Sony Cyber-shot DSC-TX10 User manual

S ON'Y: 4-26_-636-22(1)
DigitalStillOamera,,nstruct,onManual GBiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiii
Ca,mara fotografia digital /Manual de instrucciones ES
Cgb_r-shot AVCHD H-"lml"

Owner's Record
The model and serial numbers are located on the bottom. Record the serial number in the
space provided below. Refer to these numbers whenever you call your Sony dealer
regarding this product.
Model No. DSC-TX 10
Serial No.
Model No. AC-UB I0/UB I0B
Serial No.
To reduce fire or shock hazard, do not expose the unit to rain or
moisture.
IMPORTANT SAFETYINSTRUCTIONS
-SAVETHESEINSTRUCTIONS
DANGER
TOREDUCETHERISKOFFIREORELECTRIC
SHOCK,CAREFULLYFOLLOWTHESE
INSTRUCTIONS
If the' shape of the phlg does not fit the' pow_'r outlet, us_' an attaclmwnt phlg adaptor of the
proper configuration for the power outlet.
Battery pack
If the batlery pack is mishandled, the halt_'ry pack can burst, cause a fire or ev_.n ch_.mical
burns. Observe the following caulions.
• Do not disassemble.
• Do not crush and do not expose the battery pack to any shock or lkm.-e such as
hammering, dropping or stepping on it.
•Do not short circuit and do not allow metal objects to come into contact with the battery
terminals.
• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a
GB car parked in the sun.
2 • Do not incinerate or dispose of in fir<..

•Donothandledamagedorleakinglithiumionbatteries.
•BesuretochargethebatterypackusingagenuineSonybatterychargeroradevicethat
canchargethebatterypack.
•Keepthebatterypackoutofthereachofsmallchildren.
•Keepthebatterypackdry.
•ReplaceonlywiththesameorequivalenttyperecommendedbySony.
•Disposeofusedbatterypackspromptlyasdescribedintheinstructions.
AC Adaptor
Connect the AC Adaptor to the nearest wall outlet (wall socket).
If some trouble occurs while using the A( Adaptor. immediately shut off the power by
disconnecting the plug from the wall outlet (wall socket).
The power cord (mains lead), if supplied, is designed specifically for use with this camera
only, and should not be used with other electrical equipment.
GBi!!!!!!i!!!!!!
RECYCLING LITHIUM-ION BATTERIES
Lithium-Ion batteries arc lccyclablc.
You can help preserve our environment by returning your used
mchargeable batteries to the collection and recycling location nearest
you.
For morn information regarding recycling of mchargeable batteries.
call toll free
1_800-822-8837. or visit http://www.rbrc.or_
Caution: Do not handle damaged or leaking Lithiumqon batteries.
Battery pack
This device complies with Part 15 of the F(( Rules. Operation is su[_jcct to the following
two conditions:
(1) This device may not cause Imrmful interference, and (2) this device must accept any
interference received, inchlding interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian 1CES4103.
UL is an internationally recognized safety organization.
The UL Mark on the product means it has been UL Listed.
If you have any questions about this product, you may call:
Sony (ustomer Information Center
1-800_222-SONY (7669).
The number below is for the FCC related matters only.
GB
3

Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: DSC-TXI0
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo,
San Diego, (A 92127 U.S.A.
Telephone No.: 858-942-2230
This device complies with Partl 5 of tile FCC Rules. Operation is sut_ject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION
You art.' cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.
Note:
This equipment has been tested and l\mnd to comply with the limits lk_r a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits am designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses. and can radiate radio frequency
energy and. if not installed and used in accordance with tile instructions, may cause
harmful interference to radio communications. However. there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning tile
equipment off and on. tile user is encouraged to try to correct the interference by one or
more of tile following measures:
Reorient or relocate the receiving antenna.
lncrease tile separation between tile equipment and receiver.
Connect tile equipment into an outlet on a circuit different from that to which tile
receiver is connected.
Consult tile dealer or an experienced radio/TV technician for help.
The supplied interface cable must be used with the equipment in oMer to comply with tile
limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
GB
4

