Sony PCG-SRX77 User manual

Confidential
PCG-SRX77/SRX77P
SERVICE MANUAL
NOTEBOOK COMPUTER
9-874-456-01
S400
For American Area
US Model
Canadian Model
• Design and specifications are subject to
change without notice.
Lineup : PCG-SRX77
PCG-SRX77P Illust : PCG-SRX77P
Ver 1-2002A
Revision History

— 2 —
PCG-SRX77/SRX77P (AM)
Information in this document is subject to change without notice.
Sony and VAIO are trademarks of Sony. Intel logo and Intel Inside
logo are registered trademarks of Intel Corporation. Pentium MMX
is a trademark of Intel Corporation. Microsoft, MS-DOS, Windows,
the Windows 95 and Windows 98 logo are trademarks of Microsoft
Corporation.
All other trademarks are trademarks or registered trademarks of
their respective owners. Other trademarks and trade names may be
used in this document to refer to the entitles claiming the marks and
names or their produces. Sony Corporation disclaims any proprietary
interest in trademarks and trade names other than its own.
Service and Inspection Precautions
1. Obey precautionary markings and instructions
Labels and stamps on the cabinet, chassis, and components identify areas
requiring special precautions. Be sure to observe these precautions, as well
as all precautions listed in the operating manual and other associated
documents.
2. Use designated parts only
The set’s components possess important safety characteristics, such as
noncombustibility and the ability to tolerate large voltages. Be sure that
replacement parts possess the same safety characteristics as the originals.
Also remember that the 0mark, which appears in circuit diagrams and
parts lists, denotes components that have particularly important safety
functions; be extra sure to use only the designated components.
3. Always follow the original design when mounting
parts and routing wires
The original layout includes various safety features, such as inclusion of
insulating materials (tubes and tape) and the mounting of parts above the
printer board. In addition, internal wiring has been routed and clamped so
as to keep it away from hot or high-voltage parts. When mounting parts or
routing wires, therefore, be sure to duplicate the original layout.
4. Inspect after completing service
After servicing, inspect to make sure that all screws, components, and wiring
have been returned to their original condition. Also check the area around
the repair location to ensure that repair work has caused no damage, and
confirm safety.
5. When replacing chip components...
Never reuse components. Also remember that the negative side of tantalum
capacitors is easily damaged by heat.
6. When handling flexible print boards...
• The temperature of the soldering-iron tip should be about 270C.
• Do not apply the tip more than three times to the same pattern.
• Handle patterns with care; never apply force.
Caution: Remember that hard disk drives are easily damaged by
vibration. Always handle with care.
Caution Markings for Lithium/Ion Battery - The following or similar
texts shall be provided on battery pack of equipment or in both the
operating and the service instructions.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer. Discard used batteries according to the
manufacturer’s instructions.
CAUTION: The battery pack used in this device may present a fire
or chemical burn hazard if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
Dispose of used battery promptly.
Keep away from children.
CAUTION: Changing the back up battery.
• Overcharging, short circuiting, reverse charging, multilation or
incineration of the cells must be avoided to prevent one or more of
the following occurrences; release of toxic materials, release of
hydrogen and/or oxygen gas, rise in surface temperature.
• If a cell has leaked or vented, it should be replaced immediately
while avoiding to touch it without any protection.
Confidential
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

