Sony SLV-D950B User manual

3-084-916-E2 (1) GB
DVD Player/
Video Cassette
Recorder
Operating Instructions
SLV-D950B
SLV-D910B
© 2003 Sony Corporation
PAL SECAM

2WARNING
WARNING
To prevent fire or shock
hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to qualified
personnel only.
Mains lead must only be
changed at a qualified
service shop.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the
rear exterior.
CAUTION
The use of optical instruments
with this product will increase
eye hazard. As the laser beam
used in this DVD player/Video
Cassette Recorder is harmful to
eyes, do not attempt to
disassemble the cabinet.
Refer servicing to qualified
personnel only.
Precautions
Safety
• This unit operates on 220 –
240 V AC, 50 Hz. Check
that the unit’s operating
voltage is identical with your
local power supply.
• To prevent fire or shock
hazard, do not place objects
filled with liquids, such as
vases, on the apparatus.
• The unit is not disconnected
from the AC power source
(mains) as long as it is
connected to the wall outlet,
even if the unit itself has been
turned off.
Installing
• Do not install the unit in a
confined space such as a
book or similar unit.
• Do not install the unit in an
inclined position. It is
designed to be operated in a
horizontal position only.
• Keep the unit and discs away
from equipment with strong
magnets, such as microwave
ovens, or large loudspeakers.
• Do not place heavy objects
on the unit.
• Do not place the unit on
surfaces (rugs, blankets, etc.)
or near materials (curtains,
draperies) that may block the
ventilation slots.
Compatible colour
systems
• This VCR is designed to
record using the PAL (B/G)
and SECAM colour systems
and play back using the PAL
(B/G) and SECAM colour
systems. Recording of video
sources based on other colour
systems cannot be
guaranteed.
• Tapes recorded with the
MESECAM colour system
can be played back on this
VCR using a TV or a colour
monitor supporting the
SECAM colour system.
SHOWVIEW is a registered
trademark of Gemstar
Development Corporation. The
SHOWVIEW system is
manufactured under license from
Gemstar Development
Corporation.

3
Welcome!
Welcome!
Thank you for purchasing this
Sony DVD Player/Video
Cassette Recorder. Before
operating this player, please
read this manual thoroughly
and retain it for future
reference.
Caution
For use of the VCR
Televisionprogrammes,films,
video tapes and other
materials may be copyrighted.
Unauthorized recording of
such material may be contrary
to the provisions of the
copyright laws. Also, use of
this recorder with cable
television transmission may
require authorization from the
cable television transmitter
and/or programme owner.
For use of the DVD
player
This product incorporates
copyright protection
technologythat isprotected by
method claims of certain U.S.
patents, other intellectual
property rights owned by
Macrovision Corporation,and
other rights owners. Use of
this copyright protection
technologymust beauthorized
by Macrovision Corporation,
and is intended for home and
other limited viewing uses
only unless otherwise
authorized by Macrovision
Corporation. Reverse
engineering or disassembly is
prohibited.

4Table of contents
Table of contents
2WARNING
3Welcome!
3Caution
6About this manual
6This player can play the following discs
7Notes about discs
Getting Started
8Step 1 : Unpacking
9Step 2 : Setting up the remote commander
11 Step 3 : Connecting the DVD-VCR
13 Step 4 : Setting up the DVD-VCR with the Auto Set Up function
15 Step 5 : Selecting a language
16 Step 6 : Setting the clock
18 Step 7 : Presetting channels
27 Setting the Canal Plus decoder
Basic Operations
31 Playing discs
35 Guide to the on-screen display
37 Playing a tape
40 Recording TV programmes
44 Recording TV programmes using the
ShowView®system (SLV-D950B
only)
48 Recording TV programmes using the
timer
52 Recording TV programmes using
DIAL TIMER (SLV-D950B only)
56 Checking/changing/cancelling timer
settings
Advanced Hookups
59 A/V Receiver hookup
61 S-Video hookup
DVD Settings and
Adjustments
62 Audio Setup
65 Screen Setup
68 Setting the display or sound track
language
70 Parental Control (limiting playback
by children)

