Sony Dvp-ns400d User manual

SERVICE MANUAL

US Model

Canadian Model

AEP Model

UK Model

E Model

Brazil Model

Argentina Model

Mexico Model

CD/DVD PLAYER

DVP-NS400D

RMT-D128A/D128P

SPECIFICATIONS

•Audio/video cord (pinplug ×3 ypinplug ×3) (1)

•Remote commander (remote) RMT-D128A (1) (US, CND, E, MX, AR, BR)

RMT-D128P (1) (AEP, UK)

•Size AA

•Abbreviation

AR : Argentina

BR : Brazilian

CND : Canadian

MX : Mexican

(R6) batteries (2)

System

Laser Semiconductor laser

Signal format system NT

PAL (AEP, UK)

Audio characteristics

Frequency response DVD (PCM 96 kHz): 2 Hz to 44 kHz (±1.0 dB)

DVD (PCM 48 kHz): 2 Hz to 22 kHz (±0.5 dB)

CD: 2 Hz to 20 kHz (±0.5 dB)

Signal-to-noise ratio (S/N ratio) 115 dB (LINE OUT L/R (AUDIO) jacks only)

Harmonic distortion 0.003 %

Dynamic range DVD: 103 dB

CD: 99 dB

Wow and flutter Less than detected value (±0.001% W PEAK)

Outputs

Jack name Jack type Maximum output level Load impedance

LINE OUT L/R (AUDIO) Phono jack 2 Vrms (at 50 kilohms) Over 10 kilohms

DIGITAL OUT (OPTICAL) Optical output jack -18 dBm Wave length: 660 nm

DIGITAL OUT (COAXIAL) Phono jack 0.5 V

P-P

75 ohms terminated

LINE OUT (VIDEO) Phono jack 1.0 V

P-P

75 ohms, sync negative

SVIDEO OUT 4-pin mini DIN Luminance signal: 1.0 V

P-P

Color signal:

0.3 (PAL)

(NTSC)

.286 V

P-P

75 ohms, sync negative

75 ohms terminated

COMPONENT

VIDE

(US, CND, E, MX, AR, BR)

O OUT(Y, P

, P

)Phono jack Y: 1.0 V

P-P

, P

: 0.7 V

P-P

75 ohms, sync negative

75 ohms

5.1CH OUTPUT Phono jack 2 Vrms (at 50 kilohms) Over 10 kilohms

General

Power requirements 120VAC, 60 Hz (US, CND, MX)

110 to 240 V AC, 50/60 Hz (E, BR)

220 to 240 V AC, 50/60 Hz (AEP, UK,AR)

Power consumption 13 W (US, CND, E, MX, AR, BR)

14 W (AEP, UK)

Dimensions (approx.) 430 ×74 ×256 mm (17 ×3 ×10

in.) (w/h/d) incl. projecting parts

Mass (approx.) 2.7 kg (5lb)

Operating temperature 5 °C to 35 °C (41 °F to 95 °F)

Operating humidity 25 % to 80 %

Supplied accessories

Specifications and design are subject to change without notice.

Photo: Black type

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 2 –

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER

EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS

NECESSARY TO CONFIRM LASER BEAM EMISSION,

BE SURE TO OBSERVE FROM A DISTANCE OF

MORE THAN 25 cm FROM THE SURFACE OF THE

OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous ra-

diation exposure.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0

SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE

DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ

DE FONCTIONNEMENT. NE REMPLACER CES COM-

POSANTS QUE PAR DES PIÈCES SONY DONT LES

NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED

LINE WITH MARK 0ON THE SCHEMATIC DIAGRAMS

AND IN THE PARTS LIST ARE CRITICAL TO SAFE

OPERATION. REPLACE THESE COMPONENTS WITH

SONY PARTS WHOSE PART NUMBERS APPEAR AS

SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-

LISHED BY SONY.

CAUTION:

The use of optical instrument with this product will increase eye

hazard.

Fig. A. Using an AC voltmeter to check AC leakage.

