Sony KE-61MR1 User manual

SERVICE MANUAL
SPECIFICATIONS
MR1 CHASSIS
KE-61MR1
FLAT PANEL COLOR TV
Korea Model
MBT-MR1 PDM-6100
Panel System Plasma Display panel
Display resolution Display resolution:
Antenna 75 ohm external terminal for VHF/UHF
Television System NTSC
Channel Coverage VHF 2-13
UHF 14-69
CATV 1-125
Power Requirements 220V, 60 Hz
Inputs/Outputs
DVI-HDTV 1 terminal, 3.3V T.M.D.S., 50 ohms
The DVI-HDTV input terminal is compliant with the EIA-861 standard and is not
intended for use with personal computers.
Video (IN) 3 total (1 on front panel) 1 Vp-p, 75 ohms unbalanced, sync negative
S Video (IN) (1 on front panel) Y: 1 Vp-p, 75 ohms unbalanced, sync negative
C: 0.286 Vp-p (Burst signal), 75 ohms
Audio (IN) (1 on front panel) 500 mVrms (100% modulation)
Impedance: 47 kilohm
Component Video Input 2 (Y, P
B , P R ) Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative;
P
B : 0.7 Vp-p, 75 ohms
P
R : 0.7 Vp-p, 75 ohms
CONTROL S (OUT)
Variable/Fixed Audio (OUT) More than 408 m Vrms at the maximum volume
setting (Variable)
More than 408 mVrms (Fixed)
Impedance (output): 2 kilohms
1
1
3 total
6 total
1365 pixels (horizontal) ×768 pixels (vertical)

KE-61MR1 (K) 2
Sub woofer (OUT) 1
2
1
phono jack
RF Input
Converter
Supplied Accessories Remote Control RM-929Y
AAA (LR03) Batteries (2)
AC power code (2)
AC plug holder (1)
Display interface cable (1)
Antenna cable (1)
Cleaning cloth (1)
Screen Size (measured diagonally) 61 inches
Speaker Output 15 W ×2
Dimensions (W ×H ×D) PDM-6100
MBT-MR1
1797 ×937 ×110 mm
430 ×105 ×360 mm
Design and specifications are subject to change without notice.
Mass Display unit
PDM-6100: 71 kg
Media receiver unit
MBT-MR1: 7.5 kg
Power Consumption Display unit
PDM-6100: 705 W
Media receiver unit
MBT-MR1: 36 W
In Standby
In Use
Under 1.5 W
Monitor/Fixed Audio (OUT) 1

KE-61MR1 (K) 3
SAFETY CHECK-OUT
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly tran-
sistors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recom-
mend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC Leakage.
Check leakage as described right.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part
having a return to chassis, must not exceed 0.5 mA (500
microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOMs that are suitable. Nearly all bat-
tery operated digital multimeters that have a 2 V AC range
are suitable. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µF
AC
Voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
WARNING!!
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
!ON THE SCHEMATIC DIAGRAMS, EXPLODED
VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR
SAFE OPERATION. REPLACE THESE COMPONENTS
WITH SONY PARTS WHOSE PART NUMBERS AP-
PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-
MENTS PUBLISHED BY SONY. CIRCUIT ADJUST-
MENTS THAT ARE CRITICAL FOR SAFE OPERATION
ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE
PROCEDURES WHENEVER CRITICAL COMPONENTS
ARE REPLACED OR IMPROPER OPERATION IS
SUSPECTED.
AVERTISSEMENT!!
ATTENTION AUX COMPOSANTS RELATIFS À LA
SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET
UNE MARQUE ! SONT CRITIQUES POUR LA
SÉCURITÉ. NE LES REMPLACER QUE PAR UNE
PIÈCE PORTANT LE NUMÉRO SPECIFIÉ. LES
RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST
CRITIQUE POUR LA SÉCURITÉ DU
FONCTIONNEMENT SONT IDENTIFIÉS DANS LE
PRÉSENT MANUEL. SUIVRE CES PROCÉDURES
LORS DE CHAQUE REMPLACEMENT DE
COMPOSANTS CRITIQUES, OU LORSQU’UN
MAUVAIS FONCTIONNEMENT EST SUSPECTÉ.

