Sony DSC-M2 User manual

SERVICE MANUAL
DIGITAL STILL CAMERA
LEVEL 2
• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-897-51).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-897-41).
• Reference number search on printed wiring boards is available.
• Precaution on Replacing the SY-133 board
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision History
Revision History
Ver 1.0 2005. 10
On the PM-046 and SY-133 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the PM-046 and SY-133 board.
Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the PM-046
and SY-133 board are not shown.
The following pages are not shown.
Mounted parts location ....................... Pages 4-69 to 4-70
Electrical parts list.............................. Pages 5-11 to 5-17
How to use
Acrobat Reader
How to use
Acrobat Reader
Schematic diagram .............................Pages 4-23 to 4-48
Printed wiring board............................Pages 4-59 to 4-64
Waveforms ........................................... Pages 4-65
Sony EMCS Co.
2005J1600-1
©2005.10
Published by DITechnical Support Department
9-876-897-31
DSC-M2
DSC-M2
DSC-M2
US Model
Canadian Model
AEP Model
UK Model
E Model
Korea Model
Chinese Model
Hong Kong Model
Tourist Model
Japanese Model
Internal memory
ON BOARD
Internal memory
ON BOARD

—2 —
DSC-M2
SPECIFICATIONS
Camera
[System]
Image device 7.17 mm (1/2.5 type) color
CCD, Primary color filter
Total pixel number of camera
Approx. 5 255 000 pixels
Effective pixel number of camera
Approx. 5 090 000 pixels
Lens Carl Zeiss Vario-Tessar
3x zoom lens
f = 6.33 – 19.0 mm (38 –
114 mm when converted to a
35 mm still camera)
F3.5 – 4.4
Exposure control Automatic exposure, Scene
Selection (9 modes)
White balance Automatic, Daylight, Cloudy,
Fluorescent, Incandescent,
Flash
File format (DCF compliant)
Still images: Exif Ver. 2.2
JPEG compliant, DPOF
compatible
Movies: MPEG-4 compliant
(Stereo)
Recording media “Memory Stick Duo”
Flash Recommended distance (ISO
set to Auto): approx. 0.1 m to
2.6 m (3 15/16 inches to 8 feet
6 3/8 inches) (W)/
approx. 0.5 m to 2.1 m
(1 feet 7 11/16 inches to 6 feet
10 11/16 inches) (T)
[Input and Output connectors]
Multi connector
USB communication
Hi-Speed USB (USB 2.0
compliant)
[LCD screen]
LCD panel 6.2 cm (2.5 type) TFT drive
Total number of dots
123 200 (560x220) dots
[Power, general]
Battery pack usedRechargeable battery pack
NP-FT1
Power requirements
3.6 V
Power consumption
(during shooting) 1.2 W
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions 51.2x123.1x32.4 mm
(2 1/8x4 7/8x1 5/16 inches)
(W/H/D, excluding protrusions)
Mass Approx. 210 g (7.4 oz)
(including NP-FT1 battery
pack, “Memory Stick Duo” and
wrist strap, etc.)
Microphone Electret condenser microphone
Speaker Dynamic speaker
Exif Print Compatible
PRINT Image Matching III
Compatible
PictBridge Compatible
Cyber-shot Station UC-MB
[Input and Output connectors]
A/V OUT (STEREO) jack (Stereo)
Minijack
Video: 1 Vp-p, 75Z,
unbalanced, sync negative
Audio: 327 mV (at a 47 kZ
load)
Output impedance 1 kZ
USB jack mini-B
USB connection High-Speed USB
(USB 2.0 High-Speed
compatible)
DC IN jack
Camera connector
AC Adaptor AC-LS5
Input rating 100 V to 240 V AC,
50/60 Hz, 11 W
Output rating 4.2 V DC*
* See the label on the AC
Adaptor for other
specifications.
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions Approx. 48x29x81 mm
(1 15/16x1 3/16x3 1/4 inches)
(W/H/D, excluding projecting
parts)
Mass Approx. 130 g (5.0 oz)
excluding power cord (mains
lead)
Rechargeable battery pack NP-FT1
Used battery Lithium-ion battery
Maximum voltageDC 4.2 V
Nominal voltage DC 3.6 V
Capacity 2.4 Wh (680 mAh)
Design and specifications are subject to change
without notice.

—3 —
DSC-M2
1. Check the area of yourrepair for unsoldered or poorly-soldered
connections. Checkthe entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which,through functioning, showobvioussigns
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270˚C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENTWARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Dangerofexplosionif battery is incorrectlyreplaced.
Replace only with the same or equivalent type.

—4 —
DSC-M2
TABLE OF CONTENTS
1. SERVICE NOTE ........................................................1-1
2. DISASSEMBLY
2-1. DISASSEMBLY······························································2-1
2-2. CIRCUIT BOARDS LOCATION ···································2-5
2-3. FLEXIBLE BOARDS LOCATION ································2-6
HELP (List of caution points is shown here.)
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2) ···························3-1
3-2. OVERALL BLOCK DIAGRAM (2/2) ···························3-3
3-3. POWER BLOCK DIAGRAM (1/2) ································3-5
3-4. POWER BLOCK DIAGRAM (2/2) ································3-7
4. PRINTEDWIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM································4-1
4-2. SCHEMATIC DIAGRAMS
•MS-289 (1/3) (MS I/O, CONNECTOR)
SCHEMATIC DIAGRAM ······························4-5
•MS-289 (2/3) (FUNCTION KEY)
SCHEMATIC DIAGRAM ······························4-7
•MS-289 (3/3) (CONNECTOR)
SCHEMATIC DIAGRAM ······························4-9
•CONTROL SWITCH BLOCK (FK80100)
SCHEMATIC DIAGRAM ····························4-11
•CONTROL SWITCH BLOCK (PB80100)
SCHEMATIC DIAGRAM ····························4-12
•CONTROL SWITCH BLOCK (TW80100)
SCHEMATIC DIAGRAM ····························4-12
•FLASH UNIT (FLASH)
SCHEMATIC DIAGRAM ····························4-13
•MOTOR UNIT (PI (SENSOR) BOARD)
SCHEMATIC DIAGRAM ····························4-15
•FP-307 FLEXIBLE BOARD (DC JACK)
SCHEMATIC DIAGRAM ····························4-15
•FP-305 FLEXIBLE BOARD (SY-LD RELY, SP)
SCHEMATIC DIAGRAM ····························4-16
•FP-299 FLEXIBLE BOARD (CCD IMAGER)
SCHEMATIC DIAGRAM ····························4-17
•FP-300 FLEXIBLE BOARD (BATTERY TERMINAL)
SCHEMATIC DIAGRAM ····························4-19
•FP-301 FLEXIBLE BOARD (MULTI CONNECTOR)
SCHEMATIC DIAGRAM ····························4-20
•FP-302 FLEXIBLE BOARD (MS (CN004/CN006)-
SY(CN751/CN752 RELAY)
SCHEMATIC DIAGRAM ····························4-21
•FP-306 FLEXIBLE BOARD (HALL IC)
SCHEMATIC DIAGRAM ····························4-21
•FP-304 FLEXIBLE BOARD (POWER SW)
SCHEMATIC DIAGRAM ····························4-22
Shematic diagram of the PM-046 and SY-133 board
are not shown.
Pages from 4-23 to 4-48 are not shown.
4-3. PRINTED WIRING BOARDS
•MS-289(MS I/O, CONNECTOR, FUNCTION KEY,
CONNECTOR)
PRINTED WIRING BOARD ·······················4-51
•FP-299 FLEXIBLE (CCD IMAGER)
PRINTED WIRING BOARD ·······················4-55
•FP-301 FLEXIBLE (MULTI CONNECTOR)
PRINTED WIRING BOARD ·······················4-55
•FP-300 FLEXIBLE (BATTERY TERMINAL)
PRINTED WIRING BOARD ·······················4-56
•FP-302 FLEXIBLE (MS(CN004/CN006)-SY(CN751/
CN752) RELAY)
PRINTED WIRING BOARD ·······················4-56
•FP-304 FLEXIBLE (POWER SW)
PRINTED WIRING BOARD ·······················4-57
•FP-306 FLEXIBLE (HALL IC)
RINTED WIRING BOARD ·························4-57
•FP-305 FLEXIBLE (SY-LD RELAY, SP)
RINTED WIRING BOARD ·························4-58
•FP-307 FLEXIBLE (DC JACK)
RINTED WIRING BOARD ·························4-58
Printed wiring board of the PM-046 and SY-133 board
are not shown.
Pages from 4-59 to 4-64 are not shown.
4-4. WAVEFORMS
Waveforms of the PM-046 and SY-133 board is not
shown.
Page 4-65 is not shown.
4-5. MOUNTED PARTS LOCATION ·································4-67
Mounted parts location of the PM-046 and SY-133
board is not shown.
Pages from 4-69 to 4-70 are not shown.
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS ······················································5-3
5-1-1.OVERALL SECTION·····················································5-3
5-1-2.BT HOLDER SECTION·················································5-4
5-1-3.LCD SECTION ·······························································5-5
5-1-4.HINGE SECTION···························································5-6
5-1-5.LENS SECTION ·····························································5-7
5-2. ELECTRICAL PARTS LIST ··········································5-9
Electrical parts list of the PM-046 and SY-133 board
are not shown.
Pages from 5-11 to 5-17 are not shown.