Notice for the customers in the countries applying EU Directives
The manufacturer of this product is Sony Uorporation. I-7-1 Konan Minato-ku Tokyo.
108-0075 Japan. The Authorized Representative for EM( and product saf_.ty is Sony
Deutschland GmbH. Hedelfinger Strasse 61. 70327 Stuttgart, Germany. For any service or
guarantee matters please refer to the addr_.sses given in separate service or guarantee
doctlments.
This product has been tested and found compliant with the limits set out in the EMU
Directive l\)r using connection cables shorter than 3 meters (9.8 feet).
Attention
The ek'ctromagnctic fields at the specific fr_'qucncics may influence the picture' and sound
of this unit.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway (fail),
restart the application or disconnect and connect the communication cable (USB, etc.)
again.
Disposal of Old Electrical & Electronic Equipment (Applicable in
the European Union and other European countries with separate
collection systems)
This symbol on the producl or on its packaging indicates thai this producl
shall not be treated as household waste. Instead 0 shall be handed over to
the applicable colleclion point for the recycling of eleclrical and electronic
equipmenl. By ensuring Ihis producl is disposed of correctly, you will help
pre\ enl potential negali\ e consequences for the elp, h-onment and htlman
health, which could otherwise be caused by inappropriate waste handling
of Ihis producl. The recycling of lnalerials will help Io conserve nalural
resources. For mole detailed information about recycling of this product.
please contact your local Civic Office. your household waste disposal service or the shop
where you purchased the product.
GBi!!!!!!i!!!!!!
GB
5

Disposal of waste batteries (applicable in the European Union
and other European countries with separate collection systems)
This sylnbol on the battery or on the packaging indicates that the battery
pro; ided with this product shall not be treated as household waste.
On cerlain batteries this sylnbol might be used in colnbination with a
chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are
added if the battery contains more than 0.0005g{ lnercury or ().O()4c,{ lead.
By ensuring these batteries are disposed of correctly, you will help prevent
potentially negative consequences fl_r the environment and human health which could
otherwise be caused by inappropriate waste handling of the battery. The recycling of the
materials will help to conserve natural resources.
In case of products that l\_r safety, performance or data integrity reasons require a
permanent connection with an incorporated battery, this battery should be replaced by
qualified service stall" only. To ensure that the battery will be treated properly, hand over
the product at end-of-life to the applicable collection point for the recycling of electrical
and electronic equipment.
For all other batteries, please view the section on how to remove the battery from the
product sal'ely.
Hand the battery over to the applicable collection point for the recycling of waste batteries.
For more detailed inl\_rmation about recycling of this product or battery, please contact
your local Civic Office, your household waste disposal service or the shop where you
purchased the product.
A moulded plug complying with BS 1363 is fitted to this equipment fl_r your safety and
convenience.
Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an _ or _?
mark) must be used.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the
fuse cover after you change the fuse. Never use the plug without the fuse cover. If you
should lose the fuse cover, please contact your nearest Sony service station.
GB
6

