Sony KV-XF34K94 User manual

http://cxema.ru
MODEL COMMANDER DEST. CHASSIS NO.
KV-XF34K94 RM-962 Korean SCC-U35C-A
MODEL COMMANDER DEST. CHASSIS NO.
CHASSIS
TRINITRON ® COLOR TV
SERVICE MANUAL BG-3S
Self Diagnosis
Supported model
231
564
897
0
ENTER JUMP
MUTING
MTS VIDEO
PIC
MODE
TV/VIDEO FREEZE SWAP PIP
TV
DISPLAY POWER
CHVOL
MENU
FAVORITE
SURROUND
AUTOPROGR ADD/ERASECABLE
WAKEUP
SOUND
MODE
TV
PIPCH
PIPCH
SLEEP

http://cxema.ru
– 2 –
KV-XF34K94
RM-962
SPECIFICATIONS
Note
Power requirements 110-220 V AC, 50/60 Hz
Power consumption (W) Indicated on the rear of the TV
Television system M
Color system NTSC3.58
Stereo/Bilingual system Korean Stereo
Channel coverage
MVHF: A2 to A13 / UHF: A14 to A69 /
CATV: 1 to 125
˘(Antenna) 75-ohm external terminal
Audio output 8W + 8W
Number of terminal
Video Input: 4* Output: 1 Phono jacks; 1VP-P, 75 ohms * Three input lines available
Audio Input: 4* Output: 1 Phono jacks; 500 mVrms * Three input lines available
S Video Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync
negative
C : 0.286 Vp-p, 75 ohms
2(Headphone) Output: 1 Stereo Minijack
Picture tube 34 inch
Tube size (cm) 86 Measured diagonally
Screen size (cm) 80 Measured diagonally
Dimension (w/h/d, mm) 915 ×670 ×584
Mass (kg) 81
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK !ON
THE SCHEMATIC DIAGRAMS,EXPLODEDVIEWS AND INTHE
PARTS LIST ARE CRITICALTO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAPTOTHE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.

http://cxema.ru
– 3 –
KV-XF34K94
RM-962
TABLE OF CONTENTS
Section Title Page
SELF DIAGNOSIS FUNCTION................................ 4
1. GENERAL........................................................................ 8
2. DISASSEMBLY
2-1. Rear Cover Removal................................................ 25
2-2. Speaker Removal ..................................................... 25
2-3. Chassis Assy Removal ............................................. 25
2-4. F Bracket Removal .................................................. 25
2-5. Service Position ....................................................... 26
2-6. Replacement of Parts ............................................... 26
2-6-1. Replacement of Control Button ..................................... 26
2-6-2. Replacement of Light Guide .......................................... 26
2-7. D2 Board Removal .................................................. 26
2-8. HV Block, PWB Holder and Terminal Bracket ......
Removal ................................................................... 27
2-9. H3 Board Removal .................................................. 27
2-10. P2 and V1 Boards Removal..................................... 27
2-11. A and B3 Boards Removal ...................................... 27
2-12. Picture Tube Removal.............................................. 28
3. SET-UP ADJUSTMENTS
3-1. Beam Landing .......................................................... 29
3-2. Convergence............................................................. 30
3-3. Focus Adjustment .................................................... 32
3-4. G2 (Screen) and White BalanceAdjustments......... 33
4. CIRCUIT ADJUSTMENT
4-1. Adjustments with Commander ................................ 34
4-2. Adjustment Method ................................................. 35
4-3. Picture Quality Adjustments.................................... 40
4-4. Display Position Adjustment ................................... 40
4-5. A Board Adjustment After IC003 (Memory)
Replacement............................................................. 40
4-6. Picture Distortion Adjustment ................................. 41
Section Title Page
5. DIAGRAMS
5-1. Block Diagram ......................................................... 43
5-2. Frame Schematic Diagram ...................................... 47
5-3 Circuit Boards Location .......................................... 51
5-4. Schematic Diagrams and Printed Wiring Boards ... 52
(1) Schematic Diagram ofA (1/2) Board...................... 55
(2) Schematic Diagram ofA (2/2) Board...................... 59
(3) Schematic Diagram of F Board ............................... 63
(4) Schematic Diagram of B3 Board ............................ 67
(5) Schematic Diagram of C Board .............................. 75
(6) Schematic Diagram of P2 Board .............................. 79
(7) Schematic Diagrams of B7 and H3 Boards ........... 82
(8) Schematic Diagram of VM1 Board ........................ 87
(9) Schematic Diagram of D2 Board ........................... 89
5-5. Semiconductors....................................................... 92
6. EXPLODED VIEWS
6-1. Speaker Bracket ...................................................... 95
6-2. Chassis .................................................................... 96
6-3. Picture Tube ............................................................ 97
7. ELECTRICAL PARTS LIST...................................... 98

