Sony ILCE-3000K User manual

ILCE-3000K/3500J_L2 Sony Corporation
SERVICE MANUAL
Revision History
SERVICE NOTE (Check the following note before the service.)
LEVEL 2
983474133.pdf
2014D08-1
© 2014.04
Published by Sony Techno Create Corporation
Ver. 1.2 2014.04
INTERCHANGEABLE LENS DIGITAL CAMERA
US Model
Canadian Model
AEP Model
UK Model
Russian Model
E Model
Australian Model
Chinese Model
Korea Model
Brazilian Model
Tourist Model
1-1. PRECAUTION ON REPLACING THE SY-1026 BOARD
1-2. ADDITION OF DESTINATION DATA FILE
9-834-741-33
[About the service of this model]
ILCE-3000K/3500J are commodity that packed the Interchangeable Lens Digital Camera and Interchangeable Lenses.
Refer to each following service manual the Interchangeable Lens kit, when you repair.
Model Lens Service Manual of Lens
ILCE-3000K SEL1855 (E 18-55 mm F3.5-5.6 OSS) 9-852-799-[][]
ILCE-3500J SEL1850 (E 18-50 mm F4-5.6) 9-834-791-[][]
Ver. Date History Contents S.M. Rev.
issued
1.0 2013.08 Official Release — —
1.1 2013.09 Supplement-1
(S1 13-086)
• Revision of EXPLODED VIEWS.
• Addition of ASSEMBLY.
Yes*
1.2 2014.04 Revised-1
(A1 13-201)
• Addition of ILCE-3500J.
Page 2, 2-5, 2-9
Yes
The components identified
by mark 0or dotted line with
mark 0are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
ILCE-3000K/3500J
*: S.M. revised only top cover.
Photo: ILCE-3000K
Revised-1
Replace the previously issued
SERVICE MANUAL 9-834-741-32
with this Manual.

ILCE-3000K/3500J_L2
– 2 –
SPECIFICATIONS
Camera
[System]
Camera type: Interchangeable lens
digital camera
Lens: E-mount lens
[Image sensor]
Image sensor: APS-C format
(23.2 mm × 15.4 mm) CMOS
image sensor
Total pixel number of image sensor:
Approx. 20 400 000 pixels
Effective pixel number of camera:
Approx. 20 100 000 pixels
[Auto focus system]
System: Contrast detection system
Sensitivity range: EV0 to EV20 (at ISO
100 conversion, with F2.8 lens)
[Exposure control]
Metering method: 1 200-segment
metering by the image sensor
Metering range: EV0 to EV20 (at ISO
100 conversion, with F2.8 lens)
ISO sensitivity (Recommended
exposure index):
Still images: AUTO, ISO 100 –
ISO 16000
Movies: AUTO, ISO 100 –
ISO 3200 equivalent
Exposure compensation:
±3.0 EV (1/3 EV step)
[Shutter]
Type: Electronically-controlled,
vertical-traverse, focal-plane type
Speed range:
Still images: 1/4 000 second to
30 seconds, BULB
Movies: 1/4 000 second to
1/4 second (1/3 EV step),
1080 60i-compatible device up to
1/30 second in AUTO mode
1080 50i-compatible device up to
1/25 second in AUTO mode
Flash sync speed: 1/160 second
[Recording media]
“Memory Stick XC Duo” media,
“Memory Stick PRO Duo” media,
SD card
[Electronic viewfinder]
Type: Electronic viewfinder
Screen size: 0.5 cm (0.20 type)
Total number of dots:
201 600 dots equivalent
Frame coverage: 100%
Magnification: 0.70 × with 50 mm lens
at infinity, –1 m–1 (diopter)
Eye point: Approx. 21 mm from the
eyepiece, 15 mm from the eyepiece
frame at –1 m–1 (diopter)
Diopter adjustment:
–4.0 m–1 to +3.5 m–1 (diopter)
[LCD screen]
LCD panel: Wide, 7.5 cm (3.0 type)
TFT drive
Total number of dots: 230 400 dots
[Input/output terminals]
Multi/Micro USB Terminal*:
USB communication
* Supports Micro USB compatible device.
[Power]
Battery type: Rechargeable battery
pack NP-FW50
[Power consumption]
When using an E 18-55 mm F3.5-5.6
OSS lens
When using the viewfinder:
Approx. 2.0 W
When using an LCD screen:
Approx. 1.9 W
[Others]
Exif Print: Compatible
PRINT Image Matching III:
Compatible
DPOF: Compatible
Dimensions (CIPA compliant)
(Approx.):
128.0 mm × 90.9 mm × 84.5 mm
(5 1/8 inches × 3 5/8 inches ×
3 3/8 inches) (W/H/D)
Mass (CIPA compliant) (Approx.):
411 g (14.5 oz) (including battery
and “Memory Stick PRO Duo”
media)
353 g (12.5 oz) (camera only)
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
File format:
Still image: JPEG (DCF Ver. 2.0,
Exif Ver. 2.3, MPF Baseline)
compliant, RAW (Sony ARW
2.3 Format)
Movie (AVCHD format): AVCHD
format Ver. 2.0 compatible
Video: MPEG-4 AVC/H.264
Audio: Dolby Digital 2ch
Dolby Digital Stereo Creator
• Manufactured under license from Dolby
Laboratories.
Movie (MP4 format):
Video: MPEG-4 AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
USB communication:
Hi-Speed USB (USB 2.0)
[Flash]
Flash guide number:
4 (in meters at ISO 100)
Recycling time: Approx. 4 seconds
Flash coverage: Covering 16 mm lens
(focal length that the lens indicates)
Flash compensation:
±2.0 EV (1/3 EV step)
Rechargeable battery pack
NP-FW50
Battery type: Lithium-ion battery
Maximum voltage: DC 8.4 V
Nominal voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
Minimum 7.3 Wh (1 020 mAh)
Maximum dimensions (Approx.):
31.8 mm × 18.5 mm × 45 mm
(1 5/16 inches × 3/4 inches ×
1 13/16 inches) (W/H/D)
Mass (Approx.): 57 g (2.1 oz)
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health
and environment, and wastes resources.
Manage the chemicals carefully as follows.
• Store chemicals sealed in a specific place to prevent from exposure
to high temperature or direct sunlight.
• Avoid dividing chemicals into excessive numbers of small containers
to reduce natural evaporation.
• Keep containers sealed to avoid natural evaporation when chemicals
are not in use.
• Avoid using chemicals as much as possible. When using chemicals,
divide only required amount to a small plate from the container and
use up it.
EXTERIOR PARTS
Be careful to the following points for plastic parts used in this unit.
• Use a piece of cleaning paper or cleaning cloth for cleaning plastic
parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint
thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a
plastic part.
Be careful not to tighten screws too much.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 350°C during
repairing.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350°C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenom-
enon.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
Model information table
Model ILCE-3000K ILCE-3500J
Destination US, CND, E, KR, BR AEP, UK, RU, E, AUS, CH, JE US, CND, E, BR RU, E, AUS
Color system NTSC PAL NTSC PAL
Lens E 18-55 mm F3.5-5.6 OSS E 18-55 mm F3.5-5.6 OSS E 18-50 mm F4-5.6 E 18-50 mm F4-5.6
• Abbreviation
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
JE : Tourist model
KR : Korea model
RU : Russian model
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.2 2014.04