—3 —
TABLE OF CONTENTS
CHAPTER 1. REMOVAL
1-1. Flowchart ......................................................................... 1-1
1-2. Main Electrical Parts Location Diagram ......................... 1-1
1-3. Removal ........................................................................... 1-2
1. HDD, Lid (HDD) ............................................................. 1-2
2. Keyboard Unit (J), Housing (Palmrest) Assy .................. 1-3
3. Pad Touch, Speaker, SWX-86 Board,
IFX-175 Board, Dial Unit Jog ......................................... 1-4
4. Foot (R) Rear, Foot (L) Rear, Foot (R) ............................ 1-5
5. Display Assy .................................................................... 1-5
6. Holder (Heat Sink), Heat Sink, Fan DC, Card Modem ... 1-6
7. Card Wireless Lan ............................................................ 1-6
8. MBX-57 Board, Harness (With DC Jack) ....................... 1-7
9. Escutcheon (L) Assy, IFX-177 Board, Harness RJ-45,
Escutcheon (R), CNX-148 Board, CNX-149 Board,
IFX-178 Board ................................................................. 1-8
10. LCD Section –Made by TS –......................................... 1-9
1. Housing (Bezel) Assy .................................................. 1-9
2. LCD Unit Inverter Unit, Tilt (L), Tilt (R),
Housing (Display) Assy ............................................. 1-10
(to 1-10)
CHAPTER 2. SELF DIAGNOSTICS ...................... 2-1
(to 2-1)
CHAPTER 3. BLOCK DIAGRAM ........................... 3-1
(to 3-2)
CHAPTER 4. FRAME HARNESS DIAGRAM ........ 4-1
(to 4-2)
CHAPTER 5. EXPLODED VIEWS AND
PARTS LIST
5-1. Main Section .................................................................... 5-2
5-2. LCD Section –Made by TS –.......................................... 5-5
(to 5-6)
Section Title Page
PCG-SRX77/SRX77P (AM)
Confidential
History of the changes is shown as the
“Revision History”at the end of this data.

1-1 PCG-SRX77/SRX77P (AM)
Confidential
CHAPTER 1.
REMOVAL
1-1. Flowchart
•P XX means pages that appears in this manual.
•Remember that hard disk drives are easily damaged by vibration. Always handle with care.
1-2. Main Electrical Parts Location Diagram
POWER
OFF HDD KEYBOARD
UNIT (J)
HOUSING
(PARMLEST)
ASSY
CARD
MODEM HEAT SINK FAN DC CARD
WIRELESS
LAN
CNX-148
BOARD
CNX-149
BOARD
IFX-177
BOARD
IFX-178
BOARD
MBX-57
BOARD
DISPLAY
ASSY
FOOT (R) REAR/
FOOT (L) REAR
FOOT (R) HOUSING
(BEZEL)
ASSY
LCD UNIT INVERTER
UNIT
SPEAKER
IFX-175
BOARD
SWX-86
BOARD
DIAL UNIT
JOG
PAD
TOUCH
P 1-5 P 1-5 P 1-5
P 1-7P 1-6
P 1-8
P 1-8
P 1-8
P 1-8
P 1-6P 1-6P 1-6
P 1-4
P 1-4
P 1-4
P 1-4
P 1-4
P 1-3P 1-3P 1-2
P 1-9 P 1-10 P 1-10
Speaker
DC Fan
Card, Modem
Card, Wireless LAN
DC Jack
RJ-45 Connector
HDD CNX-148 Board
CNX-149 Board
IFX-175 Board
IFX-178 Board
IFX-177 Board
SWX-86 Board
MBX-57 Board
LCD Assy
Speaker
Inverter Unit

1-2PCG-SRX77/SRX77P (AM)
Confidential
1-3. Removal
1. HDD, Lid (HDD)
2Lid (HDD)
MBX-57 Board
CN1011
1ACE (M2X5), Lock (X2)
3ACE (M2X4)(DIA.4.6), Lock (X2)(Gold)
2Blacket (HDR)
1Screw M3X4
(X2) (Gold)
4Blacket (HDF)
5PWB, Flexible Print (For HDD)
5HDD
HDD
Gasket (A)
4
3Screw M3X4 (Gold)

1-3 PCG-SRX77/SRX77P (AM)
Confidential
2. Keyboard Unit (J), Housing (Palmrest) Assy
8
6
5
5
1ACE (M2X5), Lock (X2)
2ACE (M2X5), Lock (X2)
3ACE (M2X5), Lock (X2)
4ACE (M2X5), Lock (X3)
q; ACE (M2X4)(DIA.4.6)
Lock (X2) (Gold)
9Blind,Screw (X2)
Claws
Claw
Claw
7Keyboard Unit (J)
qs Housing (Palmrest)
Assy
Claws
qd qa
The claws are released by pressing
the keyboard unit from rear of the
Housing (palmrest) assy.
MBX-57 Board
CN1800
MBX-57 Board
CN1901