5
Table of contents
DVD Additional Operations
73 Using the DVD’s menu
75 Zooming into a scene
76 Changing the angles
77 Displaying the subtitle
78 Various play mode functions
(Programme play, Shuffle play,
Repeat play)
82 Changing the sound
83 Virtual surround setting
85 Playing an MP3 audio track
89 Playing JPEG image files
93 Playing VIDEO CDs with “MENU
OUI/NON” functions
VCR Additional Operations
95 Playing a tape with SQPB function
96 Quick Timer Recording
98 Recording stereo and bilingual
programmes
101 Searching using index function
103 Adjusting the picture (tracking)
105 Changing menu options
107 Editing
Additional Information
110 General setup information
112 Troubleshooting
117 Glossary
119 Specifications
121 Index to parts and controls
126 DVD Audio/Subtitle Language
127 Index

6
About this manual
• The meaning of the icons used in this manual is
described below:
* MP3 (MPEG 1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio data.
This player can play the
following discs
The “DVD VIDEO” logo is a trademark.
Region code
Your player has a region code printed on the
back of the unit and only willplay DVD VIDEO
discs (playback only) labelled with identical
region codes. This system is used to protect
copyrights.
DVDs labelled will also play on this player.
If you try to play any other DVD, the message
“Playback prohibited by area limitations.” will
appear on the TV screen. Depending on the
DVD, noregion code indication may be labelled
even though playing the DVD is prohibited by
area restrictions.
Example of discs that the player
cannot play
The player cannot play the following discs:
• All CD-ROMs (including PHOTO CDs)/CD-
Rs/CD-RWs other than those recorded in the
following formats:
–music CD format
–video CD format
–MP3 or JPEG format that conforms to
ISO9660* Level 1/Level 2, or its extended
format, Joliet
• Data part of CD-Extras
• DVD-RWs in VR mode
• DVD-ROMs
• DVD Audio discs
• HD layer on Super Audio CDs
* A logical format of files and folders on CD-ROMs,
defined by ISO (International Standard
Organization).
Also, the player cannot play the following discs:
• A DVD with a different region code.
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane tape
or a sticker still left on it.
Icon Meaning
Functions available for DVD
VIDEOs and DVD-RWs/
DVD-Rs in video mode or
DVD+RWs/DVD+Rs
FunctionsavailableforVIDEO
CDs, Super VCDs or CD-Rs/
CD-RWs in video CD format
or Super VCD format
Functions available for DATA
CDs (CD-ROMs/CD-Rs/CD-
RWs containing MP3* audio
tracks or JPEG files)
Functions available for music
CDs or CD-Rs/CD-RWs in
music CD format
Functions available for VHS
VIDEOs
Format of discs
DVD VIDEO
VIDEO CD
Music CD
ALL
SLV–DXXXX
00V 00Hz
00W NO.
0-000-000-00
XRegion code

7
Note
Some DVD-RWs/DVD-Rs, DVD+RWs/DVD+Rs or
CD-Rs/CD-RWs cannot be played on this player due to
the recording quality or physical condition of the disc,
or the characteristics of the recording device.
Furthermore, the disc will not play if it has not been
correctly finalized. For more information, see the
operating instructions for the recording device.
Note that discs created in the Packet Write format
cannot be played.
Note on playback operations of
DVDs and VIDEO CDs
SomeplaybackoperationsofDVDsandVIDEO
CDs may be intentionally set by software
producers. Since this player plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Also,refer to the
instructions supplied with the DVDs or VIDEO
CDs.
Music discs encoded with
copyright protection technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Notes about discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.

8Unpacking
Getting Started
Step 1 : Unpacking
Check that you have received the following items with the DVD-VCR:
• Remote commander • PERITEL cable
• R6 (size AA) batteries • Audio cord
(pinplug ×2 ypinplug ×2)
• Aerial cable • Video cord
(pinplug ×1 ypinplug ×1)
Check your model name
The instructions in this manual are for the 2 models: SLV-D950B and SLV-D910B. Check
your model name by looking at the rear panel of your DVD-VCR.
SLV-D950B is the model used for illustration purposes. Any difference in operation is
clearly indicated in the text, for example, “SLV-D950B only”.