ILCE-3000K/3500J_L2
1-1
1. SERVICE NOTE
1-1. PRECAUTION ON REPLACING THE SY-1026 BOARD
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference
from the ID registered by the customer.
1-2. ADDITION OF DESTINATION DATA FILE
If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
Note 1: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
Install the Adjust manual of the DSC-WX50 series in advance.
Note 2: The actual image may differ from the image shown above.
1) If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed.
Click the [OK] button.
Fig. 1
2) The Destination Data Write window opens.
Check the version of the Destination Data file retained in the Adjust manual.
Destination Ver. window
3) Search the model whose new Destination Data file you want to get on the TISS homepage.
When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered.
(Example) Destination File For DSC-WX50.zip
Furthermore, the version supported by the Destination Data file is shown in the Remarks column.
Note : If the Destination Data file has not been updated, contact the Service Headquarters.
4) Download the Destination Data file of the relevant model and unzip the file.
5) Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual.
Click the [START] button.

ILCE-3000K/3500J_L2
1-2E
6) Click the [File Update] button in the window.
7) A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
8) When the file has been successfully added, the following window opens.
9) Check the Destination Ver. window and confirm that the version has been updated.
Destination Ver. window

ILCE-3000K/3500J_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link ACCESSORIES
DISCHARGING OF THE CHARGING CAPACITOR ASSEMBLY
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the
original one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from the
parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: μF
• COILS
uH: μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...: μA... , uPA... , μPA... ,
uPB... , μPB... , μPC... , μPC... ,
uPD..., μPD...
The components identified by mark 0or dotted line
with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le nu-
méro spécifié.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instruc-
tions.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
• Abbreviation
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
JE : Tourist model
KR : Korea model
RU : Russian model
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
1Cabinet (Rear) Assy
2Base (JK) Assy
3Control Switch Block
6Base (SW) Assy
qa Cover (ST)
qs ST Block
5Frame (Main) Assy
7SY-1026 Board
8IS-105 Flexible Board
9IS-1006 Flexible Board
q; Base (Main) Block
• LC-1012 Flexible Board
• BT-2002 Flexible Board
qd Imager Block
• IS-1007 Board
4Shoe Block
• MIS-2002 Flexible Board
• HB-1002 Flexible Board
• ST-1017 Flexible Board
qf RL Block
• RL-1023 Flexible Board
qg Cabinet (Front) Assy