1.5 k

Ω

0.15 µF

voltmeter

(0.75 V)

To Exposed Metal

Parts on Set

Earth Ground

LEAKAGE TEST

The AC leakage from any exposed metal part to earth ground

and from all exposed metal parts to any exposed metal part having

a return to chassis, must not exceed 0.5 mA (500 microamperes).

Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers' instructions to use these

instruments.

2. A battery-operatedAC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indica-

tion is 0.75V, so analog meters must have an accurate low-

voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-

amples of a passive VOM that is suitable. Nearly all battery

operated digital multimeters that have a 2VAC range are suit-

able. (See Fig. A)

1. Check the area of your repair for unsoldered or poorly-sol-

dered connections. Check the entire board surface for solder

splashes and bridges.

2. Check the interboard wiring to ensure that no wires are

“pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transis-

tors, that were installed during a previous repair. Point them

out to the customer and recommend their replacement.

4. Look for parts which, though functioning, show obvious signs

of deterioration. Point them out to the customer and recom-

mend their replacement.

5. Check the line cord for cracks and abrasion. Recommend the

replacement of any such line cord to the customer.

6. Check the B+ voltage to see it is at the values specified.

7. Check the antenna terminals, metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC leakage.

Check leakage as described below.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer:

CLASS 3B LASER

LUOKAN 3B LASER

LASERKLASS 3B

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 3 –

TABLE OF CONTENTS

Section Title Page Section Title Page

Service Note ............................................................................ 4

1. GENERAL

Getting Started .............................................................. 1-3

Hookups ........................................................................ 1-3

Playing Discs ................................................................. 1-7

Searching for a Scene................................................... 1-9

Viewing Information About the Disc.............................. 1-10

Sound Adjustments ....................................................... 1-11

Enjoying Movies ............................................................ 1-13

Using Various Additional Functions .............................. 1-14

Settings and Adjustments ............................................. 1-15

Additional Information ................................................... 1-18

2. DISASSEMBLY

2-1. Case Removal ............................................................... 2-1

2-2. MB-98 Board Removal .................................................. 2-1

2-3. Rear Panel Removal (Except AEP, UK)........................ 2-1

2-4. Rear Panel, ER-15 Board Removal (AEP, UK)............. 2-1

2-5. Tray Cover Removal ...................................................... 2-2

2-6. Front Panel Removal ..................................................... 2-2

2-7. Power Block Removal ................................................... 2-2

2-8. Mechanism Deck Removal............................................ 2-2

2-9. AI-23 Board Removal .................................................... 2-3

2-10. Tray Removal ................................................................. 2-3

2-11. Loading Motor (M001), MS-81 Board Removal............ 2-3

2-12. Optical Pick-up Removal ............................................... 2-3

2-13. Internal Views ................................................................ 2-4

2-14. Circuit Boards Location ................................................. 2-5

3. BLOCK DIAGRAMS

3-1. Overall Block Diagram................................................... 3-1

3-2. RF/Servo Block Diagram............................................... 3-3

3-3. Signal Processor Block Diagram .................................. 3-5

3-4. System Control Block Diagram ..................................... 3-7

3-5. Video Block Diagram..................................................... 3-9

3-6. Audio Block Diagram ..................................................... 3-11

3-7. Interface Control Block Diagram ................................... 3-13

3-8. Power 1 Block Diagram ................................................. 3-15

3-9. Power 2 Block Diagram ................................................. 3-17

3-10. Power 3 Block Diagram ................................................. 3-19

4. PRINTED WIRING BOARDS AND SCHEMATIC

DIAGRAMS

4-1. Frame Schematic Diagram............................................ 4-3

4-2. Printed Wiring Boards and Schematic Diagrams ......... 4-5

MS-81 (LOADING) Printed Wiring Board and

Schematic Diagram ....................................................... 4-5

MB-98 Printed Wiring Board ......................................... 4-7

MB-98 (RF AMP, SERVO) Schematic Diagram ............ 4-11

MB-98 (ARP, SERVO DSP) Schematic Diagram.......... 4-13

MB-98 (AV DECODER) Schematic Diagram................ 4-15

MB-98 (BNR) Schematic Diagram ................................ 4-17

MB-98 (DRIVE) Schematic Diagram ............................ 4-19

MB-98 (SYSTEM CONTROL)

