmly by pulling softly.

Adjusting the AM loop antenna

Find a place and an orientation that provides

good reception.



Do not place the AM loop antenna near the

unit or other AV equipment, as noise may

result.

Tip

Adjust the direction of the AM loop antenna for

best AM broadcast sound.

About the backup

battery

To maintain accurate time, this unit includes an

internal CR2032 battery as a backup power

source in the event of a power interruption.

Note for customers in

Canada

The clock is preset at the factory, and its

memory is powered by the preinstalled Sony

CR2032 battery. If the “AM 12:00” appears on

the display when the unit is connected to AC

outlet for the first time, the battery may be

weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part

of the product, and is covered by the warranty.

You are required to show “Note for customers

in Canada” (in this instruction) to a Sony dealer

in order to validate the warranty for this

product.

Knowing when to replace

the battery

When the battery becomes weak, “” will

appear in the display.

If a power interruption occurs while the battery

is weak, the current time and alarm will be

initialized.

Replace the battery with a Sony CR2032 lithium

battery. Use of another battery may cause a fire

or explosion.

Installing and replacing the

backup battery

1Keep the AC plug connected to the AC

outlet, remove the screw that secures

the battery compartment at the bottom

of the unit using a screwdriver, and

pull the battery compartment marked

PULL OPEN. (See fig. -)

2Insert a new battery in the battery

holder with the side facing up.

To remove the battery from the battery

compartment, push it out from the side

marked PUSH. (See fig. -)

3Insert the battery compartment back

into the unit and secure it with the

screw.

(See fig. -)

4When you are replacing the battery,

press any of the following buttons:

RADIO BAND, AUDIO IN, or

NATURE SOUND / PRESET to turn

“” off in the display.

Note

When you replace the battery, do not

disconnect the AC plug from AC outlet.

Otherwise, the 100 year calendar, current time,

alarm and station presets will be initialized.

Setting the clock for

the first time

This unit is preset to current EST (Eastern

Standard Time) at the factory, and is powered

by a backup battery. All you need to do the first

time is just plug it in and select your time zone.

1Plug in the unit.

“year” (about 4 seconds) “month and

date” (about 4 seconds) “the current EST

(Eastern Standard Time)” appears in the

display in turn.

2Press and hold DATE/TIME ZONE for

at least 2 seconds.

Area number “2” flashes in the display.

3Press TIME SET + or –repeatedly to

select the time zone as follows:

Area number Time zone

1 Atlantic standard Time

(default setting)

Eastern standard Time

3 Central standard Time

4 Mountain standard

Time

5 Pacific standard Time

6 Yukon standard Time

7 Hawaiian standard Time

4Press DATE/TIME ZONE to set.

Notes



Though the clock is correctly set at the

factory, discrepancies may arise during

transport or storage. If necessary, set the

clock to the correct time by referring to

“Setting the clock.”



While setting the time zone, you must

perform each step within 65 seconds, or the

time zone setting mode will be cancelled.

When daylight saving time

(summer time) begins

This model automatically adjusts for daylight

saving time (summer time).

“ ” is displayed from the beginning of daylight

saving time (summer time), and disappears at

the end of daylight saving time (summer time)

automatically.



Daylight saving time (summer time) begins

at: 2:00 AM on the second Sunday of March.



Standard time begins at: 2:00 AM on the first

Sunday of November.

To cancel Automatic DST/Summer

Time adjustment during the daylight

saving time (summer time) period

Automatic DST/Summer Time adjustment can

be canceled.

Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS at the same time for

at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show

that Automatic DST/Summer Time adjustment

has been canceled. The display returns to the

clock.

Notes



Time change of Automatic DST/Summer

Time adjustment (see above) is subject to

variations in circumstances and laws of each

country/region. Cancel Automatic DST/

Summer Time adjustment and set the DST

display manually as necessary. Customers

living in a country/region that does not use

daylight saving time (summer time) must

cancel Automatic DST/Summer Time

adjustment before using the unit.



To activate Automatic DST/Summer Time

adjustment again, press and hold DISPLAY/

CLOCK and SNOOZE / BRIGHTNESS at the

same time for at least 2 seconds.

“ ” and “On” appear in the display to show

that Automatic DST/Summer Time

adjustment has been activated. The display

returns to the clock.

Setting the clock

1Plug in the unit.

2Press and hold DISPLAY/CLOCK for at

least 2 seconds.

The year starts to flash in the display.

3Press TIME SET + or –repeatedly to

set the year.

4Press DISPLAY/CLOCK.

5Repeat steps 3and 4to set the month,

day, hour and minute, and then press

DISPLAY/CLOCK.