1-1
DSC-M2
1. SERVICE NOTE
• NOTE FOR REPAIR
[Discharging of the FLASH unit’s charging capacitor]
The charging capacitor of the FLASH unit is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-M2 is simplyturned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 kΩ/1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Discharging the Capacitor
Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
Flash unit
Caution
Shorting jig
(1k
Ω / 1W) Capacitor

1-2
DSC-M2
Self-diagnosis display
• C: ss: ss
Thecontents which can be handled
by customer, are displayed.
• E: ss: ss
Thecontents which can be handled
by engineer, are displayed.
[Description on Self-diagnosis Display]
C:13:ss
Format the “Memory Stick Duo”.
Execute [Format Album] (page 1-3).
Insert a new “Memory Stick Duo”.
Unformatted “Memory Stick Duo”is inserted.
A format error on Album has occured.
“Memory Stick Duo”is broken.
FORMAT ERROR
MEMORY STICK ERROR
Display Code
C:32:ss
Countermeasure
Turn the power off and on again.
Cause
Trouble with hardware.
Caution Display During Error
SYSTEM ERROR
C:91:ss
E:61:ss
E:91:ss
Execute [Format Music] (page 1-3).
When you execute [Format Music] all
your stored Music files will be erased.
Tranfer the Music files using the
supplied application again.
Checking of lens drive circuit.
Checking of flash unit or replacement
of flash unit.
When transfering Music files from your
computer an error occured due to USB
disconnection or other problem.
When failed in the focus and zoom
initialization.
Abnormality when flash is being
charged.
—
—

1-3
DSC-M2
Method for Copying or Erasing the Data in Internal Memory (Album or Music)
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the
internal memory (album or music).)
Method for copying the data in Album
Method for formatting the Album
Note 1: When replacing the SY-133 board, erase the data in internal memory (album or music) of the board before
replacement.
Note 2: When replacing the SY-133 board or the IC901 on the SY-133 board, execute formatting and initialize the
internal memory (album and music) after replacement.
Copies all images in Album to a “Memory Stick Duo”. When using the battery pack, this
menu is not displayed. When you want to copy images, use the AC Adaptor (supplied).
1Insert a “Memory Stick Duo”having 64 MB or larger capacity.
2Select [OK] with von the control button, then press z.
The message “All data in album will be copied Ready?”appears.
3Select [OK] with v, then press z.
Copying starts.
•You cannot copy individual images.
•You cannot select a folder copied on a “Memory Stick Duo”.
•You can copy the images saved on Album to the “Memory Stick Duo”without deleting the images saved
on Album.
•After shooting images, you cannot copy the images in the recording folder/playback folder to Album.
•When playing back images in Album, the order of images displayed on the screen may be different from
that of images copied on the “Memory Stick Duo”.
Copy
OK
See the following procedure.
Cancel
Cancels the copying.
102
Copying
Formats Album.
•Note that formatting irrevocably erases all data in Album, including even protected images.
1Select [OK] with von the control button, then press z.
The message “All data in album will be erased Ready?”appears.
2Select [OK] with v, then press z.
The format is complete.
Format
OK
See the following procedure.
Cancel
Cancels the formatting.
Method for formatting the Music
If you cannot playback Music with Slide Show, the Music file may be damaged. In this case,
format the write-in-area for Music files first. Remove the “Memory Stick Duo,”then connect
the camera to your computer through the USB connection. Then transfer the desired music
using the supplied application, “Music Transfer”again.
•Once you format the write-in-area of Music files, all data in the area will be erased, and you cannot get it
back.
1Select [OK] with von the control button, then press z.
The message “All data will be erased Ready?”appears.
2Select [OK] with v, then press z.
The format is complete.
Format Music
OK
See the following procedure.
Cancel
Cancels the formatting.

1-4E
DSC-M2
Precaution on Replacing the SY-133 board
VIDEO OUT Default Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setteing
because of broadcast system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code
is right. If not, rewrite to the right value.
VIDEO OUT Default Data
Page Address Data
NTSC PAL
4F A1 00 01
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: A1, and set data: 00 (NTSC) or data: 01 (PAL).
3) Click
[Save] on the SEUS screen.
4) Select page: 80, address: 34, and check that the data is “00”.
5) Select page: 80, address: 30, and check that the data is “00”.
6) Select page: 00, address: 01, and set data: 00.
Initial Language Data Check
If the SY-133 board was replaced, initial language setting may be changed. Accordingly, change the following data so
as to set same initial language as that of the set distributing in each region.
Initial language: Language displayed at the next starting if the setting of Setup menu was reset.
It is different from the language setting selectable with the menu.
Initial Language Data
Page Address Data Language GP1 GP2 GP3 GP4 GP5
4F 88
00 English zzz z
01 Japanese z
04 Spanish z
08 Simplified Chinese z
0A Korean z
Note: GP1 is fixed to Japanese.
GP2 is fixed English.
GP3 is either English, or Spanish.
GP4 is fixed English.
GP5 is either English,Simplified Chinese, or Korean.
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 88, and set the Initial Language Data.
3) Click
[Save] on the SEUS screen.
4) Select page: 80, address: 34, and check that the data is “00”.
5) Select page: 80, address: 30, and check that the data is “00”.
6) Select page: 00, address: 01, and set data: 00.
7) Press the RESET button, then turn on the camera.
8) Check the language displayed when the camera starts.