ILCE-3000K/3500J_L2
2-2
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
NG
(The flexible board was plugged in
crooked.)
NG
(The flexible board was not plugged in
completely.)
Flexible
Board Flexible
Board
Connector Connector
Reference line Flexible
Board
Connector Connector
Flexible
Board
Reference line
Connector Connector
Flexible
Board
Flexible
Board
Reference line
Fig. 1 Fig. 2 Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
Holder
Connector Flexible Board
A
AHolder
Insulation side
Connector Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.
DISCHARGING OF THE CHARGING
CAPACITOR (C901)
R:1 kΩ/ 1 W
(Part code: 1-215-869-11)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
ST-1017 Flexible Board
Discharge lands
Claw
Release the claw holding this part of the Flexible Board
paying attention not to touch the discharge lands on the
back of the Flexible Board.
Claw
ST-1017 Flexible Board
C901
Be careful not to break the flexible board.
The charging capacitor is charged up to the maximum 315 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
1kΩ/1 W
Wrap insulating tape.
1kΩ/1 W
Wrap insulating tape.
SUBSIDIARY MATERIALS
G: Grease
G-85 (J-6082-626-A)

ILCE-3000K/3500J_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No. Part No. Description Ref. No. Part No. Description
1 X-2587-856-1 BASE (JK) ASSY (771)
2 A-1959-442-A MIS-2002 FLEXIBLE BOARD, COMPLETE
3 4-471-845-01 BASE (SHOE) (771)
4 4-471-846-01 PLATE (SHOE) (771)
5 1-489-775-51 SWITCH BLOCK, CONTROL
6 4-484-055-01 SHEET (WS) (771) (Note)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
DISASSEMBLY
1. Remove in numerical order (1to 5) in the left figure.
1#2 X 6 →#12 X 1 →Open the JK lid (1) →#2 X 3
Bottom View Left View Back View Right View
#2 #2
#2
#12 #2
1
#2
(Note)
#2
#2
#12
Claws
#12
#2
#2
#1
2
Bosses
5
2
35
21
46
3
4
1Rear Section
(See page 2-8)
Main Board Section
(See page 2-4)
1
5#12 X 4
Back View #12
#12
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
Note 1: Refer to “Assembly-7: Notes on Assembling the Sheet (WS)
(771)” when assembling.
Note

ILCE-3000K/3500J_L2
2-4
2-1-2. MAIN BOARD SECTION DISASSEMBLY
1. Remove in numerical order (1to 8) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇: Solder
Ref. No. Part No. Description Ref. No. Part No. Description
51 X-2587-854-1 BASE (MAIN) ASSY (771)
52 4-456-090-01 SPRING (BT DISCHARGE) (762)
53 A-1923-785-A BT-2002 FLEXIBLE BOARD, COMPLETE
54 1-885-294-11 IS-105 FLEXIBLE BOARD
55 1-887-267-11 IS-1006 FLEXIBLE BOARD
*56 4-471-842-01 PLATE (FRONT) (771)
57 A-1958-136-A SY-1026 BOARD, COMPLETE (SERVICE)
58 X-2587-852-1 BASE (SW) ASSY (771)
*59 X-2587-855-1 FRAME (MAIN) ASSY (771) (Note 1)
60 4-192-233-01 BD TRIPOD
61 4-484-056-01 SHEET (SY) (771) (Note 2)
BT901 1-780-858-11 TERMINAL BOARD BATTERY
SP901 1-858-343-71 LOUDSPEAKER (1.0CM)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
4#2 X 1
Back View
#2
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
1Disengage the flexible harnesses (1) →#12 X 3
Harnesses
Claw
Back View
#12
#12
2Disengage the flexible board (2)
Boss Flexible board
Claws
7#12 X 2
Back View
#12
#12
#12
SP901
#12
#12
#1
2
(Note 1)
(Note 2)
Claws
Claw
#2
D
BA
C
E


BT901
A
B
E
A
C
D
B
E
159
258
361
457
5
8
54
655
56
60
53
52
751
ST Section
(See page 2-5)
2
1
DISCHARGING OF THE CHARGING CAPACITOR
8
Note 1: Refer to “Assembly-1: Notes on Assembling the ST Block”
when assembling.
Note
Note 2: Refer to “Assembly-8: Notes on Assembling the Sheet (SY)
(771)” when assembling.