http://cxema.ru
– 4 –
KV-XF34K94
RM-962
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1. DIAGNOSTICTEST INDICATORS
When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic
Item
Description
• Power does not
turn on
• +B overcurrent
(OCP) or
overvoltage
(OVP)
• Vertical deflection
stopped
• Horizontal
deflection
overdrive
• White balance
failure (no
PICTURE)
• Micro reset
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
5 times
—
Self-diagnostic
display/Diagnostic
result
—
002:000 or
002:001~255
003:001~255
004:001~255
at the same time
005:000 or
005:001~225
101:00 or
101:001~225
Probable
Cause
Location
• Power cord is not plugged
in.
• Fuse is burned out F4601
(F)
• H.OUT Q511 is shorted.(A
board)
• IC701 is shorted. (C board)
• -13V is not supplied. (A
board)
• IC 503 faulty (A board)
• G2 is improperly adjusted.
(Note 2)
• CRT problem.
• Video OUT IC701 is faulty.
(C board)
• IC301 is faulty. (A board)
• No connection A board to C
board.
• Discharge CRT (C Board)
• Static discharge
• External noise
Detected
Symptoms
• Power does not come on.
• No power is supplied to the
TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is
shorted.
• Has entered standby state
after horizontal raster.
• Vertical deflection pulse is
stopped.
• Power line is shorted or
power supply is stopped.
• No raster is generated.
• CRT cathode current
detection reference pulse
output is small.
• Power is shut down shortly,
after this return back to
normal.
• Detect Micro latch up.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
SELF DIAGNOSTIC FUNCTION

http://cxema.ru
– 5 –
KV-XF34K94
RM-962
2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
Diagnostic Item Flash Count*
+B overcurrent/overvoltage 2 times
Vertical deflection stopped
White balance failure 5 times
* One flash count is not used for self-diagnostic.
3. STOPPINGTHE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.
Lamp ON 0.3 sec. Lamp OFF 3 sec.
Lamp OFF 0.3 sec.
2 times
5 times
STANDBY/SLEEP lamp

http://cxema.ru
– 6 –
KV-XF34K94
RM-962
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screendisplay] /channel [5] /Sound volume [-] /Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel [8] /0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
002 : 000
003 : 000
004 : 000
005 : 001
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
101 : 000
SELF DIAGNOSTIC

http://cxema.ru
– 7 –
KV-XF34K94
RM-962
6. SELF-DIAGNOSTIC CIRCUIT
[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[ hitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301.TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
IC301
Y/CHROMA JUNGLE
FROM
CRT
FROM
[+B] Q604 C
[V] Q509/507
IC001
SYSTEM IC003 MEMORY
B-DAT
IO-SDAT
IK-IN
MP/
PROTECT
IO-8DAT
O-LED
SDA
54521
18 51
4635

http://cxema.ru
– 25 –
KV-XF34K94
RM-962
SECTION 2
DISASSEMBLY
2-3. CHASSIS ASSY REMOVAL
2-2. SPEAKER REMOVAL
1Four screws (Washer head) (+P 4 × 16)
2Bracket, speaker
1Chassis assy
2-1. REAR COVER REMOVAL
1Ten screws (+BVTP 4 × 16)
1Three screws (+BVTP 4 × 16)
2Rear cover
2-4. F BRACKET REMOVAL
4Two screws (+BVTP 3 × 12)
5F bracket
2Two claws
1Three connectors
3F board