DSC-M2 2-1 2-2
2-1. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2. DISASSEMBLY
SY-133
SY-133
SY-133
SY-133
PM-046
1
2
1
3
3
2
3
5
1
4
4
1
Four screws (M1.7x3)
2 Screw (M1.7x4)
3 Raise the multi connector side of the cabinet (front) assembly
in the direction of the arrow, and remove the claw.
4 Cabinet (front) assembly
1 Remove the speaker from the two claws.
2 Peel off the CD electric heat sheet.
3 FP-305 flexible board
4 Flexible board (from the FP-299 flexible board)
5 Lens section
Note: Be very careful not to
damage the flexible board.
Caution
Shorting jig
(1k
Ω / 1W) Capacitor
1 Discharging the capacitor
1
2
1
Connector
2 Flash unit (FL80100)
1 Four screws (M1.7x3)
2 P cabinet (C) assembly
3 Harness (PD-135)
4 Harness (MA-155)
5 P cabinet (M) assembly
1
3
4
5
2
1
1
Two screws (M1.7x3)
2 Microphone holder
3 Two Microphones (MIC901, MIC902)
4 Control switch block (PB80100)
5 Screw (M1.7x3)
6 LCD unit, PM-046 board
7 P cabinet (M) assembly
2
1
4
6
5
7
3
HELP 01
A
(See page 2-3)

DSC-M2
2. DISASSEMBLY
2. DISASSEMBLY
2-3 2-4
SY-133
MS-289
SY-133
3
7
5
6
8
9
4
2
1
1
Multi cushion
2 Two tapping screws (M1.7x3)
3 Multi retainer sheet metal
4 Two dowels
5 FP-301 flexible board
1 Open the jack cover.
2 Screw (M1.7x3)
3 DC holder assembly
4 Screw (M1.7x2)
5 FP-307 flexible board
6 FP-300 flexible board
7 Two screws (M1.7x3)
8 FP-307 flexible board
9 SY-133 board.
1 Screw (M2x3)
2 ST sheet metal
3 Two screws (M2x3)
4 Cabinet (rear) assembly
5 LCD hinge section
3
4
5
2
1
Four screws (M1.7x3)
2 P cabinet (C) assembly
3 Harness (PD-135)
4 Harness (MA-155)
5 P cabinet (M) assembly
6 Hinge section
1 Four screws (M1.7x3)
2 Hinge cover assembly
3 FP-306 flexible board
4 Two shuttle screw protection sheets
5 Two screws (M1.7x3)
6 Claw
7 Control switch block (FK80100)
8 Harness (FK-061)
1 Harness (MA-155)
2 Harness (PD-135)
3 Harness holder
4 Two screws (M1.7x3)
5 Hinge cabinet
6 LCD hinge
1
1
2
1
5
4
7
6
8
3
1
6
3
2
5
4
3
4
6
5
2
1
1
3
4
5
2
1
4
6
1
2
3
5
1
FP-302 flexible board
2 FP-302 flexible board
3 FP-304 flexible board
4 Screw (M1.7x3)
5 MS-289 board
6 Insulating sheet (MS)
A
(See page 2-2)
HELP 03
3
4
9
8
7
6
5
1
Screw (M1.7x3)
2 SP holder
3 Three tapping screws (M1.7x3)
4 Screw (M1.7x4)
5 Open the BT cover.
6 Harness (PD-135)
7 Harness (MA-155)
8 Harness (FK-061)
9 BT holder section
HELP 02
1
2
FP-306 flexible board

2-5
2. DISASSEMBLY
2. DISASSEMBLY
DSC-M2
2-2. CIRCUIT BOARDS LOCATION
PM-046
SY-133
FP-299
FP-301
FP-300
FP-306
FP-305
NAME FUNCTION
FP-300
FP-301
FP-304
FP-305
FP-306
FP-307
MS-289
PM-046
SY-133
BATTERY TERMINAL
FP-299 CCD IMAGER
MULTI CONNECTOR
FP-302 MS(CN004) - SY(CN751) RELAY / MS(CN006) - SY(CN752) RELAY
POWER SW
SY-LD RELAY, SP
HALL IC
DC JACK
MS I/O, CONNECTOR, FUNCTION KEY, CONNECTOR
LCD PANEL DRIVE, MIC AMP
CAMERA A/D CONV.TIMING GENERATOR, LENS DRIVE, CAMERA DSP, LENS CONTROL,
CAMERA SYSTEM CONTROL, DIGITAL SIGNAL PROCESS, SUPER AND FLASH MEMORY,
SDRAM, HI CONTROL, AUDIO AMP, SPEAKER AMP, CONNECTOR, DC/DC CONVERTER
FP-307
FP-304
MS-289

2-6E
2. DISASSEMBLY
2. DISASSEMBLY
DSC-M2
2-3. FLEXIBLE BOARDS LOCATION
The flexible boards contained in the lens block and flash unit(FL80100) are not shown.
CONTROL SWITCH BLOCK
(FK80100)
FP-302 CONTROL SWITCH BLOCK
(PB80100)
CONTROL SWITCH BLOCK
(TW80100)
NAME FUNCTION
FP-300
FP-301
FP-304
FP-305
FP-306
FP-307
MS-289
PM-046
SY-133
BATTERY TERMINAL
FP-299 CCD IMAGER
MULTI CONNECTOR
FP-302 MS(CN004) - SY(CN751) RELAY / MS(CN006) - SY(CN752) RELAY
POWER SW
SY-LD RELAY, SP
HALL IC
DC JACK
MS I/O, CONNECTOR, FUNCTION KEY, CONNECTOR
LCD PANEL DRIVE, MIC AMP
CAMERA A/D CONV.TIMING GENERATOR, LENS DRIVE, CAMERA DSP, LENS CONTROL,
CAMERA SYSTEM CONTROL, DIGITAL SIGNAL PROCESS, SUPER AND FLASH MEMORY,
SDRAM, HI CONTROL, AUDIO AMP, SPEAKER AMP, CONNECTOR, DC/DC CONVERTER

DSC-M2
HELP
HELP
Disassembling and assembling procedures that require attention are described here.
PM-046
Microphone holder Microphone holder
HELP 01
When installing the BT holder section, install it while
aligning the two switches of the MS-289 board with
the two switches of the rear cabinet assembly .
MS-289 board
Switch
Switch
Rear cabinet
assembly
BT holder section
HELP 02
When installing the microphones, be sure to embed
them horizontally in the dents.
Microphon(MIC901)
Microphon(MIC902) Microphon(MIC901)
Microphon(MIC902)
Two screws (M1.7x3)

DSC-M2
HELP
Installation procedure
Attach the
adhesive surface
Control switch block
(TW80100)
Control switch block
(TW80100)
Positioning holes
MS-289 board
HELP 03
Positioning holes
1. Insert the control switch block (TW80100) into the connector of the
MS-289 board. (Lock the connector.)
2. Remove the release paper from the back of the control switch block (TW80100).
3. Fold the control switch block (TW80100) and align the positioning holes
of the control switch block (TW80100) with the positioning holes of the MS-289 board.
4. Adhere the control switch block (TW80100) to the MS-289 board in that state.