ILCE-3000K/3500J_L2
2-5
2-1-3. ST SECTION
ns: not supplied
DISASSEMBLY
1. Remove in numerical order (1to 5) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇: Solder
1Pop-up the flash ( 1 ) →#12 X 1
Screw
Front View
Flash pop-up button
#12 1
Ref. No. Part No. Description Ref. No. Part No. Description
101 4-471-841-01 COVER (ST) (771)
102 X-2587-847-1 CABINET (FRONT) ASSY (771) (3000K)
102 X-2589-636-1 CABINET (FRONT) ASSY (771) (3500J)
103 A-1957-983-A RL-1023 FLEXIBLE BOARD, COMPLETE (Note 2)
104 4-471-840-01 BASE (RL) (771)
105 X-2587-853-1 ST ASSY (771)
107 1-490-083-11 FLASH UNIT
108 1-888-083-11 HB-1002 FLEXIBLE BOARD
110 A-1957-984-A ST-1017 FLEXIBLE BOARD, COMPLETE
111 1-969-002-11 HARNESS (SK-1001) (Pink)
112 1-969-004-11 HARNESS (SK-1003) (Orange)
113 1-969-003-11 HARNESS (SK-1002) (White)
114 4-531-185-01 CLIP (MD) (771)
BH001 1-251-928-21 SOCKET, BATTERY (Note 1)
BT001 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
C901 1-100-936-11 ELECT 85uF 315V
MIC901 1-542-967-11 MICROPHONE UNIT
#12 3-080-204-21 SCREW, TAPPING, P2
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
Note
Note 1: Replace the battery holder (BH001) together when replac-
ing the lithium battery (BT001) on the RL-1023 board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium battery next.
Note 2: Refer to “Assembly-2: Notes on Assembling the RL Block”
when assembling.
#12




#12
Bosses
#12
#12
ns
#12
A
A
1
5
101
4104
114
103
(Note 2)
2105
110
3Imager Block Section
(See page 2-6)
1,2-1,2-2,
2-3
: BT001 (lithium battery)
Board on the mount position.
(See page 6-34 of Level 3)
112
(Orange)
111
(Pink)
113
(White)
107
102
108
MIC901
BT001
(Note 1)
BH001
(Note 1)
ns
C901
2 #12 X 1 →Disengage the harnesses (2-1) →Push down the flash (2-2) →Disengage the bosses (2-3)
Back View
#12 2-2
2-1
2-3
Bosses
3#12 X 2
Back View
#12
4#12 X 2
Back View
#12
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.2 2014.04

ILCE-3000K/3500J_L2
2-6
2-1-4. IMAGER BLOCK SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
151 A-1954-964-A SERVICE, MECHA DEVICE (1100)
(including CP6001 (CMOS imager) and IS-1007 complete
board) (Note 5)
152 4-430-446-01 SHEET (IS (720)), RADIATION
*153 Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
*154 Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
*155 Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
156 A-1905-698-A MB CHARGE UNIT (762) (Note 4)
157 1-492-255-11 SHUTTER UNIT (H129)
158 A-1932-986-A MB N HOLDER ASSY (SERVICE 762)
*159 4-186-538-01 SPRING, LENS LOCK
160 X-2586-035-1 MB L LOCK PIN ASSY (762)
161 4-456-086-01 BUTTON, LENS LOCK
*162 4-185-963-01 MB N PLATE SP (Note 7)
163 4-284-623-01 MB N PLATE (B) 755
164 4-283-999-03 MB N PLATE A (754)
165 4-188-536-01 CAP, BODY (Note 6)
#64 2-666-551-21 SCREW, TAPPING, P2
#197 4-185-990-01 MB SCREW, CHARGE UNIT FIXED
#230 4-287-434-01 TAPPING (1.7 (ECOLOGY))
DISASSEMBLY
1. Remove in numerical order (1to 2) in the left figure.
Screw
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
5.0
1.7
1#64 X 3
#64
Back View
2#230 X 3
#197: M1.6 X 4.5 (Tapping)
4.5
1.6
(Silver)
4-185-990-01
#230: M1.7 X 4.0 (Tapping)
(Black)
4-287-434-01
4.0
1.7
Note 1: Refer to “Assembly-3: Screw tightening sequence when
assembling the Radiation Plate (IM)” when assembling.
Note 2: The IM adjust washers (A, B, C) differ in thickness.
Make sure to return the removed IM adjust washers to origi-
nal places.
When replacing IM adjust washers, refer to “2-2. SELEC-
TION PARTS” on page 2-9.
If the original state cannot be restored due to loss of the
IM adjust washer, for example, replace the Mecha Device
(1100) (Service).
Note 3: Refer to “Assembly-4: IM Adjust Washer (A, B, C) putting
position” when assembling.
Note 4: Refer to “Assembly-5: Screw tightening sequence when
assembling the MB Charge Unit” when assembling.
Note 5: Precautions for Replacement of the Mecha Device
(1100) (Service).
As Mecha Device (1100) (Service) may be damaged by
static electricity from its structure, handle it carefully like for
the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
#230
Back View
Note 6: The Mecha Device (1100) (Service) includes a protective
Body Cap.
This part is supplied only with the Mecha Device (1100)
(Service).
Note 7: Refer to “Assembly-6: Apply grease on the MB N Plate SP”
when assembling.
Note
152
153
(Note 2, 3)
154
(Note 2, 3)
155
(Note 2, 3)
2156
(Note 4)
157
163
164
165
(Note 6)
158
159
160
161
1ns
(Note 1)
Imager Unit Section
(See page 2-7)
151
(including CP6001 (CMOS imager)
and IS-1007 complete board)
(Note 5)
#64
#64
#230
#197
ns
162
(Note 7)