http://cxema.ru
– 26 –
KV-XF34K94
RM-962
2-7. D2 BOARD REMOVAL
1Three connectors
2One claw
3D2 board
2-6-2. REPLACEMENT OF LIGHT GUIDE
2-5. SERVICE POSITION
(Note: RemoveFBracketfir st.)
2-6. REPLACEMENT OF PARTS For replacement of the Control Button and Light Guide, unscrew them, exchange with the new parts, and fix them with screws (+BVTP) respectively.
2-6-1. REPLACEMENT OF CONTROL BUTTON
Control button
Two screws (+BVTP 3 × 12)
One screw (+BVTP 3 × 12)

http://cxema.ru
– 27 –
KV-XF34K94
RM-962
2-8. HV BLOCK, PWB HOLDER ANDTERMINAL BRACKET REMOVAL
2-9. H3 BOARD REMOVAL
3Two connectors
6One screw (+BVTAP 3 ×12)
1Two connectors
4Four claws
5H3 Board 2Four connectors
2-10. P2 BOARD REMOVAL
NOTE : V1 board is not used for this model
3B3 Board
5A Board
3Five connectors
1One screw (+BVTAP 3 × 12)
One screw
(+BVTAP 3 × 12
with washer)
2Three screws (+BVTAP 3 × 12)
2-11. A AND B3 BOARDS REMOVAL
3Two claws
1Two claws
4V1 board
2P2 board
1Two screws (+BVTP 3 ×12)
One screw (+BVTP 4 ×16)
2Two claws
3Terminal bracket
5Two screws (+BVTP 3 × 12)
4HV Block
6Two screws (+BVTP 3 × 12)
PWB Holder

http://cxema.ru
– 28 –
KV-XF34K94
RM-962
•REMOVAL OF ANODE-CAP
NOTE : After removing the anode, short circuit the anode of the picture tube and
the anode cap to the metal chassis, CRT shield or carbon paint on the CRT.
•REMOVING PROCEDURES
1Do not damage the surface of anode-caps with sharp shaped objects.
2Do not press the rubber too hard so as not to damage the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built into the rubber.
3Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the rubber.
•HOW TO HANDLE AN ANODE-CAP
3When one side of the rubber cap is separated from the anode button, the anode-cap
can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c.
2Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.
1Turn up one side of the rubber cap in the direction indicated by the arrow a.
2-12. PICTURETUBE REMOVAL
!¡ Four DGC clips !¶ DGC holder
!™ Demagnetic coil
0Four claws
1Four screws
(washer head) (+P 4 × 16)
3Four screws
(washer head) (+P 4 × 16)
2Speaker Bracket
assy (L)
4Speaker Bracket
assy (R)
!¢ Nut,
special CRT
Nut, special CRT
Cap, screw
Cap, screw
6Chassis assy
9Deflection
yoke
8Neck assy 7C board
5Anode cap
!∞ Picture tube
!§ Two DGC bands
Cushion
!¢
!£ Tension
spring
!•
Cushion DGC
a
a
b
b
c
Anode button