About water-proof, dust-proof, and shock-proof
performance of the camera
This camera is equipped to be water-proof, dust-proof and shock-proof.
Damage caused from misuse, abuse or failure to properly maintain the camera
is not covered by the limited warranty.
• This camera is water-proof/dust-proof equivalent to IEC60529 IP58. The
camera is operable up to a water depth of 5 m for 60 minutes.
• Do not subject the camera to pressurized water, such as from a tap.
• Do not use in hot springs.
• Use the camera in the recommended operating water temperature range of
10°C to +40°C (14°F to 104°F).
• Conforming to MIL-STD 810F Method 516.5-Shock standards, this product
has passed testing when dropped from a height of 1.5 m above a 5-cm thick
plywood board*.
':'Depending on use conditions and circumstances, no guarantee is made regarding
damage to, malNnction of, or the water-proof perlormance of this camera.
• As lk_r dust-proof/shock-proof performance, there is no guarantee that the
camera will not become scratched or dented.
• Sometimes water-proof perlk_rmance is lost if the camera is subjected to a
strong shock such as from being dropped. We recommend the camera be
inspected at an authorized repair shop for a fee.
• Accessories supplied do not meet water-proof, dust-proof, and shock-proof
specifications.
Notes before using the camera under/near water
• Make sure that no foreign matter such as
sand, hair, or dirt gets inside the battery/
melilory card cover or multi-connector
cover. Even a small amount of foreign
matter may lead to water entering the
callnera.
GBi!!!!!!i!!!!!!
GB
7

• Confirm that the sealing gasket and its
mating surfaces have not become scratched.
Even a small scratch may lead to water
entering the camera. If the sealing gasket or
its mating surfaces become scratched, take
the camera to an authorized repair shop to (_) Sealing gasket
have the sealing gaskel replaced li_)ra fee. @ Surface contacting the
• If dirt or sand gels on the sealing gasket or sealing gasket
its mating surfaces, wipe the area clean with
a soft cloth that will not leave behind any
fibers. Prevent the sealing gasket from becoming scratched by touching it
while charging a battery or using a cable.
• Do not open/close the battery/memory card cover or multi-connector cover
with wet or sandy hands or near water. There is a risk this will lead to sand or
water getting inside. Before opening the cover, perform the procedure
described in "Cleaning afler using the camera under/near water".
• Open the battery/memory card cover and multi-connector cover with the
camera completely dry.
• Always confirm that the battery/memory card cover and multi-connector
cover have been securely locked.
Notes on using the camera under/near water
• The touch panel may bc activated by water sphtshes on the screen icons.
When using the camera under/near water, it is recommended that you hide
the icons by touching _F on the right side of the screen. Touch _ for a few
seconds to display the icons again.
• The touch panel cannot be operated underwater. Use the buttons of the
camera to perform shooting or playback operations.
• Do not subject the camera to shock such as from jumping into water.
• Do not open and close the battery/memory card cover or multi-connector
cover while under/near water.
• Use a separately available housing (Marine Pack) if going more than
5 meters under water.
• This camera sinks in water. Place your hand through the wrist strap to
prevent the camera from sinking.
• Faint, white, circular spots may appear in under-water flash photos due to
reflections oft"of floating objects. This is not a malfunction.
• Select _ (Underwater) in Scene Selection to shoot underwater with less
distortion.
GB• If water drops or other foreign matter is present on the lens, you will be
8 unable to record clear images.

•Donotopenthelenscoverwherethesandiswhirling.
Cleaning after using the camera under/near
water
• Always clean the camera with water after use
within 60 minutes, and do not open the battery/
memory card cover before cleaning is finished.
Sand or water may get inside places where it
cannot be seen. If not rinsed, water-proof
perli)rmance will be degraded.
• Allow the camera to sit in pure water poured into a cleaning bowl for about 5
minutes. Then, gently shake the camera, press each button, slide the zoom
lever or the lens cover inside the water, to clean away any salt, sand or other
matter lodged around the buttons or the lens cover.
• After rinsing, wipe away water drops with a soft cloth. Allow the camera to
dry completely in a shady location with good ventilation. Do not blow dry
with a hair dryer as there is a risk of deformation and/or degraded water-
proof performance.
• Wipe away water drops or dust on the memory card/battery cover or terminal
cover with a soft dry cloth.
• This camera is constructed to drain water. Water will drain from openings
around the ON/OFF (Power) button, zoom lever, and other controls. After
removing from water, place the camera on a dry cloth for a while to allow
water to drain.
• Bubbles may appear when the camera is placed under water. This is not a
malfunction.
• The camera body may become discolored if it comes in contact with
sunscreen or suntan oil. If the camera does come in contact with sunscreen or
suntan oil, quickly wipe it clean.
• Do not allow the camera to sit with salt water inside or on the surface. This
may lead to corrosion or discoloration, and degradation of water-proof
performance.
• To maintain the water-proof performance, we recommend that once a year
you take the camera to your dealer, or to an authorized repair shop, to have
the sealing gasket of the battery/memory card cover, or of the multi-
connector cover replaced for a l)e.
GB
GB
9

