Sony KV-32S42 User manual

TRINITRON®COLOR TV
MODEL DEST.COMMANDER CHASSISNO.
KV-32S42 US RM-Y168 SCC-S07U-A
KV-32S42 CND RM-Y168 SCC-S08R-A
KV-32S66 US RM-Y169 SCC-S07V-A
KV-32S66 CND RM-Y169 SCC-S08S-A
KV-32V42 US RM-Y168 SCC-S07W-A
KV-35S42 US RM-Y168 SCC-S07R-A
KV-35S42 CND RM-Y168 SCC-S07P-A
KV-35S66 US RM-Y169 SCC-S07S-A
KV-35S66 CND RM-Y169 SCC-S08Q-A
KV-35V42 US RM-Y168 SCC-S07T-A
SERVICE MANUAL
CHASSIS
AA-2D
RM-Y168
KV-35V42
873 Front.p65 7/9/99, 5:15 PM1

—2 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
SPECIFICATIONS
1) 1Vp-p75ohmsunbalanced,syncnegative
2) Y: 1Vp-p75ohmsunbalanced,syncnegative
C: 0.286Vp-p(Burst signal), 75ohms
3) 500mVrms(100% modulation), Impedance: 47 kilohms
4) Morethan 408 mVrmsat the maximumvolume setting (variable)
Morethan 408 mVrms (fix)
Impedance(output):2kilohms
( •)SRS (SOUND RETRIEVAL SYSTEM)
The ( •)SRS (SOUND RETRIEVAL SYSTEM) is
manufactured by Sony Corporation under license
from SRS Labs, Inc. It is covered by U.S. Patent No.
4,748,669. Other U.S. and foreign patents pending.
The word ‘SRS’ and the SRS symbol ( •) are
registered trademarks of SRS Labs, Inc.
BBE and BBE symbol are trademarks of BBE Sound,
Inc. and are licensed by BBE Sound, Inc. under U.S.
Patent No. 4,638,258 and 4,482,866.
Television system
American TV standard, NTSC
Channel coverage
VHF:2-13/UHF:14-69/CATV:1-125
Picture tube
Trinitron® tube
Visible screen size
32-inch picture measured diagonally
(KV-32S42/32S66/32V42)
35-inch picture measured diagonally
(KV-35S42/35S66/35V42)
Actual screen size
34-inch picture measured
(KV-32S42/32S66/32V42)
37-inch picture measured
(KV-35S42/35S66/35V42)
Antenna
75 ohm external terminal for VHF/UHF
Supplied Accessories
RM-Y168 (KV-32S42/32V42/35S42/35V42)
RM-Y169 (KV-32S66/35S66)
Batteries size AA (R6) (2)
Optional Assessories
A/V Cable VMC-810/820/830HG
Audio Cable RKC-515HG
S-Link Cable RK-G69HG
S Video Cable YC-15/30HG
TV Stand SU-32A4, SU-35A4
Design and specifications are subject to change without notice.
KV-32S42 KV-32S66 KV-32V42 KV-35S42 KV-35S66 KV-35V42
Power requirements 120V,60Hz 120V,60Hz 120V,60Hz 120V,60Hz 120V,60Hz 120V,60Hz
Video
1)
12 223
S Video
2)
11 112
Audio
3)
12 223
Audio Out
4)
11 111
Monitor Out --1--1
S-Link -3--3-
Speaker output(W) 5W x 2 5W x 2 5W x 2 5W x 2 5W x 2 5W x 2
Power Consumption(W)
In use(Max)
180W 180W 180W 210W 210W 210W
In standby 2W 2W 2W 2W 2W 2W
Dimensions(W/H/D)
(mm) 791 x 707 x 604.5mm 791 x 707 x 604.5mm 821 x 675.3 x 587 mm 870 x 761x 653 mm 870 x 761x 653 mm 920 x 730.8x 641.8 mm
(in) 31 x 27 13/16 x 23 3/4 in 31 x 27 13/16 x 23 3/4 in 34 1/4 x 30 x 25 5/8 in 34 1/4 x 30 x 25 5/8 in 3
Mass (kg) 65 kg 65 kg 70 kg 83 kg 83 kg 90 kg
(lbs) 143 lbs 143 lbs 154 lbs 183 lbs 183 lbs 203 lbs
3
1
3
1

—3 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
Safety Check-Out ........................................................................ 4
1. GENERAL
Connecting and Installing the TV ........................................... 5
Operating Video Equipment ................................................... 7
Operating a Cable Box or Satellite Receiver ........................ 8
Troubleshooting ..................................................................... 8
2. DISASSEMBLY
2-1. Rear Cover Removal ..................................................... 9
2-2. Chassis Assembly Removal......................................... 9
2-3. Service Position ........................................................... 10
2-4. Control Switch Removal.............................................. 10
2-5-1. Picture Tube Removal (32")..................................... 11
2-5-2. Picture Tube Removal (35")..................................... 11
3. SET-UP ADJUSTMENTS
3-1. Beam Landing.............................................................. 12
3-2. Convergence ............................................................... 13
3-3. Focus ........................................................................... 14
3-4. Screen (G2) ................................................................. 14
3-5. White Balance Adjustments......................................... 14
4. SAFETY RELATED ADJUSTMENTS
4-1.R530, R531 Confirmation Method ........................... 15
(Hold-down Confirmation and Readjustments)
4-2. B+Voltage and Confirmation Method ........................... 15
5. CIRCUIT ADJUSTMENTS.................................................. 16
TABLE OF CONTENTS
6. DIAGRAMS
6-1. Block Diagram (KV-32S42/35S42 ONLY)................... 23
6-2. Block Diagram ............................................................. 27
(KV-32S66/32V42/35S66/35V42 ONLY)
6-3. Circuit Boards Location ................................................ 34
6-4. Printed Wiring Boards and Schematic Diagrams ....... 34
• A Board..................................................................... 35
• AV Board................................................................... 48
• B Board..................................................................... 48
• C Board .................................................................... 51
• G Board .................................................................... 52
• HV Board .................................................................. 55
• HS Board .................................................................. 55
• P Board..................................................................... 56
• WB Board ................................................................. 57
• WA Board.................................................................. 58
• UV Board .................................................................. 59
6-5. Semiconductors .......................................................... 63
7. EXPLODED VlEWS
7-1. Chassis (KV-32S42 ONLY) ......................................... 64
7-2. Chassis (KV-32S66 ONLY) ......................................... 65
7-3. Chassis (KV-32V42 ONLY) ......................................... 66
7-4. Chassis (KV-35S42 ONLY) ......................................... 67
7-5. Chassis (KV-35S66 ONLY) ......................................... 68
7-6. Chassis (KV-35V42 ONLY) ......................................... 69
8. ELECTRICAL PARTS LIST
• Table of Contents for Parts List ....................................... 70
• Parts Listings.................................................................... 71
WARNINGS AND CAUTIONS
Section Title Page Section Title Page
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE
AND THE ANODE CAP TO THE METAL CHASSIS, CRT
SHIELD, OR CARBON PAINTED ON THE CRT, AFTER
REMOVING THE ANODE.
WARNING!!
AN ISOLATION TRANSFORMER SHOULD BE USED
DURING ANY SERVICE TO AVOID POSSIBLE SHOCK
HAZARD, BECAUSE OF LIVE CHASSIS. THE CHASSIS
OFTHISRECEIVER ISDIRECTLY CONNECTEDTOTHE
AC POWER LINE.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
ONTHE SCHEMATIC DIAGRAMS, EXPLODEDVIEWS,
AND IN THE PARTS LIST ARE CRITICAL FOR SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARECRITICAL FORSAFEOPERATIONAREIDENTIFIED
IN THIS MANUAL. FOLLOW THESE PROCEDURES
WHENEVERCRITICALCOMPONENTS AREREPLACED
OR IMPROPER OPERATION IS SUSPECTED.
ATTENTION!!
APRESAVOIR DECONNECTELE CAPDE L'ANODE,COURT-CIRCUITER
L'ANODE DU TUBE CATHODIQUE ET CELUI DE L'ANODE DU CAP AU
CHASSISMETALLIQUE DEL'APPAREIL,OU AUCOUCHE DECARBONE
PEINTE SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE
CATHODIQUE.
ATTENTION!!
AFIN D'EVITER TOUT RESQUE D'ELECTROCUTION PROVENANT D'UN
CHÁSSIS SOUS TENSION, UN TRANSFORMATEUR D'ISOLEMENT DOIT
ETRE UTILISÉ LORS DE TOUT DÉPANNAGE. LE CHÁSSIS DE CE
RÉCEPTEUR EST DIRECTEMENT RACCORDÉ À L'ALIMENTATION
SECTEUR.
ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!
LESCOMPOSANTS IDENTIFIESPARUNETRAME ETPARUNEMARQUE
SUR LES SCHEMAS DE PRINCIPE, LES VUES EXPLOSEES ET LES
LISTES DE PIECES SONT D'UNEIMPORTANCE CRITIQUE POUR LA
SECURITEDU FONCTIONNEMENT.NELESREMPLACERQUE PAR DES
COMPOSANTSSONY DONTLE NUMERODE PIECEEST INDIQUEDANS
LE PRESENT MANUEL OU DANS DES SUPPLEMENTS PUBLIES PAR
SONY. LES REGLAGES DE CIRCUIT DONT L'IMPORTANCE EST CRI-
TIQUE POUR LA SECURITE DU FONCTIONNEMENT SONT IDENTIFIES
DANS LE PRESENT MANUEL. SUIVRE CES PROCEDURES LORS DE
CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU
LORSQU'UN MAUVAIS FONTIONNEMENT SUSPECTE.