ILCE-3000K/3500J_L2
2-7
2-1-5. IMAGER UNIT SECTION
ns: not supplied
Ref. No. Part No. Description
201 4-281-914-01 IM SPACER (869)
202 4-281-915-01 IM GS TAPE
203 1-856-482-11 FILTER BLOCK, OPTICAL (Note)
#191 4-188-735-01 SCREW (M1.7)
Screw
Note
Note :
J-6082-737-A
Refer to the following statements when replacing the Optical
filter block.
Method of Removal
(1) Pour resolvent (alcohol or cleaning agent) between the
imager and the IM spacer.
∗Wait for that the adhesive power of the IM spacer
weakens.
(2) Remove the IM spacer from the imager.
Method of Attachment
(1) Attach the IM GS tape and the Optical filter block by
aligning them with the outer shape of the IM spacer
evenly.
∗The two-layer side of the Optical filter block is on the
imager side.
(2) Set the Optical filter block in its attachment jig
(J-6082-737-A), with the attached adhesive face of IM
spacer facing upward.
(3) Press the imager down into the jig as shown below to
attach it to the Optical filter block.
Imager
Peel off the released paper.
Pour resolvent (alcohol or cleaning agent)
between the imager and the IM spacer.
The two-layer
side is on the
imager side.
Mount
Side
Imager
Side
Optical Filter Block
Peel off the
released paper.
Peel off the
released paper.
Peel off the
released paper.
IM GS Tape
IM Spacer
#191: M1.7 X 3.5
(Black)
4-188-735-01
3.5
1.7
201
202
203
(Note)
ns
ns
#191
(All mounted parts and IS-1007 complete board are not supplied,
but they are included in Mecha Device (1100) (Service).)

ILCE-3000K/3500J_L2
2-8
2-1-6. REAR SECTION
Ref. No. Part No. Description Ref. No. Part No. Description
251 A-1957-985-A LC-1012 FLEXIBLE BOARD, COMPLETE
252 4-279-877-01 RETAINER, MODULE
253 X-2581-259-1 VF ASSY (970)
254 X-2587-851-1 CABINET (REAR) ASSY (771)
255 4-471-844-01 SHEET (LC) (771), ADHESIVE
256 4-471-843-01 WINDOW (LC) (771)
LCD901 1-811-501-11 PANEL MODULE (PE1-WBCP)
LCD902 1-811-013-11 LCD MODULE (FL0906)
#12 3-080-204-21 SCREW, TAPPING, P2
Screw
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
251
#12
Claw
Claw
Claws
254
255
256
LCD901
LCD902
253
252