The seconds start incrementing from zero.

Notes



While setting the clock, you must perform

each step within 65 seconds, or the clock

setting mode will be cancelled.



When pressing any of the rear buttons, hold

the unit firmly to prevent slippage.

To display the year and date

Press DATE/TIME ZONE once for the year, and

press again for the date.

After a while, the display will change back to

the current time automatically.

Setting the brightness

of the display

Three levels of brightness are available by

pressing SNOOZE / BRIGHTNESS.

Note

When the alarm is sounding, the brightness

function cannot be used.

4-180-721-21(1) To set the alarm

1Press and hold ALARM ON/OFF A or

Bfor a few seconds.

2Press TIME SET + or –to set the

desired hour, and press ALARM ON/

OFF A or B.

3Press TIME SET + or –to set the

desired minute, and press ALARM ON/

OFF A or B.

4Press TIME SET + or –to set the

desired alarm period (“WEEKDAY,”

“WEEKEND” or everyday*), and press

ALARM ON/OFF A or B.

* In the case of everyday, both

“WEEKDAY” and “WEEKEND” are

displayed.

5Press TIME SET + or –to set the

desired alarm mode (“NATURE

SOUND,” “RADIO,” or “BUZZER”),

and press ALARM ON/OFF A or B.

You can choose one of 3 settings: “NATURE

SOUND,” “RADIO,” or “BUZZER.” Set the

alarm mode as follows:

– NATURE SOUND: see “Setting the

nature sound alarm.”

– RADIO: see “Setting the radio alarm.”

– BUZZER: see “Setting the buzzer

alarm.”

Setting the Nature Sound alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“NATURE SOUND” alarm mode, and

press ALARM ON/OFF A or B.

“NATURE SOUND” appears in the display.

3Press TIME SET + or –to select the

NATURE SOUND / PRESET 1to 5,

and press ALARM ON/OFF A or B.

4Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

5Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

Nature sound will sound at the set time.

Setting the radio alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“RADIO” alarm mode, and press

ALARM ON/OFF A or B.

“RADIO” appears in the display.

3Press TIME SET + or –to select the

AM band, FM band or the last station,

and press ALARM ON/OFF A or B.

If you select the last station, jump to step 5.

4Press TIME SET + or –to select the

station, and press ALARM ON/OFF A

or B.

5Press TIME SET + or –to adjust the

volume, and press ALARM ON/OFF A

or B.

The setting is entered.

6Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The radio will turn on at the set time.

Setting the Buzzer alarm

1Perform steps 1to 5in “To set the

alarm.”

2Press TIME SET + or –to select

“BUZZER” alarm mode, and press

ALARM ON/OFF A or B.

The setting is entered.

3Press ALARM ON/OFF A or B. “” or

“” appears in the display after about

4 seconds.

The buzzer will sound at the set time.

When the alarm setting is completed, the alarm

time setting is displayed.

When both ALARM “” and ALARM “” are

turned on, you can switch the ALARM Aand

ALARM Bdisplay by pressing DISPLAY/

CLOCK.

Notes



When you use the radio alarm, the timed

alarm sounds with the last broadcasting

station tuned to before the power went off.

When you set the radio alarm, select the

desired broadcasting station before turning

the power off.



The ALARM “” (or “”) indicator flashes

in the display when the alarm sounds.



If a second alarm sounds during a first (or

the SNOOZE function is active), the second

alarm takes priority.



The alarm function works as usual at the

beginning and end day of daylight saving

time (summer time). While Automatic DST/

Summer Time adjustment is set, as a result, if

the alarm is set at a time skipped when the

daylight saving time (summer time) begins,

the alarm is skipped, or if the alarm is set at a

time overlapped when the daylight saving

time (summer time) ends, the alarm sounds

twice.



If the same alarm time is set for both alarms

(ALARM A and B), ALARM A takes priority.

Playing the radio

Manual tuning

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press TUNING + or –to tune in to a

desired frequency.

3Adjust the volume using VOL + or –.

Tuning in to a station

The unit automatically scans AM or FM

stations.

1Press RADIO BAND to turn on the

radio to select the AM or FM band.

2Press and hold TUNING + or –.

+: scans upward through the frequency

bands.

–: scans downwards through the frequency

bands.

Scanning starts from the currently-tuned

frequency. When a station is received,

scanning stops.

3Adjust the volume using VOL +

or –.

Preset tuning

You can preset 5 stations for FM and 5 stations

for AM.

Presetting a station

1Follow steps 1and 2in “Manual

tuning” to tune the frequency you wish

to preset.

2Hold down the desired NATURE

SOUND / PRESET 1to 5button until

you hear two beeps.