—4 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
SAFETY CHECK-OUT
After correcting the original service problem, perform the
following safety checks before releasing the set to the
customer:
1. Check the area of your repair for unsoldered or
poorly soldered connections. Check the entire board
surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires
are “pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground
straps, and mounting hardware have been replaced.
Be absolutely certain that you have replaced all the
insulators.
4. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.
Point them out to the customer and recommend their
replacement.
5. Look for parts which, though functioning, show
obvious signs of deterioration.Point them out to the
customer and recommend their replacement.
6. Check the line cords for cracks and abrasion.
Recommend the replacement of any such line cord
to the customer.
7. Check the B+ and HV to see if they are specified
values. Make sure your instruments are accurate;
be suspicious of your HV meter if sets always have
low HV.
8. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for
AC leakage. Check leakage as described below.
Leakage Test
The AC leakage from any exposed metal part to earth
ground and from all exposed metal parts to any exposed
metal part having a return to chassis, must not exceed 0.5
mA(500 microamperes). Leakage currentcan be measured
by any one of three methods.
1. A commercial leakage tester, such as the Simpson
229 or RCA WT-540A. Follow the manufacturers'
instructions to use these instructions.
2. A battery-operated AC milliammeter.The Data
Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by
means of a VOM or battery-operated AC voltmeter.
The “limit” indication is 0.75V, so analog meters must
have an accurate low voltage scale.The Simpson’s
250 and Sanwa SH-63Trd are examples of passive
VOMs that are suitable. Nearly all battery-operated
digital multimeters that have a 2VAC range are
suitable (see Figure A).
How to Find a Good Earth Ground
A cold-water pipe is a guaranteed earth ground. The cover-
plate retaining screw on most AC outlet boxes is also at earth
ground. If the retaining screw is to be used as your earth
ground, verify that it is at ground by measuring the resistance
between it and a cold-water pipe with an ohmmeter. The
reading should be zero ohms. If a cold-water pipe is not
accessible, connect a 60- to 100-watt trouble- light (not a neon
lamp) between the hot side of the receptacle and the retaining
screw. Try both slots, if necessary, to locate the hot side on the
line; the lamp should light at normal brilliance if the screw is at
ground potential (see Figure B).
Figure B. Checking for earth ground.Figure A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µF AC
Voltmete
r
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Trouble Light
AC Outlet Box Ohmmeter
Cold-water Pipe

—5 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
SECTION 1 GENERAL
The instructions mentioned here are partial abstracts from the Operating Instruction Manual.The page numbers shown reflect those of the Operating Instruction Manual.
1
Thank you for purchasing the Sony Trinitron®Color TV. Before reading, check
the model number located on the front of this manual. The menus and illustrations used in these instructions are for KV-35S66. Differences in operation or features will be indicated in the text, for example, “KV-35S66 only.”
This manual is divided into five major sections. We recommend that you review the contents before you begin to use your new TV.
1Connecting and Installing the TV
This section guides you through your initial set up. It shows how to connect to your antenna or cable, and connect any accessories.
2Basic Set Up
This section teaches you the basic skills needed to operate your new TV.
3Using your New TV
This section shows the initial setup screen and how to use your remote control.
4Using your Menus
This section teaches you how to access on-screen menus and adjust your TV's settings.
5Troubleshooting
This section helps you to correct problems you may encounter with your TV.
Safety • Operate the TV only with 120 V AC . • The plug is designed, for safety purposes,
to fit in the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.
• If any liquid or solid object should fall
inside the cabinet, unplug the TV immediately and have it checked by qualified personnel before operating it further.
Installing • To prevent internal heat build-up, do not
block the ventilation openings.
• Do not install the TV in a hot or humid
place, or in a place subject to excessive dust or mechanical vibration.
• The AC power cord is attached to the rear
of the TV with hooks. Do not attempt to remove the cord from these hooks. Doing so could cause damage to the TV.
Using This ManualWelcome! Precautions
Model Number
PICTURE IN
PICTURE (PIP)
SURROUND
AUTO VOLUME
CONTROL
KV-32S42 KV-32S66 KV-32V42 KV-35S42 KV-35S66 KV-35V42
SRS
2
Cable or antenna only 3 Cable and antenna 3 Cable box 4 Cable box and cable to view scrambled channels 4 VCR and cable or antenna 5 VCR and cable box 5 Two VCRs for tape editing 6 Satellite Receiver 7 VCR and Satellite Receiver 7 DVD Player 8 Audio system 9 Camcorder to view tapes 9 VCR using S-Link 10 Satellite Receiver using S-Link 10
Connecting and Installing the TV
Refer to the table below, it will direct you to the diagram suitable to the equipment you will be connecting.
If you will be connecting See page
Making Connections
3
A
• VHF only
or
• VHF/UHF
or
• Cable
B
• VHF only
or
• UHF only
or
• VHF/UHF
C
• VHF
and
• UHF
Antenna connector
(Rear of TV)
VHF/UHF
300-ohm twin lead cable
(Rear of TV)
VHF/UHF
75-ohm coaxial cable
75-ohm coaxial cable
300-ohm twin lead cable
(Rear of TV)
VHF/UHF
EAC-66 U/V mixer (not supplied)
Cable and antenna KV-32S66, 35S66 only If your cable provider does not feature local channels, you may find this set up convenient. Select CABLE or antenna (ANT) mode by pressing ANT on the remote control. Note In order to receive channels with an antenna, you will need to turn your CABLE to OFF and perform the AUTO PROGRAM function, (see page 23).
(Rear of TV)
AUX
VHF/UHF
TO CONVERTER
(No connection "TO CONVERTER" in this case)
CATV cable
Antenna cable
Cable or Antenna Connections Connecting directly to cable or an antenna The connection you choose will depend on the cable found in your home. Newer homes will be equipped with standard coaxial cable (see A
); older homes will probably have 300-ohm
twin lead cable (see
B
); still other homes may
contain both (see
C
).
4
Connecting and Installing the TV (continued)
Cable Box Connections Some pay cable TV systems use scrambled or encoded signals that require a cable box to view all channels. Cable box 1Connect the coaxial connector from your
cable to the IN on your cable box.
2Using a coaxial cable, connect OUT on
your cable box to VHF/UHF on your TV.
Cable box and cable KV-32S66, 35S66 only For this set up, you can switch between scrambled channels (through your cable box), and normal (CATV) channels by pressing ANT on your remote control. Notes • Your Sony remote control can be
programmed to operate your cable box, (see page 30).
• When using PIP, you cannot view the
AUX input in the window picture.
Tip z Pressing ANT switches between these inputs.
TO CONVERTER
Cable box
VHF/UHF
(Rear of TV)
AUX
75-ohm coaxial cable (not supplied)
CATV cable (unscrambled channels)
(signal)
If you are connecting a cable box through the AUX input and would like to switch between the AUX and normal (CATV) input you should consider using the CHANNEL FIX feature, (see page 23).
Cable box
Cable
OUT
IN
(Rear of TV)
VHF/UHF
If you will be controlling all channel selection through your cable box, you should consider using the CHANNEL FIX feature, (see page 23).
OUT
IN