ILCE-3000K/3500J_L2
2-9E
ACCESSORIES
901 902 903 904 905
906 907 908 909 910 (Note)
Ref. No. Part No. Description
901 1-490-429-21 AC adaptor AC-UB10C/UB10D (US, CND)
901 1-490-429-31 AC adaptor AC-UB10C/UB10D (CH)
901 1-490-429-51 AC adaptor AC-UB10C/UB10D (BR)
901 1-490-429-61 AC adaptor AC-UB10C/UB10D (EXCEPT US, CND, CH,
BR)
902 1-836-411-21 Power cord (mains lead) (JE)
902 1-837-424-11 Power cord (mains lead) (E: NTSC)
902 1-837-427-11 Power cord (mains lead) (AEP, UK, RU, AUS, E)
902 1-837-428-11 Power cord (mains lead) (KR)
902 1-837-801-12 Power cord (mains lead) (BR)
903 1-569-007-31 Conversion (2P) Adaptor (E: NTSC, JE)
904 1-569-008-12 Conversion (2P) Adaptor (AUS, E)
905 1-846-486-11 Micro USB cable
906 X-2546-071-1 Front lens cap (3000K)
906 X-2582-535-2 Front lens cap (3500J)
907 4-159-703-02 Lens hood (3000K)
907 4-452-476-02 Lens hood (3500J)
908 4-196-660-11 Shoulder strap
909 4-469-858-11 Instruction Manual (ENGLISH) (3000K)
*909 4-469-858-21 Instruction Manual (FRENCH) (3000K)
*909 4-469-858-31 Instruction Manual (SPANISH, PORTUGUESE) (3000K)
*909 4-469-858-41 Instruction Manual (ENGLISH, FRENCH, GERMAN,
SPANISH, ITALIAN, PORTUGUESE, DUTCH, POLISH,
SWEDISH, FINNISH, NORWEGIAN, DANISH) (3000K)
909 4-469-858-51 Instruction Manual (TRADITIONAL CHINESE,
SIMPLIFIED CHINESE) (3000K)
*909 4-469-858-61 Instruction Manual (RUSSIAN, UKRAINIAN) (3000K)
*909 4-469-858-71 Instruction Manual (ARABIC, PERSIAN) (3000K)
909 4-469-858-81 Instruction Manual (KOREAN) (3000K)
*909 4-469-858-91 Instruction Manual (SIMPLIFIED CHINESE) (3000K)
*909 4-536-697-11 Instruction Manual (ENGLISH) (3500J)
*909 4-536-697-21 Instruction Manual (FRENCH) (3500J)
*909 4-536-697-31 Instruction Manual (SPANISH, PORTUGUESE) (3500J)
*909 4-536-697-41 Instruction Manual (TRADITIONAL CHINESE,
SIMPLIFIED CHINESE) (3500J)
*909 4-536-697-51 Instruction Manual (RUSSIAN, UKRAINIAN) (3500J)
*909 4-536-697-61 Instruction Manual (ARABIC, PERSIAN) (3500J)
*910 4-469-855-11 αHandbook (ENGLISH) (3000K) (Note)
*910 4-469-855-21 αHandbook (FRENCH) (3000K) (Note)
*910 4-469-855-31 αHandbook (ITALIAN) (3000K) (Note)
Ref. No. Part No. Description
*910 4-469-855-41 αHandbook (SPANISH) (3000K) (Note)
*910 4-469-855-51 αHandbook (PORTUGUESE) (3000K) (Note)
*910 4-469-855-61 αHandbook (GERMAN) (3000K) (Note)
*910 4-469-855-71 αHandbook (DUTCH) (3000K) (Note)
*910 4-469-855-81 αHandbook (TRADITIONAL CHINESE) (3000K) (Note)
*910 4-469-855-91 αHandbook (SIMPLIFIED CHINESE) (3000K) (Note)
*910 4-469-856-11 αHandbook (RUSSIAN) (3000K) (Note)
*910 4-469-856-21 αHandbook (ARABIC) (3000K) (Note)
*910 4-469-856-31 αHandbook (PERSIAN) (3000K) (Note)
*910 4-469-856-41 αHandbook (KOREAN) (3000K) (Note)
*910 4-469-856-51 αHandbook (POLISH) (3000K) (Note)
*910 4-469-856-61 αHandbook (CZECH) (3000K) (Note)
*910 4-469-856-71 αHandbook (HUNGARIAN) (3000K) (Note)
*910 4-469-856-81 αHandbook (SLOVAK) (3000K) (Note)
*910 4-469-856-91 αHandbook (SWEDISH) (3000K) (Note)
*910 4-469-857-11 αHandbook (FINNISH) (3000K) (Note)
*910 4-469-857-21 αHandbook (NORWEGIAN) (3000K) (Note)
*910 4-469-857-31 αHandbook (DANISH) (3000K) (Note)