http://cxema.ru
– 29 –
KV-XF34K94
RM-962
•The following adjustments should be made when a complete
realignment is required or a new picture tube is installed.
•These adjustments should be performed with rated power
supply voltage unless otherwise noted.
Controlsand switches should besetas follows unless otherwisenoted:
PICTURE control........................................................... normal
BRIGHTNESS control................................................... normal
Perform the adjustments in the following order :
1. Beam Landing
2. Convergence
3. Focus
4. White Balance
Note : Test Equipment Required.
1. Color-bar/Pattern Generator
2. Degausser
3. Oscilloscope
SECTION 3
SET-UP ADJUSTMENTS
................................................................................................................................................................................................................................
Fig. 3-3
}normal
Neck assy
G2G1 G3
Behind the G2 edge
Fig. 3-1
Red Blue
Green
Preparation :
•In order to reduce the influence of geomagnetism on the set's
picture tube, face it east or west.
•Switch on the set's power and degauss with the degausser.
3-1. BEAM LANDING
1. Input a white signal with the pattern generator.
Contrast
Brightness
2. Position neck assy as shown in Fig3-2.
3. Set the pattern generator raster signal to a green raster.
4. Move the deflection yoke to the rear and adjust with the purity
control so that the green is at the center and the blue and the red
take up equally sized areas on each side.
(See Figures 3-1 through 3-3.)
5. Move the deflection yoke forward and adjust so that the entire
screen is green. (See Figure 3-1.)
6. Switch the raster signal to blue, then to red and verify the
condition.
7. When the position of the deflection yoke has been decided,
fasten the deflection yoke with the screws and DY spacers.
8. If the beam does not land correctly in all the corners, use a
magnet to adjust it.
(See Figure 3-4.)
Fig. 3-2
Fig. 3-4
Purity control
corrects this area. Disk magnets or rotatable
disk magnets correct these
areas (a-d).
Deflection yoke positioning
corrects these areas.
a
b
b
c
c
d
d
a

http://cxema.ru
– 30 –
KV-XF34K94
RM-962
3-2. CONVERGENCE
Preparation :
•Before starting this adjustment, adjust the focus, horizontal size
and vertical size.
•Minimize the brightness setting.
•Provide dot pattern.
(1) Horizontal and Vertical Static Convergence
1. (Moving horizontally), adjust the H.STAT control so that the
red, green and blue dots are on top of each other at the center of
the screen.
2. (Moving vertically), adjust theV.STAT magnet so that the red,
green and blue dots are on top of each other at the center of the
screen.
3. If the H.STAT variable resistor cannot bring the red, green and
blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below.
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform adjustments
while tracking.)
Center dot
R G B
R
G
B
H. STAT VR V. STAT
Magnet
RV702
H. STAT
C Board
3BMC (Hexapole) Magnet.
If the red, green and blue dots are not balanced or aligned, then
use the BMC magnet to adjust in the manner described below.
R
R
R
R
G
G
G
G
B
B
B
B
a
a
a
b
b
b b
RG B R G B R GB
RB
RG
GGB RB
1V. STAT
2H. STAT VR

http://cxema.ru
– 31 –
KV-XF34K94
RM-962
Blue
Red
VM1 board
Blue
Red
VM1 board
Neck assy Neck assy
4Y separation axis correction magnet adjustment.
1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN]
and [BRIGHTNESS] to [STANDARD] .
2. Adjust the Y separation axis correction magnet on the neck
assembly so that the horizontal lines at the top and bottom of
the screen are straight.
Note
1. The Red and Blue magnets should be equally far from the
horizontal center line.
2. Do not separate the Red and Blue magnets too far. (Less than
8 mm)
(2) Dynamic Convergence Adjustment
Preparation:
•Before starting this adjustment, adjust the horizontal static
convergence and the vertical static convergence
RB
RB
TLH TLV
YCH XCV
B
R
R
B

http://cxema.ru
– 32 –
KV-XF34K94
RM-962
(3) Screen-corner Convergence
ba
cd
a-d : screen-corner
misconvergence
Fix a Permalloy assy corresponding to the misconverged
areas.
a
b
c
d
Permalloy assembly
3-3. FOCUS ADJUSTMENT
Adjust FOCUS control on the flyback transformer for the best
focus.
FLYBACK TRANSFORMER (T503)
Screen
Focus
TLV Rotate TLV-2 VOL (29”, 34”) on DY
Rotate TLV VOL (25”) on DY
XCV Rotate XCV Adj core on DY
YCH Rotate YCH VOL on DY
TLH Insert TLH Correction Plate to DY Pocket (Left or
Right)
ON DY:
YCH
XCV
TLV1
TLV2