Example: The following display appears

when you preset FM 105.7 MHz to preset

number 3 for FM.



The display shows the frequency for a few

seconds and then changes back to the

current time.

To change the preset station, tune into the

desired station and hold down the NATURE

SOUND / PRESET 1to 5button until you

hear two beeps.

To preset another station, repeat these steps.

Note

If you try to store another station with the same

preset number, the previously stored station

will be replaced.

Tuning in to a preset station

1Press RADIO BAND to turn on the

radio and select the AM or FM band.

2Press NATURE SOUND / PRESET 1to

5where the desired station is stored.

3Adjust the volume using VOL + or –.

Improving the

reception

FM: Extend the FM wire antenna fully to

increase reception sensitivity.

AM: Connect the supplied AM loop antenna to

the unit. Rotate the antenna horizontally

for optimum reception.

Note on radio reception

Keep digital music players or mobile phones

away from the AM loop antenna or the FM

antenna, as this may lead to reception

interference.

Selecting a Nature

Sound

This unit includes 5 types of Nature Sounds:

(Sea Waves, Birds, Rain, Brook and Under the

Sea.)

You can choose any one of these by pressing the

corresponding button.

Icons Sound type

Sea Waves

Birds

Rain

Brook

Under the Sea

Note

When other functions are in use, Nature Sound

is not available.

Setting the alarm

The dual alarm function allows you to set two

alarm programs (ALARM ON/OFF A and

ALARM ON/OFF B).

The alarm time can be set for each program

and the alarm sound is selectable from

“NATURE SOUND,” “RADIO,” or “BUZZER.”

Notes



Before setting the alarm, make sure to set the

clock. (See “Setting the clock”)



The factory setting alarm time is “PM 12:00.”



To set the radio alarm, first preset your

favourite station. (See “Presetting a station”)



While setting the alarm, you must perform

each step within 65 seconds, or the alarm

setting mode will be cancelled.

To confirm an alarm time setting

Turn off the ALARM ON/OFF “” or “”

indicator in the display, and press the ALARM

ON/OFF A or Bbutton again.

You can confirm the alarm time by pressing

TIME SET + or –after the alarm time is set.

To change an alarm setting

There are two ways to set the alarm:

To change all alarm settings

Set the alarm again.

To change an alarm time only

When setting the alarm (ALARM “” or

ALARM “” appears), this function is

available.

Press and hold TIME SET + for at least

2 seconds to move the alarm time forwards.

Press and hold TIME SET – for at least

2 seconds to move the alarm time back. When

you release the button, the changed time will be

displayed for about 2 seconds. To change the

alarm time, press TIME SET + or –within these

2 seconds, otherwise the setting change will be

fixed as displayed.

To doze for a few more minutes

Press SNOOZE / BRIGHTNESS.

The sound turns off but will automatically

come on again after about 10 minutes.

You can change the snooze time by pressing

SNOOZE / BRIGHTNESS repeatedly within

4 seconds.

The maximum the snooze time is 60 minutes.

To stop the alarm

Press OFF ALARM RESET to turn off the

alarm.

The alarm will sound again at the same time

depending on the next day setting.

To deactivate the alarm

Press ALARM ON/OFF A or Bto turn off the

ALARM “” or “” indicator in the display.

Note on the alarm in the event of a power

interruption

In the event of a power interruption, the alarm

will work until the internal battery is worn out.

However, certain functions may be affected as

follows:



The backlight will not light up.



If the alarm mode is set to Nature Sound or

radio, it will change to BUZZER

automatically.



If a power interruption occurs while the

alarm is sounding, the alarm will stop.



If OFF ALARM RESET is not pressed, the

alarm will sound for about 5 minutes.



If “” appears in the display, the alarm will

not sound in the event of power interruption.

Replace the battery if “” appears.



The snooze function will not work.



During a power interruption, the alarm will

sound at the set time only once.

Setting the sleep

timer

You can fall asleep to the “NATURE SOUND,”

“RADIO,” or “AUDIO IN” using the built-in

sleep timer that turns off the “NATURE

SOUND,” “RADIO,” or “AUDIO IN”

automatically after a preset duration.

1Press SLEEP while the unit is turned

on.

“SLEEP” appears and the sleep time flashes

in the display.

2Press SLEEP to set the sleep timer

duration.

Each time you press SLEEP, the duration

(in minutes) changes as follows:

90 60 30 15

OFF

The display returns to clock mode for about

4 seconds after you have finished the

duration setting and released SLEEP, and

then the sleep timer starts.

The unit will play for the duration you set,

and then shut off.