DSC-M2
Link
Link
3. BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM (1/2)
POWER BLOCK DIAGRAM (2/2)
OVERALL BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM (1/2)
POWER BLOCK DIAGRAM (2/2)

DSC-M2 3-1 3-2
3-1. OVERALL BLOCK DIAGRAM (1/2)
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
TIMING
GENERATOR
CAMERA DSP,
LENS CONTROL
IRIS A
IRIS XA
IRIS B
IRIS XB
ZOOM A
ZOOM XA
ZOOM B
ZOOM XB
FOCUS A
FOCUS XA
FOCUS B
FOCUS XB
HR EN3
HR DIR3A
HR DIR3B
HR EN0
HR DIR0A
HR DIR0B
HR EN2
HR DIR2A
HR DIR2B
LENSV OUTA
LENSV OUTB
XZM RST SENS1
LENSV LED+
LENSV LED-
LENSV OPENSENS
XFC RST SENS
M_5V
IRIS MOTOR
DRIVE
FOCUS MOTOR
DRIVE
ZOOM MOTOR
DRIVE
LENS BARRIER
MOTOR DRIVE
IC151
F4
F3
E4
G1
F2
E2
D2
B1
B4
B5
B3
A3
G6
E3
F5
D3
C4
A1
A2
C3
B6
C5
D5
A6
D6
E6
B7
C6
M
IRIS
MOTOR
LENS
BARRIER
MOTOR
ZOOM
MOTOR
FOCUS
MOTOR
ZOOM RESET
SENSOR
LENS BARRIER
OPEN SENSOR
FOCUS RESET
SENSOR
CCD IMAGER
FP-299 (FLEXIBLE BOARD)
CCD BLOCK ASS'Y
FP-301
(FLEXIBLE
BOARD)
(1/2)
FLASH UNIT (FL80100)
SY-133 BOARD (1/2)
FP-305
(FLXIBLE
BOARD)
LENS UNIT
PI (SENSOR)
BOARD
IC002
IC001
S/H
(1/11)
(3/11)
(3/11)
(6/11)
(3/11)
(8/11)
(5/11)
(6/11)
(4/11)
IC101
IC301
CAMERA
SYSTEM
CONTROL
IC501
AUDIO
AMP
IC801
CODEC
IC201
SDRAM
PLL
IC202
LENS UNIT
IRIS
SHUTTER
27, 26
19-17 H1A,H1B
H2A,H2B
RG
V1A,V1B
V2
V3A,V3B
V4
V5A,V5B
V6
V7A,V7B
V8
IC303
VIDEO
AMP
IC302
2
5
3
6
13
20
|
28
30
|
32
14
11
26
27
3
1
4
2
6
8
5
7
19
18
21
20
CN002 CN708
CN702
CN703
Q801,802
2
4
11
3
15
|
12
CN001
PH001
1
2
6
5
11
|
8
14
11
25
3
1
4
2
6
8
5
7
19
18
21
20
15
CN701
CCD OUT
CA FD
CLK TGO
BUFFER
Q302-304
BUFFER
Q501
MOD
MUTE
AU MIX SW AU MIX SW
77
80
CA HD, CA FD
CA FD
XZM RST SENS1
XFC RST SENS
1-5,7,8,9
11-14
28
29
23
22
97, 98
100, 101
103-105
2 - 4
7, 10
14, 18
N21
L21
P21
STRB ON
LENSV OPENSENS
LENSV RST LED
LENSV ENB
LENSV DIR
K20
L22
J21
M21
M20
N20
RO
GO
BO
PANEL R
PANEL G
PANEL B
PANEL R
PANEL G
PANEL B
STRB CHG CONT
HD0
PANEL V
HD0
PANEL V
F20
F21
W21
Y22
Y13, AB13
Y14, AA13
AB14, Y15
AB15, AA14
AA15, Y16
AB16, AA16
AB17, AA17
U4, V3, V2, W1
V4, W2, W4, Y4
Y2, AA1, W3, AA2
Y3, AA3, AC1, AB2
Y17
AB18
AC16
AC20
T20
AB4
Y20
T22
MC CKIO
MC CKIO
MC A20,MC A21
XSYS RST
HD
VD
FLD ADA SIA
ADA SOA
ADA SIA
ADA SOA
XACCESS LED
PB MODE LED
REC MODE LED
AUDIO L OUT
AUDIO R OUT
V OUT
MIC L
MIC R
MIC L
MIC R
T23
AA23
FCK27
B22
AA11
B16
C15
A15
D15
B15
D16
MC MSDIO,D1-D3
MC MSBS
MC MSCLK
TO
OVERALL
BLOCK DIAGRAM
(2/2)
TO
OVERALL
BLOCK DIAGRAM
(2/2)
(PAGE 3-3)
(PAGE 3-3)
F21
ADA ADCK
ADA ADCK
DAOUT L
DAOUT R
EVRIN L
EVRIN R
ADA ADCK
AOUT
AOUT
MIX OUT
BEEP
AC12
V OUT
YO
XSYS RST
F23
11, 8
16
12, 9
91
5, 6
88
102, 90
79
MC D0 - MC D15
DQ0 - DQ31
CLK
SDR CLK
A0 - A11,
BA1,BA0
SDR D0 - SDR D31 SDR A0 - SDR A11,
SDR A13, SDR A14
J3, L2, L4, L1, K3
L3, M2, M4, M3, N2
N3, P2, N4, P4, P3
R1, R3, R2, T3, T1
R4, T2, T4, U2, U3
BEEP
AU MIX BGM AU MIX MAIN
XAE LOCK ON
XSHTR ON
XSYS RST
10
12
16
18
20
C22
PRELAMP AF CONT
F1
XLCD OPEN SW EN
L22
SELFTIMER LED
H23
KEY AD SHTL
B1
MC A1 - MC A23
HIGH
VOLTAGE
CHARGER
IGBT
DRIVE
STRB CHRG
ST UNREG
STRB CHG CONT
XSTRB FULL
STRB ON
FLASH
DRIVE
D001
(RECT)
T001
Q001
C901
SP901
SP+
SP-
XENON
TUBE
MAIN
CAPACITOR
SPEAKER
B20
STRB CHRG
XSTRB FULL
CN001
MULTI
CONNECTOR
(CRADLE)
AB7
AD14
MELODY
E21
AB18
ADA ADCK ENA
MELODY ENV
2
1
XE A(H)
XE K(L)
6015 31
37
44
40
48
53
89,93
56
CA AD0 - CA AD13
M
M
M
7
15
4
10
6
9
MC D0 - MC D15 MC D0 - MC D15
MC A1 - MC A25 MC A1 - MC A25
2
4
B21, D19
C20, B20
A20, D18
C19, B19
YC0 - YC7
B9, C9
A9, D9
D10, B10
A10, C10
D22
C22
D20
F18
G19
E21
E23
C23
D23
C18
D17
63
1
P1, N3, N2, N1
M2, M1, M3, L4
L2, L1, L3, K4
K3, K1, K2, J4
W2, W3, V4, U4, V2
V3, U3, U2, W1, V1
T2, T3, U1, V5, R3
R2, T1, P4, P3, R1
M4, P2, N4
Y19, Y20, V18, Y18
W17, W18, AA19, AA18
W16, V17, Y17, Y16
V16, W15, AA17, Y15
V15, V14, AA16, W14
Y14, AA15, AA14, Y13
W13, V13, AA13, V12
Y12, W12, AA12, V11
V9, Y8, W8, AA8
V8, Y7, W7, AA7
Y6, V7, AA6, W6
AA5, W5
3, 5, 6, 8, 9,11,12,14
77,79,80,82,83,85,86
88,32,34,35,37,38,40
41,43,48,50,51,53,54
56, 57, 59
26-28,63-69
25,22,24,23 71
AD19
A7
A6
AC15
G1
A23
D23
AC12
Y4
Y3
Y2
27
12
79
26
31
L21, L23, M24,K23
H22, J21, J22, F24
K21, H21, M23, K22
G21, L24, F23, E23
V22, V21, V23, R22
W22, U22, W21, T22
R23, N21, P22, P21
P23, R21, M22, T21
P24, U21, U23, N22
U24, N23, T24, M21
T23
+
SYS SO, SI, SCK
B11
A11
C11
D13
B13
C13
AU SO, XAU SCK
AB5
AB13
AB22
AB11
D14
K2
A12
B12
38,35
71
77
2
4
49
47
50
48
FR SO, SI, SCK
L1, M1
J1, K1 USBPHY D+, D- D+, D-
16
14
10
8
6
VIDEO/AUDIO SIGNAL
VIDEO SIGNAL
AUDIO SIGNAL
SPEAKER
AMP
IC853
3
7
10
1
2
Q804
Q805
BUFF
MUTE
Q806,807
BUFF
L
R
L
R
ALC
AMP
IC851
35
2
5
3, 7
1
6
2
5
3, 7
1
6
IC803 IC802
A10
B10
K3, J3
F4
H7, H9, G6, G9, F7, E8, D10, D9, H8
H10, G8, G10, E7, E9, D7, E10
IC901 SUPER AND FLASH MEMORY
27MHz
XTAL OSC
X501
AU MIX BGM
AU MIX MAIN
(2/11)
(9/11)
IC001
(9/11)
(8/11) (8/11)
SW
Q153
CAM SO, XCAM SCK
CAM SO, XCAM SCK CAM SO, XCAM SCK
MC D0 - MC D15
MC A1 - MC A23