For details on advanced operations, please read "Cyber-shot User Guide"
(HTML) on the CD-ROM (supplied) using a computer.
Insert the CD-ROM into the CD-ROM drive.
For Windows users:
(_) Click IUser Guide] -_ [Install].
@ Start "User Guide" from the shortcut on the desktop.
For Macintosh users:
(_ Select the [User Guide] folder and copy [eng] folder stored in [User Guide]
folder to your computer.
@ After copying is complete, double-click "index.html" in [eng] folder.
Camera (1)
Rechargeable battery pack NP-BN1 (l)
Multi-use terminal USB cable (1)
AC Adaptor AC-UB 10/UB 10B (1)
Power cord (mains lead) (not supplied in the USA and Canada) (1)
Paint pen (1)
Wrist strap ( 1)
CD-ROM (1)
Cyber-shot application software
"Cyber-shot User Guide"
• Instruction Manual (this manual) (1)
• Notes on the water-proofing (1)
GB
10

[] Lens
[] _b,- (Playback) button
[] MOVIE (Movie) butv,)n
[] Screen/Touch panel
[] ON/OFF (Power/Charge) button
[] ON/OFF (Power/Charge) lamp
[] Shutter button
[] For shooting: W/T (Zoom) lever
For viewing: O_ (Playback
zoom) lever/_Rl (Index) lever
[] Hook for wrist strap
[] HDMI connector
[] Multi connector (Type3b)
[] Memory card slot
[] Access lamp
[] Battery eject lever
]Connector cover
[] Battery/memory card cover
[] _ (TransfcrJet _M) mark
[] Battery insertion slot
[] Tripod receptacle
• Use a tripod with a screw less
than 5.5 mm (7/32 inches) long.
Otherwise, you cannot firmly
secure tile camera, alld damage to
tile camera may occur.
GBi!!!!!!i!!!!!!
[] Microphone
[] Lens cover
[] Flash
[] Self-timer lamp/Smile Shutter
lamp/AF illuminator G[3
11

Eject lever
1Open the cover.
2Insert the battery pack.
•While pressing Ihe battery eject lever, insert the batlery pack as
illustrated. Make sure that the battery eject lever locks after insertion.
For customers in the USA,
Canada
GB
12
(Mains lead)
h_#,
For customers in countries/regions
other than the USA and Canada
Power/Charge lamp
Lit: Charging
Off: Charging finished
Flash: Charging error

1Open the connector cover and connect the camera and
the AC Adaptor (supplied), using the multi-use terminal
USB cable (supplied).
2Connect the AC Adaptor to the wall outlet (wall socket).
The Porker/Charge hunp lights orange, and charging starts.
• Turn off the camera while charging the battery.
• You can charge the battery pack even when it is parlially charged.
• When the Power/Charge lamp flashes and charging is not finished,
remove and re-insert the battery pack.
GB
• Close the cover securely, so that the yellow mark under the slide lock is bidden.
• When the Pnwer/Charge lamp on the camera does not lit even if the AC Adaptor is
connected to the camera and the wall outlet (wall socket), it indicates that the
charging stops temporarily on standby. The charging stops and enters the standby
status automatically when the temperature is outside of the reconnnended
operating temperature. When the temperature gets back within the appropriate
range, the charging resumes. We recommend charging the battery pack in an
ambient temperature of between 10°C to 30°C (50°F to 86°F).
• Connect the AC Adaptor (supplied) to the nearest wall outlet (wall socket). If any
malfunctions occur while using the AC Adaptor, disconnect the plug fi'nm the wall
nutlet (wall socket) immediately to disconnect the power snurce.
• When charging is finished, disconnect the AC Adaptor fi'om the wall outlet (wall
sncket).
• Be sure to use only genuine Sony brand battery packs, multi-use terminal USB
cable (supplied) and AC Adaptor (supplied).
Charging by connecting to a computer
The battery pack can be charged by connecting the camera to a computer using
a multi-use terminal USB cable.
GB
13

