Sony Cyber-Shot DSC-J10 User manual

DSC-J10 Sony Corporation
SERVICE MANUAL
Revision History
SERVICE NOTE (Check the following note before the service.)
983454411.pdf
2010L29-1
© 2010.12
Published by Sony Techno Create Corporation
Ver. 1.0 2010.12
DIGITAL STILL CAMERA
9-834-544-11
US Model
AEP Model
UK Model
E Model
Chinese Model
Hong Kong Model
Korea Model
Argentine Model
Tourist Model
DSC-J10
Ver. Date History Contents S.M. Rev.
issued
1.0 2010.12 Official Release — —
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
1-2. PRECAUTION ON REPLACING THE LENS
1-3. REGARDING FUSE
Photo: Blue
Internal memory
ON BOARD
Internal memory
ON BOARD
The components identified
by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.

DSC-J10
– 2 –
SPECIFICATIONS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections.Checktheentireboardsurfaceforsoldersplashesand
bridges.
2. Checktheinterboardwiringtoensurethatnowiresare“pinched”
orcontacthigh-wattageresistors.
3. Look for unauthorized replacement parts, particularly transistors,
thatwereinstalledduringapreviousrepair.Pointthemouttothe
customerandrecommendtheirreplacement.
4. Lookforpartswhich,throughfunctioning,showobvioussignsof
deterioration.Pointthemouttothecustomerandrecommendtheir
replacement.
5. ChecktheB+voltagetoseeitisatthevaluesspecified.
6. FlexibleCircuitBoardRepairing
 •Keepthetemperatureofthesolderingironaround350°Cduring
repairing.
 •Donottouchthesolderingirononthesameconductorofthecircuit
board(within3times).
 •Becarefulnottoapplyforceontheconductorwhensolderingor
unsoldering.
UNLEADED SOLDER
Thisunitusesunleadedsolder.
Boardsrequiringuseofunleadedsolderareprintedwiththeleadfree
mark(LF)indicatingthesoldercontainsnolead.
(Caution:Someprintedcircuitboardsmaynotcomeprintedwiththe
leadfreemarkduetotheirparticularsize.)
: LEAD FREE MARK
Becarefultothefollowingpointstosolderorunsolder.
• Setthesolderingirontiptemperatureto350°Capproximately.
 Ifcannotcontroltemperature,solder/unsolderathightemperature
forashorttime.
Caution:Theprinted pattern(copperfoil)maypeelaway if the
heatedtipisappliedfortoolong,sobecareful!
  Unleadedsolder is more viscous(sticky, lessprone to
flow)thanordinarysoldersousecautionnottoletsolder
bridgesoccursuchasonICpins,etc.
• Besuretocontrolsolderingirontipsusedforunleadedsolderand
thoseforleadedsoldersotheyaremanagedseparately.Mixingun-
leadedsolderandleadedsolderwillcausedetachmentphenomenon.
Camera
[System]
Image device: 7.75 mm (1/2.3 type)
color CCD, Primary color filter
Total pixel number of camera:
Approx. 16.4 Megapixels
Effective pixel number of camera:
Approx. 16.1 Megapixels
Lens: 4 × zoom lens
F3.5 (W) - F4.6 (T)
f = 6.18 mm - 24.7 mm (35 mm -
140 mm (35 mm film equivalent))
Scene Selection (10 modes)
White balance: Automatic, Daylight,
Cloudy, Fluorescent 1/2/3,
Incandescent, Flash, One Push
Recording interval for Burst mode:
Approx. 0.95 second
File format:
Still images: JPEG (DCF Ver. 2.0,
Exif Ver. 2.3, MPF Baseline)
compliant
Movies: AVI (Motion JPEG)
Recording media: Internal Memory
(Approx. 4 GB)
1 GBequals 1billion bytes, a
When measuring media capacity,
portion of which is used for system
files.
Available user capacity: Approx.
3.9 GB
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index)
set to Auto):
Approx. 0.2 m to 3.6 m (W)
(7 7/8 inches to 11 feet 9 3/4 inches)
Approx. 0.2 m to 2.8 m (T)
(7 7/8 inches to 9 feet 2 1/4 inches)
[Input and Output connectors]
USB arm: type A (built-in)
USB communication: Hi-Speed USB
(USB 2.0)
Exposure control: Automatic exposure, [LCD screen]
LCD panel: 6.7 cm (2.7 type) TFT drive
Total number of dots: 230,400 (960 ×
240) dots
[Power, general]
Power:
(wall socket) by connecting with
Built-in rechargeable battery
pack: 3.7 V
Supplied from the wall outlet
Power consumption (during
the supplied AC adaptor (AC-
UB10): 5 V
shooting): 1.6 W
Operating temperature: 0 °C to 40 °C
Storage temperature: -20 °C to -60 °C
(-4 °F to +140 °F)
(32 °F to 104 °F)
Dimensions:
93.6 × 59.4 × 17.3 mm
(3 3/4 × 2 3/8 × 1 1/16 inches)
(W/H/D, excluding protrusions)
Mass:
Approx. 126 g (4.4 oz.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
management and/or application
•
•
•
•
PRINT Image Matching III:
Compatible
AC adaptor (AC-UB10)
Power requirements: AC 100 V to
240 V, 50 Hz/60 Hz, 70 mA
Output voltage: DC 5 V, 0.5 A
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: -20 °C to +60 °C
(-4 °F to +140 °F)
Dimensions: Approx. 50 × 22 × 54 mm
(2 × 7/8 × 2 1/4 inches) (W/H/D)
Mass: Approx. 48 g (1.7 oz) (For USA
and Canada models), Approx. 43 g
(1.5 oz) (Except USA and Canada
models)
Design and specifications are subject to
change without notice. ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion occurs if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