DSC-M2 3-3 3-4
3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN001
MULTI
CONNECTOR
(CRADLE)
J001
(11/11)
(11/11)
(7/11)
(2/2)
(2/3)
(1/2)
(PAGE 3-2)
(PAGE 3-2)
SYS SO, SI, SCK
BATTERY
TERMINAL
FP-301
(FLEXIBLE
BOARD)
(2/2)
SY-133 BOARD (2/2)
FP-300
(FLEXIBLE
BOARD)
FP-307
(FLEXIBLE
BOARD)
26
6
24
19
21
23
25
27
|
33
1
|
6
9
|
14
15
CN703
CN705BT001
BATT UNREG
5
|
1
CN706
REG GND
BATT SIG
AV JACK IN
BATT/XEXT M
BATT/XEXT D
REG GND
XMULTI IN
USB VBUS
AV JACK IN
BATT/XEXT
XMULTI IN
XUSB JACK IN
ACV UNREG
ACV UNREG
1
24
18
3
4
1
6
S
IC001
IC004
DC/DC
CONVERTER
DC/DC
CONVERTER
IC491
HI CONTROL
RESET
3V
REG
VL 3V
D011
D036
D013
Q006,009
D015
F004
F003
XRSTX
DDCON SO
DDCON SCK
BACK UP VCC
ST UNREG
ACV UNREG FR
BATT UNREG
EVER 3.0V
BATT IN
INIT CHARGE
FAST CHARGE
SYS DD ON
D 1.2V
D 2.8V
AU 3.1V
M 5V
ST 5V
CAM 3.1V
CAM 15.0V
CAM -8.0V
PANEL 8.5V
BL LEV
LED A
LED K
D 1.5V
Q412
OUT8A
OUT8B BATTERY IN
DETECT
BATTERY
CHARGER
FET DRIVE
D2
D1
E1
F002
D403
D404
FR SO
FR SI
FR SCK
32KHz IN
32KHz OUT
MEMORY
STICK
DUO
CN006
CN752
CN751(1/2)
CN101
MIC901
MIC902
CN201
LED901
CN202
D103 (ACCESS)
4,3,5,7,
2,8
6
PM-046 BOARD
CONTROL SWITCH
BLOCK (PB80100)
Q102
LCD901
LED
DRIVE
S206
PHOTO
S002
ZOOM T
S001
ZOOM W
S202
HYBRID
Q407
Q753
Q404
Q406
Q402
I/F
SW
S001-003
DISPLAY,
MOVIE,
PHOTO
RGB
DRIVE
COLOR
LCD UNIT
IC201
MIC AMP
IC301
TIMING
GENERATOR
BACK LIGHT
CONTROL SWITCH
BLOCK (TW80100)
CONTROL SWITCH BLOCK (FK80100)
MS-289 BOARD
CN302
CN203
CN002
CN004(2/2)
CN751
(2/2)
CN003
CN301
3
1
1
3
2
4
1
6
22
19
14
11
9
7
2
24
23
34
33
32
11
26
8
10
2
13
25
23
6
5
4
21
22
B8
A1
COM, CS
PSIG
BL H
BL L
VST,VCK,EN,DWN
XSTBY,PCG,HST,REF
WIDE,HCK2,HCK1,RGT
R
G
B4
5
3
S002
POWER
R001 CN001
SHUTTLE KEY
S001-005
RIGHT,SET,DOWN,LEFT,UP
S006-008
INDEX,DUST,MENU
D002 (REC)
D009 (AF LED)
XAE LOCK ON
XAE LOCK ON
XSHTR ON
XSHTR ON
XCHARGE/XSTRB LED
KEY AD3
KEY AD1
KEY AD4
ZOOM T
ZOOM W
XPOWER ON
KEY AD0
D003 (PB)
D001 (FLASH/CHARGE)
LCD_TURN_SW
MIC
L
MIC
R
15
13
8
3
31
2
7
9
2
3
CN002
7
9
2
3
13
12
11
6
1
4
2
3
18
15
17
5
7
8
9
14
20
16
18
17
2
5
3
15
CN003
7
8
9
14
20
16
18
17
2
5
3
15
Q751
LED
DRIVE
PANEL R
PANEL G
PANEL B
PANEL R
PANEL G
PANEL B
PANEL V
HD0
XACCESS LED
MS IN
BATT SI
BATT SIG
ACV W SENS
BATT SO
XMS IN
PB MODE LED
AF LED K
KEY AD SHTL
AF LED K
XZOOM_W
XZOOM_T
XCHARGE/XSTRB_LED
KEY AD1
KEY AD0
XPWR ON
KEY AD SHTL
PB MODE LED REC MODE LED
REC MODE LED
MIC L
MIC R
MC MSDIO,D1-D3
MC MSBS
MC MSCLK
XSYS RST
XSYS RST
KEY AD SHTL
PRELAMP AF CONT
SELF TIMER LED
XLCD OPEN SW EN
XLCD OPEN SW
XLENZ CAP OPN
LED A
LED K
KEY AD2
XRESET SW
VL 3V
BL LEV
TO
OVERALL
BLOCK DIAGRAM
(1/2)
TO
OVERALL
BLOCK DIAGRAM
(1/2)
2
1
X402
32.768KHz
A3
C8
C4
A7
G2
G1
FR SO, FR SI, XFR SCK
D8
E4
D9
E9
E5
D4
A10
B11
D1
B7
A7
E3
3
D2 J1
B9
A11
L8
K8
C7
D7
DDCON SO, DDCON SCK
A9
H2
E8
D7
C1
D3
A5
H4
B7
KEY AD2 G6
B3
B6
B1
MODE DIALO XHIBLID REC
J8
J7
H7
H6
J6
B8
J4
J5
LED
DRIVE
CN004(1/2)
21
6
24
22
30
19
7
9
26
27
28
11
10
24
29
19
20
21
26
31
30
28
29
14
17
15
27
7
8
6
4
9
2
11
5
45
42
44
48
1
3
31
20
21
22
28
17
16
14
12
5
26
24
G6
H2
VIDEO/AUDIO SIGNAL
VIDEO SIGNAL
AUDIO SIGNAL
IC402
LITHIUM
BATTERY
BT101
(SECONDARY)
DC IN
10
|
7
Q752
LED
DRIVE
FP-302
(FLEXIBLE
BOARD)(1/2)
FP-302
(FLEXIBLE
BOARD)
FP-302
(FLEXIBLE
BOARD)(2/2)
CN005
CN007
10
2
7
8
6
2
3
4
5
CN001 5
2
4
CN002
5
2
4
FP-304
(FLEXIBLE
BOARD)
5
6
17
19
1
30
25
24
26
28
23
30
27
21
S203,204
MOVIE
MODE
S205
5SEC
Q201
SW
RESET
S201
LCD OPEN
SENSOR
IC201
2
LCD TURN
SENSOR
IC001
2
FP-306 (FLEXIBLE BOARD)
(7/11)
PANEL V
XSYS RST
BL LEV
MIC L
MIC R
KEY AD2_2
KEY AD2_4
HD0
SYS SO
SYS SI
SYS SCK