Schematic Diagram ....................................................... 4-21

MB-98 (CLOCK GENERATOR)

Schematic Diagram ....................................................... 4-23

MB-98 (AUDIO DSP) Schematic Diagram.................... 4-25

MB-98 (D/A CONVERTER) Schematic Diagram.......... 4-27

AI-23 Printed Wiring Board ........................................... 4-29

AI-23 (VIDEO BUFFER) Schematic Diagram............... 4-31

AI-23 (AUDIO AMP) Schematic Diagram ..................... 4-33

AI-23 (5.1CH AUDIO AMP) Schematic Diagram .......... 4-35

AI-23 (IF CON) Schematic Diagram ............................. 4-37

ER-15 Printed Wiring Board (AEP, UK) ........................ 4-39

ER-15 (EURO AV) Schematic Diagram (AEP, UK)....... 4-41

HS13S0E Printed Wiring Board (AEP, UK, AR) ........... 4-43

HS13S0E Schematic Diagram (AEP, UK, AR) ............. 4-45

HS13S0F Printed Wiring Board (E, BR) ....................... 4-47

HS13S0F Schematic Diagram (E, BR) ......................... 4-49

HS13S0U Printed Wiring Board (US, CND, MX) .......... 4-51

HS13S0U Schematic Diagram (US, CND, MX) ............ 4-53

TOP-244U Printed Wiring Board (US, CND) ................ 4-55

TOP-244U Schematic Diagram (US, CND) .................. 4-57

5. IC PIN FUNCTION DESCRIPTION

5-1. System Control Pin Function

(MB-98 Board IC103) .................................................... 5-1

6. TEST MODE

6-1. General Description ...................................................... 6-1

6-2. Starting Test Mode ........................................................ 6-1

6-3. Syscon Diagnosis.......................................................... 6-1

6-4. Drive Auto Adjustment .................................................. 6-5

6-5. Drive Manual Operation ................................................ 6-7

6-6. Mecha Aging ................................................................. 6-10

6-7. Emergency History........................................................ 6-10

6-8. Version Information ....................................................... 6-11

6-9. Video Level Adjustment ................................................ 6-11

6-10. IF Con Self Diagnostic Function ................................... 6-11

6-11. Troubleshooting ............................................................. 6-18

7. ELECTRICAL ADJUSTMENT

7-1. Power Supply Check ..................................................... 7-1

1. HS13S0E/HS13S0F/HS13S0U/TOP-244U Boards...... 7-1

7-2. Adjustment of Video System ......................................... 7-2

1. Video Level Adjustment ................................................ 7-2

2. Checking S Video Output S-Y....................................... 7-2

3. Checking S Video Output S-C....................................... 7-2

4. Checking Component Video Output Y .......................... 7-2

5. Checking Component Video Output B-Y ...................... 7-3

6. Checking Component Video Output R-Y ...................... 7-3

7. Checking RGB Output R ............................................... 7-3

8. Checking RGB Output G............................................... 7-3

9. Checking RGB Output B ............................................... 7-4

7-3. Adjustment Related Parts Arrangement ....................... 7-6

8. REPAIR PARTS LIST

8-1. Exploded Views ............................................................. 8-1

8-1-1. Case Assembly ........................................................ 8-1

8-1-2. Chassis Assembly .................................................... 8-3

8-1-3. Mechanism Deck Assembly ..................................... 8-5

8-2. Electrical Parts List ....................................................... 8-6

• Abbreviation

AR : Argentina

BR :Brazilian

CND : Canadian

MX :Mexican

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 4 –

SERVICE NOTE

1. DISASSEMBLY

• This set can be disassembled in the order shown below.

