Sony F35 Cinealta User manual

DIGITAL CINEMATOGRAPHY CAMERA
F35
MAINTENANCE MANUAL
Volume 1 1st Edition (Revised 1)
Serial No. 10001 and Higher

F35
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
For safety, do not connect the connector for peripheral device
wiring that might have excessive voltage to the following port(s).
: MODULAR JACK (TRANSFORMER INTERNAL TYPE)
Follow the instructions for the above port(s).

F35
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandé par le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
1 (P)

1
F35
Table of Contents
Manual Structure
Purpose of this manual ................................................................. 3
Related manuals ........................................................................... 3
1. Service Overview
1-1. Checking before Installation ........................................... 1-1
1-1-1. Checking the ROM and Software Version ............ 1-1
1-1-2. Checking the Software Version of SRW-1 ...........1-1
1-2. Connector and Cables .....................................................1-2
1-2-1. Connector Input/Output Signals ............................ 1-2
1-2-2. Wiring Diagrams for Cables ................................. 1-5
1-2-3. Connection Connectors/Cables ............................. 1-6
1-3. Location of Printed Circuit Boards ................................. 1-7
1-4. Removing/Reinstalling the Side Panel ........................... 1-8
1-5. Switch Settings ............................................................... 1-9
1-6. Cleaning the Ventilate Bracket of the Fan .................... 1-13
1-6-1. The Duct (LF) ...................................................... 1-13
1-6-2. The Rear Grille and the Rear Fan Shield ............ 1-13
1-6-3. The Rear Duct ..................................................... 1-13
1-7. Notes on Replacement of Circuit Board ....................... 1-14
1-7-1. Description on EEPROM Data ........................... 1-14
1-7-2. Adjustment after Replacement of Board .............1-14
1-7-3. Adjustment and Setting Items when Replacing
AT-173A Board ................................................... 1-14
1-8. Upgrading the Software ................................................1-15
1-8-1. Upgrading the MAIN CPU ................................. 1-15
1-8-2. Upgrading the NET CPU .................................... 1-15
1-9. Writing and Rewriting the PLD Internal Data .............. 1-16
1-10. Note on Replacement of Lithium Battery ..................... 1-16
1-11. Recommended Replacing Parts .................................... 1-17
1-12. Description of CCD Block Number ............................. 1-18
1-13. Optional Fixtures .......................................................... 1-18
1-14. Notes on Repair Parts ................................................... 1-18
1-15. Unleaded Solder ............................................................ 1-18
1-16. Circuit-Protection Part List ........................................... 1-19
2. Replacement of Main Parts
2-1. Replacing CCD Unit ....................................................... 2-1
2-2. Replacing CCD Unit Boards .......................................... 2-2
2-2-1. CN-3002 Flexible Board ....................................... 2-2
2-2-2. TG-258 Board ....................................................... 2-2
2-2-3. CN-2903 Flexible Board ....................................... 2-3
2-3. Replacing Fans ................................................................ 2-3
2-3-1. DC Fan (OHB) ...................................................... 2-3
2-3-2. DC Fan (Power Supply Unit) ................................2-6
2-3-3. DC Fans (Rear) ...................................................... 2-7
2-4. Replacing Parts in Inside Panel ...................................... 2-9
2-4-1. Replacing Inside Relay Board
(CN-2921 Board) ................................................... 2-9
2-4-2. Replacing Rotary Encoder (SW-1334 Board) ....... 2-9
2-4-3. Replacing VTR Start/Stop Switch
(SW-1336 Board) ................................................ 2-10
2-4-4. Replacing LOCK, VF MENU/DISPLAY, and
CANCEL/STATUS Switches
(CN-2997 Board) ................................................. 2-10
2-4-5. Replacing ASSIGNABLE Switch
(SW-1332 Board) ................................................ 2-10
2-4-6. Replacing MODE SET Switch
(SW-1333 Board) ................................................ 2-10
2-4-7. Replacing Fluorescent Indicator Tube ................ 2-11
2-5. Replacing Parts in Assistant Panel (Accessory) ........... 2-11
2-5-1. Replacing Inside Relay Board
(CN-2921 Board) ................................................. 2-11
2-5-2. Replacing Rotary Encoder (SW-1334 Board) .....2-12
2-5-3. Replacing VTR Start/Stop Switch
(SW-1336 Board) ................................................ 2-12
2-5-4. Replacing LOCK, VF MENU/DISPLAY, and
CANCEL/STATUS Switches
(CN-2997 Board) ................................................. 2-12
2-5-5. Replacing ASSIGNABLE Switch
(SW-1332 Board) ................................................ 2-13
2-5-6. Replacing MODE SET Switch
(SW-1333 Board) ................................................ 2-13
2-5-7. Replacing Fluorescent Indicator Tube ................ 2-13
2-6. Replacing Connectors ................................................... 2-14
2-6-1. Front Section ....................................................... 2-14
2-6-2. Rear Section ........................................................ 2-15
2-6-3. Top Section ......................................................... 2-17
2-6-4. Outside CN Assembly
(CN-2917 Board, CN-2996 Board) ..................... 2-17
2-6-5. IF BOX (accessory) ............................................. 2-18