—6 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
5
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUX
TO
CONVERTER
VHF/UHF
AUDIO R AUDIO L VIDEO
LINE
OUT
OUT
IN
S VIDEO
Coaxial cable
(Rear of TV)
Cable/
antenna
VCR
3
1
2
AUDIO-R (red) AUDIO-L (white) VIDEO (yellow)
VCR Connections Connecting an antenna/cable TV system with a VCR 1
Attach the coaxial connector from your cable or antenna to IN on your VCR.
2
Using A/V connectors, connect AUDIO and VIDEO OUT on your VCR to AUDIO and VIDEO IN on your TV.
3
Using a coaxial connector, connect OUT on your VCR to VHF/UHF on your TV.
Tip z
If you are connecting a monaural VCR, connect only the single white audio output to the left input on your TV. Connecting a VCR and TV with a cable box 1
Connect the coaxial cable from the wall to IN on your cable box .
2
Using a coaxial connector, connect OUT on your cable box to IN on your VCR.
3
Connect a coaxial cable (not supplied) from the OUT jack on your VCR to VHF/UHF on your TV.
4
Using A/V connectors, connect AUDIO and VIDEO OUT on your VCR to AUDIO and VIDEO IN on your TV.
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUX
TO
CONVERTER
VHF/UHF
AUDIO R AUDIO L VIDEO
LINE
OUT
OUT
IN
OUT
IN
S VIDEO
(Rear of TV)
Cable box
4
AUDIO-R (red) AUDIO-L (white) VIDEO (yellow)
VCR
Cable
Coaxial cable
2
1
For optimum picture quality, use S VIDEO instead of the yellow A/V cable. S VIDEO does not provide sound, your audio connectors must still be connected.
3
6
Connecting two VCRs for tape editing KV-32V42, 35V42 only MONITOR OUT gives you the ability to use a second VCR to record a program being played by the primary VCR or to perform tape editing and dubbing. 1
Connect the VCR intended for playback using the connection instructions on page 5 of this manual.
2
Using A/V connectors, connect AUDIO and VIDEO IN on your VCR intended for recording to MONITOR AUDIO and VIDEO OUT on your TV.
Connecting and Installing the TV (continued)
IN
13
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
OUT
AUDIO
MONITOR
VAR/FIX
LINE OUT
OUT
IN LINE
IN
OUT
IN
AUDIO R AUDIO L VIDEO AUDIO R AUDIO L VIDEO
VCR (for playback) VCR (for recording)
(Rear of KV-35V42)
12
AUDIO-R (red) AUDIO-L (white) VIDEO (yellow)
To perform tape editing; set the TV to the video input intended for playback by pressing TV/VIDEO.
7
Satellite Receiver Connections Connecting a satellite receiver 1
Connect the cable from your satellite antenna to SATELLITE IN on your receiver.
2
Attach the coaxial connector from your cable or antenna to VHF/UHF on your TV.
3
Using A/V connectors, connect AUDIO and VIDEO OUT on your receiver to AUDIO and VIDEO IN on your TV.
Connecting a satellite receiver and a VCR 1
Connect the cable from your satellite antenna to SATELLITE IN on your receiver
.
2
Attach the coaxial connector from your cable or antenna to IN on your VCR.
3
Using a coaxial connector, connect OUT on your VCR to VHF/UHF on your TV.
4
Using A/V connectors, connect AUDIO and VIDEO OUT on your receiver to AUDIO and VIDEO IN on your VCR.
5
Using A/V connectors, connect AUDIO and VIDEO OUT on your VCR to AUDIO and VIDEO IN on your TV.
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUX
TO
CONVERTER
VHF/UHF
AUDIO R AUDIO L VIDEO AUDIO R AUDIO L VIDEO
SATELLITE IN
VHF/UHF
S VIDEO
OUT
IN
LINE OUT
LINE IN
VHF/UHF
OUT
IN
LINE OUT
12
3
4
5
(Rear of TV)
Satellite receiver
VCR
AUDIO-R (red) AUDIO-L (white) VIDEO (yellow)
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUX
TO
CONVERTER
VHF/UHF
VHF/UHF
OUT
IN
LINE OUT
SATELLITE IN
AUDIO R AUDIO L VIDEO
S VIDEO
Satellite receiver
(Rear of TV)
Satellite antenna cable
1
3
2
AUDIO-R (red) AUDIO-L (white) VIDEO (yellow)
For optimum picture quality, use S VIDEO instead of the yellow A/V cable. S Video does not provide sound, your audio connectors must still be connected.
Pressing TV/VIDEO on the remote control will allow you to view from the satellite receiver or VCR.
8
DVD Player Connections Connecting a DVD Player 1
Using audio connectors, connect AUDIO OUT on your DVD player to AUDIO IN on your TV.
2
Using an S VIDEO cable, connect S VIDEO on your DVD player to S VIDEO on your TV.
Note If you do not have an S Video cable, connect a yellow video cable from LINE OUT VIDEO on your DVD to VIDEO IN on your TV.
Connecting and Installing the TV (continued)
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUDIO R AUDIO L VIDEO
S VIDEO
LINE OUT
1
(Rear of DVD player)
AUDIO-R (red) AUDIO-L (white)
(Rear of TV)
S VIDEO cable
2

