Sony KL-37W1U User manual

Models KL-37W1U KL-50W1U KL-50W2U LE-1 chassis
To enter the service mode:
Turn the mains power on while holding the "PROG +" and the "PROG -"
buttons on the set simultaneously.
"TT" will appear at the top right hand corner of the screen
Press "01" on the remote control to see the service menu on screen
Press the "arrow up" and the "arrow down" buttons on the remote
control to navigate the menus
Press the "OK" button to select an adjustment
Press the "arrow up" and the "arrow down" buttons to highlight an
adjustment, and press the "OK" button to allow adjustment.
Use the "arrow up" and the "arrow down" buttons to adjust the value
Press the "OK" button to store
Turn off the power to exit the service mode
Test mode 2 allows entry of TT numbers to perform some functions. The
important numbers for this chassis are given below
TT00 switch the TT mode off
TT08 set the set to shipping condition
TT15 Factory reset values
TT16 User defined reset values
TT16 loads the contents of the NVM when the set was last switched off
TT15 loads the factory defaults. To do this press TT15 followed by
TT16.
----------------------------------------------------------------------
----------
Models : KV25F1U - KV29F1U - KV25F2U - KV29F2U - KV25F3U -
KV29F3U -
KV25X1U - KV29X1U - KV24WX1U - KV28WX1U - KV24WS2U -
KN28WS2U -
KV28WF1U - KV32WF1U - KV29FX11U - BE-3D chassis
KV28DS20U KV28DX20U KV32DS20U KV32DX20U BE-3E chassis
To access the service mode:
Turn the set on and then put into standby

Press the On Screen Display button
Press the "5" button
Press the "VOLUME +" button
Press the "TV" button
Press the "MENU" button on the remote control to bring up the test
screen
Use the joystick on the remote control to navigate the service menu
(< > ^ v keys BE-3E)
Press the right joystick to enter the selected adjustment
Turn off the power to store and exit the service mode
Test mode 2 allows entry of TT numbers to perform some functions. The
important numbers for this chassis are given below
TT00 switch the TT mode off
TT08 set the set to shipping condition
TT24 Set CTV to UK model (PAL I)
TT44 Set all favourite pages to 100
To re-initialise the NV Ram follow the procedure below:
Set the TV to channel 59
Select TT49
Switch off at the mains supply, wait for one minute and switch the
set back on
Select channel 59, and enter the service mode
Select TT24, (UK destination)
Select TT42, (general reset)
Switch off at the mains, wait for one minute and switch on again
Auto tune the channels and carry out a complete adjustment on the set
----------------------------------------------------------------------
----------
Models KP-41S3U RE-1 chassis
To access the service mode:
Turn the set on and then put into standby
Press the On Screen Display button
Press the "5" button
Press the "VOLUME +" button
Press the "TV" button

Use buttons "1" and "4" on the remote control to navigate the service
menu
Use buttons "3" and "6" to adjust the selected data
Press the "MUTE" button and then the "0" button to store the data
Press the "5" button and then the "0" button to initialise the set.
(Note, this is an extreme measure and should be used with caution!)
Turn the set off to exit
----------------------------------------------------------------------
----------
Models KP-41S3U RE-1 chassis
To access the service mode:
Turn the set on and then put into standby
Press the On Screen Display button
Press the "5" button
Press the "VOLUME +" button
Press the "TV" button
Use buttons "1" and "4" on the remote control to navigate the service
menu
Use buttons "3" and "6" to adjust the selected data
Press the "MUTE" button and then the "0" button to store the data
Press the "5" button and then the "0" button to initialise the set.
(Note, this is an extreme measure and should be used with caution!)
Turn the set off to exit
----------------------------------------------------------------------
----------
Models KP-41DS1U RE-2D chassis
To access the service mode:
Turn the set on and then put into standby
Press the On Screen Display button
Press the "5" button
Press the "VOLUME +" button
Press the "TV" button
Use the JOYSTICK Up / Down on the remote control to navigate the
service menu
Move the JOYSTICK to the right > to enter the selected adjustment