DSC-M2 3-5 3-6
3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
IC001
DC/DC
CONVERTER
3V
REG
E4
F004
L002
L001
L006
F003
D 2.8V
D 1.5V
D 1.2V
D 1.2V
M 5V
AU 3.1V
PANEL 8.5V
ST 5V
CAM 15V
CAM -8.0V
SYS DD ON
BACK UP VCC
XRSTX
BATT IN
MODE DIALO
BATT/XEXT
BATT SI
BATT SO
ACV SENS
DDCON SO
DDCON SCK
XCS DDCON
SYS DD ON
FAST CHARGE
DD CON SENS
XRST SYS
XSYS RST
SYS DD ON
FAST CHARGE
INIT CHARGE
INIT CHARGE
EVER 3.0V
OUT8A
OUT8B
DIN
CLK
LD
BATTERY IN
DETECT
DC/DC
CONVERTER
BATTERY
CHARGER
FET
DRIVE
RESET
E3
D7
A9
H8
G8
E8
L8
K8
K7
C1
D3
H1
A5
H4
C7
D7
D9
E9
E5
D4
A11
B7
B9
J1
H2
F8
B3
A7
D011
D036
D013
D015
Q006,009
D017
(RECT)
D026
(RECT)
A10
D8
B11
D1
F9
F10
E11
D2
VCC2
OUT2
K6
OUT4
L5
OUT5
C8
VLDO4
VLDO5 B8
VCC7 J4
VOS72 K4
VOS73 L3
VCH7 K3
VCH2
L005
L007
L008
L009
L004
L011
Q003
SWITCHING
Q004
SWITCHING
VCC1A
VCC1B
VCC1C
G11
G10
G9
K5
VCC5
J6
VCH4
J5
VCH5
H2
VCH3S
H1
VCC GD
G2
ICH6 LED K
LED A
BL LEV
CAM 3.1V
B1
REF6
VCH1A
VCH1B
VCH1C(FB4)
L10
K9
L9
H11
H10
J11
OUT12A
OUT12B
OUT12C
OUT11A
OUT11B
OUT11C
L11
K10
J9
VCH3A(FB3)
VCH3B
VCH3C(FB6)
J1
H4
H3
OUT3A
OUT3B
OUT3C
J3
K1
J2
D023(RECT)
D021
(RECT)
L013
F1
OUT6
G1
VCH6
D025
(RECT)
G2
A7
X PWR ON
X PWR ON
EVER 3.0V
M 5V
XRESET SW
B8
XCHARGE/
XSTRB LED
XCHARGE/
XSTRB LED B1
G1
Q407
CN005
Q402
I/F
IC491
HI CONTROL
IC004
5
11
8
2
RESET
S201
R003
D001
(FLASH/CHARGE)
POWER
S002
F002
FP-301
(FLEXIBLE
BOARD)
SY-133 BOARD (1/2)
1
19
21
23
25
27
33
CN703
LITHIUM
BATTERY
(SECONDARY)
BT101 CN004 VL 3V
BATT/XEXT M
ACV UNRG ACV UNREG FR
9
14
FP-300
(FLEXIBLE
BOARD)
1
15
6
CN705
BATT UNREG
REG GND
BATT SIG
30
2
CN751
(1/2)
S
BATTERY
TERMINAL
BT001
15
PANEL 8.5V
BL LEV
LED A
LED K
ST UNREG
ST UNREG
ST 5V
TO
POWER
BLOCK DIAGRAM
(2/2)
1
4
3
6
1
3
7
28
2
30
26
31
29
25
4
D009
AF
LED
AF LED 5V
MS-289
BOARD
(1/2)
LCD
OPEN
SENSOR
IC201
FP-302
(FLEXIBLE
BOARD)
FP-304
(FLEXIBLE
BOARD)
CN001
MULTH
CONNECTOR
(CRADLE)
(7/11)
(11/11)
(7/11)
(11/11)
(PAGE 3-7)
J001
FP-307
(FLEXIBLE
BOARD)
5
|
1
CN706
BATT/XEXT D
REG GND
ACV UNREG
6
DC IN
10
|
72
14
5
D403 D404
ACV W SENS
IC402
Q005 D001
BUFF
(2/3)