—7 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
9
Additional Connections Connecting an audio system For an enhanced sound, connect your audio system to your TV. 1
Using AUDIO connectors, connect AUDIO OUT on your TV to one of the unused Line inputs (e.g. Tape-2, AUX1, etc.) on your stereo.
2
Set your stereo to the chosen Line input and use the AUDIO menu to set your
audio output, (see page 19).
Connecting a camcorder This connection is convenient for viewing a picture directly from your camcorder. Using A/V connectors, connect AUDIO and VIDEO OUT on your camcorder to AUDIO and VIDEO IN on your TV. Connection can also be made directly to the A/V input located on the the rear of the TV. Tip z If you are connecting a monaural camcorder, connect only the single white audio output to the left input on your TV.
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUDIO OUT
(VAR/FIX)
S-LINK
L
R
S-LINK
HRD
Line input
AUDIO-R (red)
AUDIO-L (white)
(Rear of TV)
1
2
VIDEO 2 INPUT
VIDEO L
(MONO)
-AUDIO-R
A/V output
AUDIO-R (red)
AUDIO-L (white)
VIDEO (yellow)
(Front of KV-32V42, 35V42 only)
10
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUDIO OUT
(VAR/FIX)
S-LINK
L
R
S-LINK
OUT
IN
LINE
OUT
AUDIO R AUDIO L VIDEO
S-LINK
Using Special Sony Features KV-32S66, 35S66 only Connecting S-Link to a VCR S-Link automatically powers on the TV and switches to the correct video input when a tape is inserted in the VCR. 1
Using A/V connectors, connect AUDIO and VIDEO OUT on your VCR to AUDIO and VIDEO IN on your TV.
2
Using an S-Link connector (mono mini plug), connect S-LINK on your VCR to S-LINK/CONTROL S-OUT in the same VIDEO IN column on your TV.
Connecting S-Link to a satellite receiver When you power on the satellite receiver , S-Link automatically powers on the TV and switches to the correct video input. 1
Using A/V connectors, connect AUDIO and VIDEO OUT on your satellite receiver to AUDIO and VIDEO IN on your TV.
2
Using an S-Link connector (mono mini plug), connect S-LINK on your satellite receiver to S- LINK/CONTROL S-OUT in the same VIDEO IN column on your TV.
Note The S-Link feature will override the “SKIP” VIDEO LABEL input, (see page 21).
2
1
(Rear of TV)
VCR
AUDIO-R (red)
AUDIO-L (white)
VIDEO (yellow)
IN
12
(MONO)
VIDEO
S VIDEO
AUDIO
L
R
AUDIO OUT
(VAR/FIX)
S-LINK
L
R
S-LINK
VHF/UHF
OUT
IN
LINE
OUT
SATELLITE IN
AUDIO R AUDIO L VIDEO
S-LINK
2
AUDIO-R (red) AUDIO-L (white) VIDEO (yellow)
1
(Rear of TV)
Satellite receiver
The S-Link connector must be in the same VIDEO-IN column as the connected A/V cables.
Connecting and Installing the TV (continued)
28
Programming the remote You can use the supplied remote control to operate Sony or non-Sony video equipment.
Operating Video Equipment
1
Press CODE SET.
2
Press VTR/DVD (FUNCTION).
3
Use the 0-9 buttons to key in the manufacturer's code number from the following chart.
4
Press ENTER.
VCR code numbers Manufacturer Code Sony 301, 302, 303 Admiral (M. Ward) 327 Aiwa 338, 344 Audio Dynamic 314, 337 Broksonic 319, 317 Canon 309, 308 Citizen 332 Craig 302, 332 Criterion 315 Curtis Mathes 304, 338, 309 Daewoo 341, 312, 309 DBX 314, 336, 337 Dimensia 304 Emerson 319, 320, 316, 317, 318, 341 Fisher 330, 335 Funai 338 General Electric 329, 304, 309 Go Video 322, 339, 340 Goldstar 332
Hitachi 306, 304, 305,338 Instant Replay 309, 308 JC Penney 309, 305, 304, 330, 314, 336, 337 JVC 314, 336, 337, 345, 346, 347 Kenwood 314, 336, 332, 337 LXI (Sears) 332, 305, 330, 335, 338 Magnavox 308, 309, 310 Marantz 314, 336, 337 Marta 332 Memorex 309, 335 Minolta 305, 304 Mitsubishi/MGA 323, 324, 325, 326 Multitech 325, 338, 321 NEC 314, 336, 337 Olympic 309, 308 Optimus 327 Panasonic 308, 309, 306, 307 Pentax 305, 304 Philco 308, 309 Philips 308, 309, 310 Pioneer 308 Quasar 308, 309, 306 RCA/PROSCAN 304, 305, 308, 309, 311,
312, 313, 310, 329
Realistic 309, 330, 328, 335, 324, 338 Sansui 314 Samsung 322, 313, 321 Sanyo 330, 335 Scott 312, 313, 321, 335, 323, 324, 325, 326 Sharp 327, 328 Shintom 315 Signature 2000 (M. Ward) 338, 327 SV2000 338 Sylvania 308, 309, 338, 310 Symphonic 338 Tashiro 332 Tatung 314, 336, 337
Teac 314. 336, 338, 337 Technics 309, 308 Toshiba 312, 311 Wards 327, 328, 335, 331, 332 Yamaha 314, 330, 336, 337 Zenith 331
Operating a VCR To turn on or off To select a channel directly To change channels To record To play To stop To fast forward To rewind the tape To pause To scan To change input mode
Buttons on the remote control Press VTR/DVD (POWER). Press the 0-9 buttons.
Press CH +/–. Press (and r
simultaneously. Press (.
Press p. Press ).
Press 0.
Press P. To resume normal playback, press again or press (. Press )or 0during
playback. To resume normal playback, release the button. Press TV/VTR.
29
Laserdisc code numbers Manufacturer Code Sony 701 Panasonic 704, 710 Pioneer 702 Operating a Laserdisc To turn on or off To play To stop To pause To scan To search the chapter forward or backward Tip z If you will not be programming a satellite receiver or cable box into the SAT/CABLE function of your remote, you can use it to program other video equipment (e.g. DVD, MDP, or second VCR).
DVD (Digital Versatile Disc) code numbers Manufacturer Code Sony 751 Panasonic 753 Pioneer 752 RCA 755 Toshiba 754 Operating a DVD player To turn on or off To play To stop To pause To scan To search the chapter forward or backward To select chapters directly MENU To move cursor in menu
Buttons on the remote control Press VTR/DVD (POWER). Press (. Press p. PressP. To resume normal playback, press again or press (.
Press )or 0during
playback. To resume normal playback, press (. Press CH +/–.
0-9 + ENTER.
Press to display DVD menu. Use your arrow buttons V,v,B,b.
Buttons on the remote control Press VTR/DVD (POWER). Press (. Press p. PressP. To resume normal playback, press again or press (. Press )or 0during playback. To resume normal playback, press (. Press CH +/–.
Tips z • In some rare cases, you may not be able to operate
your non-Sony video equipment with the supplied remote control. In this case, please use the equipment’s own remote control.
• When you remove the batteries, the code number may
revert to the factory setting.
• The code numbers for Sony VCRs are assigned at the
factory as follows:
VHS VCR 301
(preset code for the
supplied remote control)
8 mm VCR 302 Beta, ED Beta VCRs 303

—8 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
30
Manufacturer
Hamlin/Regal
Jerrold/G. I.
Oak Panasonic Pioneer Scientific Atlanta Tocom Zenith
Programming the remote control You can program the supplied remote control to operate a cable box or satellite receiver. 1
Press CODE SET.
2
Press SAT/CABLE (FUNCTION).
3
Use the 0-9 buttons to key in the manufacturer's code number from the following chart.
4
Press ENTER.
For more details on operating the cable box or satellite receiver Refer to the operating instructions that were supplied with the equipment.
If the remote control doesn’t work First, try repeating the setup procedures using the other codes listed for your equipment. Tips z • If more than one code number is listed, try
entering them one by one until you come to the correct code for your equipment.
• If you enter a new code number, the code number
you previously entered at that setting is erased.
• In some rare cases, you may not be able to operate
your equipment with the supplied remote control. In this case, use the equipment’s supplied remote control.
• Whenever you remove the batteries, the code
numbers may revert to the factory setting.
Cable box code numbers
Code
222, 223, 224, 225, 226
201, 202, 203, 204, 205,
206, 207, 208, 218
227, 228, 229 219, 220, 221
214, 215
209, 210, 211
216, 217 212, 213
Satellite receiver code numbers Manufacturer Sony General Electric Hitachi Hughes Panasonic RCA/PROSCAN Toshiba
Code
801 (preset code for
remote control)
802 805 804 803
802, 808 806, 807
Operating a Cable Box or Satellite Receiver
31
You want to restore the TV's factory settings A red light keeps flashing on the TV for more than a few seconds TV makes a noise when turned on Screen is not lit and there is no sound Poor or no picture (screen lit), good sound Good picture, no sound No color Only snow and noise appear on the screen
• Your TV may need service. • This is a normal function of your TV. • Power cord may not be plugged in. •
Remote control batteries may not be inserted correctly.
• TV/VIDEO setting may be incorrect. • Current program may exceed PARENTAL
CONTROL settings.
•
VIDEO menu settings may not be adjusted correctly.
• Antenna/cable connections may be faulty. • VIDEO LABEL inputs may be set to WEB. (This
label darkens the screen for ideal WebTV viewing)
• Sound may be set to MUTING. • Your TV may be set to SAP. • SPEAKER may not be set correctly. • Color settings may not be adjusted correctly. •
CABLE may not be set correctly in the CHANNEL SET UP menu.
• Antenna/cable connections may not be correct. • TV may be set to AUX mode.
• First, turn the TV on. Then while pressing the RESET
button on the remote control, press the POWER button on the TV. The TV will turn itself off and then back on. When the TV turns on again, all settings will be reset, and the initial setup screen will appear.
• Call your local Sony service center. • Check your power cord. • Re-insert the batteries in your remote control. • Press TV/VIDEO until you receive a channel.
• Check your PARENTAL CONTROL settings, (page 27). • Readjust your VIDEO menu settings, (page 18). • Check your VIDEO LABEL settings, (page 21). • Press MUTING. • Check the MTS setting in the AUDIO menu, (page 19). • Check your SPEAKER settings, (page 19). •
Adjust the COLOR settings in the VIDEO menu, (page 18).
• Ensure that you have selected the correct CABLE mode in
the CHANNEL SET UP menu, (page 23).
• Press ANT on your remote control to change the input
mode, (page 14).
Problem What it could be What you can do
Troubleshooting
Consult the table below; it suggests solutions to specific problems.
32
• CABLE setting may not be correct
in the CHANNEL SET UP menu.
• CABLE setting may not be correct
in the CHANNEL SET UP menu.
• Volume may not be adjusted on
your cable box.
• CHANNEL FIX settings may not
be correct.
Problem What it could be What you can do
If, after reading these operating instructions, you have additional questions related to the use of your Sony television, please call our Direct Response Center at 1-800-222-SONY (7669)(U.S. residents only) or (416) 499-SONY (7669)(Canadian residents only).
•
Ensure that CABLE is set to OFF in the CHANNEL SET UP menu, (page 23).
•
Use AUTO PROGRAM to add receivable channels that are not presently in TV memory, (page 23).
•
Ensure that CABLE is set to OFF in the CHANNEL SET UP menu, (page 23).
•
Use AUTO PROGRAM to add receivable channels that are not presently in TV memory, (page 23).
• Use the remote control supplied
with the cable box.
• Check your CHANNEL FIX
settings, (page 23).
• In the password screen, enter the
following master password: 4357. The master password cannot be used to unlock currently blocked channels.
Cannot receive upper channels (UHF) when using an antenna Cannot receive any channels when using cable Cannot gain enough volume when using a cable box TV is fixed to one channel Lost password for PARENTAL CONTROL