1-4PCG-SRX77/SRX77P (AM)
Confidential
3. Pad Touch, Speaker, SWX-86 Board, IFX-175 Board, Dial Unit Jog
3Speaker
(with Harness)
6Speaker
(with Harness)
qa IFX-175 Board
IFX-175 Board
CN5500
ws Cover (TP)
wf Plate (TP)
Ten Claws
Five Claws
Housing (Palmrest)
wd Pad, Touch
wg Escutcheon (Jog)
2Holder (SP)
5Holder (SP)
Sheet (Ground Plate)
Tape (Harness) Sheet (Ground Plate)
1
4
87
9FFC (SWX-IFX)
q; ACE (M2X4), Lock(X2)(Gold)
ql Dial Unit, Jog
w; ACE (M2X4), Lock (Gold)
qk ACE (M2X4), Lock (X2)(Gold)
qf
qs
qd FFC of the Dial Unit,Jog
qh FFC
(SWX-TP)
qj FFC (MBX-SWX)
qg
wa SWX-86 Board

1-5 PCG-SRX77/SRX77P (AM)
Confidential
4. Foot (R) Rear, Foot (L) Rear, Foot (R)
5. Display Assy
3ACE (M2X4)(DIA.4.6),
Lock (Gold)
7Screw +B 2X4
4ACE (M2X4)(DIA.4.6), Lock (Gold)
6Foot (L), Rear
5Foot (R), Rear
1Foot (R)
2Foot (R)
8Screw +B 2X4
3Screw +B 2X4
2ACE (M2X4)(DIA.4.6),
Lock (Gold)
4Screw +B 2X4
15
6Display Assy
MBX-57 Board
CN1000

1-6PCG-SRX77/SRX77P (AM)
Confidential
6. Holder (Heat Sink), Heat Sink, Fan DC, Card Modem
7. Card Wireless Lan
1ACE (M2X3)(DIA.4.6), Lock (X2)(Gold)
Plate (Heat Sink), Ground
MBX-57 Board
CN1500
MBX-57 Board
CN300
6Holder (Heat Sink)
5ACE (M2X4)(DIA.4.6), Lock (X2)(Gold)
9ACE (M2X8), Lock (X2)(Silver)
qa Heat Sink
Sheet (Heat Sink)
q; Sheet (USB)
4Card, Modem
qs Fan, DC
2
3
qs
6Card, Wireless Lan
3Card, coaxial (with UFU Connector) Tape (Harness)
CNX-149 Board
CN4599
1
4
2
5
4

1-7 PCG-SRX77/SRX77P (AM)
Confidential
8. MBX-57 Board, Harness (With DC Jack)
qd Cover (BR)
qs
q; Bolt (X2) (Gold)
qa Cable, Flexible Flat
(MBX-CNX2)
2Harness (With DC Jack)
4Bracket (K)
3ACE (M2X4)(DIA.4.6),
Lock (Gold)
1ACE (M2X4)(DIA.4.6),
Lock (Gold)
6Harness (LCD)
9ACE (M2X4)(DIA.4.6), Lock (X3)(Gold)
7Harness, RJ-45
8ACE (M2X3), Lock (X2)(Gold)
qf MBX-57 Board
MBX-57 Board
CN2501
MBX-57 Board
CN1000
MBX-57 Board
CN1902
MBX-57 Board
CN2602
MBX-57 Board
CN1700
5Cable, Flexible Flat

1-8PCG-SRX77/SRX77P (AM)
Confidential
9. Escutcheon (L) Assy, IFX-177 Board, Harness RJ-45, Escutcheon (R),
CNX-148 Board, CNX-149 Board, IFX-178 Board
3Cable,
Flexible flat
qs IFX-177 Board
qf Harness, RJ-45
qd Cable, coaxial (with UFL Connector)
qa Escutcheon (L) Assy
9CNX-149 Board
CNX-149 Board
CN4500
IFX-178 Board
CN7001
2CNX-148 Board
CNX-148 Board
CN4000
Plate(ANT)
8ACE (M2X4)(DIA.4.6),
Lock (Gold)
1ACE (M2X4)(DIA.4.6), Lock (Gold)
0Harness (2Pin)
5ACE (M2X4)(DIA.4.6),
Lock (Gold)
6IFX-178 Board
7Cable, coaxial (With UFL Connector)
4Escutcheon (R)