2F35
2-7. Replacing Parts in Power Supply Section .................... 2-21
2-7-1. Replacing Power Supply Assembly
(PS-724 Board) .................................................... 2-21
2-7-2. Replacing Switching Regulator
(RE-241 Board) ................................................... 2-22
2-7-3. Replacing Fuses ................................................... 2-22
2-8. Replacing Leveler ......................................................... 2-22
2-9. Replacing Boards .......................................................... 2-24
2-9-1. Replacing TR-138 Board .................................... 2-24
2-9-2. Replacing DPR-283 board .................................. 2-25
2-9-3. Replacing MB-1100 Board ................................. 2-25
2-10. Disconnecting/Connecting Coaxial Cables .................. 2-26
2-10-1. Coaxial Cable with Connector ............................ 2-26
2-10-2. Coaxial Cable ...................................................... 2-27
2-11. Routing the Harness ...................................................... 2-28
2-11-1. Front (Left) .......................................................... 2-28
2-11-2. Inside Section ...................................................... 2-29
2-11-3. Rear Connector Box ............................................2-30
2-11-4. Outside Connector ............................................... 2-31
2-11-5. Outside Section ................................................... 2-32
3. Electrical Alignment
3-1. Preparations .................................................................... 3-1
3-1-1. Equipment Required .............................................. 3-1
3-1-2. Precautions on Adjustments ..................................3-1
3-1-3. File Data at Adjustment ......................................... 3-1
3-1-4. Gray-Scale Chart and its Maintenance .................. 3-2
3-1-5. Description on Setup Menu ................................... 3-3
3-1-6. Connection of Equipment ...................................... 3-4
3-1-7. Initial Settings ....................................................... 3-5
3-1-8. Adjustment Items and Setup Menu Items ............. 3-6
3-2. Automatic Adjustment .................................................... 3-7
3-3. Video System Level Adjustment ....................................3-7
3-3-1. H/V Ratio Adjustment ........................................... 3-7
3-3-2. Detail Level Adjustment ....................................... 3-8
3-3-3. Crispening Adjustment .......................................... 3-8
3-3-4. Level Dependent Adjustment ................................ 3-9
3-3-5. Detail Clip Adjustment .......................................... 3-9
3-3-6. Pedestal Level Adjustment .................................. 3-10
3-3-7. Flare Adjustment ................................................. 3-11
3-3-8. Gamma Correction Adjustment .......................... 3-11
3-3-9. Knee Point/Knee Slope Adjustment .................... 3-12
3-3-10. White Clip Level Adjustment ............................. 3-13
3-3-11. File Store ............................................................. 3-13
4. Service Menu
4-1. How to Display the Service Menu .................................. 4-1
4-2. Descriptions of Service Menu ........................................ 4-1

3
F35
Manual Structure
Purpose of this manual
There are the volume 1 and volume 2 in the Maintenance manual of F35.
The maintenance manuals (Volume 1, 2) are intended for use by trained system and
service engineers, and provides the information of maintenance and detailed service.
Related manuals
The following manuals are available in this model.
If this manual is required, please contact your local Sony Sales Office/Service Center.
..
..
.Operation Manual (Supplied with the unit)
This manual is necessary for application and operation (and installation) of this unit.
..
..
.Maintenance Manual
Volume 1: Describes about maintenance information, parts replacement, and
guideline for adjustment.
Part number: 9-968-430-0X
Volume 2: Describes about block diagrams, schematic diagrams and detailed parts
list required for parts-level service.
Part number: 9-968-340-0X
..
..
.“Semiconductor Pin Assignments” CD-ROM
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in Broadcast and Professional equipment.
This manual contains a complete list of semiconductors and their ID Nos., and
thus should be used together with the CD-ROM.
Part number: 9-968-546-06