—9 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
SECTION 2
DISASSEMBLY
2-1. REAR COVER REMOVAL
Claw
3
Chassis Assembly
4
G Board
Two Screws
(BVTP 3x12)
2-2. CHASSIS ASSEMBLY REMOVAL
Claw
3
G Board
Chassis Assembly
Two Screws
(BVTP 4x16)
Eleven Screws
(BVTP 4x16) Eleven Screws
(BVTP 4x16)
(KV-32S42/32V42/32S66) (KV-35S42/35V42/35S66)
(KV-32S42/35S42) (KV-32S66/32V42/35S66/35V42)
4
HS Board
(KV-35S42 only)
5
HV Board
(KV-35S42 only)
4
HS Board
5
HV Board
(KV-32V42/35S66/35V42 only)

—10 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
2-4. CONTROL SWITCH REMOVAL
(KV-32V42/35V42 only)
a
REMOVAL PROCEDURES
HOW TO HANDLE AN ANODE CAP
WARNING: High voltage remains in the CRT even after the power is disconnected. To avoid electrical shock, discharge the CRT before
attempting to remove the anode cap. Short between anode and coated earth ground strap of CRT.
NOTE: After removing the anode, short circuit the anode of the picture tube and the anode cap to either the metal chassis, CRT shield,
or carbon painted on the CRT.
1
Do not use sharp objects which may cause damage to the
surface of the anode cap.
3
Do not force turn the foot of the rubber cover. This may cause
the shatter-hook terminal to protrude and damage the rubber.
2
To avoid damaging the anode cap, do not squeeze the rubber
covering too hard. A material fitting called a shatter-hook terminal
is built into the rubber.
2
Use your thumb to pull the rubber
cap firmly in the direction indicated
by arrow
b .
3
When one side of the rubber cap
separates from the anode button,
the anode cap can be removed by
turning the rubber cap and pulling
it in the direction of arrow
c .
1
Turn up one side of the rubber cap in
the direction indicated by arrow
a .
b
Anode Button
c
ANODE CAP REMOVAL
2-3. SERVICE POSITION
G Board
A Board
Four Claws
Control Switch

—11 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
2-5-1. PICTURE TUBE REMOVAL (KV-32S42/32V42/32S66)
2-5-2. PICTURE TUBE REMOVAL (KV-35S42/35V42/35S66)
Coated
Earth
Ground
Strap
WARNING:
BEFORE REMOVING
THE ANODE CAP
High voltage remains in the CRT even
after the power is disconnected. To
avoid electric shock, discharge CRT
beforeattempting to remove the anode
cap. Short between anode and CRT
coated earth ground strap.
Coated
Earth
Ground
Strap
WARNING:
BEFORE REMOVING
THE ANODE CAP
High voltage remains in the CRT even
after the power is disconnected. To
avoid electric shock, discharge CRT
beforeattempting to remove the anode
cap. Short between anode and CRT
coated earth ground strap.

—12 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
SECTION 3
SET-UP ADJUSTMENTS
5. Move the deflection yoke forward, and adjust so that
the entire screen becomes green.
6. Switch over the raster signal to red and blue and
confirm the condition.
7. When the position of the deflection yoke is deter-
mined, tighten it with the deflection yoke mounting
screw.
8. When landing at the corner is not right, adjust by
using the disk magnets.
The following adjustments should be made when a
complete realignment is required or a new picture
tube is installed.
These adjustments should be performed with rated
power supply voltage unless otherwise noted.
The controls and switch should be set as follows
unless otherwise noted:
PICTURE control.......................... normal
BRIGHTNESS control .................. normal
Perform the adjustments in order as follows:
1. Beam Landing
2. Convergence
3. Focus
4. Screen (G2)/White Balance
Note: Test Equipment Required
1. Color Bar Pattern Generator
2. Degausser
3. DC Power Supply
4. Digital Multimeter
3-1. BEAM LANDING
Preparation:
•Input a white pattern signal.
•Face the picture tube in an East or West direction
to reduce the influence of geomagnetism.
NOTE: Do not use the hand degausser because it
magnetizes the CRT .
1. Input white pattern from pattern generator.
2. Loosen the deflection yoke mounting screw, and set
the purity control to the center as shown below:
3. Input green pattern from pattern generator.
4. Move the deflection yoke backward, and adjust with
the purity control so that green is in the center and
red and blue are even on both sides.
Blue Red
Green
ab
cd
d
a
c
Purity control
corrects this area.
Disk magnets or
rotatable disk
magnets correct
these areas(a-d).
Deflection yoke positioning
corrects these areas.
b

—13 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
3-2. CONVERGENCE
Beforestarting convergenceadjustments:
1. Perform FOCUS, V. LIN andV. SIZE adjustments.
2. SetBRIGHTNESScontrol tominimum.
3. Inputdot pattern.
Vertical and Horizontal Static Convergence
1. Adjust V. STAT magnet to converge red, green and
blue dots in the center of the screen. (Vertical
movement)
B
G
RV.STAT
Magnet
Center dot
Tilt the V. STAT magnet and adjust static conver-
gence to open or close the V. STAT magnet.
2. When the V. STAT magnet is moved in the direction of
arrow aand b, red, green, and blue dots move as
shown below:
B
R
G
B
R
G
RG B
G
R
B
G
B
R
BG R
1
2
3
a
b
ab
b
b
aa
b
ba
b
ab
Operation of BMC (Hexapole) Magnet
The respective dot positions resulting from moving each
magnet interact, so perform adjustment while tracking.
Use the VSTAT tabs to adjust the red, green, and blue
dots so they line up at the center of the screen (move the
dots in a horizontal direction.)
RG B RGB RGB
RGB
RGB R GB
Y Separation Axis Correction
Magnet Adjustment
1. Input cross-hatch pattern, adjust PICTURE to
minimum and BRIGHTNESS to normal.
2. Adjust the deflection yoke upright so it touches the
CRT.
3. Adjust so that the Y separation axis correction
magnet on the neck assembly is symmetrical from
top to bottom (open state).
Purity
V. STAT
BMC (Hexapole)
4. Return the deflection yoke to its original position.

—14 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
3-4. SCREEN (G2)
1. Input dot pattern from the pattern generator.
2. Set the PICTURE and BRIGHT controls at normal.
3. Adjust S BRT, G CUT, B CUT in service mode with an oscillo-
scope so that voltages on the red, green, and blue cathodes are
170Vdc ± 2.0Vdc for 35" and 180Vdc ± 2.0Vdc for 32".
4. Observe the screen and adjust SCREEN (G2) VR
toobtain the faintlyvisible backgroundof dotsignal.
pedestal
GND
170Vdc
170 V dc/ 180 V dc
3-5. WHITE BALANCE ADJUSTMENTS
NO. Disp. Item Avg/32" Avg/35"
16 GDRV Green Drive 33 45
17 BDRV Blue Drive 33 45
18 GCUT Green Cut-off 3 6
19 BCUT Blue Cut-off 2 6
23 SBRT Sub Bright 14 10
1. Inputanentire whitesignal.
2. Setto Service adjustmentMode.
3. Set DCOL to "0"
4. Set the PICTURE and BRIGHT to minimum.
5. Adjustwith SBRTif necessary.
6. Select GCUT and BCUT with 1and 4.
7. Adjust with 3and 6for the best white balance.
8. Set the PICTURE and BRIGHT to maximum.
9. Select GDRV and BDRV with 1and 4.
10. Adjust with 3and 6for the best white balance.
11. Reset DCOL to "1".
12. Writeintothememorybypressing then **.
Dynamic Convergence Adjustment
Before starting, perform Horizontal and Vertical
Static Convergence Adjustment.
1. Slightly loosen deflection yoke screw.
2. Remove deflection yoke spacers.
3. Move the deflection yoke for best convergence as
shown below:
BGRB
G
R
B
G
R
RGB RGB
B
RGB BGR
BGRB
G
R
B
G
R
B
4. Tighten the deflection yoke screw.
5. Install the deflection yoke spacers.
Screen-corner Convergence
Affixapermalloyassemblycorresponding tothe misconverged
areas:
ab
cd
b
a
dc
a-d : screen-corner
misconvergence
3-3. FOCUS
AdjustFOCUS control forbest picture.
Focus
Screen (G2)