KE-61MR1 (K) 4
DIAGNOSIS
(Reliability Self Diagnostic Display Specifications for MEDIA RECEIVER)
1) *Operation count is based on WDT.
*For flashes, the Power/Standby LED flashes in red.
*The flash period is based on the reliability standard.
The abnormal conditions are indicated by the following LED flashes.
Flash Count Error Display Name Error Description Oprating Detection Port
4 Fan Error Error detected for Detects Low when fan IC6200 pin #2
fan box function normally.
Detects High when Fan stops
abnormally
8 Digtal OVP OVP for DD Con- Detects High when normal. IC5210 pin #49
verter on DP board Detects Low when abnormal.
9 Panel Error Panel malfunction Detects during communication
detected with panel.
Repair part
•FAN
•FAN CONNECTOR
•SET 11V LINE
•SET 5V LINE
DP board
•Q1612, Q1613, Q1614
Panel Display Unit
*A failure part can be expected by the number of times of blink of LED.
*When two failures occur, the failure item generated previously is detected.
*When failure occurs simultaneously, an item with little number of times of blink is detected.
*In other than “Fan Error”, the unit is in standby state and blink LED at intervals of regulation.
In “Fan Error”, the unit is in a standby state after display for 1 minute about the message of “Fan problem –
Powering down”
every about 0.3s
about 3s
•Timing of LED blink (example of 4 times blink)
ON
OFF
In the following case, POWER LED of Media Receiver Box blinks at a fixed interval in ORANGE
•When the cable which connects between Media Receiver Box and Panel Display has fallen out.
•When the AC code for Panel Display has fallen out.
In the following case, POWER LED of Panel Display blinks at a fixed interval in ORANGE
•When the cable which connects between Media Receiver Box and Panel Display has fallen out.
•When the AC code for Media Receiver Box has fallen out.
2)
The example which judges whether it is failure
• POWER LED of Media Receiver Box: Blink 9 times in RED, and of Panel Display blink,
and No picture or Power circuit does not work →Large possibility that Panel Display is out of order.
•When turn on Media Receiver Box, and NO LED of Box shine
•When NO Blue LED of Box shine →Large possibility that Media Receiver Box is out of order.
Check SET5V or IIC line on H1 board.
•When turn on Media Receiver Box, and Fan does not work
→Large possibility that Media Receiver Box is out of order
3)
→Large possibility that Media Receiver Box is out of order.