DSC-M2 3-7 3-8E
3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
MEMORY
STICK
DUO
CN101
CN202
CN003
CN003
CN002 CN002
CN002
R001
CN006(1/2)
CN006(2/2)
CN001
CN001
CN752
(2/2)
CN752
(1/2)
CN751
(2/2) CN004
9
CN708
CN701
Q101
PM-046 BOARD
MS-289 BOARD(2/2)
FP-305
(FLEXIBLE BOARD)
RGB DRIVE,
TIMING
GENERATOR
PANEL 8.5V PANEL 8.5V
PANEL 8.5V
D 2.8V PANEL 2.8V
PANEL 5V
D 2.8V
D 2.8V
ST 5V
MIC 2.8V
MS 2.8V
D 2.8V
MS PWR ON
XE A(H)
ST UNREG
ST UNREG
STRB CHRG
XSTRB FULL
M 5V LENSV LED+
Q103,104
CAM 15.0V CAM 15.0V CD
CAM -7.5V CD
CAM -8.0V
CAM DD ON
ST 5V
ST 5V
L302
D 2.8V
VCC
IC201
MIC
AMP
IC301
AUDIO
AMP
IC801
CODEC
IC201
SPEAKER
AMP
IC853
ALC
AMP
IC851
SDRAM
IC202
3V
REG
IC102
CCD
IMAGER
IC002
BUFFER
IC001
TIMING
GENERATOR,
A/D
CONVERTER
IC101
IRIS/ZOOM/FOCUS
MOTOR DRIVE,
LENS BARRIER
MOTOR DRIVE
IC151
COLOR
LCD UNIT
LCD901
LED901
BACK LIGHT
CCD BLOCK ASS'Y
FP-299
(FLEXIBLE BOARD)
CN201
3
1
18
BL H
BL LEV BL LEV
BL LEV
AU 3.1V
M 5V
LED A
LED A
XZM RST LED
BL L
LED K
BL H
BL L
LED K
MS PWR ON
17
20
19
20
7
9
8
2
4
3
25
23
24
30
28
29
1
31
12
15
22
SHUTTLE KEY
CAM 3.1V
XSYS RST XSYS RST
XSYS RST
XSYS RST
XZM RST LED
XZM RST VCC
XFC RST LED
XFC RST VCC
Q152
T001
D001
(REG)
Q151
R156
D 2.8V
AU 3.1V
D 1.5V
D 2.8V ZOOM RESET
SENSOR
FOCUS RESET
SENSOR
FLASH UNIT (FL80100)
CONTROL SWITCH
BLOCK (FK80100)
LENS UNIT
LENS UNIT
PI (SENSOR)BOARD
HIGH
VOLTAGE
CHARGER
IGBT
DRIVE
PH001
XENON
TUBE
MAIN
CAPACITOR
C901
EVEN
CAMERA
DSP
IC301
VIDEO
AMP
PLL
IC302
D 2.8V
AU 3.1V
D 1.2V
IC303
CAMERA
SYSTEM
CONTROL
IC501
IC502
D 2.8V
D 1.8V
D 1.2V
AU 3.1V
SYS DD ON
CN002
CN001
12
10
17
15
LENS BARRIER
OPEN SENSOR
6
1.8V REG
XFC RST LED
T20
XSYS RST
STRB CHRG
XSTRB FULL
MS PWR ON
CAM 15V
CAM -8.0V
CAM DD ON
CAM 3.1V
SY-133 BOARD (2/2)
TO
POWER
BLOCK DIAGRAM
(1/2)
(PAGE 3-6)
1
15
12
13
12
13
11
12
18
16
17
5
20
13
12
20
18
16
17
5
11
3
31
V21
U22
D14
K2
AD19
AD18
AC20
AC15
3
1
4
CN702
15
|
12
4
11
1
SUPER AND
FLASH
MEMORY
IC901
AU MIX
SW
IC802
IC803
Q808,809
(1/11)
(3/11)
(3/11)
(3/11)
(6/11)
(6/11)
(8/11)
(8/11)
(4/11)
(4/11)
(5/11)
3
4
FP-302
(FLEXIBLE BOARD)(1/2)
FP-302
(FLEXIBLE BOARD)
FP-302
(FLEXIBLE BOARD)(2/2)
3 3
LCD
TURN
SENSOR
IC001
FP-306
(FLEXIBLE
BOARD)
IC001
9
3
15
10 1
2
EVEN
4
1
3
(9/11)(9/11)
(1/11)
(2/11)
(1/2)
(2/2)
F4