Note

Even if the Sleep Timer is set, it cannot turn off

the power of optional components connected to

the AUDIO IN jack of this player.

To turn off the unit before the preset

time

Press OFF ALARM RESET.

To change the sleep timer setting

You can press SLEEP repeatedly to select the

desired sleep timer setting even after the sleep

timer has been activated.

To deactivate the sleep timer

Press SLEEP repeatedly to set the sleep timer to

“OFF” in step 2.

Using the

temperature function

This unit includes an external temperature

sensor, allowing you to monitor ambient

temperature.

The temperature is displayed in Centigrade or

Fahrenheit.

To switch between Centigrade and, Fahrenheit

press and hold the SNOOZE / BRIGHTNESS

and DATE/TIME ZONE buttons for more than

2 seconds.

Notes



In the example, the display shows Centigrade;

however, Fahrenheit can also be displayed.



Do not use in water.



Do not forcefully pull on the external

temperature sensor. Improper use of the

external temperature sensor may cause a

malfunction.



The display temperature and actual

temperature may differ depending on the

usage environment.



Do not place the temperature sensor near the

floor, a heat source such as a radiator or

airduct, or in a place subject to direct

sunlight.

The temperature sensor reading may differ

from actual surrounding temperature.



The operating temperature range is –15 °C

(5 °F) to 50 °C (122 °F).

In the case of lower than –15 °C (5 °F) or

higher than 50 °C (122 °F), the “Lo” or “Hi”

indicator appears.



When plugging in the unit or recovering

from a power interruption, the temperature

display of this unit will flash “--”.

The temperature will be displayed after 20

seconds.

No Power No Problem is a trademark of Sony Corporation.

No Power No Problem est une marque de fabrique de Sony Corporation

Dream Machine is a trademark of Sony Corporation.

Dream Machine est une marque de fabrique de Sony Corporation.

FM/AM Clock Radio

ICF-C707

Operating Instructions

Mode d’emploi (au dos)

FM wire antenna

AC power cord

Built-in audio

cable

The VOL + button has a tactile dot.

Temperature

sensor



CR2032

 

Built-in audio

cable

The built-in audio cable can

be inserted in the slot of the

unit.

To the headphones

jack or line output

jack





Connecting external

equipment

(See fig. )

To listen to sound

1Connect the built-in audio cable with

the stereo-miniplug on the bottom of

the unit to the line output jack or

headphones jack on the optional

component (e.g., portable music

player).

2Press AUDIO IN.

“AUDIO IN” appears in the display.

3Play the optional component

connected to the unit’s built-in audio

cable.

4Adjust the volume using VOL + or –

and the connected component’s

volume.

To return to the radio

Press RADIO BAND.

The frequency is shown in the display.

To stop listening

Press OFF ALARM RESET, and stop playback

on the connected unit.

To turn off the sound from the

optional component

Press OFF ALARM RESET, and then turn off

the optional component.

Notes



Refer also to the connected equipment’s

manual.



Connect the audio cable firmly to prevent a

malfunction.



Keep digital music players away from the

speaker.



If you increase the volume too much, loud

sound may occurs when switching to the

radio.



Confirm the volume when you remove the

connected component from this unit to listen

by headphones. Otherwise, high volume may

affect your hearing.



AUDIO IN cannot be set for the alarm

sound.



When you listen to the radio with external

equipment connected, turn off the connected

equipment to prevent noise. If noise occurs,

even when the equipment is turned off,

disconnect and place the external equipment

away from the unit.

Troubleshooting

Should any problem persist after you have

made the following checks, consult your nearest

Sony dealer.

The clock flashes “AM 12:00”due to a

power interruption.



The battery is low. Replace the battery.

Remove the old battery and install a new one.

The alarm settings do not sound at the

preset alarm time.



Check that alarm “” or alarm “” is

properly set/displayed.

The alarm settings are activated but there

is no sound at the preset alarm time.



Check the alarm volume setting.

When daylight saving time begins, the

clock does not employ the daylight saving

time automatically.



Make sure the clock is set correctly.



Press and hold DISPLAY/CLOCK and

SNOOZE / BRIGHTNESS simultaneously for

at least 2 seconds to activate the Automatic

DST function.

Precautions



Play the unit on the power source specified in

“Specifications.”



To disconnect the power cord (mains lead),

pull it out by the plug, not the cord.



Since a strong magnet is used for the speaker,

keep personal credit cards using magnetic

coding or spring-wound watches away from

the unit to prevent possible damage from the

magnet.