KE-61MR1 (K) 5
TABLE OF CONTENTS
1. DISASSEMBLY ............................................ 1-1
1-1. DISPLAY UNIT (PDM-6100) ........................... 1-1
1-1-1. REAR COVER REMOVAL ......................... 1-1
1-1-2. G1 BOARD REMOVAL ............................... 1-2
1-1-3. F1, K2 AND P BOARDS REMOVAL ......... 1-2
1-1-4. G2 BOARD REMOVAL ............................... 1-3
1-1-5. SPEAKER BOX ASSY REMOVAL ............ 1-3
1-1-6. FILTER GLASS BRACKET ASSY
REMOVAL .................................................... 1-4
1-1-7. R1 BOARD REMOVAL ............................... 1-5
1-1-8. R2 BOARD REMOVAL ............................... 1-5
1-1-9. PLASMA DISPLAY PANEL ....................... 1-6
1-2. MEDIA RECEIVER UNIT (MBT-MR1) ......... 1-7
1-2-1. PANEL AND COVERS REMOVAL ........... 1-7
1-2-2. H1 BOARD REMOVAL ............................... 1-7
1-2-3. H4 BOARD REMOVAL ............................... 1-8
1-2-4. H3 BOARD REMOVAL ............................... 1-8
1-2-5. MS2 BOARD REMOVAL ............................ 1-9
1-2-6. H2 BOARD REMOVAL ............................... 1-9
1-2-7. A BOARD REMOVAL ................................. 1-10
1-2-8. B BLOCK ASSY REMOVAL ...................... 1-10
1-2-9. M, AD, AND AU BOARDS REMOVAL .... 1-11
1-2-10. AD AND AU BOARDS REMOVAL ........... 1-11
1-2-11. M BOARD REMOVAL ................................ 1-12
1-2-12. IFA BOARD REMOVAL ............................. 1-12
1-2-13. U1 BOARD REMOVAL ............................... 1-13
1-2-14. U2 BOARD REMOVAL ............................... 1-13
2. ADJUSTMENTS
2-1. VS, VD Voltage Adjustment (PDM-6100) ....... 2-1
2-1-1. Preparation for adjustment ............................. 2-1
2-1-2. Procedure for adjustment ............................... 2-1
2-2. White Balance Adjustment (PDM-6100) .......... 2-1
2-2-1. Measurement equipment ................................ 2-1
2-2-2. Measuring procedure ..................................... 2-1
3. TROUBLESHOOTING .................................. 3-1
3-1. DISPLAY UNIT (PDM-6100) ........................... 3-1
3-2. MEDIA RECEIVER UNIT (MBT-MR1) ......... 3-1
4. DIAGRAMS ................................................... 4-1
4-1. BLOCK DIAGRAMS ........................................ 4-1
4-1-1. DISPLAY UNIT (PDM-6100) ...................... 4-1
4-1-2. MEDIA RECEIVER UNIT (MBT-MR1C) .. 4-5
4-2. FRAME DIAGRAM .......................................... 4-15
4-3. CIRCUIT BOARDS LOCATION ..................... 4-16
4-3-1. DISPLAY UNIT (PDM-6100) ...................... 4-16
4-3-2. MEDIA RECEIVER UNIT (MBT-MR1) ..... 4-16
4-4. SCHEMATIC DIAGRAMS AND
PRINTED WIRING BOARDS ........................ 4-16
4-4-1. DISPLAY UNIT (PDM-6100) ...................... 4-17
(1) Schematic Diagrams of F1 Board .................. 4-17
(2) Schematic Diagram of G1 Board .................. 4-18
(3) Schematic Diagram of G2 Board .................. 4-20
(4) Schematic Diagram of K2 Board .................. 4-22
(5) Schematic Diagram of R1 and R2 Boards .... 4-24
(6) Schematic Diagrams of P Board .................... 4-25
4-4-2. MEDIA RECEIVER UNIT (MBT-MR1) ..... 4-30
(1) Schematic Diagrams of A Board ................... 4-30
(2) Schematic Diagrams of AD Board ................ 4-33
(3) Schematic Diagram of AU Board .................. 4-38
(4) Schematic Diagrams of BM1C Board ........... 4-40
(5) Schematic Diagrams of DICA Board ............ 4-43
(6) Schematic Diagram of DP Board .................. 4-49
(7) Schematic Diagram of H1 Board .................. 4-51
(8) Schematic Diagram of H2 Board .................. 4-53
(9) Schematic Diagram of H3 and H4 Boards .... 4-55
(10) Schematic Diagram of IFA Board ................. 4-56
(11) Schematic Diagrams of M Board .................. 4-58
(12) Schematic Diagram of MS2 Board ................ 4-64
(13) Schematic Diagram of U1 Board .................. 4-66
(14) Schematic Diagram of U2 Board .................. 4-68
4-5. SEMICONDUCTORS ....................................... 4-69
5. EXPLODED VIEWS ...................................... 5-1
5-1. DISPLAY UNIT-1 (PDM-6100) ....................... 5-2
5-2. DISPLAY UNIT-2 (PDM-6100) ....................... 5-3
5-3. MEDIA RECEIVER UNIT-1 (MBT-MR1) ...... 5-4
5-4. MEDIA RECEIVER UNIT-2 (MBT-MR1) ...... 5-6
5-5. PACKING MATERIALS FOR
DISPLAY UNIT (PDM-6100) ........................... 5-7
5-6. PACKING MATERIALS FOR
MEDIA RECEIVER UNIT (MBT-MR1) ......... 5-8
6. ELECTRICAL PARTS LIST ........................ 6-1

KE-61MR1 (K) 1-1
1-1. DISPLAY UNIT (PDM-6100)
1-1-1. REAR COVER REMOVAL
SECTION 1
DISASSEMBLY
4Rear cover
2Six screws
(+PSW 5x16)
2Six screws
(+PSW 5x16)
1Six screws
(+PSW 4x12)
1Four screws
(+PSW 4x12)
1Six screws
(+PSW 4x12)
1Four screws
(+PSW 4x12)
3Five screws
(+PSW 3x8)