m
• Note the following points when charging via a computer:
If the camera is connected to a laptop computer that is not connected to a power
source, the laptop battery level decreases. Do not charge li)r an extended period
of time.
Do not turn on/off or restart the computer, or wake the computer resume from
sleep mode when a USB connection has been established between the computer
and the camera. The camera may cause a malfunction. Belk_returning nn/off, or
restarting the computer or waking the computer h'om sleep mode, disconnect the
camera alld the computer.
No guarantees are made li)r charging using a custom-built computer nr a
modified computer.
Charging time
The charging time is approximately 210 rain. using the AC Adaptor
(supplied).
• The above charging time applies when charging a fully depleted battery pack at a
temperature of 25°C (77°F). Charging may take longer depending on conditions of
use and circumstances.
Battery life and number of still images you can record
and view
iiiii_!_iiii_!!!_i_ii_ii_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i:]ii_!_iiii_!!!_i_ii_ii_!i_iX_@_iN_i_!?_i_i_iiii_ii_!i_!i_ii_!'ii_!_iiiiN_i_!_!_iNii!N_iijii,!!ii!
Shooting (still images) Approx. 125 min. Approx. 250 images
Viewing (still images) Approx. 190 min. Apprnx. 3800 images
Shooting (movies) Approx. 60 min.
II_NIY2]_
• The above number of still images applies when the battery pack is lillly charged.
The nmnber of still images may decrease depending on the conditions of use.
• The number nf still images that can be recorded is fnr shooting under the following
conditions:
Using Sony "Memory Stick PRO Duo" (Mark2) media (sold separately)
The battery pack is used at an ambient temperature of 25°C (77°F).
• The nmnber liar"Shooting (still images)" is based nn the C1PA standard, and is for
shooting under the IMlowing conditions:
GB (CIPA: Camera & hnaging Products Association)
] 4 [Panel Brightness] is set to 131

Shootingonceevery30seconds.
ThezoomisswitchedalternatelybetweentheWandTends.
-Theflashstrobesonceeverytwotimes.
Thepowerturnsonandnffnnceeverytentimes.
•Thebatterylifefnrmoviesappliesshootingunderthefnllowingconditions:
Moviequality:AVCHDHQ
Whencontinuousshootingendsbecauseofsetlimits(page24),pressthe
MOVIE(Movie)buttonagainandcnntinueshooting.ShootingRmctinussuchas
theznomdonotnperate.
Supplying power
The camera can be suppliud with pmx_er from the wall outlet (wall socket) by
connecting to the AC Adaptor, using the multi-use terminal USB cable
(supplied).
You can import images to a computer without worrying about wearing down
the battery pack by connecting the camera to a computer using the multi-use
terminal USB cable.
GB
• Power cannot be supplied when the battery pack is nnt inserted in the camera.
• Pnwer supply li'om the wall outlet (wall socket) is available only when the camera
is in playback mode or when a connection is made between the camera and a
cnmputer. If the camera is in shooting mode or while you are changing the settings
nfthe camera, power is not supplied even if you make a USB connection using the
multi=use terminal USB cable.
• lfyou connect the camera and a computer using the multi-use terminal USB cable
when the camera is in playback mode, the display nn the camera is changed li'nm
the playback screen to the USB connection screen. Press i_'i (Playback) button to
switch to the playback screen.
GB
15