*910 4-469-857-41 αHandbook (THAI) (3000K) (Note)
*910 4-469-857-51 αHandbook (UKRAINIAN) (3000K) (Note)
*910 4-536-699-11 αHandbook (ENGLISH) (3500J) (Note)
*910 4-536-699-21 αHandbook (FRENCH) (3500J) (Note)
*910 4-536-699-31 αHandbook (SPANISH) (3500J) (Note)
*910 4-536-699-41 αHandbook (PORTUGUESE) (3500J) (Note)
*910 4-536-699-51 αHandbook (TRADITIONAL CHINESE) (3500J) (Note)
*910 4-536-699-61 αHandbook (SIMPLIFIED CHINESE) (3500J) (Note)
*910 4-536-699-71 αHandbook (RUSSIAN) (3500J) (Note)
*910 4-536-699-81 αHandbook (ARABIC) (3500J) (Note)
*910 4-536-699-91 αHandbook (PERSIAN) (3500J) (Note)
*910 4-536-700-11 αHandbook (THAI) (3500J) (Note)
*910 4-536-700-21 αHandbook (UKRAINIAN) (3500J) (Note)
This unit has no bundled CD-ROM.
Contents included in the CD-ROM will be supplied to customers as
follows.
• αHandbook (PDF)
- You can access the URL of the support site described in the
Instruction Manual.
- All of the contents in the αHandbook (PDF) are included in the
Instruction Manual or built-in guide.
• Application Software
- If a customer requests the CD-ROM, consult with each Head
Quarters.
Ref. No. Part No. Description
8-328-301-31 Rechargeable battery pack NP-FW50/UC (US, CND)
8-328-301-51 Rechargeable battery pack NP-FW50/CE (EXCEPT US,
CND, RU, CH)
Ref. No. Part No. Description
8-328-301-55 Rechargeable battery pack NP-FW50/RU (RU)
8-328-301-72 Rechargeable battery pack NP-FW50/CN (CH)
2-2. SELECTION PARTS
Ref. No.153
Select the optimum thickness of washer.
Part No. Description
*4-185-995-01 IM WASHER (A), ADJUST (t = 0.05)
*4-185-995-11 IM WASHER (A), ADJUST (t = 0.1)
*4-185-995-21 IM WASHER (A), ADJUST (t = 0.15)
*4-185-995-31 IM WASHER (A), ADJUST (t = 0.2)
*4-185-995-41 IM WASHER (A), ADJUST (t = 0.25)
*4-185-995-51 IM WASHER (A), ADJUST (t = 0.3)
*4-185-995-61 IM WASHER (A), ADJUST (t = 0.35)
*4-185-995-71 IM WASHER (A), ADJUST (t = 0.4)
*4-185-995-81 IM WASHER (A), ADJUST (t = 0.45)
*4-185-995-91 IM WASHER (A), ADJUST (t = 0.495)
Ref. No.154
Select the optimum thickness of washer.
Part No. Description
*4-185-998-01 IM WASHER (B), ADJUST (t = 0.05)
*4-185-998-11 IM WASHER (B), ADJUST (t = 0.1)
*4-185-998-21 IM WASHER (B), ADJUST (t = 0.15)
*4-185-998-31 IM WASHER (B), ADJUST (t = 0.2)
*4-185-998-41 IM WASHER (B), ADJUST (t = 0.25)
*4-185-998-51 IM WASHER (B), ADJUST (t = 0.3)
*4-185-998-61 IM WASHER (B), ADJUST (t = 0.35)
*4-185-998-71 IM WASHER (B), ADJUST (t = 0.4)
*4-185-998-81 IM WASHER (B), ADJUST (t = 0.45)
*4-185-998-91 IM WASHER (B), ADJUST (t = 0.495)
Ref. No.155
Select the optimum thickness of washer.
Part No. Description
*4-185-999-01 IM WASHER (C), ADJUST (t = 0.05)
*4-185-999-11 IM WASHER (C), ADJUST (t = 0.1)
*4-185-999-21 IM WASHER (C), ADJUST (t = 0.15)
*4-185-999-31 IM WASHER (C), ADJUST (t = 0.2)
*4-185-999-41 IM WASHER (C), ADJUST (t = 0.25)
*4-185-999-51 IM WASHER (C), ADJUST (t = 0.3)
*4-185-999-61 IM WASHER (C), ADJUST (t = 0.35)
*4-185-999-71 IM WASHER (C), ADJUST (t = 0.4)
*4-185-999-81 IM WASHER (C), ADJUST (t = 0.45)
*4-185-999-91 IM WASHER (C), ADJUST (t = 0.495)
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.2 2014.04