KE-61MR1 (K) 1-2
1-1-2. G1 BOARD REMOVAL
1-1-3. F1, K2 AND P BOARDS REMOVAL
3Two screws
(+BVTP 3x12)
4G1 board
1Two screws
(+PSW 4x12)
1Two screws
(+PSW 4x12)
2G1 bracket
2F1 board
1Two screws
(+PSW 3x8)
7Two screws
(+PSW 3x8)
5Two screws
(+PSW 3x8)
3Two screws
(HEX)
4Two screws
(M2.6 S HEAD)
8K2 board
6P board

KE-61MR1 (K) 1-3
1-1-4. G2 BOARD REMOVAL
4G2 board
2G2 bracket
3Three screws
(+BVTP 3x12)
1Three screws
(+PSW 4x12)
1Three screws
(+PSW 4x12)
1-1-5. SPEAKER BOX ASSY REMOVAL
5Speaker box (L) assy
4Speaker box (RL)
Speaker
terminal (B)
Speaker terminal (A)
Speaker terminal (A)
9Speaker box (RR)
0Speaker box (R) assy
2Four screws
(+PSW 4x10)
1Ten screws
(+BTP 4x18)
8Six screws
(+BVTP 4x16)
3Six screws
(+BVTP 4x16)
6Ten screws
(+BTP 4x18)
7Four screws
(+PSW 4x10)
Speaker
terminal (B)

KE-61MR1 (K) 1-4
1-1-6. FILTER GLASS BRACKET ASSY REMOVAL
!ª Two fixed screws
!¶ Two fixed screws
(+KTP 3x8)
@º Bar (V)
!• Bar (V)
1Four screws (+BVTP 4x12)
8Four screws
(+BVTP 4x12)
4Four screws
(+PSW 4x12)
5Two screws
(+BVTP 4x12)
!¡ Two screws (+BVTP 4x12)
!º Four screws (+PSW 4x12)
2Two screws
(+PSW 4x12)
7Two screws
(+PSW 4x12)
!£ Six fixed screws
!∞ Six fixed screws
@¡ Filter glass
bracket assy
3Filter bracket assy (V)
9Filter bracket assy (V)
!™ Filter bracket assy (H)
6Filter bracket
assy (H)
!§ Bar (H) assy
!¢ Bar (H) assy (UPPER)

KE-61MR1 (K) 1-5
1-1-7. R1 BOARD REMOVAL
1-1-8. R2 BOARD REMOVAL
2Filter bracket (V) block assy
4R1 board
3PC board spacer
1Two screws
(+P 3x16)
2Filter bracket (H) block assy
1Four screws
(+PSW 4x12)
3PC board spacer
4R2 board

KE-61MR1 (K) 1-6
1-1-9. PLASMA DISPLAY PANEL
2Filter bracket (V) block assy
61 inch optical filter
1Two screws
(+P 3x16)
3Four screws (+PSW 4x12)
4Filter bracket (H) block assy
561 inch plasma display panel

KE-61MR1 (K) 1-7
1-2. MEDIA RECEIVER UNIT (MBT-MR1)
1-2-1. PANEL AND COVERS REMOVAL
1-2-2. H1 BOARD REMOVAL
!∞ Rear panel
6Bottom cover assy
9Front panel assy
1Two screws
(+PSW 3X8)
3Two screws
(+PSW 3X8)
!¡ Two screws (HEX)
!™ Two screws (HEX)
!£ Four screws (+PSW 3X8)
!¢ Two screws (+PSW 3X8)
0Two screws GRIP, M2.6 S'HEAD(EG)
3Two screws
(+PSW 3X8)
7Eight screws
(precision)
7Four screws
(precision)
2Screw
(+PSW 3X8)
4Screw
(+PSW 3X8)
5Top cover assy
8Top chassis assy
1Two screws
(+BVTP 3X12)
2H1 board
1Two screws
(+BVTP 3X12)
Front panel

KE-61MR1 (K) 1-8
1-2-3. H4 BOARD REMOVAL
1-2-4. H3 BOARD REMOVAL
1Two screws
(+BVTP 3X12)
2H4 board
Front panel
1Three screws
(+BVTP 3X12)
2H3 board
Front panel

