Sony BRAVIA KLV-40U100M User manual

SONY KLV-40U100M
S
SE ER RV VI IC CE E M MA AN NU UA AL L
LCD HDTV MONITOR
SONY
THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE
EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE
ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR
CHANGES, ERRORS OR OMISSIONS.

SONY KLV-40U100M
1
Revision List
Version Release Date Revision Instructions TPV Model
A00 Mar.-03-2006 Initial Edition Release EME5LGNKC6SYNMP

SONY KLV-40U100M
2
Table of Content
Revision List ---------------------------------------------------------------------------------------------------------------------------- 01
Table of Content ------------------------------------------------------------------------------------------------------------------------- 02
1.General Specification ---------------------------------------------------------------------------------------------------------------- 03
2.Operations Instructions ------------------------------------------------------------------------------------------------------------- 04
2.1 Remote Control Button Description ------------------------------------------------------------------------------------------- 04
2.2 Unit Controls And Indicators -------------------------------------------------------------------------------------------------- 05
2.3 OSD Operations ------------------------------------------------------------------------------------------------------------------- 05
2.4 Input / Output terminal ----------------------------------------------------------------------------------------------------------- 12
2.5 Connecting The Unit ------------------------------------------------------------------------------------------------------------- 13
3.Input / Output specification ------------------------------------------------------------------------------------------------------- 18
3.1 PC Input Signal Connector ----------------------------------------------------------------------------------------------------- 18
3.2 Signal Timing ---------------------------------------------------------------------------------------------------------------------- 19
4. Disassembly Instructions --------------------------------------------------------------------------------------------------------- 20
5. Repair Flow Chart ------------------------------------------------------------------------------------------------------------------- 24
6. White Balance, Luminance Adjustment -------------------------------------------------------------------------------------- 28
7. BOM List -------------------------------------------------------------------------------------------------------------------------------- 39
8. PCB Layout ---------------------------------------------------------------------------------------------------------------------------- 53
8.1 Main Board ------------------------------------------------------------------------------------------------------------------------- 53
8.2 Power Board ----------------------------------------------------------------------------------------------------------------------- 56
8.3 Key Board --------------------------------------------------------------------------------------------------------------------------- 57
9. Block Diagram ------------------------------------------------------------------------------------------------------------------------ 57
9.1 Main Board ------------------------------------------------------------------------------------------------------------------------- 57
9.2 Power Board ----------------------------------------------------------------------------------------------------------------------- 59
10. Exploded View ---------------------------------------------------------------------------------------------------------------------- 60
11. Schematic Diagram --------------------------------------------------------------------------------------------------------------- 61
11.1 Main Board ------------------------------------------------------------------------------------------------------------------------ 61
11.2 Power Board ---------------------------------------------------------------------------------------------------------------------- 69
11.3 Key Board ------------------------------------------------------------------------------------------------------------------------- 71
11.4 Earphone Board ----------------------------------------------------------------------------------------------------------------- 72
12.Wiring Diagram ----------------------------------------------------------------------------------------------------------------------- 73

SONY KLV-40U100M
3
1. General Specifications
Items Specification
Screen System 40” TFT LCD color Panel
Display Area 885.168 (H) x 497.664 (V)
Number of Pixels 1,366 x 768 Pixel
Pixel Pitch 0.648 (H) x 0.648 (V)
LCD Panel
Display Color 16.7M (8 bit-true)
Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative
S VIDEO (4-pin mini DIN)
C: 0.286 Vp-p (Burst signal), 75 ohms
VIDEO 1 Vp-p, 75 ohms unbalanced, sync negative
VIDEO IN 1/2
(NTSC Video
Standard)
AUDIO 500 mVrms (100% modulation) Impedance: 47 kilohms
Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative
PB: 0.7 Vp-p, 75 ohms
PR: 0.7 Vp-p, 75 ohms
YPBPR(Component Video)
Signal format: 480i, 480p, 720p, 1080i
HD/DVD IN3
AUDIO 500 mVrms (100% modulation) Impedance: 47 kilohms
Video: 480i, 480p, 720p, 1080i
HDMI
A
udio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20
and 24 bits
HDMI IN 4
AUDIO 500 mVrms (100% modulation) Impedance: 47 kilohms
Signal Input D-Sub 15 pin, analog RGB, 0.7 Vp-p, 75ohms, positive
PC IN 5
Audio Input Stereo mini jack, 500m Vrms, 47 kilohms
Headphones Stereo mini jack, Impedance: 16 ohms
Speaker Full range: 4 × 20 cm
Audio Output
Speaker output 10W + 10W
Requirement AC 110-127V, 60Hz
Power
Consumption In use: 242 W, and in standby less than 1W
Dimensions With Stand 989 × 685 × 127 mm
Operating Temp. +0°C ~ + 35°C
Environment
Operating Humidity 10% ~ 85%
Accessories
Rating Label, I-O Label, AC label, AC power cord, VGA cable, Supporting Belt (Include
screw), User manual (US/FR), Quick Start Guide (US/FR), Remote control, Batteries,
Warranty Card, Registration Card, Warranty for Canada.