1-9 PCG-SRX77/SRX77P (AM)
Confidential
10. LCD Section –Made by TS –
1. Housing (Bezel) Assy
How to release the claw C
Order of releasing the claws A→B→C
Order of locking the claws C→B→A
Pull the Housing (Bezel) Assy as
shown to release the claw C
1Blind (LCD) Screw
C
BClaws (X2)
BClaws (X2)
CClaws (X3)
Housing (Bezel) Assy
Housing (Display) Assy
5Housing (Bezel) Assy
3Blind (LCD) Screw
4ACE (M2) (DIA.4.6), Lock (X2) (Black)
2ACE (M2) (DIA.4.6),
Lock (X2) (Black)
7Cover (R)
8ACE (M2), Lock (Gold)
6ACE (M2), Lock (Gold)
9Cover (L)
AClaws (X5)

1-10PCG-SRX77/SRX77P (AM)
Confidential
(END)
2. LCD Unit, Inverter Unit,Tilt (L), Tilt (R), Housing (Display) Assy
1ACE (M2), Lock (X2) (Gold)
8ACE (M2), Lock (X2) (Gold)
0ACE (M2), Lock (X2) (Gold)
qd Housing (Display) Assy
4LCD (10.4XGA)
qs Latch
qa Tilt (R)
9Tilt (L)
5LCD
Harness
2ACE (M2), Lock (X2) (Gold)
7Inverter Unit
3
Clamp, LCD
6
Sheet
(LCD,Harness)
To remove the harness from
the Tilt (L), remove it in the
direction of the arrow.

2-1 PCG-SRX77/SRX77P (AM)
Confidential
CHAPTER 2.
SELF DIAGNOSTICS
Please confirm “Self Diagnostics”method which will be informed you with distribution
of “Self Diagnostics”software.
ATTENTION
(END)

PCG-SRX77/SRX77P (AM)
Confidential
3-23-1
CHAPTER 3.
BLOCK DIAGRAM
(END)
MODEM
-m
800/550MHz
LV
Intel Pentium III -m
800/550MHz
LV
Intel 82815EM
GMCH
VCH
Intel /
FW82807A
1
Intel
DA825 2ET
i.Link
TI/
15CC3CT
Card controller
RICOH R5C475II
FWH
SST
49LF004A
HDD
CN 50P
30P
CN 10P
CN P
Battery
11.1V/3 00mAh
CN P
External CRT
CN14P
ATF
AD1030A
I/O Expander
O2MICRO
OZ998S
CN2 P
CN2 P
CN24P
SONY
10.4 XGA
LCD &
INVERTER
CN 4P
RJ-45
CN 10P CN 10P
Memorystick
Slot
CN17P
CN17P
Amp
RJ-11
&Korea
KeyBoard
Touc Pad
JOG
Intel 82801BAM
ICH-2m
2P
CN 2P
CN
CN
30PCN
BlueTooth
Ant
W-LAN
MiniPCI
Module
Type III
ant L
(main)
µ-DIMM
Memory
Module
Audio Codec
(AC '97)
USB CN
CN4P
JogDial
Encoder
CardBus/16bitCard
PC Card
Connector
1 Slot
KBC/EC
HITACH
H8/2149
Tualatin LV/ULV + 815E
Tualatin LV/ULV + 815EM architecture.
Clock Generator
IMI/C9835AT
i.LINK
CN 10P
BlueTooth
Module
Memorystick
Controller
STmicro
M29W200BB70N
MBX-57
MBX-57
1-682-713-11
1-682-713-11
Z -121
Z -121
1-720-383-11
IFX-175
IFX-175
1-682-697-11
CNX-148
CNX-148
1-682-701-11
1-682-701-11
IFX-178.01(RIGHT)
IFX-178.01(RIGHT)
1-682-700-11
IFX-177.01 (LEFT)
1-682-699-11
CNX-149.01
CNX-149.01
1-680-739-11
Z -122
Z -122
1-720-384-11
IFX-175.01
IFX-175.01
1-682-697-11
ant R
(Sub)
1-719-567-11
WX-86.11
WX-86.11
1-682-703-11
DC out
PCI Bus
Memory Bus PC=100
LPC Bus
AC Link
USB 1.1
USB 1.1
USB 1.1 USB 1.1
BckBtn
Speaker L
Speaker L Speaker R
Mic CN
HeadPhone CN
USB 1.1
Ultra ATA /100
25 MB Tech
128MB DIMM
25 MB Tech
128MB DIMM
µ-DIMM
Memory Slot
Mini PCI
Connector
TypeIII