—15 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
Step 1 Preparation before Confirmation
Turn the POWER switch ON.
Input a white signal and set the PICTURE and BRIGHT
controls to maximum.
Confirm that the voltage of more than 18.0 VDC
appears between TP85 and ground on the A Board at
AC Input: 120.0 ± 0.2 VAC.
Step 2
Input a white signal and verify that IABLis within the
specified range: 2160 ± 100 µA(KV-35S42/S66/V42)
or 2000 ± 100 µA(KV-32S42/S66/V42).
At AC input: 120.0 ± 2.0 VAC
+
I ABL
ABL
T503
FBT
range
-
ammeter
3.0 mA DC
A
Step 3
Record the voltage between TP85 and ground.
Step 4
Using an external DC power supply, apply voltage
between TP85 and ground.
Increase the voltage gradually and confirm that the
holdown works (raster disappears) at lower than the
voltage recorded in Step 3.
Lower than 22.05 +0.0/-0.1 VDC (KV-35S42/S66/V42)
or 26.95 +0.0/-0.1 VDC (KV-32S42/S66/V42)
at AC input: 120.0 ± 2.0 VAC.
SECTION 4
SAFETY RELATED ADJUSTMENTS
4-1. R530, R531 CONFIRMATION METHOD
(HOLD-DOWN CONFIRMATION) AND
READJUSTMENTS
Alwaysperformthe followingadjustmentswhenreplacing the
followingcomponents markedwitha mark ontheschematic
diagram:
3mA DC range
+
-
+
-
A
+
-
11
T503
FBT
TP85
T503
FBT
TP85
R531 R530
DC Power Supply
digital multimeter
ammeter
A BOARD - CONDUCTOR SIDE
Step 5
Confirm that a voltage of more than
18.0 VDC (KV-35S42/S66/V42)
or21.5VDC (KV-32S42/S66/V42)
appears between TP85 and ground at AC input:
120.0 ± 2.0 VAC
4-2. B+ VOLTAGE CONFIRMATION AND
ADJUSTMENT
Alwaysperform thefollowing adjustmentswhenreplacing thefollow-
ingcomponents markedwith onthe schematicdiagram:
G BOARD: IC643, R661
1. Using a Variac, apply AC input voltage: 130 + 2.0 VAC
2. Input a monoscope signal.
3. Set the PICTURE control and the BRIGHT control to
initial reset value.
4. Confirm the voltage of G BOARD CN641 between
pin 1to ground is less than 136.5 VDC.
5. If step 4 is not satisfied, replace the R661and repeat the
above steps.
A BOARD: IC351, IC501, D519, D520, D521, C531,
C532, R387, R529, R530, R531, R532,
R533, R550, T503
G BOARD: IC643, R661

—16 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
MUTING POWER
MUTING POWER
VTR/DVD SAT/CABLE
VTR/DVD SAT/CABLE TV
—— FUNCTION ——
TV/VTR
SLEEP DISPLAY
SYSTEM
OFF
TV
DISPLAY
1
4
8
3
5
6
ENTER
123
456
9
8
7
0
JUMP ENTER
TV/SAT GUIDE
MENU
RESET
VOL CH
++
––
VOLUME
CODE SET
RM-Y168
PICTURE
MODE
MTS/SAP
5-1. Setting the Service Adjustment Mode
1. Standby mode. (Power off)
2.
Display Channel 5Sound volume Power
+
on the Remote Commander. (Press each button within a
second.)
Service Adjustment Mode In
Disp.
(Item) Item
data
SERVICE AFC 0
3. The CRT displays the item being adjusted.
4. Press or on the Remote Commander to select the item.
5.
Press or on the Remote Commander to change the data.
6. Press then to write into memory**.
Service Adjustment Mode Memory
Green
Red
SERVICE RESET
7. Press then on the Remote Commander to
initialize.
SERVICE WRITE
SECTION 5
CIRCUIT ADJUSTMENTS
RM-Y168
ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER
Use the Remote Commander (RM-Y168) to perform the circuit adjustments in this section.
NOTE: Test Equipment Required:
• Pattern generator
• Frequency counter
• Digitalmultimeter
• Audiooscillator
Carry out step 7 when adjusting
IDs 0 to 4 and when replacing
and adjusting IC002.
8. Turn set off and on to exit. * CAUTION: Wait at least 10
seconds before turning off set.
5-2. MemoryWrite Confirmation Method
1. After adjustment, pull out the plug from theAC outlet, then
replace the plug in theAC outlet again.
2. Turn the power switch ON and set to Service Mode.
3. Call the adjusted items again to confirm they were adjusted.
5-3. Adjust Buttons and Indicator
**WARNING: Do NOTturn off the power orAC immediately after pressing then . Wait at least 10 seconds.

—17 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
**AVERAGE DATA MODEL GROUPINGS:
32" A: KV-32S42 35" G: KV-35S42
C: KV-32S66 I: KV-35S66
D: KV-32V42 L: KV-35V42
No. Register
Name Description Data Adj/Fix Initial Average Data** Comments
Range Data 32" 35"
A,C G I L
VP CXA2095S
1
VPOS V-Position 0-63 Adj 20 23 33 0:Down, 63:Up
2
VSIZ V-Size 0-63 Adj 20 27 52 0:Min, 63:Max
3
VCOM V-Compensation 0-3 Fix 1 1 0:Min, 3:Max
4
VLIN V-Linearity 0-15 Adj 79 0:Min, 15:Max
5
VSCO S-Correction 0-15 Adj 76 9 0:Min, 15:Max
6
HPOS H-Position 0-15 Adj 711 10 0:Right, 15:Left
7
HSIZ H-Size 0-63 Adj 20 23 39 0:Min, 63:Max
8
PAMP Pin Compensation 0-63 Adj 31 27 19 0:Min, 63:Max
9
UPIN Upper Corner Pin 0-15 Adj 74 7 0:Min, 15:Max
10
LPIN Lower Corner Pin 0-15 Adj 76 10 0:Min, 15:Max
11
PPHA Pin Phase 0-15 Adj 74 5 0:Min(small picture), 15:Max
12
AFC AFC 0-3 Fix 2 2 0:Freerun, 1:Min, 3:Max
13
VBOW AFC Bow 0-15 Adj 76 5 0:Right, 15:Left
14
VANG AFC Angle 0-15 Adj 76 4 0:Right, 15:Left
15
REF Reference Line 0-3 Fix 2 2 0:22H(Rch), 3:16H(Rch)
16
GDRV Green Drive 0-63 Adj 31 22 35 0:Min, 63:Max
17
BDRV Blue Drive 0-63 Adj 31 30 26 0:Min, 63:Max
18
GCUT Green Cutoff 0-15 Adj 75 8 0:Min, 15:Max
19
BCUT Blue Cutoff 0-15 Adj 77 6 0:Min, 15:Max
20
SCON Sub Contrast 0-15 Adj 710 8 0:Min, 15:Max
21
SHUE Sub Hue (RF only) 0-15 Adj 70:+10deg, 15:-10deg
22
1SHU Sub Hue (composite & S-video) 0-15 Adj 70:+10deg, 15:-10deg
23
SCOL Sub Color (RF only) 0-15 Adj 70:Min, 15:Max
24
1SCO Sub Color (composite & S-video) 0-15 Adj 70:Min, 15:Max
25
SBRT Sub Brightness 0-63 Adj 31 26 0:Min, 63:Max
26
SSHP Sub Sharpness (RF & Composite video) 0-15 Fix by model 7 10 10 0:Min, 15:Max
27
1SSP Sub Sharpness (S-video only) 0-15 Fix by model 7 10 10 0:Min, 15:Max
28
GMMA Gamma Correction 0-3 Fix by model 1 0 0 0:Off, 1:Min, 3:Max
29
CDM2 Countdown Mode 2 0-1 Fix 0 00: Normal 1: High Speed
Countdown Respons
e
30
EYSW External Y Switch 0-1 Fix 0 0 0: Normal 1: EYin disabled
31
DPIX Dynamic Picture 0,1 Fix 1 1 0:Off, 1:On
32
Y-DC DC Transmission Ratio 0,1 Fix 1 1 0:100%, 1:82%
33
ABLM ABL Mode 0,1 Fix 1 10:PictureABL,
1:Picture/Bri
g
htnessAB
L
34
AXIS Color Demodulation Axis 0,1 Fix 1 0 0:Japan, 1:US
35
NOTC Chroma Trap Filter 0,1 Fix 0 0 0:Off, 1:On
36
CROM Chroma Trap Adjust 0-15 Fix 7 7 0:+300kHz, 1:-300kHz
37
TOT TOT Filter (RF only) 0,1 Fix 1 1 0:Off, 1:On
38
1TOT TOT Filter (Composite & S-video) 0,1 Fix 1 0 0:Off, 1:On
39
PREL Pre/Overshoot Ratio (RF & Composite) 0-3 Fix by model 3 1 0: 2:1, 3: 5:1
40
1PRE Pre/Overshoot Ratio (S-video only) 0-3 Fix by model 3 3 0: 2:1, 3: 5:1
41
SHPF Sharpness fo (RF & Composite) 0-3 Fix by model 2 1 0:2.5MHz, 3:4.0MHz
42
1SPF Sharpness fo (S-video only) 0-3 Fix by model 2 3 0:2.5MHz, 3:4.0MHz
43
RON Red Off 0,1 Fix 1 1 0:Off, 1:On
44
GON Green Off 0,1 Fix 1 1 0:Off, 1:On
45
BON Blue Off 0,1 Fix 1 1 0:Off, 1:On
46
DCOL Dynamic Color 0,1 Fix 0 1 (adjusted @ 0, but shipped as 1) 0:Off, 1:On
47
CDMD V Countdown Mode 0,1 Fix 0 0 0:Auto, 1:Fix
48
HBSW H Blanking Switch 0,1 Fix 0 0 0:Off, 1:On
49
LBLK Left Blanking 0-15 Fix 0 7 0:Min, 15:Max
50
RBLK Right Blanking 0-15 Fix 0 7 0:Min, 15:Max
AP CXA2021
51
SVOL Sub Volume 0-15 Fix 0 60:-0 Volume steps, 15:-15 Volume
steps
52
SBAL Sub Balance 0-15 Fix 7 7 0: +Right, 15:+Left
53
SBAS Sub Bass 0-15 Fix by model 7 8 7 8 10 0:-7 Steps, 15: +8 steps
54
STRE Sub Treble 0-15 Fix by model 7 10 7 10 7 0:-7 Steps, 15: +8 steps
MM1311/1313
55
AUSW Audio Att Sw 0,1 Fix 1 10:-6dB, 1:0dB (Only for VIDEO
input
)
7(adjust flat - 1 step)
7 (same as SHUE adjusted value)
11 (adjust flat + 2 steps)
9 (SCOL adjusted flat, no offset)
D
5-4. Adjustment Items