F35 1-1
Section 1
Service Overview
1-1. Checking before Installation
1-1-1. Checking the ROM and Software Version
When connecting the peripheral equipment in the list below to F35, be sure to check
that the ROM and software version on each peripheral device is corresponding to the
camera to be connected.
If the ROM and software version is lower than the specified below, be sure to
perform ROM replacement and updating the software.
If ROM replacement and updating the software are required, contact your local Sony
Sales Office/Service Center.
ROM
Peripheral equipment Board name Ref No. Rom version
MSU-700A/750 CPU-293/CPU-286 IC5, IC6/IC5, IC6 Ver. 1.30 or higher
RM-B150 CPU-266 IC4 Ver. 1.00 or higher
Software
Peripheral equipment Board name Software version
RM-B750 MPU-124 Ver. 1.20 or higher
MSU-900/950 CPU-396 Ver. 1.20 or higher
n
Even when the ROM versions specified by MSU and RM in the table are used, the
shutter and ECS of F35 can be controlled, but the values cannot be displayed
correctly.
1-1-2. Checking the Software Version of SRW-1
When the SRW-1 mounted on the F35, be sure to check the software version on the
SRW-1.
The SRW-1 with the software ver. 2.30 or higher can be mounted on the F35.
If the software version is lower than ver. 2.30, contact your local Sony Sales Office/
Service Center.

F35
1-2
1-2. Connector and Cables
1-2-1. Connector Input/Output Signals
Connector Layout (F35: Camera)
Output signals
11
11
1HD-SDI A/B
HD SDI signal
BTA-S004A compliant
BNC type 75 Z, 0.8 V p-p 1.485 Gbps
22
22
2MONITOR HD-SDI 1/2
HD SDI signal
BTA-S004A compliant
BNC type 75 Z, 0.8 V p-p 1.485 Gbps
33
33
3TEST OUT
BNC type 75 Z, 1.0 V p-p
Input signal
44
44
4GENLOCK IN
BNC type 75 Z, 1.0 V p-p
4
3
2
2
5
!-
!]![!= !\
9
0
9
6
1
7(bottom)
(F35: Interface Box)

F35 1-3
55
55
5REMOTE (8P FEMALE)
(External view)
No. Signal I/O Specifications
1 TX (+) OUT SERIAL Data out
2 TX (_) OUT
3 RX (+) IN SERIAL Data in
4 RX (_)IN
5 TX-GND —— GND for TX
6 UNREG OUT +10.5 to +17 V dc, 200 mA (max)
7 UNREG-GND —— GND for UNREG
8 VIDEO OUT 75 Z, 1.0 V p-p
CHASSIS GND —— CHASSIS GND
66
66
6AUDIO IN CH-1/CH-2 (3P FEMALE)
(External view)
No. Signal I/O Specifications
1 AUDIO 1/2 (G) —— _44 dBu (for MIC)/
2 AUDIO 1/2 (X) IN +4 dBu (for LINE)
3 AUDIO 1/2 (Y) IN
(0 dBu = 0.775 Vrms)
77
77
7DC IN 10.5-17 V (4P MALE)
(External view)
No. Signal I/O Specifications
1 GND —— GND for DC (+)
2 NC No connection
3 NC No connection
4 DC (+)IN+10.5 to 17 V dc
17
6
5
4
3
2
8
21
3
99
99
9VF 1/2 (20P FEMALE)
(External view)
No. Signal I/O Specifications
1 S-DATA IN/OUT TTL level
2 NC No connection
3 NC No connection
4 SCK OUT TTL level
5 NC No connection
6 NC No connection
7 NC No connection
8 G TALLY OUT ON : 5 V
OFF : GND
9 NC No connection
10 NC No connection
11 NC No connection
12 Y VIDEO OUT 1.0 V p-p, Zo = 75 Z
13 VIDEO GND —— GND for VIDEO
14 Pb VIDEO OUT ±0.35 V p-p, Zo = 75 Z
15 Pr VIDEO OUT ±0.35 V p-p, Zo = 75 Z
16 NC No connection
17 R TALLY OUT ON : 5 V
OFF : GND
18 NC No connection
19 UNREG GND —— GND for UNREG
20 UNREG OUT +10.5 V to +17 V