http://cxema.ru
– 33 –
KV-XF34K94
RM-962
2. WHITE BALANCE ADJUSTMENT
1) Set to Service Mode (Refer Section 4-1: ADJUSTMENTS
WITH COMMANDER).
2) Input white raster signal.
3) Set the PICTURE to minimum.
4) Select GCT (WHB 4) and BCT (WHB 5) with [1] and [4], and
adjust the level with [3] and [6] for the best white balance.
5) Set the PICTURE to maximum.
6) Select GDR (WHB 1) and BDR (WHB 2) with [1] and [4], and
adjust the level with [3] and [6] for the best white balance.
7) Write into the memory by pressing [MUTING] then [0].
3. SUB BRIGHT ADJUSTMENT
1) Set to service mode.
2) Input a staircase signal of black to white from the pattern
generator.
3) BRIGHTNESS....50%.
PICTURE ............MINIMUM
4) Select SBR (WHB7) with [1] and [4], and adjust SBR (WHB7)
level with [3] and [6] so that the second stripe from the right is
dimly lit.
3-4. G2 (SCREEN) AND WHITE BALANCE
ADJUSTMENTS
1. G2 (SCREEN) ADJUSTMENT
1) Set the PICTURE and BRIGHTNESS to normal.
2) Put to VIDEO mode without signals.
3) Connect R, G and B of the C board cathode to the oscilloscope.
4) Adjust BRIGHTNESS to obtain the cathode voltage to the value
below.
5) Adjust G2 (screen) on the FBT until picture shows the point
before cut off.
White
second from the right
Black
0 V
Cathode setting voltage:
175 V ±2 (VDC)…34”, 25”, 21”
180 V ±2 (VDC)…29”

http://cxema.ru
– 34 –
KV-XF34K94
RM-962 SECTION 4
CIRCUIT ADJUSTMENTS
Withthe unit on standby
↓
[DISPLAY]
↓
5
↓
VOL (+)
↓
[PO ER]
Thisoperation sequence putsthe unit into service mode.
4-1. ADJUSTMENTS WITH COMMANDER
Service adjustments are made with the RM-962 that comes with
thisunit.
a. ENTERING SERVICE MODE
1, 4Selectthe adjustment item.
↓
3, 6Raise/lowerthe datav alue.
↓
[MUTING] Writes.
↓
-Executesthe writing .
7, -All the data becomes the v alues in memory .
8, -Alluser control goesto the standard state.
5, -Service data initialization (Be sure not to use
usually.)
2, -Write 50Hz adjustment data to 60Hz, or vice
versa.
PAL, SECAM : 50
NTSC : 60
00 HPS 1C SERVICE
Data Mode
Item Name
Item No
Software version
Suffix No
(OEM Code) Total Power-On time (hours)
p
Marking of virgin NVM
GEO
1.0C 59 7F 000A0028S
Device Name
50
RM-962
b. METHOD OF CANCELLATION FROM SERVICE
MODE
Setthe standby condition(Press[PO ER] buttononthe commander),
then press [PO ER] button again, hereupon it becomes TV mode.
c. METHOD OF WRITE INTO MEMORY
1) Set to Service Mode.
2) Press [1] (UP) and [4] (DOWN), select an item of adjustment.
3) Press[MUTING] buttonand it will indicate WRITE on the scr een.
4) Press[0] button to write into memory .
d. MEMORY WRITE CONFIRMATION METHOD
1) After adjustment, pull out the plug fr om AC outlet, and then
pluginto ACoutlet again.
2) Turn the po wer switch ON and set to Ser vice Mode.
3) Calltheadjusteditemsagain toconf irmadjustmentswer emade.
The screen display is :
231
564
897
0
ENTER JUMP
MUTING
MTS VIDEO
PIC
MODE
TV/VIDEO FREEZE SWAP PIP
TV
DISPLAY POWER
CHVOL
MENU
FAVORITE
SURROUND
AUTO PROGR ADD/ERASECABLE
WAKE UP
SOUND
MODE
TV
PIP CH
PIP CH
SLEEP