Getting Started
9
Setting up the remote commander
Step 2 : Setting up the remote commander
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so
may cause a malfunction.
Inserting the batteries
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
You can use this remote
commander to operate this DVD-
VCR and a Sony TV. Buttons on
the remote commander marked
with a dot (•) can be used to
operate your Sony TV.
If the TV does not have the
symbol near the remote sensor, this
remote commander will not
operate the TV.
To operate Set TV / DVD·VIDEO to
the DVD player DVD·VIDEO, then press SELECT DVD and point at the remote sensor at
the DVD-VCR
the VCR DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor
at the DVD-VCR
your TV TV and point at the remote sensor at your TV
TV / DVD·VIDEO
Remote sensor
SELECT VIDEO
SELECT DVD
continued

10 Setting up the remote commander
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer’s code number.
Now you can use the ?/1, VOL +/–, PROG +/–, MUTING∗, TV/VIDEO, 0-9 and
-/--∗buttons to control your TV. You can also use the buttons marked with a dot (•)
to control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to
DVD·VIDEO.
∗for Sony TV only
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the
DVD-VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
1Set TV / DVD·VIDEO at the top of the remote commander to TV.
2Hold down ?/1, and enter your TV’s code number using the number buttons.
Then release ?/1.
Manufacturer Code number
Sony 01, 02
Akai 68
Ferguson 52
Grundig 10, 11
Hitachi 24
JVC 33
Loewe 45
Mivar 09, 70
NEC 66
Nokia 15, 16, 69
Panasonic 17, 49
Philips 06, 07, 08
Saba 12, 13
Samsung 22, 23
Sanyo 25
Sharp 29
Telefunken 36
Thomson 43
Toshiba 38
Manufacturer Code number

Getting Started
11
Connecting the DVD-VCR
Step 3 : Connecting the DVD-VCR
Note that “Advanced Hookups” (page 59) explains additional hookup methods that
will optimize the picture and sound for a true “hometheatre” experience.
1Disconnect the aerial cable from your
TV and connect it to on the rear
panel of the DVD-VCR.
2Connect of the DVD-VCR and the
aerial input of your TV using the
supplied aerial cable.
3Connect LINE-1 (EURO AV) on the
DVD-VCR and the PERITEL
connector on the TV with the supplied
PERITEL cable.
This connection improves picture and
sound quality. Whenever you want to
watch the DVD-VCR picture, press
TV/VIDEO to display the VCR
indicator in the display window.
4Connect the mains lead to the mains.
Mains
lead
LINE-1
(EURO AV)
ANTENNE
ENTREE
PERITEL
to mains
Aerial cable (supplied)
: Signal flow PERITEL cable (supplied)
continued

12 Connecting the DVD-VCR
Additional connection
To a satellite or digital tuner
with Line Through
Using the Line Through
function, you can watch
programmes from a satellite or
digital tuner connected to this
DVD-VCR on the TV even
when the DVD-VCR is turned
off. When you turn on the
satellite or digital tuner, this
DVD-VCR automatically sends
the signal from the satellite or
digital tuner to the TV without
turning itself on.
Notes
• This function may not work with some types of satellite or digital tuners.
• When the DVD-VCR is turned off, set the TV to the video channel.
1Connect the satellite or digital tuner to the LINE-3 connector as shown above.
2Turn off the DVD-VCR.
To watch a programme, turn on the satellite or digital tuner and the TV.
PERITEL cable (not supplied)
LINE-3 SORTIE
LIGNE
: Signal flow

Getting Started
13
Setting up the DVD-VCR with the Auto Set Up function
Step 4 : Setting up the DVD-VCR with the
Auto Set Up function
Before using the DVD-VCR for the first
time, set up the DVD-VCR using the Auto
Set Up function. With this function, you can
set TV channels, guide channels for the
ShowView system∗, and DVD-VCR clock
automatically.
∗SLV-D950B only
1Turn on your TV and set it to the video channel.
2Connect the mains lead to the mains.
The DVD-VCR automatically turns on and the
“SELECTION DU PAYS” menu appears.
V/v/B/b
ENTER
SET UP
Schweiz
RETURN
SELECTION DU PAYS
SET UP
ENTER
Français
b
B
continued