SONY KLV-40U100M
4
2. Operations Instructions
2.1 Remote Control Description

SONY KLV-40U100M
5
2.2 Unit Controls Indicators
2.3 OSD Operations
Descriptions:
1. Menu panel shall be displayed by pushing the MENU button in the POWER ON condition.
2. Yellow marking on Icon of Menu shall be up or down with the ↑／↓button.
3. Yellow marking on Icon of Main Menu be right or left with the →/ ←button.
4. To choose the item or Menu, push SELECT.
5. By pushing Menu button during Menu appears, Menu panel should be disappears.

SONY KLV-40U100M
6
1. Picture Setting

SONY KLV-40U100M
7
Picture Setting for PC Signal Input
2. Sound Setting

SONY KLV-40U100M
8
3. Screen Setting

SONY KLV-40U100M
9

SONY KLV-40U100M
10
Screen Setting for PC Signal Input

SONY KLV-40U100M
11
4. Setup Setting

SONY KLV-40U100M
12
2.4 Input / Output Terminal
This unit includes several types of video inputs. When connecting your unit, use the inputs that are available on
your devices that provide the best video performance, as described below.

SONY KLV-40U100M
13
2.5 Connecting the unit
(1) To connect a Satellite Receiver
1 Connect the satellite antenna cable to the satellite receiver’s satellite input jack.
2 Use an A/V and S VIDEO cables to connect the satellite receiver’s AUDIO and S VIDEO output jacks to the unit’s
AUDIO and S VIDEO input jacks (VIDEO 1 or 2).
3. Press V1 or V2 on the remote control or Press INPUT on the top panel repeatedly to select the satellite receiver
input (Video 1 or 2).
4. If your satellite receiver is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable.

SONY KLV-40U100M
14
(2) To connect the VCR and cable
1 Connect the CATV cable to the VCR’s VHF/UHF input jack.
2 Use an A/V and S VIDEO cables to connect the VCR’s AUDIO and S VIDEO output jacks to the unit’s AUDIO and
S VIDEO input jacks (VIDEO 1 or 2).
3. Press V1 or V2 on the remote control or Press INPUT on the top panel repeatedly to select the VCR input (VIDEO
1 or 2).
4. If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable.
(3) To connect a HD Equipment
1. Disconnect all power sources before making any connections.
2. Using a component video cable, connect your equipment’s YPBPRoutput jacks to the unit’s YPBPRinput jacks.
Use the HD/DVD IN3 connections.
3. Using the audio cable, connect your equipment’s AUDIO output jacks to the unit’s AUDIO input jacks.
4. Some of the HD equipment you can connect to receive the broadcasting signals are digital cable box, digital
satellite receiver and digital TV receiver.
5. Press V3 on the remote control or Press INPUT on the top panel repeatedly to select the HD equipment input
(Video 3).

SONY KLV-40U100M
15
(4) To connect a DVD player with component video connectors
1. Use a component video cable to connect the DVD player’s YPBPRoutput jacks to the unit’s YPBPRinput jacks.
Use the HD/DVD IN3 connections.
2. The YPBPR jacks on your DVD player are sometimes labeled Y, CB and CR, or Y, B-Y and R-Y. If so, connect
the cables to their matching color jacks.
3. Use an audio cable to connect the DVD player’s AUDIO output jacks to the unit’s AUDIO input jacks (HD/DVD
IN3).
4. Press V3 on the remote control or Press INPUT on the top panel repeatedly to select the DVD player input (Video
3).
(5) To connect a DVD player with S VIDEO and audio connectors
If your DVD player does not have component video (YPBPR) jacks, or the component video inputs are already
connected to another device, use this connection.
1 Use an S VIDEO cable to connect the DVD player’s S VIDEO output jack to the unit’s S VIDEO input jack (VIDEO
1 or 2).
2 Use an audio cable to connect the DVD player’s AUDIO output jacks to the unit’s AUDIO input jacks (VIDEO 1 or
2).
If your DVD player is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable.
(6) To connect HDMI-Equipped Device