Set

Case

(Page 2-1)

Tray Cover

(Page 2-2)

Front Panel

(Page 2-2)

MB-98 Board

(Page 2-1)

ER-15 Board

(AEP, UK)

(Page 2-1)

Tray

(Page 2-3)

Loading Motor (M001),

MS-81 Board

(Page 2-3)

Opticl Pick-up

(Page 2-3) AI-23 Board

(Page 2-3)

Power Block

(Page 2-2)

Mechanism Deck

(Page 2-2)

Rear Panel

(Page 2-1)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 5 –

1) Remove the case from the set. (Refer to 2-1)

2) Remove the MB-98 board. (Refer to 2-1)

3) Set the stand (with CK-106 board) as shown in Fig. 2.

Fig. 2

4) Set the Jig A board as shown in Fig. 3.

Fig. 3

2. DISC REMOVAL PROCEDURE

(at POWER OFF)

1) Insert a tapering driver into the aperture of the unit bottom,

and move the lever of chuck cam in the direction of the arrow

A. (See Fig. 1)

2) Draw out the tray in the direction of the arrow B, and remove

a disc. (See Fig. 1)

Fig. 1

3. HOW TO SERVICE MB-98 BOARD

• Jig (J-6090-107-A) Extension cable

Tray

Lever of chuck cam

Aperture

CK-105 board

Stand

(with CK-106 Board)

Nine flexible flat cables

FFC 5P (EXCEPT DVP-NC600), FFC 9P,

FFC 15P, FFC26P,

FFC 9P (DVP-NS500P/NS700P),

FFC 15P (DVP-NS400D),

FFC 25P (EXCEPT DVP-NS300 J model),

FFC 29P (DVP-NS300 J model)

1MB-98 board

2Stand

(with CK-106 board)

3Connector (CN101)

4Two screws (B3)

4Connector (CN109)

1CK-105 board

3Claw

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 6 –

5) Set the four flexible flat cables as shown in Fig. 4.

Fig. 4

6) Set the MB-98 board as shown in Fig. 5, Fig.6.

Fig. 5

Fig. 6

4Connector (FFC15P: CN110)

2Flexible flat cables

(FFC15P: CN201)

3Three connectors

(FFC26P: CN102/

FFC9P: CN104/

FFC5P: CN106)

1Three flexible flat cables

(FFC26P: CN201/

FFC9P: CN202/

FFC5P: CN402)

1Connector

(FFC25P: CN203)

3Connector

(FFC15P: CN301)

2Flexible flat cable

(FFC25P: CN801)

4Flexible flat cable

(FFC15P: CN802)

MB-98 board

4. HOWTO DISCRIMINATE MODELTYPES IN

AEP MODEL

1) Start up the test mode, display “Test Mode Menu” as shown

below on the monitor, and confirm the model name.

2) Confirm the model type with the menu “2-4 Model Type” in

the test mode, then discriminate the model with referring the

table shown below.

(Refer to page 6-2 to confirm “2-4 Model Type”)

Model Type Model Display

AEP (DPX1411BM) 1 3 DPX-1411CE

AEP (DPX1411HM) 1 3 DPX-1411CE

AEP (DPX1412BM) 1 4 DPX-1412CE

AEP (DPX1412HM) 1 4 DPX-1412CE

•Description about model name

DPX14xxBM Color of set

B : Black

H : Titanium gray

Model Display

Test Mode Menu

0. Syscon Diagnosis

1. Drive Auto Adjustment

2. Drive Manual Operation

3. Mecha Aging

4. Emergency History

5. Version Information

6. Video Level Adjustment

Exit: POWER Key

Model : DPX-14xxxx

Revision : 1.xxxx Last Off: xx

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 7 –

5. CONNECTION OF SERVICE JIG

CK-105

Mechanism deck

AI-23

MB-98

AI-23

CK-106

(Stand)

B to B Connector 15P

FFC26P

(Used the set)

FFC 9P

(Used the set)

FFC 5P

(Used the set)

FFC26P

FFC 9P

FFC 5P

FFC15P

FFC15P FFC25P

CN101 CN102

CN103 CN104

CN105 CN106

CN201

CN202

CN402

CN109CN403 CN110 CN201

CN202

CN101

CN801

CN203

CN802

CN301

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-1

SECTION 1

GENERAL This section is extracted from instruction

manual (3-067-120-11).