KE-61MR1 (K) 1-9
1-2-5. MS2 BOARD REMOVAL
1-2-6. H2 BOARD REMOVAL
3Two screws
(+BVTP 3X12)
4MS2 board
Front panel
1Two screws
(+BVTP 3X12)
2MS bracket
1Two screws
(M 3X8),P,SW (+)
2H2 board

KE-61MR1 (K) 1-10
1-2-7. A BOARD REMOVAL
1-2-8. B BLOCK ASSY REMOVAL
1Screw
(M 3X8),P,SW (+)
1Two screws
(M 3X8),P,SW (+)
1Two screws
(M 3X8),P,SW (+)
2A board
1B block assy

KE-61MR1 (K) 1-11
1-2-9. M, AD, AND AU BOARDS REMOVAL
1-2-10. AD AND AU BOARDS REMOVAL
2Shield case
1Two screws
(+PSW 3x8)
1Two screws
(PSW 3x8)
3Four screws
(PSW 3x8)
Shield upper
Shield main
3Two screws
(PSW 3x8)
4AD board
2AU board

KE-61MR1 (K) 1-12
1-2-11. M BOARD REMOVAL
1-2-12. IFA BOARD REMOVAL
2Screw
(+PSW 3x8)
3M board
1Shield case (upper)
Shield case (main)
1IF shield sheet
3IFA board
B block assy
2Screw
(+PSW 3x8)

KE-61MR1 (K) 1-13E
1-2-13. U1 BOARD REMOVAL
1-2-14. U2 BOARD REMOVAL
1Four screws
(+BVTP 3x12)
2U1 board
3Core (FPC)
1Two screws
(+BVTP 3x12)
2U2 board
Rear panel

KE-61MR1 (K) 2-1
SECTION 2
ADJUSTMENTS
2-1. VS, VD Voltage Adjustment (PDM-6100)
2-1-1. Preparation for adjustment
1. Slide the DIP switch (S3201) No. 8 of P board to on position
with no silkscreen mark r.
2. Connect a digital voltmeter to the following terminals of G
board.
VS voltage=G board TP1701 (VS)-TP1502 (GND)
VD voltage=G board TP1501 (VD)-TP1502 (GND)
3. Connect a AC cord in DISPLAY UNIT.
4. Perform the adjustment in 10 seconds after connecting the
cord.
2-1-2. Procedure for adjustment
1. Slide the DIP switch (S3201) No. 7 of P board to on position
with no silkscreen mark r.
2. Confirm the lighting of SONY LOGO LED.
3. Adjust the VS voltage to the following voltage value.
VS voltage of proper value for each model.
Ex.) VS proper value=185V thru 185.6V at 185V.
(Check the proper value with a seal on upper left of panel
unit. Refer to right Fig.)
4. Adjust the VD voltage to the following voltage value.
VD voltage ±0.3V of proper value for each model.
Ex.) VD proper value=64.7V thru 65.3V at 65.0V.
(Check the proper value with a seal on upper left of panel
unit. Refer to right Fig.)
5. Check a Fan rotation.
6. Slide the DIP Switch (S3201) No. 7 of P board to the off
position with the silkscreen mark r.
7. Slide the DIP Switch (S3201) No. 8 of P board to the off
position with the silkscreen mark r.
8. Disconnect an AC cord of DISPLAY UNIT.
9. Reconnect the AC cord in one second.
10. Assure that “POWER ON/STANDBY” LEDs is flashing
amber.
+6V
–0V
Rear cover assy
SERIAL No.
301201440
Vd=65V
Vs=193.4V
CODE AA-01
BAR CODE SEAL
Panel unit
2-2. White Balance Adjustment (PDM-6100)
2-2-1. Measurement equipment
1. Color analyzer (CA-100 manufactured by MINOLTA)
2. Signal generator (ASTRO DESIGN VG-828D)
2-2-2. Measuring procedure
1. Dab the W/B adjustment jig (CA-100) at the glass face of the
panel.
2. Connect the Signal generator (VG-828D) to the DVI
terminal.
3. Input All-white signal and set the picture mode to
DYNAMIC.
4. Select”PNLCTRL” in the service mode menu and set “0
WBNO” at “0”
5. Select “SCNR” “SCNB” of “PDPWB” in the service mode
menu, and then adjust following W/B standardized values
of 6500K, 8000K, 9300K, 10000K and 13550K to following
values of X/Y.
W/B standardized values:
6. After adjusting the values, at the values of the “SCNR” or
“SCNB” exceeding 128 (initialize value).
1) Reset a lager value of the “SCNR” or “SCNB” at 128.
2) Set the White Balances with the last of items and “SCNG”
to the X/Y values above.
7. After the above step, when these item are nonqualified
following conditions, set the largest one at 128 and readjust
the White Balance with the last two item.
1) No one of “SCNR”, “SCNB” and “SCNG” exceeding 128
2) Confirm the item value 128 at least one item
8. As a result above, input the sequential number of value to the
“SCNR”, “SCNB” and “SCNG”.
9. Repeat the same step 5 thru 8 for the W/B 1 thru 4 after
setting the “0 WBNO” at each W/B number.
10. Input following signals from the Signal generator (VG-
828D).
1) All-white signal (255/255) input
Y (luminance)=45cd/m2or more
2) 1/25Window (255/255) input
Y (luminance)=45cd/m2or more
• Service mode lists
Caution: 1. Setting functions of Display section are displayed
with yellow OSD.
2. Be careful not to set DATA in the yellow-covered
OSD menu. The setting will be memorized.
3. items are not required adjustment or are banned
adjustment.
<SEAL POSITION>
6500K+8MPCD
0
0.3133 ± 0.003
0.3297 ± 0.003
8000K+8MPCD
1
0.2944 ± 0.003
0.3100 ± 0.003
W/B
X
Y
9300K+8MPCD
2
0.2838 ± 0.003
0.2981 ± 0.003
10000K
3
0.2806 ± 0.003
0.2883 ± 0.003
13550K
4
0.2684 ± 0.003
0.2700 ± 0.003