http://cxema.ru
– 35 –
KV-XF34K94
RM-962
4-2. ADJUSTMENT METHOD
ItemNumber 00of de vice GEO
Thisexplanation uses H-P osition as anexample.
1. Select “GEO 00 HPS” with the 1and 4buttons.
2. Raise/lowerthe data with the 3and 6buttons.
3. Selecttheoptimumstate.(Thestandardis1Ff orPALreception.)
4. Write with the [MUTING] button. (The display changes to
WRITE.)
5. Execute the writing with the -button. (The WRITE
display will be changed to r ed color while excuting, and back
toSERVICE.)
Use the same method for all Items. Use 1and 4to select the
adjustment item, use 3and 6to adjust, write with [MUTING],
then execute the write with -.
Note : 1. In [ RITE],thedataforallitems are written into memory
together.
2. For adjustment itemsthatha vedifferent standard data
between 50Hz or 60Hz, be sur e to use the r espective
inputsignalafteradjustment.
1F SERVICE 50HPS
Adjusted with [3]
and [6] buttons.
GREEN
Written with [MUTING]
Write executed with [0]
GEO 00 7F 0 000A59028S 1.0C
1F SERVICE 50HPS RED
The WRITE display
then the display
returns to a green
SERVICE.
GEO 00 7F 0 000A59028S 1.0C
1F WRITE 50HPS GREEN GEO 00 7F 0 000A59028S 1.0C

http://cxema.ru
– 36 –
KV-XF34K94
RM-962
Adjustment ItemTable
Device Functionality Note Data Range Function Note for Register Slava RAM Address Name No Name Different Data No. (bit) Address (bit) GEO 0 HPS 7 3F H Position 50/60HZ 12 (7-2) CXA2139S(88H) 9A (7-2)
1 HSZ 1F 3F H Size 50/60HZ 11 (7-2) 99 (7-2)
2 PAP 1F 3F Pin Amp 50/60HZ 13 (7-2) 9B (7-2)
3 TLT 7 0F Trapezium 50/60HZ 15 (7-4) 9D (7-4)
4 VPS 1F 3F V Position 50/60HZ 0F (7-2) 97 (7-2) 5 VSZ 1F 3F V Size 50/60HZ 0E (7-2) 96 (7-2)
6 SCO 7 0F S Correction 50/60HZ 10 (7-4) 98 (7-4) 7 VLN 7 0F V Linearity 50/60HZ 10 (3-0) 98 (3-0) 8 BOW 7 0F AFC Bow 50/60HZ 16 (7-4) 9E (7-4) 9 AGL 7 0F AFC-Angle 50/60HZ 16 (3-0) 9E (3-0)
10 UPN 1F 3F Upper Pin 50/60HZ 14 (7-2) 9C (7-2)
11 LPN 2F 3F Lower Pin 50/60HZ 18 (7-2) AO (7-2)
12 HBL 1 1 H Blanking on/off 18 (1) 70 (1) 13 LBL 0F 0F Left H Blanking 50/60HZ 17 (7-4) 9F (7-4)
14 RBL 2 0F Right H Blanking 50/60HZ 17 (3-0) 9F (3-0)
WHB 0 RDR 1F 3F R Drive DYNAMIC/others 09 (7-2) CXA2139S(88H) A7 (7-2)
1 GDR 1F 3F G Drive DYNAMIC/others 0A (7-2) A8 (7-2)
2 BDR 1F 3F B Drive DYNAMIC/others 0B (7-2) A9 (7-2)
3 RCT 7 0F R Cutoff SECAM/others 07 (3-0) AB (3-0) 4 GCT 7 0F G Cutoff SECAM/others 08 (7-4) AC (3-0) 5 BCT 7 0F B Cutoff SECAM/others 08 (3-0) AC (3-0)
6 BMN 15 1F Brightness Minimum Data 06 (7-2) 106
7 SBR 1F 3F Sub Brightness Control 06 (7-2) 107
SAJ 0 PMX 36 3F Picture Maximum Data 03 (7-2) CXA2139S(88H) 105
1 SHU 8 0F Sub Hue Control TV/Video 05 (7-2) 108 2 SSH 8 0F Sub Sharpness Control TV/Video 07 (7-4) 109
3 SCL 1F 3F Sub Color Control NTSC/others 04 (7-2) 10A
VP 0 EHT 5 0F EHT Comp 50/60HZ 15 (3-0) CXA2139S(88H) 9D (3-0)
1 GMA 2 03 Gamma Correction (Separated in NTSC/others 0B (1-0) 368 (1-0)
STANDARD mode)
2 YDL 0D 0F Y Delay PAL/SECAM/ 0C (3-0) 36B (3-0)
NTSC/DVD
3 SST 1 03 SECAM ID Start Position 1B (1-0) 73 (1-0) 4 SSP 1 03 SECAM ID Stop Position 1B (3-2) 73 (3-2) 5 SLV 2 03 SECAM ID Level 1C (1-0) 74 (1-0) 6 SBF 22 3F SECAM BELL fO 1C (7-2) 74 (7-2) 7 DYC 1 1 Dynamic Color on/off 0A (1) 62 (1)
8 ABL 1 1 ABL Mode Switching (except except STANDARD 09 (1) 61 (1)
STANDARD mode)
9 VTH 1 1 ABL Detection Vth Switching 09 (0) 61 (0)
10 SFO 1 1 FO Switching for Sharpness NTSC/others 05 (1) 359 (1) 11 DCX 1 1 DC Trans.Ratio Switching 06 (1) 5E (1) 12 SHT 1 1 Pre-/Overshoot ratio Switch NTSC/others 06 (0) 35A (0)