DVP-NS400D

About this Manual

•Instructions in this manual describe the

controls on the remote. Yo ucan also use the

controls on the player if they have the same

or similar names as those on the remote.

•The meaning of the icons used in this

manual is described below:

This Player Can Play the

Following Discs

The “DVD VIDEO” logo is a trademark.

Your player has a region code printed on the

back of the unit and will only play DVDs

labeled with identical region codes.

DVDs labeled will also play on this

player.

If you try to play any other DVD, the

message “Playback prohibited by area

limitations.” will appear on the TV screen.

Depending on the DVD, no region code

indication may be labeled even though

playing the DVD is prohibited by area

restrictions.

The player cannot play the following discs:

•CD-ROMs (PHOTO CDs included)

•All CD-Rs other than music and VCD

format CD-Rs

•Data part of CD-Extras

•DVD-ROMs

•DVD Audio discs

•HD layer on SACDs

Also, the player cannot play the following

discs:

•A DVD with a different region code (page

79).

•A disc recorded in a color system other than

NTSC, such as PAL or SECAM (This

player conforms to the NTSC color

system).

•A disc that has a non-standard shape (e.g.,

card, heart)

•A disc with paper or stickers on it.

•A disc that has the adhesive of cellophane

tape or a sticker still left on it.

Icon Meaning Icon Meaning

Functions

available in

DVD video

mode

Functions

available in

music CD

mode

Functions

available in

VIDEO CD

mode

convenient

features

Format of discs

DVD VIDEO

VIDEO CD

Music CD

Region code

Example of discs that the player

cannot play

ALL

MODEL NO.

DVP–XXXX

CD/DVD PLAYER

AC 00V 00Hz

00W

NO.

SONY CORPORATION

MADE IN JAPAN 0-000-000-00

Region code

Note

Some CD-Rs or CD-RWs cannot be played on this

player depending upon the recording quality or

physical condition of the disc, or the characteristics of

the recording device.

Furthermore, the disc will not play if it has not been

correctly finalized. For more information, see the

operating instructions for the recording device.

Some playback operations of DVDs and

VIDEO CDs may be intentionally set by

software producers. Since this player plays

DVDs and VIDEO CDs according to the disc

contents the software producers designed,

some playback features may not be available.

Also, refer to the instructions supplied with

the DVDs or VIDEO CDs.

This product incorporates copyright

protection technology that is protected by

method claims of certain U.S. patents, other

intellectual property rights owned by

Macrovision Corporation, and other rights

owners. Use of this copyright protection

technology must be authorized by

Macrovision Corporation, and is intended for

home and other limited viewing uses only

unless otherwise authorized by Macrovision

Corporation. Reverse engineering or

disassembly is prohibited.

Notes about the Discs

On handling discs

•To keep the disc clean, handle the disc by its

edge. Do not touch the surface.

•Do not expose the disc to direct sunlight or

heat sources such as hot air ducts, or leave

it in a car parked in direct sunlight as the

temperature may rise considerably inside

the car.

•After playing, store the disc in its case.

On cleaning

•Before playing, clean the disc with a

cleaning cloth.

Wipe the disc from the centre out.

•Do not use solvents such as benzine,

thinner, commerciallyavailablecleaners,or

anti-static spray intended for vinyl LPs.

Note on playback operations of

DVDs and VIDEO CDs.

Copyrights

Index to Parts and Controls

For more information, refer to the pages indicated in parentheses.