—18 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
No. Register
Name Description Data Adj/Fix Initial Average Data** Comments
Range Data 32" 35"
A,C G I L
PI SDA9288
56
PYSD Select Delay 0-15 Fix by P-bd 3 0:Right, 15:Left
57
PIPH PIP H-position 0-127 Fix 78 78 0:Right, 127:Left
58
PIPV PIP V-position 0-63 Fix 18 18 0:Up, 63:Down
59
PYDL PIP Y-delay 0-7 Fix 0 0 0:Right, 7:Left
60
PHDL H-pulse delay 0-15 Fix by P-bd 3 0 0:Right, 15:Left
61
PMVD Main V-pulse delay 0-31 Fix 16 16 7-21: Available (1-6/22-31 Not
Avail
)
62
PIVD Inset V-pulse delay 0-31 Fix 22 22 16-28 Available (1-15/29-31 Not
Avail
)
63
PCON Inset Contrast 0-15 Fix 7 6 0:Min, 15:Max
64
FRMY Frame Y 0-15 Fix 7 7 0:Dark, 15:Bright
65
CHRI Input Polarity 0,1 Fix by P-bd 1 1 0:+(B-Y)+(R-Y), 1:-(B-Y)-(R-Y)
66
CHRO Output Polarity 0,1 Fix 1 1 0:+(B-Y)+(R-Y), 1:-(B-Y)-(R-Y)
67
IPER Inset Pedestal R-Y 0-15 Fix 0 0 0:Center, 7:Max, 8:Min
68
IPEB Inset Pedestal B-Y 0-15 Fix 0 0 0:Center, 7:Max, 8:Min
69
PCPS CLPS Bit Control 0,1 Fix 0 00:Depend on HSIDEL, 1:Not
depend
70
PCPF CLPFIX Bit Control 0,1 Fix 0 0 0: 3Clamp line, 1: 2Clamp line
71
PSEL SELDOWN Bit Control 0,1 Fix by P-bd 1 1 0:Open out, 1:TTL out
72
PPLL PLL Filter Bits 0-3 Fix 0 0 Fixed value only
73
PVNR VSPISQ VSP NR 0-1 Fix 0 1 SDA9288 IC bypass use 1
IC CXA2019
74
ISCO CDec Sub Contrast 0-15 Fix 7 15 PiP sub contrast
75
ISHP CDec Sharpness 0-15 Fix 7 8 PiP sharpness
76
ISCL CDec Sub Color 0-15 Fix 7 9 PiP sub color
77
ISHU CDec Sub Hue 0-15 Fix 7 6 PiP sub hue
78
ITOT CDec TOT on 0,1 Fix 0 1 PiP TOT 0:Off, 1:On
79
IAFC CDec AFC 0-3 Fix 2 2 0:Max, 2:Min, 3:Freerun
80
ICD2 CDec Countdown Mode2 0,1 Fix 0 0 0:Standard, 1:Fast
81
IYDR CDec Y drive 0-31 Fix 15 7 PiP Y-drive gain
82
IVPE CDec V pedestal 0-15 Fix 7 6 PiP V-ped DC
83
IUPE CDec U pedestal 0-15 Fix 7 6 PiP U-ped DC
84
IRVP CDec RV pedestal 0-15 Fix 7 6 PiP V-ped DC (re-input)
85
IRUP CDec RU pedestal 0-15 Fix 7 6 PiP U-ped DC (re-input)
86
IDCT CDec DC transfer 0-7 Fix 2 0 PiP DC transfer 0:Max, 7:Min
87
IRYD CDec RY drive 0-31 Fix 15 20 PiP RY Drive (re-input)
88
IABO CDec ABL off 0,1 Fix 1 1 PiP ABL (RY-OUT) 0:On, 1:Off
89
IPRE CDec Pre/Over shoot 0-3 Fix 3 3 PiP Pre/over shoot 0: 1:1, 1: 4:1
90
IRUD CDec RU Drive 0-31 Fix 15 20 PiP RU-gain out 0:-6dB, 31:+3.3bD
91
IABL CDec ABL 0,1 Fix 1 1 PiP ABL gain 0:Std, 1:Min
92
IABC CDec ABL Cent 0-3 Fix 1 1 PiP ABL Center 0:Min, 1:Max
93
IRVD CDec RV drive 0-31 Fix 15 17 PiP RY Drive (re-input)
94
IDLY CDec Delay 0-3 Fix 0 0PiP Y-delay 0:0ns, 1:60ns, 2:120ns
3:180n
s
95
ISCR CDec SCP BGR 0-3 Fix 0 0PiP SCP riseup phase 0:+0.4us,
1:cent, 2:-0.8u
s
96
ISCF CDec SCP BGF 0-3 Fix 0 0PiP SCP falldown phase 0:+0.4us,
1:cent, 2:-0.8us
97
PFRN VCXO Oscillation 0,1 Fix 0 0: Lock 1: Free Run…FREE_RUN
98
PRVS HD/VD Input Synchronous Mode Selection 0,1 Fix 0 0: Sync 1: Async…RVS
99
PCON Sub-Contrast 0-127 Fix 32 0: Min 127: Max…CONTRAST
100
PUCO Sub U Level Control 0-15 Fix 7 0: Min 15: Max…calculated
101
PVCO Sub V Level Control 0-15 Fix 7 0: Min 15: Max…calculated
102
PHUE Hue 0-31 Fix 15 0: Red 31: Green…calculated
103
PKIL Color Killer 0,1 Fix 0 0: Enable 1: Disable…KILLER
104
PSEP C-Sync Sep Input Selection 0-3 Fix 2 0: Digital 1:23pin in 2:ext 18p 3:int
analo
g
…EXT_SC_SE
L
105
PDCO Digital Sync Sep Threshold Setting 0-3 Fix 0 Threshold Setting…DCOUNT
106
PEXP Ext Port Setting 0-3 Fix 2 0/1: Sub BGP 2: "0" out 3: "1"
out…EXPOR
T
107
PBGS BGP Position Setting 0-63 Fix 14 Sub Picture BGP
Position…BG_START
108
PYDL Y/C Delay Adjust 0-15 Fix 7 Sub Picture Y/C Delay…YDL
109
PBRT Y Brightness 0-31 Fix 25 Sub Picture Y Bright
Control…Y_OFFSET
110
PVPE V Pedestal Level 0-15 Fix 0 V Pedestal Level (2's
comp)…PEDESTV
111
PUPE U Pedestal Level 0-15 Fix 0 U Pedestal Level (2's
comp
)
…PEDESTU
112
PACS 0Dh/0Eh Setting Mode 0,1 Fix 1
113
PSDL Sync Delay 0-3 Fix 0
114
PMVP Macrovision Mode Selection 0-3 Fix 0
115
PCGA Chrome Gain Mode 0,1 Fix 1
116
PBIT Y Clamp Time Constant 0,1 Fix 0
117
PAFC AFC Time Constant 0,1 Fix 0
7
7
11
PI + CD + PiP + Vchip
0
0
40
0
2
0
2
14
7
25
0
0
1
0
0
1
0
0
D
Adjustment Items (cont.)
**AVERAGE DATA MODEL GROUPINGS:
32" A: KV-32S42 35" G: KV-35S42
C: KV-32S66 I: KV-35S66
D: KV-32V42 L: KV-35V42