PCG-SRX77/SRX77P (AM)
Confidential
(END)
4-24-1
CHAPTER 4.
FRAME HARNESS DIAGRAM
RAM
12 1
PAD, TOUCH
J1
HARD DISK
DIAL UNIT, JOG
KEY BOARD
LCD HARNESS
INVERTER
LCD
L Side
2
1
30
29
1
2
23
24
CN1500
CN1800
126
CN1901
21
CN300
1
10
CN2603
CN2502
CN2600
2
1
30
29
20
19
2
1
CN1000
CN1700
14
CN2200
1
9
2
10
CN1001
123
143
144
1
2
1
CN2602
17 18
12
CN1400
CN4501
CN800
CN2100 CN4001
CN4002
CN4003
1
18
CN4000
IFX-175 Board
(Side-A)
CNX-149 Board
(Side-A)
IFX-177 Board
(Side-A)
CNX-148 Board
(Side-A)
IFX-178 Board
(Side-A)
61
CN1011
CN2500
21
21
50 49
VANADIUM-LITHIUM
BATTERY
1
5
2
6
1
1
5
26
2
CN4500
CN4599
112 12126 17
110
1
2
CN5000
CN5001
CN5002
CN5004
CN5500
EXTERNAL MIC IN
HEADPHONE
USB
MEMORY STICK
CN5005 CN5003
10
1
SPEAKER
SPEAKER
2
1
30
29
J1
CARD, MODEM
CN7001
CN6500
MBX-57 Board
(Side-A)
DC FAN
DC IN
NETWORK
PHONE
IEEE 1394 i.LINK
DC OUT
DISPLAY
CARD, WIRELESS LAN
BATTERY PACK
(OPTION)
HARNESS, RJ-45 HARNESS, (WITH DC JACK)
S5500
POWER
SWITCH
(SRX7 Model Only)
CN1902
From board to connector (direct connection)
Harness (connector at both end)
Harness (soldered at one end)
Connectors soldered on board and appearing on the panel
CN2501
R Side

5-1
CHAPTER 5.
EXPLODED VIEWS AND PARTS LIST
NOTE:
•The mechanical parts with no reference number in the
exploded views are not supplied.
•Items marked “*”are not stocked since they are seldom
required for routine service. Some delay should be
anticipated when ordering these items.
•When two or more parts are shown in parallel, use the
part described first as the main part.
Confidential
PCG-SRX77/SRX77P (AM)
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.