14 Setting up the DVD-VCR with the Auto Set Up function
To cancel the Auto Set Up function
Press SET UP.
Tip
• If you want to change the language for the on-screen display from the one preset in the Auto
Set Up function, see page 15.
Notes
• Whenever you operate the Auto Set Up function, some of the settings (ShowView, timer, etc.)
will be reset. If this happens, you have to set them again.
• Auto preset starts automatically only when you plug in the mains lead for the first time after
you purchase the DVD-VCR.
• If you want to use the Auto Set Up function again, select “Installation” in the “OPTION”
menu, then press V/v to select “Installation Auto”, then repeat step 3.
• Auto preset can be performed by pressing xon the unit continuously for 5 seconds or more
during power off with no tape inserted.
3Press B/b to select your country, then press
ENTER.
The DVD-VCR starts searching for all of the
receivable channels and presets them (in the
appropriate order for your local area).
If you want to change the order of the channels
or disable unwanted programme positions, see
“Changing/disabling programme positions” on page 21.
After the search is complete, the current time appears for any stations that
transmit a time signal. If the time does not appear, set the clock manually.
See “Setting the clock” on page 16.
ENTER
Merci d’attendre
RETURN
INSTALLATION AUTO
SET UP
10%

Getting Started
15
Selecting a language
Step 5 : Selecting a language
If you prefer an on-screen language other
than French, use the on-screen display to
select another language.
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1Press SET UP, then press V/v to select
(OPTION) and press ENTER.
2Press V/v to select “Langue”, then press
ENTER.
The “SELECTION LANGUE” menu appears.
3Press V/v to select the desired language, then press ENTER.
4Press SET UP to exit the menu.
V/v/B/b
ENTER
SET UP
SET UP
ENTER
Langue
Installation
Veille Auto
Messages Ecran
Réglages Utilisateur
L’horloge :Français
[ Non ]
[ Oui ]
RETURN
OPTION
SET UP
ENTER
v
V
ENTER
RETURN
SELECTION LANGUE
SET UP
ENTER
v
V
English
Français
Deutsch
B
Español
Italiano
Nederlands
ENTER
SET UP

16 Setting the clock
Step 6 : Setting the clock
You must set the time and date on the DVD-
VCR to use the timer features properly.
The Auto Clock Set function works only if a
station in your area is broadcasting a time
signal.
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1Press SET UP, then press V/v to select
(OPTION) and press ENTER.
2Press V/v to select “L’horloge”, then press
ENTER.
The “REGLAGE HORLOGE” menu appears.
3Press V/v to set the hour.
V/v/B/b
ENTER
SET UP
SET UP
ENTER
Langue
Installation
Veille Auto
Messages Ecran
Réglages Utilisateur
L’horloge :Français
[ Non ]
[ Oui ]
RETURN
OPTION
SET UP
ENTER
v
V
ENTER
12:00 1/JAN /2003 MER
Heure Date
Horloge Auto
Année
[ Oui ]
RETURN
REGLAGE HORLOGE
SET UP
ENTER
v
Vb B
ENTER
18:00 1/JAN /2003 MER
Heure Date
Horloge Auto
Année
[ Oui ]
RETURN
REGLAGE HORLOGE
SET UP
ENTER
v
Vb B

Getting Started
17
Setting the clock
Tips
• If you set “Horloge Auto” to “Oui”, the Auto Clock Set function is activated whenever the
DVD-VCR is turned off. The time is adjusted automatically by making reference to the time
signal from the station.
• To change the digits while setting, press Bto return to the item to be changed, and select the
digits by pressing V/v.
Note
• The clock display appears when VIDEO mode is selected with no tape inserted or when the
DVD-VCR is turned off.
4Press b to select the minutes and set the
minutes by pressing V/v.
5Set the day, month, and year in sequence by
pressing bto select the item to be set, and
press V/v to select the digits, then press b.
The day of the week is set automatically.
6Press V/v to select “Oui”for the setting of the
Auto Clock Set function.
The DVD-VCR automatically sets the clock
according to the time signal broadcast between
the channels PR 1 to PR 5.
If you do not need the Auto Clock Set function,
select “Non”.
7Press ENTER to confirm the setting.
8Press SET UP to exit the menu.
ENTER
18:30 1/JAN /2003 MER
Heure Date
Horloge Auto
Année
[ Oui ]
RETURN
REGLAGE HORLOGE
SET UP
ENTER
v
Vb B
ENTER
18:30 28/SEP /2003 DIM
Heure Date
Horloge Auto
Année
[ Oui ]
RETURN
REGLAGE HORLOGE
SET UP
ENTER
v
Vb B
ENTER
18:30 28/SEP /2003 DIM
Heure Date
Horloge Auto
Année
[ Oui ]
RETURN
REGLAGE HORLOGE
SET UP
ENTER
v
Vb B
ENTER
SET UP