APOWER switch/indicator (30)

2DOLBY DIGITAL indicator

Lights up when:

- playing back a Dolby Digital

soundtrack on the DVD

- the disc is not inserted

3BNR (Block Noise Reduction) button/

indicator (56)

4SURROUND button/indicator (50)

5Disc tray (30)

6A(open/close) button (30)

7./>(previous/next) buttons (31)

8C/X/x/c/ ENTER buttons (25)

9TITLE button (33)

q; DVD MENU button (33)

qa ORETURN button (34)

qs DISPLAY button (12)

qd x(stop) button (30)

qf X(pause) button (31, 62)

qg H(play) button (30)

qh Front panel display (9)

qj (remote sensor) (14)

Front Panel

When playing back a DVD

When playing back a VIDEO CD (PBC)

When playing back a CD or VIDEO CD (without PBC)

Front Panel Display

DVD

PGM SHUFFLE TITLE CHAP HOUR MIN SEC

DTS ANGLE REPEAT1

A-B

Digital

Playing time (44)

Disc type Playing

status

Current chapter (44)

Current audio

signal (49)

Lights up when you can change

the angle (54)

Currentplay

mode (35) Current title (44)

VIDEOCD

PBC

MIN SEC

A-B

Playing

status

Current play mode

(35)

Disc type

Current scene (44) Playing time (44)

Lights up when playing back a VIDEO CD with PBC (34)

VIDEOCD

PGM SHUFFLE TRACK INDEX MIN SEC

REPEAT1

A-B

Playing time (44)

Disc type

Playing

status

Current track and

index (44)

Current play mode (35)

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-2

1DIGITAL OUT (COAXIAL) jack (21,

23, 24)

2DIGITAL OUT (OPTICAL) jack (21,

23, 24)

3LINE OUT L/R (AUDIO) 1/2 jacks (15,

20, 23, 24)

4LINE OUT (VIDEO) 1/2 jacks (17)

5S VIDEO OUT 1/2 jacks (17)

6COMPONENT VIDEO OUT jacks (17)

75.1CH OUTPUT jacks (21)

Rear Panel

LINE OUT

PCM/DTS/

DOLBY DIGITAL

S VIDEO

OUT

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

R-AUDIO 1-L VIDEO 1

R-AUDIO 2-L VIDEO 2

DIGITAL OUT

5.1CH OUTPUT

WOOFER

FRONT REAR CENTER

OPEN/CLOSE button (31)

BNumber buttons

CCLEAR button (35)

DANGLE button (54)

5AUDIO button (48)

6PROGRAM button (35)

7SHUFFLE button (37)

H./>PREV/NEXT buttons (31)

Ic/C SEARCH/STEP buttons

(40)

JHPLAY button (30)

KTITLE button (33)

LDISPLAY button (35)

MTV [/1(on/standby) button (63)

N[/1(on/standby) button (30)

OBNR (Block Noise Reduction) button

(56)

PTV/VIDEO button (63)

QVOL +/–buttons (63)

RENTER button

SSUBTITLE button (55)

TTIME/TEXT button (44)

UREPEAT button (37)

VINSTANT REPLAY button (31)

WSURROUND button (50)

X/ySCAN/SLOW buttons (40)

YXPAUSE button (31)

ZxSTOP button (30)

wj DVD MENU button (33)

wk C/X/x/cbuttons (25)

wl ENTER button

e; ORETURN button (34)

Remote

123

456

Guide to Control Menu Display

Use the Control Menu to select a function that you’d like to use. The Control Menu display

appears when the DISPLAY button is pressed. For details, please refer to the page in

parenthesizes.

List of Control Menu Items

Control Menu

OFF

1: ENGLISH

2: FRENCH

3: SPANISH

OFF

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

Select: Cancel:

SUBTITLE

ENTER RETURN

PLAY

Current playing chapter

number (Video CD/CD:

index number)

Playing time

Total number of chapters or indexes recorded

Current playing title number

(Video CD/CD: track number)

Options

Current setting

Total number of titles or tracks recorded

Playback status

(N Playback, XPause, xStop, etc.)

Functionnameofselected

Control Menu item

Operation message

Icon of selected

Control Menu item

Control Menu items

Type of disc being

played back

TITLE (DVD only) (page 41)/

SCENE (only VIDEO CD in PBC

playback) (page 41)/TRACK (VIDEO CD

only) (page 41)

Selects the title (DVD), the scene (VIDEO CD

in PBC playback) or the track (VIDEO CD) to

be played.