F35
1-4
18
!=!=
!=!=
!= EXT I/O (5P FEMALE)
(External view)
No. Signal I/O Specifications
1 EXT_CMD1_OUT OUT RS-232C
2 EXT_CMD0_OUT OUT
3 EXT_CMD1_IN IN
4 EXT_CMD0_IN IN
5 GND ——
![![
![![
![ ETHERNET (MODULAR JACK)
IEEE 802.3u (100BASE-TX), IEEE 802.3 (10BASE-
T) compliant
(External view)
No. Signal I/O Specifications
1 TXD (+) OUT
2 TXD (_) OUT
3 RXD (+)IN
4NC _
5NC _
6 RXD (_)IN
7NC _
8NC _
1
52
3 4
!/!/
!/!/
!/ CTRL PANEL (14P FEMALE)
(External view)
No. Signal I/O Specifications
1 SIN OUT VFD_I/F
2 SBUSY IN VFD_I/F
3 XRESET OUT VFD_I/F
4 RE_B IN
5 RE_A IN
6 IIC_DATA IN/OUT TTL level
7 IIC_CLK OUT TTL level
8 POWER OUT +7 V 500 mA (MAX)
9 GND ——
10 NC
11 AUX1 IN OPEN or +5 V : Normal
GND : Active
12 AUX2 IN OPEN or +5 V : Normal
GND : Active
13 AUX3 IN OPEN or +5 V : Normal
GND : Active
14 NC
!-!-
!-!-
!- DC IN (8P MALE)
(External view)
No. Signal I/O Specifications
1 UNREG_GND —— GND for +12 V
2 UNREG_GND —— GND for +12 V
3 UNREG_GND (24 V) —— GND for +24 V
4 UNREG_24 V_IN IN +20 to +30 V
5 UNREG_12 V_IN IN +10.5 to +17 V
6 UNREG_12 V_IN IN +10.5 to +17 V
7 UNREG_12V_IN IN +10.5 to +17 V
8 UNREG_GND —— GND for +12 V
11
14 83
74
65
92
101
13
12
1
5
2
3
4
8
7
6

F35 1-5
!]!]
!]!]
!] DC OUT 12 V (11P FEMALE)
(External view)
No. Signal I/O Specifications
1NC
2NC
3NC
4NC
5NC
6NC
7NC
8NC
9 UNREG_GND ——
10 NC
11 UNREG_12 V_OUT OUT +10.5 to +17 V dc
5.0 A (MAX)
!\!\
!\!\
!\ DC OUT 24 V (3P FEMALE)
(External view)
No. Signal I/O Specifications
1 UNREG_GND (24 V) ——
2 UNREG_24 V_OUT OUT +20 to +30 V dc
5.0 A (MAX)
3 REC trigger IN OPEN or +5 V : Normal
GND : Active
10
1
6
5
4
3
11 9
2
8
7
1
3
2
1-2-2. Wiring Diagrams for Cables
CCA-5 Cable
BrownBrown
Brown
Red
Red
White
White
White
Orange
Black
—8P CONNECTOR (MALE) —
(WIRING SIDE)

F35
1-6
1-2-3. Connection Connectors/Cables
Connection made with the connector panels during instal-
lation or service, should be made with the connectors/
complete cable assemblies specified in the following list,
or equivalent parts.
Indication Connection connector/cable
HD-SDI A/B 1-569-370-12 Plug, BNC
MONITOR HD-SDI 1/2
TEST OUT
GENLOCK IN
(BNC)
AUDIO IN CH-1/CH-2 1-508-084-00 XLR, 3P Male or
(3P FEMALE) ITT Cannon XLR-3-12C equivalent
DC OUT 12 V FISCHER S104A056-130 or equivalent
(11P FEMALE)
DC OUT 24 V FISCHER S102A052-130 or equivalent
(3P FEMALE)
DC IN 1-508-362-00 XLR, 4P Female or
(4P MALE) ITT Cannon XLR-4-11C equivalent or
Cable assembly
(Supplied with AC-550/550CE)
1-551-577-00
DC IN 1-821-089-11 or
(8P MALE) LEMO FGJ, 3B, 308, CYMD82
REMOTE .1-766-848-11 Plug, 8P Male or
(8P FEMALE) CCA-5 cable assembly
(CCA-5-10 (10 m) /CCA-5-3 (3 m))
(option)*2 *3
.REMOTE cable 1-783-372-11
(Supplied with RM-B150, 10 m) *1 *2 *3
CTRL PANEL 1-833-942-11 CORD, CONNECTION
(14P FEMALE) (ROUND TYPE) or
LEMO FGB, 1B, 314, CYCD62
EXT I/O LEMO FGC, 1B, 305, CLADXX *4
(5P FEMALE)
*1: Use of REMOTE cable enables to monitor video signals. (The pin 8 is
available for the video signal line.)
HD-Y signal or the down-converted SD signal is output. (It is possible to
select it by the menu.)
*2: If using a cable of length different from a standard product, contact your
local Sony Sales Office/Service Center.
m
*3: The pin 8 of CCA-5 cable is GND (ground).
The pin 8 of REMOTE cable is not GND (ground).
*4: XX indicates the cable diameter.