18 Presetting channels
Step 7 : Presetting channels
If some channels could not be preset using
the Auto Set Up function, you can preset
them manually.
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1Press SET UP, then press V/v to select
(OPTION) and press ENTER.
2Press V/v to select “Installation”, then press
ENTER.
The “INSTALLATION” menu appears.
V/v/B/b
ENTER
SET UP
O RETURN
SET UP
ENTER
Langue
Installation
Veille Auto
Messages Ecran
Réglages Utilisateur
L’horloge :Français
[ Non ]
[ Oui ]
RETURN
OPTION
SET UP
ENTER
v
V
ENTER
Installation Manuelle
Installation Auto
RETURN
INSTALLATION
SET UP
ENTER
v
V

Getting Started
19
Presetting channels
3Press V/v to select “Installation Manuelle”,
then press ENTER.
4Press V/v to select the row which you want to
preset, then press b.
To display other pages for programme
positions 6 to 80, press V/v repeatedly.
5Press V/v to select “SYS.” if necessary.
6Press B/b to set “L/L’” or “B/G” if necessary.
• To receive broadcast in France, select
“L/L’”.
• To receive broadcast using the PAL system
(for example, in Germany or Switzerland),
select “B/G”.
7Press V/v to select “CANAL”, then press B/b
repeatedly until the channel you want is
displayed.
8Press V/v to select “NOM”, then press b.
ENTER
PR
2
1
3
4
5
CAN.
029
027
030
032
NOM
LMN –
AAB –
CDE –
I J K –
DEC
NON
NON
NON
NON
SYS.
L / L’
L / L’
L / L’
L / L’
RETURN
LISTE STATIONS TV
ENTER
CLEAR
MODIF.ST :
EFFACER :
V
vB
ENTER
PR
REGL.FIN
CANAL
DECODEUR
NOM
: 5
SYS. : L / L’
: –
: –––
: NON
: –– – –
RETURN
RECHERCHE MANUELLE
ENTERMEMOIRE :
V
vB b
ENTER
PR
REGL.FIN
CANAL
DECODEUR
NOM
: 5
SYS. : L / L’
: NON
RETURN
RECHERCHE MANUELLE
ENTERMEMOIRE :
: –
: –––
: –– – –
V
vB b
ENTER
PR
REGL.FIN
CANAL
DECODEUR
NOM
: 5
SYS. : L / L’
: NON
RETURN
RECHERCHE MANUELLE
ENTERMEMOIRE :
: –
: –––
: –– – –
V
vB b
ENTER
RETURN
ENTER
PR
REGL.FIN
CANAL
DECODEUR
NOM
: 5
SYS. : L / L’
: NON
RECHERCHE MANUELLE
MEMOIRE :
: –
: –––
: –– – –
V
vB b
ENTER
RETURN
ENTER
PR
REGL.FIN
CANAL
DECODEUR
NOM
: 5
SYS. : L / L’
: 033
: NON
RECHERCHE MANUELLE
MEMOIRE :
: –
: –– – –
V
vB b
continued

20 Presetting channels
If the picture is not clear
If the picture is not clear, you may use the Manual Fine Tuning (REGL.FIN)
function. After step 7, press V/v to select “REGL.FIN”. Press B/b to get a clear
picture. Then press ENTER.
Tips
• To set the programme position for the decoder, see “Setting the Canal Plus decoder” on
page 27.
• The DVD-VCR must receive channel information for station names to appear automatically.
Note
• When adjusting REGL.FIN, the menu may become difficult to read due to interference from
the picture being received.
9Enter the station name.
1Press V/v to select a character.
Each time you press V, the character
changes as shown below.
AtBt…tZt0t1t…t9
tA
2Press bto set the next character.
The next space flashes.
To correct a character, press B/b until the character you want to correct
flashes, then reset it.
You can set up to 4 characters for the station name.
10 Press ENTER to confirm the station name.
11 Press O RETURN, then press SET UP to exit the menu.
ENTER
RETURN
ENTER
PR
REGL.FIN
CANAL
DECODEUR
NOM
: 5
SYS. : L / L’
: NON
RECHERCHE MANUELLE
MEMOIRE :
: 033
: –
: O–––
V
vB b
ENTER
RETURN
SET UP