5-2
Confidential
PCG-SRX77/SRX77P (AM)
Ref.No. Part No. Description Ref.No. Part No. Description
5-1. Main Section
1 1-476-939-21 KEY BOARD UNIT (US)
2 A-8066-903-A ASSY HDD 20GB (H, 15F) (S)
3 1-476-945-11 ENCODER, JOG
4 1-544-951-21 SPEAKER
5 1-796-319-11 PAD, TOUCH
6 1-823-571-11 CABLE, FLEXIBLE FLAT (SWX-TP)
7 1-823-572-11 CABLE, FLEXIBLE FLAT
8 1-823-573-11 CABLE, FLEXIBLE FLAT
9 4-657-941-01 COVER (TP)
10 4-657-944-01 SPRING (R), TORSION
11 4-657-945-01 PLATE (TP)
* 12 4-657-949-01 HOLDER (SP)
13 4-657-950-01 WINDOW (MS)
14 4-657-951-02 LEVER
15 4-659-533-01 PLATE (L), GROUND
16 4-659-534-02 PLATE (R), GROUND
17 4-659-843-02 SHEET (TP)
18 A-8067-041-A COMPLETE PWB IFX-175
19 A-8067-047-A COMPLETE PWB SWX-86
20 X-4624-198-5 HOUSING (PARM REST) ASSY
21 4-657-940-02 ESCUTCHEON (JOG)
22 4-657-943-01 KNOB (LATCH)
23 4-657-952-01 LEVER (LATCH)
24 1-468-624-11 BATTERY, VANADIUM-LITHIUM
25 1-757-756-51 CABLE, COAXIAL(WITHUFLCONNECTOR
26 1-757-756-61 CABLE, COAXIAL(WITHUFLCONNECTOR
27 1-761-380-23 CARD, MODEM
28 1-761-495-11 CARD, WIRELESS LAN
29 1-763-803-11 FAN, DC
30 1-823-569-11 CABLE, FLEXIBLE FLAT
31 1-823-570-11 CABLE, FLEXIBLE FLAT(MBX-CNX2)
32 1-960-827-41 HARNESS (2 PIN)
33 1-961-480-11 HARNESS, RJ-45
34 1-961-483-11 HARNESS (WITH DC JACK)
36 4-657-957-01 ESCUTCHEON (R)
37 4-657-959-01 COVER (BR)
* 38 4-657-963-01 HEAT SINK
* 39 4-657-971-01 BRACKET (K)
* 40 4-657-975-01 HOLDER (HEAT SINK)
41 4-657-984-01 SHEET (MODEM), INSULATING
42 A-8067-039-A COMPLETE PWB CNX-148
43 A-8067-040-A COMPLETE PWB CNX-149
44 A-8067-043-A COMPLETE PWB IFX-177
45 A-8067-044-A COMPLETE PWB IFX-178
46 A-8058-500-A C/P MBX-57 (P800) (S)
47 X-4624-182-1 HOUSING (BOTTOM) ASSY
48 4-635-956-01 SPRING (B), COMPRESSION COIL
49 X-4624-185-1 ESCUTCHEON (L) ASSY
50 1-761-453-11 PWB, FLEXIBLE PRINT (FOR HDD)
* 51 4-657-969-01 BRACKET (HDF)
* 52 4-657-970-01 BRACKET (HDR)
53 4-657-964-01 LID (HDD)
54 4-657-986-01 FOOT
55 4-657-981-01 SHEET (HDD), INSULATING
56 4-657-977-01 FOOT (R), REAR
57 4-657-976-01 FOOT (L), REAR
58 4-657-968-01 FOOT (R)
59 4-646-722-11 BLIND, SCREW
61 4-657-962-01 SPRING (C), TORSION
66 4-659-711-01 SHEET (BOSS)
67 4-659-832-01 SHEET, THERMAL
68 4-659-844-01 SHEET (SCREW)
69 4-659-904-01 SHEET (MPCI)
70 X-4624-183-2 LID (IV) ASSY
71 X-4624-184-2 LID (L) ASSY
72 4-657-990-31 (SRX77)...LABEL (ID)
72 4-657-990-41 (SRX77P)...LABEL (ID)
80 1-794-548-11 CONNECTOR, USB(A)
81 1-793-162-11 JACK, SMALL TYPE
82 1-695-514-21 JACK (SMALL TYPE) 1P
83 4-660-264-01 PLATE (ANT)
84 4-660-234-01 SHEET (HEAT SINK)
85 4-660-233-01 PLATE (HEAT SINK), GROUND
87 4-660-235-01 GASKET (A)
88 4-660-236-01 GASKET (B)
89 4-658-789-02 TAPE (HARNESS)
90 4-660-756-01 SHEET (PULSE)
91 4-657-991-01 SHEET (JOG), INSULATING
92 4-661-037-02 SHEET (LAN), INSULATING
93 4-660-809-01 SHEET (GROUND PLATE R)
94 4-660-808-01 SHEET (GROUND PLATE)
95 4-660-807-01 SHEET (SPEAKER)
96 4-661-076-01 SHEET (PW)
97 4-661-214-01 SHEET (MS), INSULATING
98 4-660-237-01 GASKET (C)
99 4-661-176-01 SHEET (USB)
100 4-661-231-01 CUSHION (KNOB)
101 4-660-238-01 GASKET (D)
102 1-816-204-11 CONNECTOR, PC CARD (EJECTOR)
103 4-660-752-01 TAPE (LCD)
104 4-657-983-01 SHEET (PC CARD), INSULATING
108 4-662-036-01 SHEET (FFC), INSULATING
B1 4-644-492-51 ACE (M2), LOCK
B2 4-645-016-41 ACE (M2) (DIA.4.6), LOCK
B3 4-654-273-11 ACE (M2), LOCK
B4 4-635-301-01 SCREW M3X4
B5 4-644-492-11 ACE (M2), LOCK
B6 4-659-529-01 BOLT
B7 7-621-772-10 SCREW +B 2X4

