Sony VAIO PCG-XG9 User manual

The Sony VAIO PCG-XG9 comes standard with 128MB (two 64MB modules) of
removable memory. It can be expanded to a maximum of 256MB† by installing
the following Viking Components memory options into its two available
expansion slots.
Description Viking P/N
32MB PC100 Memory Module SNY9832, RSNY9832
64MB PC100 Memory Module SNY9864, RSNY9864
128MB PC100 Memory Module SNY91664, RSNY91664
†Requires removal of the standard memory modules.
Caution:
Electro Static Discharge (ESD) can damage electronic components. Before touching the mem-
ory module, ensure that you are discharged of static electricity by touching a grounded metal
object.
INSTALLATION INSTRUCTIONS:
1.Turn the computer off and disconnect the AC power supply and any other cables from
the unit.
Note: If the unit appears to be powered down, ensure that it is not in Suspend
mode.
2. Turn the computer upside down. Remove the battery from the system. If you are not
familiar with this procedure, please refer to your computer’s “Owner’s Manual.”
3. Locate the single hold-
ing screw toward the cen-
ter of the bottom panel.
Remove only this screw
with a small Phillips screw
driver. Then carefully
return the system right
side up and open the dis-
play screen.
4. Locate the two keyboard locking tabs at the base of the keyboard panel. The first tab
is located below the“Fn” key and the second tab is located below the “Home” key. With a
small flat-bladed
screwdriver or a paper
clip, unlock the key-
board panel from the
computer chassis by
sliding both locking
tabs toward the front
of the system.
5. To completely release the
keyboard panel from the
chassis, lift the front of the
keyboard panel up about a
quarter of an inch. Then slide
the keyboard panel forward
about a quarter of an inch.
6. Carefully rotate the front
keyboard panel away from
you and rest it, upside down,
on the display screen.
Caution: Do not disconnect
or place tension on the
cable connecting the key-
board panel to the system
board.
7. Locate the two memory expansion slots
on the left side of the open compartment.
Also locate the off-center key on each of the
slots.Each slot will be occupied with a 64MB
standard memory module. If you wish to
upgrade your system past 128MB, the stan-
dard memory modules will need to be
removed. Proceed to step 8 for instructions
on how to remove a memory module.
Note: The memory expansion slot closest
to the front of the system must always be
occupied with a memory module.
8. To remove a memory module, locate the retaining clips on both sides of the memory
module. Gently pull both clips away from the module, then lift the module out of its
expansion slot.
VIKING COMPONENTS
MEMORY INSTALLATION GUIDE
Manual No. 1005296 • Release 01/2000, Rev. A
SONY®
VAIO PCG-XG9
1

9. To install a memory module, insert the module into an expansion slot at an angle and
then push it down until it clicks into place. To be certain that the module is installed cor-
rectly, ensure that the off-center notch on the module is aligned with the off-center key
of the expansion slot. The module can only be installed one way due to the position of
the notch.
10. Return the keyboard panel back to its original position and be sure both keyboard
locking tabs have been secured. Close the display screen and secure the single holding
screw on the bottom panel of the computer.
11. Insert the battery back into its compartment and turn the system right side up.
12. Replace the AC power supply and any other cables you may have disconnected.
13. Open the display screen and turn the system on. The computer will automatically
reconfigure itself to recognize the additional memory. The new memory can be verified
during the POST routine at start-up and at the SETUP utility.
The installation is now complete.
WARRANTY & DISCLAIMERS:
All Viking Components products have been thoroughly tested free of defects in material
and workmanship. If any malfunction should occur while using one of our products in its
recommended environment, Viking, at its option, will repair or replace the product at no
charge,provided the product or any part thereof has not been abused, misused, neglect-
ed, replaced, repaired or modified. Viking shall make the final determination as to the
existence and the cause of any defect. Viking will not repair or replace products desig-
nated as having a “Limited Lifetime” which fail solely because their estimated life has
expired. No warranty is made with respect to customer products produced to original
purchaser specifications except as specifically stated in writing by Viking.
All shipping costs shall be the responsibility of the purchaser.
Except as provided herein, there are no express or implied warranties of merchantability
or fitness for a particular purpose. Under no circumstances will Viking Components be
liable in any way to the purchaser for any damages, including but not limited to lost rev-
enue,lost wages,or any other incidental or consequential damages arising out of the use
of or inability to use this product. Viking reserves the right to make modifications in both
hardware and software without prior notifications.
All Viking Components products are 100% guaranteed compatible with the OEM
machines for which they are designed. All OEM's names, trademarks and part numbers
are used for identification purposes only, and in no way imply that any of our products
are original equipment parts.
Sony and VAIO are registered trademarks of Sony Corporation.
Product names mentioned herein may be trademarks or registered trademarks of their
respective companies.
Copyright 2000 Viking Components, Inc.
2