ILCE-3000K/3500J_L2
3-1
3. ASSEMBLY
Assembly-1: Notes on Assembling the ST Block
Pass the harnesses to these claws.
Harness (SK-1001) (Pink)
Harness (SK-1003) (Orange)
Harness (SK-1002) (White)
Assembly-2: Notes on Assembling the RL Block
A
djust these positions.
Adjust this position.
RL-1023 Flexible Board
3-1. ASSEMBLY
Assembly-3: Screw tightening sequence when assem-
bling the Radiation Plate (IM)
2
1
3
3
Radiation Plate (IM)
Assembly-4: IM Adjust Washer (A, B, C) putting position
MB N Frame Assy
Assembly-5: Screw tightening sequence when assem-
bling the MB Charge Unit
12
12
3
MB Charge Unit
Assembly-6: Apply grease on the MB N Plate SP
MB N Plate SP
GG-85
(J-6082-626-A)
Assembly-7: Notes on Assembling the Sheet (WS) (771)
A portion
B portion
Sheet (WS) (771)
Sheet (WS) (771)
Adhesive part
(Back side)
Adhesive part
Insert the A portion.
Insert the B portion.
Gap
Space
Front Plate
Attach the Sheet (WS) (771) as shown in the figure.

ILCE-3000K/3500J_L2
3-2
Assembly-8: Notes on Assembling the Sheet (SY) (771)
A portion
Sheet (SY) (771)
Attach the Sheet (SY) (771) as shown in the figure.
Sheet (SY) (771)
Claw
Connector
Insert the A portion of the
Sheet (SY) (771) to this space.
Do not press this IC.
Attach the adhesive part
on this part.
Attach the adhesive
part on this part.

ILCE-3000K/3500J_L2
3-3E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
*Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to the service manual, check if there is dirt on the OLPF.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1Souse the one cleaning cloth in ethyl alcohol.
2Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 15 or 6 times.
*Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 25 or 6 times.
*Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
1Souse the cleaning
cloth in ethyl alcohol.
2The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310

LEVEL 2
ILCE-3000K_L2 Sony Corporation
SUPPLEMENT-1
File this supplement with the service manual.
• Revision of EXPLODED VIEWS.
• Addition of ASSEMBLY.
(13-086)
SERVICE MANUAL
Ver. 1.1 2013.09
2013I08-1
© 2013.09
Published by Sony Techno Create Corporation
Addition of ASSEMBLY
Change of ST Assy (771) and addition of Assembly
In this Supplement-1, change of the ST Assy (771) and the corresponding processing are added to the Assembly
for guidance.
In addition, change of arrangement of the ST harness is also added to the Assembly for guidance.
2. REPAIR PARTS LIST
2-1. EXPLODED VIEWS
2-1-3. ST SECTION -: Points changed portion
&: Points added portion
Page Former New
2-5
ns: not supplied




#
12
Bosses
#12
#12
ns
#12
A
2105
110
1,2-1,2-2,
2-3
112
(Orange)
111
(Pink)
113
(White)
107
108
MIC901
C901
ns: not supplied




#
12
Bosses
#12
#12
ns
#12
A
(Note 3)
2105
110
1,2-1,2-2,
2-3
112
(Orange)
111
(Pink)
113
(White)
107
108
MIC901
C901
Ref. No. Part No. Description
105 X-2587-853-1 ST ASSY (771)
Ref. No. Part No. Description
105 X-2587-853-2 ST ASSY (771) (Note 3) =
_
US Model
Canadian Model
AEP Model
UK Model
Russian Model
E Model
Australian Model
Chinese Model
Korea Model
Brazilian Model
Tourist Model
9-834-741-81
ILCE-3000K
Note 3: Refer to “Assembly-9: Notes on Assembling the
ST ASSY” when assembling.

ILCE-3000K_L2
– 2 –
3. ASSEMBLY
3-1. ASSEMBLY -: Points changed portion
Page Former New
3-1
Pass the harnesses to these claws.
Harness (SK-1001) (Pink)
Harness (SK-1003) (Orange)
Harness (SK-1002) (White)
Pass the harnesses to these claws.
Form the harnesses as shown below
with tweezers or the like.
Harness (SK-1001) (Pink)
Harness (SK-1003) (Orange)
Harness (SK-1002) (White)

ILCE-3000K_L2
– 3 –
&: Points added portion
Page Former New
3-2
Assembly-9: Notes on Assembling the ST ASSY
Cover ST (771)
Rib A
Rib A
NG
OK
Rib B
Suffix-1 and suffix-2 of part number exist in the ST Assy
(771).
Check whether the Rib A of the Cover ST (771) contained
in the part of part number suffix-1 is cut.
If the Rib A is not cut, cut it as shown below.
Insert a nipper in the direction of arrow and cut
the Rib A of the Cover ST (771). (Rib B need not be cut.)
Confirm that cut surface of the Rib A does not protrude
out of portion A.
After that, draw a circle with a permanent marker as below.
Size and color are arbitrary.
Nipper
Cut surface of the Rib A
Portion A
Circle
&: Points added portion
Page Former New
3-2
Cushion (ST) (771)
ST Assy (771)
Cushion (ST)(771) is stuck to the part of part number suffix-1
of the ST Assy (771).
Remove the cushion (ST)(771) so that no adhesive remains.
This work is not necessary for the part of part number suffix-2
of the ST Assy (771).
After that, draw a circle with a permanent marker as below.
Size and color are arbitrary.
Circle