Do not leave the unit in a location near a heat

source such as a radiator or airduct, or in a

place subject to direct sunlight, excessive

dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent

internal heat build-up. Do not place the unit

on a thick pile surface (rug, a blanket, etc.),

or near materials that might block the

ventilation holes (such as a curtain, etc. ).



Should any solid object or liquid fall into the

unit, unplug the unit and have it checked by

qualified personnel before operating it any

further.



To clean the casing, use a soft cloth

dampened with a mild detergent solution.



Never touch the wire of the external FM

antenna during a thunderstorm.

Furthermore, immediately disconnect the

main plug from the wall outlet.

NOTES ON THE LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a

good contact.



Be sure to observe the correct polarity when

installing the battery.



Do not hold the battery with metallic

tweezers, otherwise a short-circuit may

occur.

If you have any questions or problems

concerning your unit, please consult your

nearest Sony dealer.

Specifications

Time display

12-hour system

Radio section

Frequency range

Band Frequency Channel step

FM 87.5 MHz – 108 MHz 0.1 MHz

AM 530 kHz – 1,710 kHz 10 kHz

General

Speaker

Approx. 3.6 cm (1 7/16 inches) dia. 8 Ω

Input

Built-in audio cable with stereo-mini plug

(ø 3.5 mm)

Power output

0.7 W (at 10% harmonic distortion)

Power requirements

120 V AC, 60 Hz

For clock back up: 3V DC, one CR2032 battery

Nature Sound

Sea Waves, Birds, Rain, Brook, Under the Sea

Temperature range

–15 °C – 50 °C (5 °F – 122 °F)

Temperature resolution

1 °C (1 °F)

Dimensions

Approx. 190 mm × 67 mm × 62 mm (w/h/d)

(7 1/2inches × 2 3/4inches × 2 1/2 inches) not

including projecting parts and controls

Mass

Approx. 620 g (1 lb 5.87 oz) including power

supply unit and CR2032 battery

Supplied accessories

AM loop antenna (1)

Design and specifications are subject to change

without notice.

Other manuals for DREAM MACHINE ICF-C707

Table of contents

Other Sony Clock Radio manuals

Sony

Sony ICF-C05iP User manual

Sony

Sony ICF-C713L User manual

Sony

Sony ICF-C723 - Ic Memory Clock Radio User manual

Sony

Sony DREAM MACHINE ICF-CD830 User manual

Sony

Sony XDR-C1DBP User manual

Sony

Sony Dream Machine ICF-C233 User manual

Sony

Sony ICF-CDK70 - Currently Not Available User manual

Sony

Sony Dream Machine ICF-C180 User manual

Sony

Sony Dream Machine ICF-C205 User manual

Sony

Sony ICF-CDK50 User manual

Sony

Sony ICF-C255RC - Auto Time Set Clock Radio User manual

Sony

Sony ICF-C1 User manual

Sony

Sony Dream Machine ICF-CD823L User manual

Sony

Sony Dream Machine ICF-C218 User manual

Sony

Sony ICF-CD855V - Cd Clock Radio User manual

Sony

Sony ICF-CD820 - Cd/am/fm Stereo Clock Radio User manual

Sony

Sony DREAM MACHINE ICF-CD843V User manual

Sony

Sony DREAM MACHINE ICF-C318 User manual

Sony

Sony Dream Machine ICF-C115 User manual

Sony

Sony ICF-CD810 User manual

Sony

Sony ICF-CD837 User manual

Sony

Sony Walkman ICF-CD2000 User manual

Sony

Sony ICF-CS10IP - Clock Radio With Ipod Dock User manual

Sony

Sony ICF-CS10IP User manual

Popular Clock Radio manuals by other brands

Technika

Technika CR-109IDAB Owner's handbook

Philips

Philips AJ130 Specifications

RCA

RCA RP5605R user manual

Electrohome

Electrohome EAAC601 quick start guide

RCA

RCA RP5500i user manual

Aluratek

Aluratek AIRMM02F Instructional manual

Hannlomax

Hannlomax HX-128CR quick start guide

Grundig

Grundig SCN 340 user manual

Emerson

Emerson RET23 quick guide

capello

capello CR2W user guide

Sylvania

Sylvania SKCR2613 Product features

Emerson Research

Emerson Research fYi iC172 owner's manual

Philips

Philips AJ AJ3910 user manual

HMDX

HMDX Cube HX-B440 Instruction manual and warranty information

RCA

RCA RC59i user manual

Curtis

Curtis iMODE IP2604UK Specification sheet

Philips

Philips XP AJ 3380 Instructions for use

AEG

AEG SRC 4325 CD instruction manual

Sony DREAM MACHINE ICF-C707 User manual

Popular Clock Radio manuals by other brands