—19 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
No. Description Data Adj/Fix Initial Average Data** Comments
Range Data 32" 35"
A,C G I L
118
PACC Color Decoder Amplitude 0-63 Fix 15
119
PBUR VCXO Mode Selection 0,1 Fix 0
120
PEVE Main Picture PAL-N 0,1 Fix 0
121
PINW Invert Sub Picture Field Definition 0,1 Fix 0
122
PINR Invert Main Picture Field Definition 0,1 Fix 0
123
PREF Main Picture Field Fix 0,1 Fix 0
124
PARE Auto 50/60 Hz Detection 0,1 Fix 1
125
PAVE Sub Picture Decode Mode 0,1 Fix 0
126
PFRA Freq Adj for Free Run Mode 0-15 Fix 0
127
PPAL Parameter Setting for PAL-M Judgement 0-255 Fix 0
128
PHPO Sub Picture H Position 0-31 Fix 6
129
PVPO Sub Picture V Position 0-31 Fix 22
130
PHTI Display Timing Adjustment 0-15 Fix 10
131
PHAJ Main/Sub Switch Delay Control 0-15 Fix 2
132
PBGY Background Y Level Setting 0-15 Fix 0
133
PCRO Sub Picture Read Mode 0,1 Fix 0
134
PPAR Threshold Control For Ident Judge of Subject 0-63 Fix 2
135
PHPF Y Output HPF 0,1 Fix 1
136
PVCH 15h, 16h, 17h Setting Mode 0,1 Fix 0
137
PVON Sub V-Chip Decode Mode 0,1 Fix 1
138
PVLN Sub V-Chip Slicer Line Select 0-31 Fix 17
139
PVSB Sub V-Chip Slicer Start Bit Detect Param 0-255 Fix 64
140
PVLV Sub V-Chip Data Slicer Level Param 0-255 Fix 130
No. Register Description Data Adj/Fix Initial Average Data** Comments
Name Range Data 32" 35"
A,C G I L
CC CXP85840a-011s
141
CRIL CC CRI count low 0-15 Fix 2 2 7 Clock Run-In Lower Limit (field 1)
142
CFLD CC Caption Fixed Field Count 0-15 Fix 5 5 Fixed value only
143
CCDI CC CCD int 0-7 Fix 3 3 Fixed value only
144
CRIP CC CRI & polarity 0-7 Fix 4 4 Fixed value only
145
CRIT CC CRI time constant 0-3 Fix 1 1 Fixed value only
146
CSB1 CC Sync Slice Bias 1 0-3 Fix 3 3 Fixed value only
147
CSB2 CC Synce Slice Bias 2 0-7 Fix 4 4 Fixed value only
148
CREP CC CRI signal end position 0-255 Fix 142 142 Fixed value only
149
CDSD CC Data start delay 0-31 Fix 8 8 Fixed value only
150
CCDS CC Caption data threshold 0-31 Fix 9 9 Fixed value only
151
CHMK CC P8_HMASK 0-63 Fix 42 42 Hmask
152
CHSY CC P8_HSYC 0-255 Fix 136 136 Hsyc
153
DISP TV OSD H Position 0-63 Adj 123 0:Off, 1:Left, 63: Right
154
RTCO Rotation Coil 0-63 Fix 32 32 Fixed value only
ID MAP
155
ID-0 ID-0 (Language/Color Systems) 0-255 Fix by model 89 See ID map
156
ID-1 ID-1 (Input/Output Conifguration) 0-255 Fix by model 55 See ID map
157
ID-2 ID-2 (Audio) 0-255 Fix by model 175 See ID map
158
ID-3 ID-3 (OSD/Timer/V-chip/Ch Fix) 0-255 Fix by model 0
Refer to
See ID map
159
ID-4 ID-4 (CC/Spot Killer/etc) 0-255 Fix by model 155
Feature ID Map
See ID map
160
ID-5 ID-5 (V-series Features/etc) 0-255 Fix by model 141 See ID map
161
ID-6 ID-6 (PiP/Ant Sw related) 0-255 Fix by model 6 See ID map
162
ID-7 ID-7 (Special Models/etc) 0-255 Fix by model 0 See ID map
15
D
0
0
0
0
0
1
0
0
0
0
2
0
15
22
10
64
130
D
0
0
1
17
2
Register
Name
5-5. Feature ID Map
Adjustment Items (cont.)
SERVICE IDO 25
Note: Items 1-162 show adjustment order
**AVERAGE DATA MODEL GROUPINGS:
32" A: KV-32S42 35" G: KV-35S42
C: KV-32S66 I: KV-35S66
D: KV-32V42 L: KV-35V42

—20 —
KV-32S42/32S66/32V42/35S42/35S66/35V42
10. Return the following back to normal after adjustment.
PICTURE......................MAX
COLOR.........................MIN
BRIGHT ........................CENTER
R ON ............................ON (1)
G ON ............................ON (1)
B ON.............................ON (1)
DISPLAY POSITION ADJUSTMENT (DISP)
1. Input a color-bar signal.
2. Set to Service adjustment Mode.
3. Select DISP with and .
4. Adjust with and for adjustment of characters to center .
5. Write the memory by pressing then **.
SERVICE AFC 0
SUB HUE, SUB COLOR ADJUSTMENT
(SHUE, SCOL)
1. Input a color-bar signal.
2. Set to Service adjustment Mode.
3. Connect oscilloscope probe to C Board, CN1761 Pin3
(BLUE OUT).
4. Select SHUE and SCOL with and .
5. Adjust with and for theV1 = V4 ± 0.1Vp-p (SCOL)
and V2 =V3 ± 0.1Vp-p (SHUE).
V1 V2 V3 V4
6. Change data according to the following table:
SCOL SHUE
32" +2 steps -1 steps
35" +2 steps -1 steps
7. Writeinto thememory bypressing then
**.
SUB BRIGHT ADJUSTMENT (SBRT)
1. Set to Service adjustment Mode.
2. Input a gray scale pattern signal.
3. Set the PICTURE to minimum, and BRIGHT to normal.
4. Select SBRT with and .
5. Adjust SUB BRIGHT level with and so that the stripe
second from the right is faintly visible.
6. Write into the memory by pressing then
**.
white
black
second from the right
SUB CONTRAST ADJUSTMENT (SCON)
1. Input a color-bar signal.
2. Set to Service adjustment Mode.
3. Select the item DCOL to "0" level.
4. Set the conditions as follows.
PICTURE......................MAX
COLOR.........................MIN
BRIGHT ........................CENTER
R ON ...........................ON (1)
G ON ...........................OFF (0)
B ON............................OFF (0)
SERVICE RON 1
5. Connect an oscilloscope probe to C Board, CN1761 pin 1
(RED OUT).
6. Select SCON with and .
7. Adjust with and for: 1.80 ± 0.05 Vp-p.
1.80 ±0.5 Vp-p
White
Black
8. Reset the item DCOL to "1" level.
9. Write the memory by pressing then ** .
**WARNING: Do NOTturn off the power orAC immediately after pressing then . Wait at least 10 seconds.