DSC-J10
1-1E
1. SERVICE NOTE
1-1. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note1: When replacing the Main Board Assy, erase the data in internal memory of main board before replacement.
Note2: When replacing the Main Board Assy, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
1-2. PRECAUTION ON REPLACING THE LENS
When replacing the lens, write down the Tele Limit Data given on the data sheet of the replacement lens for service.
Execute the J10 Write Zoom Calib Value.
For details of adjusting method, please refer to the Service manual ADJ of DSC-J10 (9-834-544-5[]).
Method for Formatting the Internal Memory
Note: The Tele Limit Data of lens is written only repair parts.
Importing images to a computer (Windows)
“PMB” allows you to easily import images.
For details on “PMB” functions, see the “PMB Help”.
Importing images to a computer without using “PMB”
When the AutoPlay Wizard appears after making a USB connection between the camera
and a computer, click [Open folder to view files] [OK] [DCIM] copy the desired
images to the computer.
Format
Formats the internal memory. Note that formatting permanently erases all data on the
internal memory, and is unrecoverable. Save precious data on a computer, etc.
(Settings) (Internal Memory Tool) [Format] [OK]
Note
Note that formatting permanently erases all data including even protected images.
1. MENU
X
X
X
X
Tele Limit Data
XXXX
1-3. REGARDING FUSE
• MAIN BOARD
Ref. No: F2
Part No: 1-576-415-11
Description: FUSE, MICRO (1608 TYPE) (2A/32V)
F2 F1
Ref. No: F1
Part No: 1-576-415-11
Description: FUSE, MICRO (1608 TYPE) (2A/32V)

DSC-J10
2-1
Link
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
View Position
(ENGLISH)
NOTE:
• -XX,-Xmeanstandardizedparts,sotheymayhavesomedifferencesfromtheoriginalone.
• Itemsmarked“*”arenotstockedsincetheyareseldomrequiredforroutineservice.Some
delayshouldbeanticipatedwhenorderingtheseitems.
• Themechanicalpartswithnoreferencenumberintheexplodedviewsarenotsupplied.
• Duetostandardization,replacementsinthepartslistmaybedifferentfromthepartsspeci-
fiedinthediagramsorthecomponentsusedontheset.
• Abbreviation
AR : Argentine model
CH : Chinese model
HK : Hong Kong model
KR : Korea model
TW : Taiwan model
JE : Tourist model Back View
Bottom View
Right View
Front View
Left View
Top View
ACCESSORIES ASSEMBLYDISCHARGING OF THE CHARGING CAPACITOR
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark 0 or
dottedlinewithmark0arecriticalforsafety.
Replaceonlywithpartnumberspecified.
Lescomposantsidentifiésparunemarque
0sontcritiquespourlasécurité.
Nelesremplacerqueparunepièceportant
lenumérospécifié.
Whenindicatingpartsbyreference
number,pleaseincludetheboardname.
2Front Cover Assy
1Rear Cover Assy
qaMain Board Assy
7USB Holder
5SW Board
8LCD Bracket Assy
qsChassis
6LCD Module
0ST Board
9Optical Unit
3Battery