Press OK on the JOYSTICK to EXIT
Press the "MUTE" button and then the "0" button to write data
Press the "On Screen Display" button to copy data
Turn the set off to quit the service mode when adjustments are
complete
----------------------------------------------------------------------
----------
Models KV-14V4U TE-1 chassis
To access the service mode:
Turn the set on and then put into standby
Press the On Screen Display button
Press the "5" button
Press the "VOLUME +" button
Press the "TV" button
Use buttons "1" and "4" on the remote control to navigate the service
menu
Use buttons "3" and "6" to adjust the selected data
Turn off the power to store and exit the service mode
The codes on screen are as follows:
ODL Power On Delay
OSH On screen H-position
MUT FTZ muting on *Do not adjust
VAM V. size
VBC V breath correct *Do not adjust
PAM Parabola amp. *Do not adjust
PTI Parabola tilt *Do not adjust
VLI V-linearity
CCR Corner correction *Do not adjust
HAM V. cent *Do not adjust
BIN Blue intensity
GIN Green intensity
RIN Red intensity
CLS Colour system
SCO Sub contrast
SBR Sub brightness

SSA Sub saturation
SHU Sub hue
SSH Sub sharpness
G2 adj G2 adjustment
32K adj
----------------------------------------------------------------------
----------
Models KV-16WS1U KV-21X1U KV-21X4U KV-20WS1U BE-5 chassis
To access the service mode:
Turn the set on and then put into standby
Press the On Screen Display button
Press the "5" button
Press the "VOLUME +" button
Press the "TV" button
Press the "MENU" button on the remote control to see the service menu
on screen
Use the "blue" button and the "green" button on the remote control to
navigate the service menu
Use the "Yellow" button and the "red" button to adjust the selected
data
Turn the set off to exit and store
Test mode 2 allows entry of TT numbers to perform some functions. The
important numbers for this chassis are given below
TT00 switch the TT mode off
TT08 set the set to shipping condition
TT26 Set CTV to UK model (PAL I)
TT41 Re-initialise NVM
TT43 Re-initialise geometry settings
Note: For TT numbers above 41, the channel number needs to be 59
----------------------------------------------------------------------
----------
Models. KV-32WS4U KV32WX4U KV32WX2U AE-4 chassis
To enter the service mode:
Turn the mains power on while holding the "PROG +" and the "PROG -"

buttons on the set simultaneously.
"TT" will appear on the top right hand corner of the screen.
Press "MENU" on the remote control to get the service menu on screen
Navigate the menu by moving the joystick up and down.(green and blue)
Press the joystick down to select an adjustment.
Turn TV off to exit service mode
Test mode 2 allows entry of TT numbers to perform some functions. The
important numbers for this chassis are given below
TT00,10,20,30,40 pressing these numbers will switch the TT mode
off
TT01 switch service menu on
TT08 set the set to shipping condition
TT21 picture rotation automatic function
TT25 Status menu display
TT49 New initialisation
----------------------------------------------------------------------
----------
Models. KV28FD1E KV28FD1K KV32FD1E KV32FD1K GE-1 chassis
To enter the service mode:
Turn the mains power on while holding the "PROG +" and the "PROG -"
buttons on the set simultaneously.
"TT" will appear on the top right hand corner of the screen.
Press "MENU" on the remote control to get the service menu on screen
Navigate the menu by moving the joystick up and down.(green and blue)
Press the joystick down to select an adjustment.
Turn TV off to exit service mode
The main adjustments are:
MCP CXA2101 - picture (colour, drives, brightness etc)
Deflection control SDA9361 - geometry
----------------------------------------------------------------------
----------

Models KV-29X5U FE-1 chassis
To access the service mode:
Turn the set on and then put into standby
Press the On Screen Display button
Press the "5" button
Press the "VOLUME +" button
Press the "TV" button
Use buttons "^"(Green) and "v"(Blue) on the remote control to
navigate the service menu
Press YELLOW button to enter required menu
Use buttons "<" and ">" to adjust the selected data
Press the "MENU" button to store the data and exit
Test Menu
Picture - (RGB. Drives & Cut offs, Sub Colour, Sub brightness)
Geometry - (Vert. and Horiz. adjustments)
Sound - (NICAM Information)
TV Status - (Destination and Country info.)
AGC. Adjust
Technical
----------------------------------------------------------------------
----------