KE-61MR1 (K) 2-2E
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPWB 00 SCNR Sub contrast RED gain 0-255 128 CXD9738R
01 SCNG Sub contrast GREEN gain 0-255 128
02 SCNB Sub contrast BLUE gain 0-255 128
03 SBRR Sub brightness RED 0-255 128(Fix)
04 SBRG Sub brightness GREEN 0-255 128(Fix)
05 SBRB Sub brightness BLUE 0-255 128(fix)
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPSHAP 00 CRMD
01 HTAP
02 VTAP
03 AGCM
04 EDDL
05 EDGA
06 EDNM
07 EDDE
08 DHVS
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPGMMA 00 GMMA
01 GMR0
02 GMR1
03 GMR2
04 GMR3
05 GMR4
06 GMR5
07 GMR6
08 GMR7
09 GMR8
10 GMR9
11 GMRA
12 GMG0
13 GMG1
14 GMG2
15 GMG3
16 GMG4
17 GMG5
18 GMG6
19 GMG7
20 GMG8
21 GMG9
22 GMGA
23 GMB0
24 GMB1
25 GMB2
26 GMB3
27 GMB4
28 GMB5
29 GMB6
30 GMB7
31 GMB8
32 GMB9
33 GMBA
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPPLE 00 PLE0
01 PLE1
02 PLE2
03 PLE3
04 PLE4
05 PLE5
06 PLE6
07 PLE7
08 PLE8
09 PLE9
10 PLEA
11 LMAX
12 LMIN
13 GAIN
14 OFFS
15 SAFL
16 LIFH
17 SPLE
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPDYPIC 00 TLVL
01 TFVL
02 THLD
03 PLVL
04 PFIL
05 PHLD
06 PGUP
07 PGDN
08 PHIS
09 PGAN
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPDISPOS 00 VAR1
01 VAR2
02 HTLL
03 HTLM
04 VTLL
05 VTLM
06 HS1L
07 VS1M
08 HE1L
09 HE1M
10 VS1L
11 VS1M
12 VE1L
13 VE1M
14 HS2L
15 HS2M
16 HE2L
17 HE2M
18 VS2L
19 VS2M
20 VE2L
21 VE2M
22 V1SH
23 V1DT
24 V1AP
25 V2SH
26 V2DT
27 V2AP
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPSTAT 00 SRNU
01 SRNL
02 ROMV
03 OPTM
Category Item Function Data range Initialize value Device Name
No. Name (Slave Address)
PDPOTHER 00 DTMD
01 VIDT
02 CODE
03 ORBT
04 FV