CHAPTER (DVD only) (page

41)/INDEX (VIDEO CD only) (page 41) Selects the chapter (DVD) or the index

(VIDEO CD) to be played.

TRACK (CD only) (page 41) Selects the track (CD) to be played.

INDEX (CD only) (page 41) Selects the index (CD) to be played.

TIME/TEXT (page 44) Check the elapsed time and the remaining

playback time.

Input the time code for picture and music

searching.

Displays the DVD or the CD text.

AUDIO (page 48) Changes the audio setting.

SUBTITLE (DVD only) (page

55) Displays the subtitles.

Changes the subtitle language.

ANGLE (DVD only) (page 54) Changes the angle.

zEach time you press DISPLAY, the Control Menu display changes as follows:

You can display the Control Menu display 1 only during CD playback. The Control Menu items are different

depending on the disc.

zThe Control Menu icon indicator lights up in green when you select any item except

“OFF.”(“SURROUND,”“PROGRAM,”“SHUFFLE,”“REPEAT,”“A-B Repeat,”“DIGITAL VIDEO

ENHANCER”only). The “ANGLE”indicator lights up in green only when the angles can be changed.

SURROUND (page 50) Selects the surround functions.

ADVANCED (DVD only) (page

47) Checkstheinformation (bit rateorlayer) on the

disc while playing a DVD.

CUSTOM PARENTAL

CONTROL (page 58) Sets the disc to prohibit playing.

SETUP (page 65) QUICK Setup (page 25)

Use Quick Setup to choose the desired

language of the on screen display, the shape of

the TV screen, the audio output, and speakers

connected to the player.

CUSTOM Setup

In addition to the Quick Setup setting, you can

adjust the image and sound quality, Parental

Control, and other various settings.

RESET

Returns the settings in “SETUP”to the default

setting.

PROGRAM (page 35) Selects the title, the chapter or the track to play

a disc in the order you want.

SHUFFLE (page 37) Plays the title, the chapter or the track in

random order.

REPEAT (page 37) Plays the entire disc (all titles/all tracks)

repeatedly or one title/chapter/track repeatedly.

A-B REPEAT (page 38) Specifies the parts you want to play repeatedly.

BNR (page 56) Adjusts the picture quality by reducing the

“block noise”or mosaic like patterns that

appear on your TV screen.

DIGITAL VIDEO ENHANCER

(page 57) Exaggeratesthe outlineof theimagetoproduce

a sharper picture.

VIEWER (DVD/VIDEO CD only)

(page 42) Divides the screen into 9 sub-screens to help

you find the scene you want quickly.

Control Menu display 1

Control Menu display 2

(The items except the first three items from the top are changed to other items.)

ADVA NCED display (Appears if you select any setting other than "OFF." See page 47.)

Control Menu display off

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-3

Getting Started

Quick Overview

A quick overview presented in this chapter will give you enough information to start using the

player for your enjoyment. To use the surround sound features of this player, refer to “Hookups”

on page 17.

Note

You cannot connect this player to a TV that does not have a video input jack.

Be sure to turn off the power of each component before connecting.

Step 1: Unpacking

Check that you have the following items:

•Audio/video cord (pinplug ×3 ypinplug ×3) (1)

•Remote commander (remote) RMT-D128A (1)

•Size AA (R6) batteries (2)

Step 2: Inserting Batteries into the Remote

You can control the player using the supplied remote. Insert two size AA (R6) batteries by

matching the 3and #ends on the batteries to the markings inside the compartment. When using

the remote, point it at the remote sensor on the player.

Notes

•Do not leave the remote in an extremely hot or humid place.

•Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

•Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so may cause a

malfunction.

•If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from

battery leakage and corrosion.

Getting Started

Step 3: TV Hookups

Connect the supplied audio/video cord and power cord in the order (1~3) shown below. Be

sure to connect the power cord last.

When connecting to a wide screen TV

Depending on the disc, the image may not fit your TV screen.