Ensure the notched corner faces
correctly.
1Open the cover.
2Insert the memory card (sold separately).
•With the notched corner facing as illustrated, insert the mcmery card
until it clicks into place.
3Close the cover securely, so that the yellow mark under
the slide lock is hidden.
• Closing the cover with the battery inserted incerrectly may damage the
camera.
Memory cards that you can use
i iiii
Memory Stick PRO Duo O O (Mark2 only)
AMemory Stick PRO-HG Duo O O
Memory Stick Duo O
SD memory card 0 0 (Class 4 or faster)
BSDHC memory card O O (Class 4 or faster)
SDXC memory card O O (Class 4 or faster)
• In this manual, producls in A are colleclively refizrred (o as "Memory Stick Duo"
media, and products in B are collectively referred lo as SD card.
GB
16

To remove the memory card/battery pack
Memory card: Push the memory card in once.
Battery pack: Slide the battery eject lever. Be sure not to drop the battery pack.
• Never remove the memory card/battery pack when the access lamp (page 11) is lit.
This may cause damage to data in the memory card/internal memory. GB
ON/OFF (Power) Lens cover
| Lower the lens cover.
The camera is turned on. The power hunp lights up only when the camera
starls up.
• You can also lurn on the camera by pressing the ON/OFF (Power)
button.
• It may take time l'or the power to turn on and allow operation.
2 Select a desired language.
3 Select the desired area following the instructions on the
screen, then touch [Next].
4Set [Daylight Savings] or [Summer Time], [Date 8,Time
Format] and [Date & Time], then touch [Next].
• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.
5 Touch [OK]. 6B
17

6Select the desired display color, following the
instructions on the screen, then touch [OK].
7When an tin-Camera Guide] introductory message is
appeared on the screen, touch [OK].
8 Read the waterproof precautions, then touch [OK].
Shutter button
F
MOVIE (Movie) button
Shooting still images
1Press the shutter button halfway down to focus.
When the image is in focus, a beep sounds and the • indicator lights.
2Press the shutter button fully down.
Shooting movies
1Press the MOVIE (Movie) button to start recording.
•Use the WFF (zoom) lever te change the zoom scale.
2 Press the MOVIE button again to stop recording.
611
18

• The sound of the lens and lever operating will be recorded when the zoom function
nperates while shooting a movie. The sound of tile MOVIE button operating may
alsn be recorded when movie recording is finished.
• Continuous shooting is possible lor approximately 29 minutes at one time at the
camera's default settings and when the temperature is approximately 25°C (77°F).
When movie recording is finished, you can restart recording by pressing tile
MOVIE button again. Recording may stop to protect the camera depending on tile
ambient temperature. GB
{5} (Playback)
1Press the _ (Playback) button.
• When images on a memory card recorded with other cameras arc played
back on this camera, the registration screen for the data file appears.
Selecting next/previous image
Touch _l (Next)/I"_ (Previous) on lhe screen.
• To play back movies, :ouch i_ (Playback) ill the center nlthe screen.
• To zoom in, lntlch lhe still image being played back.
Deleting an image
(_) Touch _ (Delete)-+ [Thishnage].
Returning to shooting images
Touch It_ on the screen.
• You can also return lo shooting mode by pressing the shutter button halfwaydown.
GB
19

This camera contains an internal function guide. This allows you to search the
camera's l'unctions according to your needs.
__ln'Camera Guide
1
2
Touch ?(In-Camera Guide).
• The ? mark will appear on the bottom right or'the screen while viewing.
Select a search method from tin-Camera Guide].
Shoot/playback guide: Search for various operation functions in
shooting/viewing mode.
Icon guide: Search the function and meaning of displayed icons.
Troubleshooting: Search common problems and their solution.
Objective guide: Search functions according to your needs.
Keyword: Search functions by key words.
History: Display the last 10 items displayed in tin-Camera Guide].
6B
2O