F35 1-7
CN-2921
SW-1334
CN-2997
AT-173A
RE-241
SW-1332
CN-3000
VDA-67
VDA-68
CN-2904
LP-119
DPR-283
CN-2915
RE-253
TR-138
AD-180
CN-2913
CN-3088
MB-1100
LP-120
CN-2917
CN-2996
CN-2999
RE-252 SW-1336
BI-205
SK-23
CN-2903
CN-3002
TG-258
CN-2916
SW-1333
RE-253
CN-2920
PS-724
CN-2921
SW-1336
Assistant panel
(Supplied accessory)
CN-2909
ENC-105
CN-2908
SW-1332
CN-2997
SW-1334
SW-1333
IF box
(Supplied accessory)
1-3. Location of Printed Circuit Boards

F35
1-8
1-4. Removing/Reinstalling the Side
Panel
1. Unscrew the four screws with stopper on the inside
panel assembly.
2. Disconnect the board to board connector (CN1) on the
CN-2921 board, and remove the inside panel assem-
bly.
3. Remove the four screws, and remove the four BNC
caps.
4. Remove the screw, and remove the REMOTE (CN)
cap.
5. Remove the DC-IN nut.
6. Remove the two screws, and remove the outside
connector cap.
7. Unscrew the four screws with stopper, and remove the
outside panel assembly.
8. Reinstall the panels by reversing the steps above.
Screws with
stopper
Screws with
stopper
Screws with stopper
Screws with stopper
Outside panel
assembly
Inside panel assembly
CN-2921 board
(CN1)
DC-IN nut
DC-IN nut
BNC cap
REMOTE (CN)
cap
Screw (M2)
M2 screw
Outside conector cap
Screw
(M2)

F35 1-9
1-5. Switch Settings
AD-180 Board
Ref. No. Name Description Factory setting
SW1-1 SW1 Selection of the JTAG CONF ON
SW1-2 SW0 Not used (Fixed to OFF) OFF
SW1
ABCDE
1
2
3
4
AD-180 BOARD (SIDE A)

F35
1-10
AT-173A Board
Ref. No. Name Description Factory setting
S301-1 COM Not used (Fixed to OFF) OFF
S301-2 RS-232C Not used (Fixed to ON) ON
S301-3 Reserve Not used (Fixed to OFF) OFF
S301-4 Reserve Not used (Fixed to OFF) OFF
S302-1 Reserve Not used (Fixed to OFF) OFF
S302-2 All Preset FRAM CLEAR OFF
S302-3 Main Forcibly upgrading of Main, Boot Program OFF
S302-4 PLD Selection of the AT PLD JTAG CONF. ON
OFF: Download Tool, ON: Memory Stick
S800-1 CLK 1/2 Not used (Fixed to OFF) OFF
S800-2 DEB ROM Not used (Fixed to OFF) OFF
S800-3 DEB NMI Not used (Fixed to OFF) OFF
S800-4 HIFB Not used (Fixed to OFF) OFF
S801 Reset Not used (Fixed to OFF) OFF
S301
S302
S800
AB
CD
1
2
3
AT-173A BOARD (SIDE A)
S801
AB
C
D
1
2
3
AT-173A BOARD (SIDE B)

F35 1-11
DPR-283 Board
Ref. No. Name Description Factory setting
S5001-1 SW0 Selection of the JTAG CONF. OFF
S5001-2 SW1 Selection of the JTAG CONF. OFF
S5001-3 SW2 Not used (Fixed to OFF) OFF
S5001-4 SW3 Not used (Fixed to OFF) OFF
TR-138 Board
Ref. No. Name Description Factory setting
S2001-1 SW0 Selection of the JTAG CONF. OFF
S2001-2 SW1 Selection of the JTAG CONF. OFF
S2001-3 SW2 Not used (Fixed to OFF) OFF
S2001-4 SW3 Not used (Fixed to OFF) OFF
S5001
ABCDE
1
2
3
4
5
DPR-283 BOARD (SIDE A)
S2001
ABCDE
1
2
3
4
TR-138 BOARD (SIDE A)

F35
1-12
VDA-67 Board
Ref. No. Name Description Factory setting
S200-1 EXT I05 Not used (Fixed to OFF) OFF
VDA-68 Board
Ref. No. Name Description Factory setting
S801-1 SW0 Selection of the JTAG CONF. OFF
S801-2 SW1 Selection of the JTAG CONF. OFF
S801-3 SW2 Not used (Fixed to OFF) OFF
S801-4 SW3 Not used (Fixed to OFF) OFF
S200
ABCDE
1
2
3
4
VDA-67 BOARD (SIDE A)
S801
ABC
VDA-68 BOARD (SIDE A)