If you want to change the aspect ratio, please refer to page 67.

PCM/DTS/

DOLBY DIGITAL

S VIDEO

OUT

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

R-AUDIO 1-L VIDEO 1

R-AUDIO 2-L VIDEO 2

DIGITAL OUT LINE OUT

5.1CH OUTPUT

WOOFER

FRONT REAR CENTER

R-AUDIO 1-L VIDEO 1

R-AUDIO 2-L VIDEO 2

LINE OUT

VIDEO

AUDIO

INPUT

(yellow)

(white)

(red)

Power source

CD/DVD Player

Power source

l: Signal flow

to video input

to LINE OUT

L/R (AUDIO) 1

Audio/video

cord (supplied)

to audio input

to LINE OUT (VIDEO) 1

Step 4: Playing a Disc

1Turn on the TV.

2Switch the input selector on the TV to the player.

3Press POWER on the player.

4Press Aon the player to open the disc tray.

5Place the disc on the tray with the playback side facing down.

6Press H.

The disc tray closes and the player begins playing the disc.

After Step 6

Depending on the disc, amenu maybe displayed on the TV screen. If so, select the item you want

from the menu and play the DVD (page 33) or VIDEO CD disc (page 34).

To stop playing

Press x.

To take out the disc

Press A.

To turn off the player

Press ^/1 on the remote. The player is set to standby mode and the power indicator lights up in

red. Press POWER on the player to turn off completely.

With the playback side facing down

Hookups

Hooking Up the Player

Follow Steps 1 to 4 to hook up and adjust the settings of the player.

Before you start, turn off the power, check that you have all of the supplied accessories, and insert

the batteries into the remote (page 14).

Notes

•

Plug cords securely to prevent unwanted noise.

•

Refer to the instructions supplied with the components to be connected.

Step 1: Connecting the Video Cords

Connect this player to your TV monitor, projector or, AV amplifier (receiver) using a video cord.

Select one of the patterns Athrough C, according to the input jack on your TV monitor,

projector, or AV amplifier (receiver).

INPUT

S VIDEO

PCM/DTS/

DOLBY DIGITAL

S VIDEO

OUT

COMPONENT

VIDEO OUT

COAXIAL

OPTICAL

R-AUDIO 1-L VIDEO 1

R-AUDIO 2-L VIDEO 2

DIGITAL OUT LINE OUT

COMPONENT

VIDEO IN

AUDIO

INPUT

5.1CH OUTPUT

WOOFER

FRONT REAR CENTER

VIDEO

CD/DVD player

TV, projector or AV

amplifier (receiver)

l: Signal flow

Audio/video

cord (supplied)

(yellow)

(yellow) Component video

cord (not supplied)

S VIDEO cord

(not supplied)

TV, projector or AV

amplifier (receiver)

TV, projector or AV

amplifier (receiver)

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Other manuals for DVP-NS400D

This manual suits for next models

Table of contents

Other Sony DVD Player manuals

Popular DVD Player manuals by other brands

Yamaha

Yamaha DVD S540 - Progressive Scan DVD Player Service manual

Yamakawa

Yamakawa DVD-MP12i user manual

Philips

Philips DVP3042/12 user manual

Philips

Philips DVP5900/37B Quick use guide

Roadstar

Roadstar DVD-2020H Service manual

Beko

Beko DVD 2006 user manual

Atak

Atak DVDA2015 instruction manual

LG DV257K owner's manual

auna

auna 10005069 manual

Philips

Philips MCD700/61 user manual

Toshiba

Toshiba SD-2300U owner's manual

LENCO

LENCO DVP-740 X2 user manual

Tevion

Tevion 44330 user guide

Aiwa

Aiwa XD-DV370 operating instructions

Denon

Denon DVM-1805 - DVD Changer operating instructions

Toshiba

Toshiba SD-3815 owner's manual

Sylvania

Sylvania DP170SL8 Service manual

Toshiba

Toshiba SD-P1200 Service manual

Sony DVP-NS400D User manual

Popular DVD Player manuals by other brands