Confidential
PCG-SRX77/SRX77P (AM)5-3 5-4
49
61
70
57
71
102
104
43
41
54
26
4532
58
44
46
91
28
69
25
33
92
83
89
89
24
M
M
F
F
C
E
A
I
N
D
H
G
G
J
J
P
P
R
R
Q
L
L
K
H
I
A
B
K
C
N
E
D
B
48
66
100
66
88
34
56
58
98
42
40
85
84
27
67
29
38
39
68
37
Supplied
with 47
36
12
95
94
19
18
97
96
12
95
10
17
22
21
11
5
20
15
59
72
13
16
94
9
14
108
7
6
8
4
4
1
54
50
54
52
51
55
87
53
2
3
Supplied with 20
Supplied with 42
81
82
80
B2
B1
B1
B1
B2
B5 B7
B4
B4
B5
B4
B5
B5
B2 B2
B7
B2
B2
47
31
90
B6
B2
B1
B2
B2 B2
B3
B1
B3
B2
B2
B7
B7
23
B2
30
89
103
101
93
Q
99
Supplied
with 46
89

Confidential
PCG-SRX77/SRX77P (AM)
Ref.No. Part No. Description Ref.No. Part No. Description
5-2. LCD Section –Made by TS –
5-5 5-6
(END)
301 1-476-874-11 INVERTER UNIT
302 A-8058-499-A LCD ASSY(S)
303 1-961-376-12 LCD HARNESS
304 4-657-928-02 COVER (L)
305 4-657-929-02 COVER (R)
* 306 4-657-930-02 TILT (L)
* 307 4-657-931-02 TILT (R)
308 4-657-932-02 LATCH
309 4-657-933-01 CLAMP (LCD)
310 X-4624-178-2 HOUSING (BEZEL) ASSY
311 4-646-976-21 CUSHION (LATCH)
312 4-657-985-01 CUSHION (BZ)
313 4-659-342-01 BLIND (LCD), SCREW
314 X-4624-180-2 HOUSING (DISPLAY) ASSY
315 4-660-749-01 GASKET (TILT)
316 4-661-728-02 SHEET (LCD, HARNESS)
B20 4-644-492-51 ACE (M2), LOCK
B21 4-645-016-41 ACE (M2) (DIA.4.6), LOCK
313
310
312
311
301
303
316 315
314
307
309
302
308
306
311
B21
B20
B20
B20
B20
B20
B20
Supplied
with 310
313
B21
205
304
ACCESSORIES
***********
0801 1-476-943-11 ADAPTOR, AC
0802 1-757-562-31 CORD, POWER
803 1-757-026-11 CABLE, VGA
804 1-756-100-41 BATTERY PACK, LITHIUM ION
4-660-339-01 SPECIFICATION SHEET, 2060UA
4-660-341-01 QUICK START, 2060UA
803
Display Adaptor (1)
801
AC adaptor (1)
802
Power cord (1)
804
Battery (1)
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.