SONY KLV-40U100M
16
1. Use an HDMI cable to connect the device’s HDMI output connector to the unit’s HDMI IN connector on the rear
panel.
2. HDMI cables transmit both audio and video signals. (Separate audio cables are not necessary.) You can
purchase HDMI cables at your local electronics store. Do not connect a PC to the unit’s HDMI input. Use the PC IN
(RGB) connector instead when connecting a PC.
3. 3. Press V4 on the remote control or Press INPUT on the top panel repeatedly to select the HDMI-Equipped
device equipment input (Video 4).
(7) To connect a device with DVI-HDTV connector
If the device does not have an HDMI connector, you can connect the unit’s HDMI IN connector to the device’s
DVI-HDTV output connector using a DVI to HDMI adapter or cable.
1 Use a DVI to HDMI adapter or cable to connect the device’s DVIHDTV output connector to the unit’s HDMI IN
connector on the rear panel. The DVI-HDTV VIDEO connector does not provide audio, so audio cables must be
connected to provide sound when a DVI to HDMI adapter or cable is used. Do not connect a PC to the unit’s HDMI
input. Use the PC IN (RGB) connector instead when connecting a PC.
2 Use an Audio cable to connect the device’s AUDIO output jacks to the unit’s AUDIO input jacks on the rear panel.
3. Press V4 on the remote control or Press INPUT on the top panel repeatedly to select the DVI-HDTV-equipped
device input (Video 4).
(8) To connect a PC (personal computer)
If you connect your PC to the unit, you can watch your personal computer’s display on the unit.
When your PC is connected to the unit with the supplied HD15-HD15 cable and optional audio cable, you can view
and listen to the PC’s video and audio output on the unit.
Press V5 on the remote control or Press INPUT on the top panel repeatedly to select the PC input (Video 5).

SONY KLV-40U100M
17
(9) To connect a camcorder or video game equipment
1. Use an A/V and S VIDEO cables to connect the camcorder or video game equipment AUDIO and S VIDEO output
jacks to the unit’s AUDIO and S VIDEO input jacks (VIDEO 1 or 2) on the rear of panel.
2. If your camcorder is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable.
If you have a mono camcorder, connect its audio output jack to the unit’s L MONO audio input jack.
3. Press V1 or V2 on the remote control or Press INPUT on the top panel repeatedly to select the camcorder or
game input (Video 1 or 2).

SONY KLV-40U100M
18
3. Input /Output Specification
3.1 PC Input Signal Connector
Lay the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord
must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical
conduct ground. If the AC outlet in your location does not have provisions for the grounded type plug, the installer
should attach the proper adapter to ensure a safe ground potential.
Connect the 15-pin D-SUB color display shielded signal cable to your signal system device and lock both screws on
the connector to ensure firm grounding. The connector information is as follow:
1
6
11 15
5
10
15 - Pin Color Display Signal Cable
Pin No. Descriptions Pin No. Descriptions
1 Red Video 9 +5V
2 Green Video 10 VGA-CAB
3 Blue Video 11 GROUND
4 TXD 12 SGA-SDA
5 GROUND 13 Horizontal Sync.
6 Red Video Ground 14 Vertical Sync.
7 Green Video Ground 15 VGA-SCL
8 Blue Video Ground
Apply power to the display by turning the power switch to the "ON" position and allow about ten seconds for Panel
warm-up. The Power-On indicator lights "GREEN" when the display is on.
With proper signals feed to the display, a pattern or data should appear on the screen, adjust the brightness and
contrast to the most pleasing display, or press auto-adjust to get the best picture-quality.
This TV (with PC function) has power saving function following the VESA DPMS. Be sure to connect the signal
cable to the PC.
If your TV requires service, it must be returned with the power cord.

SONY KLV-40U100M
19
3.2 Signal Timing
¾Video signal is NTSC 3.58 format (15.7 kHz, 60 Hz) with 7.5% IRE setup.
¾Component signal is 480i, 480p, 1080i and 720p.
¾HDMI signal is VGA, 480i, 480p, 1080i and 720p.
¾Supported PC Input Signals Table:
Resolution
Signal Name Horizontal[Pixel] Vertical[Pixel]
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640 480 31.5 60
640 480 37.9 72
VGA
640 480 37.5 75
DOS TEXT 720 400 31.5 70
800 600 35.2 56
800 600 37.9 60
800 600 46.9 75
800 600 48.1 72
SVGA
848 480 31.0 60
1024 768 48.4 60
1024 768 56.5 70
XGA
1024 768 60.0 75
1280 768 47.4 60
1280 768 47.8 60
1280 768 60.3 75
WXGA
1360 768 47.7 60