DSC-J10
2-2
Wrap insulating tape.
NOTE FOR REPAIR
• Makesurethattheflatcableandflexibleboardarenotcrackedof
bentattheterminal.
 Donotinsertthecableinsufficientlynorcrookedly.
• Whenremoveaconnector,donotpullatwire ofconnector.Itis
possiblethatawireissnapped.
• Wheninstallingaconnector,donotpressdownatwireofconnector.
 Itispossiblethatawireissnapped.
• Donotapplyexcessiveloadtothegildedflexibleboard.
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage
when the capacitor is handled by hand. The electric shock
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned
off. Therefore, the remaining voltage must be discharged as
described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end
of a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Cut and remove the part of gilt
which comes off at the point.
(Be careful of that some
pieces of gilt may be left inside)
Make sure to remove
the battery before
Discharging the Capacitor.
ST Board
Note:Note: High-voltage cautionsHigh-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 kΩ/1 W
(Part code: 1-215-869-11)

DSC-J10
2-3
2-1. EXPLODEDVIEWS
2-1-1.OVERALLSECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
DISASSEMBLY
1USBConnectorOpen(1)→ #S1/#S2X2→#S1/#S2X1→#S3/#S4X2
4RemovetheSwitchAssy(4)
5#S6X2→RemovetheCushion(5)
1. Removetonumericalorder(1 to6)intheleftfigure.
Note
DISCHARGINGOFTHECHARGINGCAPACITOR
1 X-2580-781-1 COVER ASSY, FRONT (WHITE)
1 X-2580-782-1 COVER ASSY, FRONT (BLACK)
1 X-2580-783-1 COVER ASSY, FRONT (RED)
1 X-2580-784-1 COVER ASSY, FRONT (ORANGE)
1 X-2580-785-1 COVER ASSY, FRONT (BLUE)
2 X-2580-780-1 COVER ASSY, REAR
3 4-274-007-01 CUSHION (SW)
4 A-1813-385-A SW BOARD (Note2)
5 1-802-984-11 LCD MODULE (Note2)
6 X-2580-786-1 SWITCH ASSY (WHITE)
6 X-2580-787-1 SWITCH ASSY (BLACK)
6 X-2580-788-1 SWITCH ASSY (RED)
6 X-2580-789-1 SWITCH ASSY (ORANGE)
6 X-2580-790-1 SWITCH ASSY (BLUE)
7 4-274-011-01 CUSHION (1)
8 4-274-012-01 CUSHION (2)
0 9 1-756-765-13 BATTERY PACK (SP60BPRA9C)
10 4-274-000-01 LID, BT INNER
#S1 4-273-996-01 SCREW_M_1.4_3_BLK_AB (Note1)
#S2 4-273-997-01 SCREW_M_1.4_3_SVR_AB (Note1)
#S3 4-273-998-01 SCREW_M_1.4_4_BLK_AB (Note1)
#S4 4-273-999-01 SCREW_M_1.4_4_SVR_AB (Note1)
#S6 4-274-006-01 SCREW_TP_1.4_2_SVR_AB
Note1: THECOMBINATIONOFCABINET’SCOLORANDSCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer
to Table 2-1.
Table 2-1
Screw's
Ref. No. (Parts Color.) Cabinet's Color
#S2, #S4 (Silver) WHITE, RED,
ORANGE, BLUE
#S1, #S3 (Black) BLACK
Back View Front View
#S6
Cushion
Caution
Danger of explosion occurs if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Front View
Open
Left View Right View Bottom View
#S3
#S4
#S1
#S2
#S1
#S2
Note2: Refer to “Assembly-1: Handling Method for the Flexible
Boards of the LCD Module and SW Board” when you
assemble.
Note3: These parts are not supplied. Take care that do not damage
them when removing.
2�1
21
#S6
3
3�9
6�5
(Note2)
5�4
(Note2)
46
ns 5
(Note3)
ns
(Note3)
Main Board Section
(See Page 2-4)
2(Claw)
1
#S1
#S2
(Note1)
#S1
#S2
(Note1)
#S3
#S4
(Note1)
4
10
A
B
A
B