DSC-M2 4-1
4-1. FRAME SCHEMATIC DIAGRAM
4. PRINTEDWIRING BOARDS AND SCHEMATIC DIAGRAMS
4-2 FRAME SCHEMATIC DIAGRAM
24P
CN201
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
2P
CN301
1
2
2P
CN302
1
2
CN001
2
4
68
1012
14
16
1820
22
24
26
13
579
15
1719
21
23
25
33P
CN701
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
21PCN002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
10P
CN002
1
2
3
4
5
6
7
8
9
10
10PCN002
1 2 3 4 5 6 7 8 9
10
10PCN706
1
2
3
4
5
6
7
8
9
10
29P
CN708
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
6P
CN002
1
2
3
4
5
6
6PCN001
1
2
3
4
5
6
15PCN702
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15
15P
CN705
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
33P
CN703
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
31PCN751
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
31PCN752
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
31P
CN004
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
31PCN006
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
11PCN001
1
2
3
4
5
6
7
8
9
10
11
11PCN005
1
2
3
4
5
6
7
8
9
10
11
6P
CN007
1 REG_GND
2 XZOOM_T
3 XZOOM_T
4 XZOOM_W
5 XZOOM_W
6 REG_GND
CN101
10P
1
2 3
4
5
6
7
8
9
10
20PCN003
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20
6P
CN203
1
2
3
4
5
6
6PCN202
1 2 3 4 5 6
6P
CN001
1
2
3
4
5
6
20PCN003
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
A
BATT_UNREG
REG_GND
BATT_SIG
REG_GND
BATT_UNREG
BATT_UNREG
BATT_UNREG
REG_GND
REG_GND
PCG HCK2 G VSS EN R RGT XSTBY WIDE TEST2 VCK TEST1 COM VST DWN N.C. CS REF PSIG B VSSG VDD HST HCK1
MIC GND
MIC SIG
MIC_L
SPEAKER
MIC SIG
MIC GND
BATT/XEXT_D
REG_GND
ACV_UNREG
ACV_UNREG
ACV_UNREG
ACV_UNREG
REG_GND
RG
REG_GND
H1A
VST
V4
H1B
V1B
VHLD
V5B V5A
REG_GND
V7A
H2B
REG_GND
POWER_SAVE
CCD_OUT
V3B
REG_GND
V7B
V2
V1A
REG_GND
V6
H2A
REG_GND
V8
SHT
V3A
REG_GND
CSUB
CAM_-7.5V_CD
CAM_15V_CD
REG_GND
REG_GND
REG_GND
REG_GND
ZOOM_XB
FOCUS_A
LENSV_OPENSENS
IRIS_B
LENSV_OUTB
FC_RST_GND
REG_GND
FOCUS_XB
ZOOM_A
LENS_TEMP
IRIS_XB
LENSV_LED+
LENSV_LED-
FC_RST_VCC
SP-
SP+
FOCUS_XA
ZOOM_B
IRIS_A
TEMP_GND
FC_SENS
ZM_RST_VCC
FOCUS_B
IRIS_XA
ZOOM_XA
ZM_SENS_1ST
LENSV_OUTA
ZM_RST_GND
N.C.(GND)
AU_GND
AU_GND
KEY_AD2_2
MIC_L
REG_GND
KEY_AD2_4
MIC_R
AU_GND
REG_GND
MIC_2.8V
STATIC_GND
REG_GND
KEY_AD1
D_2.8V
KEY_AD_SHTL
KEY_AD0
REG_GND
AU_GND AU_GND
MIC_L
AU_GND
MIC_R
KEY_AD2_2 KEY_AD2_4
MIC_2.8V
REG_GND
FOCUS_XB
FC_SENS
ZM_SENS_1ST
ZOOM_XB
IRIS_XB
IRIS_XA
N.C.(GND)
FOCUS_B
IRIS_B
FOCUS_XA
ZOOM_B
FOCUS_A
ZOOM_XA
ZOOM_A
FC_RST_VCC
TEMP_GND
LENS_TEMP
IRIS_A
FC_RST_GND
ZM_RST_GND
ZM_RST_VCC
LCD_TURN_SW
D_2.8V
LCD_TURN_SW
D_2.8V
GND
GND
CONTROL SWITCH BLOCK
(FK80100)
ST_UNREG
STRB_CHRG
ST_GND ST_GND
ST_5V
ST_UNREG
ST_GND
ST_UNREG
XSTRB_FULL
ST_GND
STRB_CHG_CONT
ST_UNREG
STRB_ON
ST_GND ST_GND
REG_GND
REG_GND
BATT_UNREG
BATT_UNREG
N.C. ACV_GND ACV_UNREG ACV_GND ACV_UNREG V_GND BATT_XEXT_M D- ACV_GND ACV_UNREG V_OUT N.C. A_GND N.C. ACV_GND ACV_GND V_GND ACV_UNREG XMULTI_IN USB_GND USB_VBUS D+ ACV_GND ACV_GND N.C.(USB_VBUS) ACV_UNREG N.C. ACV_UNREG AV_JACK_IN AU_OUT_R USB_GND ACV_UNREG AU_OUT_L
XREC_MODE_LED_ON
XZOOM_T
XAE_LOCK_ON
XLCD_OPEN_SW
AF_LED_K
XRESET_SW
XPB_MODE_LED_ON
VL_3V
KEY_AD2
REG_GND
MIC_2.8V
XZOOM_W
XHYBLID_REC
KEY_AD_SHTL
AU_GND
XSHTR_ON
(KEY_AD4)
XCHARGE/XSTRB_LED
AU_GND
(KEY_AD3)
REG_GND
MIC_L
REG_GND
EVER_3.0V
MIC_R
KEY_AD1
AU_GND
D_2.8V
AF_LED_5V
REG_GND
XPWR_ON
EVER_3.0V
KEY_AD0
SYS_SO
MC_MSD3
BL_LEV
PANEL_2.8V
MC_MSBS
MC_MSCLK
XSYS_SCK
PANEL_G
PANEL_B
MC_MSD1
REG_GND
MS_PWR_ON
PANEL_V
MS_2.8V
REG_GND
XACCESS_LED
REG_GND
PANEL_R
BL_H
PANEL_8.5V
REG_GND
XMS_IN
MC_MSD2
XSYS_RST
MC_MSDIO
XPANEL_TG_CS
REG_GND
PANEL_5V
HDO
SYS_SI
BL_L
EVER_3.0V
XCHARGE/XSTRB_LED
AU_GND
XSHTR_ON
XAE_LOCK_ON
XZOOM_T
REG_GND
AF_LED_K
MIC_L
XREC_MODE_LED_ON
MIC_2.8V
XPB_MODE_LED_ON
KEY_AD1
XRESET_SW
XZOOM_W
KEY_AD2
MIC_R
REG_GND
REG_GND
XHYBLID_REC
AF_LED_5V
AU_GND
KEY_AD_SHTL
EVER_3.0V
AU_GND
REG_GND
VL_3V
KEY_AD0
XLCD_OPEN_SW
XPWR_ON
D_2.8V
SYS_SI
XSYS_RST
XSYS_SCK
PANEL_8.5V
MC_MSDIO
REG_GND
BL_H
HDO
MC_MSD1
MS_PWR_ON
PANEL_B
PANEL_R
MC_MSD2
MC_MSBS
REG_GND
XPANEL_TG_CS
MC_MSCLK
BL_LEV
REG_GND
PANEL_V
BL_L
SYS_SO
PANEL_2.8V
REG_GND
PANEL_5V
MS_2.8V
MC_MSD3
REG_GND
XACCESS_LED
XMS_IN
PANEL_G
REG_GND
LENSV_OUTB
LENSV_OPENSENS
REG_GND
LENSV_OUTB
LENSV_LED+
LENSV_OUTA
LENSV_OUTA
LENSV_OPENSENS
N.C.
REG_GND(N.C.)
XCHARGE/XSTRB_LED
D001_A
XREC_MODE_LED_ON
XPWR_ON
D003_A
XPB_MODE_LED_ON
REG_GND
D002_A
AF_LED_5v
AF_LED_K
REG_GND
PANEL_5V
BL_L
REG_GND
PANEL_G
BL_H
REG_GND
PANEL_R
PANEL_8.5V
XPANEL_TG_CS
BL_LEV
XSYS_RST
PANEL_2.8V
PANEL_V
SYS_SI
STATIC_GND
PANEL_B
XSYS_SCK
HDO
SYS_SO
KEY_AD_SHTL
REG_GND
KEY_AD0
KEY_AD1
D_2.8V
STATIC_GND
GND
SCLK
DATA1 DATA3
VCC
INT
BS
DATA2
GND
SDIO/DATA0
PANEL_V
HDO
PANEL_B
PANEL_2.8V PANEL_8.5V
XSYS_RST
PANEL_G
XSYS_SCK
BL_LEV
SYS_SO
BL_L
XPANEL_TG_CS
PANEL_R
PANEL_5V
REG_GND REG_GND
BL_H
REG_GND
STATIC_GND
SYS_SI
N.C.
MOVIE_SW
DISP_SW
REG_GND
REG_GND
PHOTO_SW
BL_L N.C. N.C. N.C. BL_H N.C.
KEY_A/DA(NC)
ACV_GND
KEY_A/DB(NC)
ACV_UNREG
A_OUT_L
XBATT_CHARGE(NC)
AV_JACK_IN ACV_UNREG
BATT_XEXT
FR_EXT_BATT(GND)
USB_VBUS
V_GND
V_OUT
XLANC_POWER_ON(NC)
FR_LOW_BATT(GND)
D+
USB_GND
A_OUT_R
ACV_GND
D-
ACV_UNREG
XMULTI_IN
USB_GND
ACV_GND
SHUTTLE
SW
FP-306
FLEXIBLE
BOARD FK-061
MA-155 HARNESS
PD-135 HARNESS
HARNESS
MIC_R
PM-046 BOARD
(1/2)LCD PANEL DRIVE
(2/2)MIC AMP
CONTROL
SWITCH
BLOCK
(PB80100)
SHEET KEY SW
CONTROL
SWITCH
COLOR
LCD
UNIT
BACK LIGHT UNIT
BLOCK
(TW80100)
ZOOM SW
MS-289 BOARD
(1/3)MS I/O CONNECTOR
(2/3)FUNCTION KEY
(3/3)CONNECTOR
16
HALL IC
FP-304
FLEXIBLE
BOARD
POWER SW
MOTOR UNIT
(PI(SENSOR) BOARD)
LENS BARRIER
FP-305
FLEXIBLE BOARD
SY-LD RELAY,SP
LENS UNIT
CAPACITOR
CCD IMAGER
FP-299
FLEXIBLE BOARD
CCD
IMAGER
FLASH UNIT
(FL80100)
FP-301 FLEXIBLE BOARD
MULTI CONNECTOR
LENSV_LED-
N.C.
N.C.
FP-300
FLEXIBLE
BOARD
BATTERY
TERMINAL
N.C.
N.C.
FP-307
FLEXIBLE BOARD
DC JACK
FP-302 FLEXIBLE BOARD SY(CN751)-MS(CN004) RELAY
FP-302 FLEXIBLE BOARD SY(CN752)-MS(CN006) RELAY
(1/11)CAMERA A/D CONV.TIMING GENERATOR
(2/11)LENS DRIVE
(3/11)CAMERA DSP,LENS CONTROL
(4/11)CAMERA SYSTEM CONTROL
(5/11)DIGITAL SIGNAL PROCESS
(6/11)SUPER AND FLASH MEMORY SDRAM
(7/11)HI CONTROL
(8/11)AUDIO AMP
(9/11)SPEAKER AMP
(10/11)CONNECTOR
(11/11)DC/DC CONVERTER
SY-133 BOARD
LITHIUM
BATTERY
(SECONDARY)
MEMORY STICK
DUO CONNECTOR
L
21
D
5
G
4
F
O
11 15
E
H
I
20
K
B
6 19
P
13 14
N
12
J
18 227102 1793
M
8
C
Q
16