DSC-J10
2-4
Ref. No. Part No. Description Ref. No. Part No. Description
2-1-2.MAINBOARDSECTION DISASSEMBLY
1. Removetonumericalorder(7 toqs)intheleftfigure.
51 4-274-001-01 HOLDER, USB
52 4-274-007-01 CUSHION (SW)
53 4-274-004-01 SPRING, USB COVER
54 4-274-003-01 COVER, USB (WHITE) (Note1)
54 4-274-003-11 COVER, USB (BLACK) (Note1)
54 4-274-003-21 COVER, USB (RED) (Note1)
54 4-274-003-31 COVER, USB (ORANGE) (Note1)
54 4-274-003-41 COVER, USB (BLUE) (Note1)
55 4-274-005-01 SPRING, USB JACK
56 A-1813-422-A JACK, USB (WHITE) (Note2)
56 A-1813-423-A JACK, USB (BLACK) (Note2)
56 A-1813-424-A JACK, USB (RED) (Note2)
56 A-1813-425-A JACK, USB (ORANGE) (Note2)
56 A-1813-426-A JACK, USB (BLUE) (Note2)
57 4-274-019-01 PLATE (D), GROUND
58 4-274-009-01 SHAFT (STRAP)
59 A-1813-429-A SPEAKER (Note3)
60 X-2580-791-1 LEVER ASSY, ZOOM (WHITE)
60 X-2580-792-1 LEVER ASSY, ZOOM (BLACK)
60 X-2580-793-1 LEVER ASSY, ZOOM (RED)
60 X-2580-794-1 LEVER ASSY, ZOOM (ORANGE)
60 X-2580-795-1 LEVER ASSY, ZOOM (BLUE)
61 A-1816-072-A ST BOARD
62 X-2580-796-1 BRACKET ASSY, LCD
63 1-856-181-11 OPTICAL UNIT (BE0032)
64 A-1813-408-A CCD BLOCK ASSY
65 4-274-020-01 CHASSIS
66 4-274-016-01 PLATE (A), GROUND
67 4-274-017-01 PLATE (B), GROUND
68 4-274-018-01 PLATE (C), GROUND
69 A-1813-427-A MICROPHONE (Note4)
70 4-274-010-01 PLATE, MICROPHONE GROUND
71 A-1813-428-A MAIN BOARD, COMPLETE
72 4-274-012-01 CUSHION (2)
73 4-274-011-01 CUSHION (1)
0F1 1-576-415-11 FUSE, MICRO (1608 TYPE) (2A/32V)
0F2 1-576-415-11 FUSE, MICRO (1608 TYPE) (2A/32V)
#S2 4-273-997-01 SCREW_M_1.4_3_SVR_AB
#S5 4-274-002-01 SCREW_TP_1.4_3_SVR_AB
#S7 4-274-013-01 SCREW_TP_1.2_3.5_SVR_AB
7#S2X1→#S5X1
Front View
#S5
#S2
Note
Note1: Referto“Assembly-2:AssemblingMethodoftheUSBCover”
whenyouassemble.
Note2: Referto“Assembly-3:AssemblingMethodoftheUSBJack”
whenyouassemble.
Note3: Referto“Assembly-4:RoutingandSolderingMethodofthe
SpeakerLeadWire”whenyouassemble.
Note4: Referto“Assembly-5:SolderingMethodoftheMicrophone
LeadWire”whenyouassemble.
8#S5X2
qaUnsolder(qa-1)→Unsolder(qa-2)→#S5X4
0Unsolder(0)→#S5X4
Back View
#S5
Back View Top View
#S5
Solder
Front View
qa-1
qa-2
#S5
#S5
51 7
54
(Note1)
(Note2)
56
61 0
qa�71
73
72
63 9
64
#S5
(Note3)
#S2
#S5
#S5
52
53
55
70
69
(Note4)
59
58
57
68
67
66
#S7
65 qs
F2 F1
8�62
60
#S5
#S5
11(Solder)
qa-1qa-1
11(Solder)
qa-2qa-2
10(Solder)

DSC-J10
2-5E
Checking supplied accessories.
CD-ROM
- Cyber-shot application software
- “Cyber-shot User Guide”
4-266-075-01
Wrist strap
2-050-981-01
Instruction Manual
・(Only for destination Japanese model)
AC adaptor
(AC-UB10)
01-489-282-21 (US)
01-489-282-31 (CH)
Power cord (mains lead)
(EXCEPT US, CH)
01-836-411-21 (JE)
01-837-421-11 (UK, HK)
01-837-424-11 (TW)
01-837-427-11 (AEP, E)
01-838-951-11 (AR)
01-838-954-11 (KR)
Dedicated USB cable
1-836-378-51
Conversion (2P) Adaptor
01-569-008-12
(E (Latin America))
Conversion (2P) Adaptor
01-569-007-12 (JE)
AC adaptor
(AC-UB10)
01-489-282-61
(EXCEPT US, CH)
∗4-265-841-11 (ENGLISH)
∗4-265-841-21 (
FRENCH)
∗4-265-841-31 ( ITALIAN)
∗4-265-841-41 ( SPANISH )
∗4-265-841-51 (PORTUGUESE)
∗4-265-841-61 (
GERMAN )
∗4-265-841-71 (
DUTCH )
∗4-265-841-81 (
TRADITIONAL CHINESE )
∗4-265-841-91 (
SIMPLIFIED CHINESE )
∗4-265-846-11 (
RUSSIAN )
∗4-265-846-21 (
ARABIC )
∗4-265-846-31 (
PERSIAN )
∗4-265-846-41 (KOREAN)
∗4-265-846-51 (
POLISH )
∗4-265-846-61 (
CZECH )
∗4-265-846-71 ( HUNGARIAN )
∗4-265-846-81 (SLOVAK)
∗4-265-846-91 (SWEDISH)
∗4-265-847-11 (FINNISH)
∗4-265-847-21 (NORWEGIAN)
∗4-265-847-31 (DANISH)
∗4-265-847-41 (THAI)
∗4-265-847-51 (MALAY)
∗4-265-847-61 (TURKISH)
∗4-265-847-71 (GREEK)
∗4-265-847-81 (UKRAINIAN)
∗4-265-847-91 (CROATIAN)
∗4-265-848-11 (ROMANIAN)
∗4-265-848-21 (INDONESIAN)
∗4-265-848-31 (BRAZILIAN PORTUGUESE)
4-266-072-11 (SIMPLIFIED CHINESE)
4-266-073-11 (ENGLISH)
∗ 4-266-073-21 (ENGLISH, SPANISH)
∗ 4-266-073-31 (ENGLISH, FRENCH)
∗ 4-266-073-41 (ENGLISH, RUSSIAN, UKRAINIAN)
 ∗ 4-266-073-51 (ENGLISH, FRENCH, ITALIAN, SPANISH, PORTUGUESE,
GERMAN, DUTCH, TURKISH, GREEK, POLISH, CZECH,
HUNGARIAN, SLOVAK, SWEDISH, FINNISH, NORWEGIAN,
DANISH, CROATIAN, ROMANIAN)
∗ 4-266-073-61 (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE,
INDONESIAN, ARABIC, PERSIAN, THAI)
∗ 4-266-073-71 (ENGLISH, SPANISH, PORTUGUESE)
∗ 4-266-073-81 (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE,
INDONESIAN, ARABIC, PERSIAN)
∗ 4-266-073-91 (ENGLISH, SPANISH, PORTUGUESE, TRADITIONAL CHINESE,
SIMPLIFIED CHINESE, KOREAN)
∗4-266-074-11 (ENGLISH, TRADITIONAL CHINESE, SIMPLIFIED CHINESE)
4-266-074-21 (KOREAN)
∗4-266-074-31 (SPANISH, PORTUGUESE)
∗4-266-074-41 (ENGLISH, ARABIC, PERSIAN)
∗4-266-074-51 (ENGLISH, TRADITIONAL CHINESE)
Cyber-shot User Guide (HTML)
About Cyber-shot User Guide (HTML)
This CD-ROM is provided in HTML.
Therefore, it is suitable for browsing on the PC, but is not suitable for printing.
The printed matter is not supplied.
The following lists part numbers of languages.
The CD-ROM supplied contains all of language version.
英語・韓国語・中国語のみ部品供給可能です。
DSC-J10
User Guide
Use this manual ifyou encounter any problems, or have any questions about the camera.

DSC-J10
3-1E
3. ASSEMBLY
Assembly-2: Assembling Method of the USB Cover
Chassis
USB Cover
USB Cover Spring
Microphone lead wire
Solder
Assembly-5: Soldering Method of the Microphone
Lead Wire
Main Board
Speaker lead wire
Chassis
Main Board
Assembly-4: Routing and Soldering Method of
the Speaker Lead Wire
Route the speaker lead wire as shown below.
Speaker lead wire
Chassis Solder
USB Jack
USB Jack Spring
Chassis
Assembly-3: Assembling Method of the USB Jack
Harness
Assembly-1: Handling Method for the Flexible Boards
of the LCD Module and SW Board
SW Board
Chassis
LCD Module
LCD Bracket Assy

DSC-J10
4-1E
4. BLOCK DIAGRAMS
4-1. OVERALL BLOCK DIAGRAM
D R IVER LEN S C O N
G PIO
D D R 2 64M
x 16BIT
VD &TG
IC X682 16M
M IC R O PH O N E
U SB I/F
STO R AG E I/F
U II/F
38M H z
C O AC H -13S
SEN SO R
AFE
R TC
STR O BE
I/F
AU D IO
12M H z
TI
VSP6244B
SD R AM I/F
I/F
I/F
M O TO R
G PIO
G 2001
D ISPLAY
I/F
SPEAKER
FLASH I/F
3 in 1G PIO
eM M C
U SB I/F
SO N Y C C D
32.768KH z
SensorBoard
STR O BE Board
Flash C harge
R T9595
POWER CIRCUIT
Sam sung 2.7"LM S270G F078