http://cxema.ru
– 37 –
KV-XF34K94
RM-962
Adjustment ItemTable
Device Functionality Note Data Range Function Note for Register Slava RAM Address Name No Name Different Data No. (bit) Address (bit) VP 13 HDW 0 1 H Drive Pulse Width Switch 00 (6) 58 (6)
14 AFC 1 03 AFC Gain Control TV/Video 0F (1-0) A5 (1-0)
15 HOS 7 0F H Oscillation 0C (7-4) 64 (7-4) 16 HSS 0 1 Slice Level of H Sync Sep. 0D (1) 65 (1) 17 VSS 0 1 Slice Level of V Sync Sep. 0D (0) 65 (0)
18 HMS 1 1 Macro Vision C/m off/on 50/60Hz 0E (0) 96 (0) 19 YUV 0 1 YUV Switch Control 01 (0) 59 (0) 20 CDV 1 3 CD mode for Video and RF Video only 0D (5-4) 366 (5-4)
under no signal
21 RON 1 1 R ON not memorized 01 (3) 59 (3)
22 GON 1 1 G ON not memorized 01 (2) 59 (2)
23 BON 1 1 B ON not memorized 01 (1) 59 (1) 24 PON 1 1 P ON not memorized 00 (7) 58 (7) 25 BLK 0 1 BLK Off 12 (0) 6A (0)
26 VMC 0 1 VM Off 13 (0) 6B (0)
AP 0 BCS 2 3 Bass Center Shift #4 (3-0) TDA7315(80H) 35B (1-0)
1 TCS 1 3 Treble Center Shift #5 (3-0) 35C (1-0)
2 TRF 2 3 RF Treble Offset #5 (3-0) 365 (1-0)
MSP 0 WST 15 FF W/G Stereo Threshold MSP3415D(84H) 165
1 WBT EC FF W/G Bilingual Threshold 166 2 WLL 5 FF W/G Monaural Threshold 167 3 WAC 1 0F W/G Agreement Count 168 4 WDL 30 FF W/G Search Delay 169
5 NDL 20 FF NICAM Search Delay 16A
6 SDL 10 FF Stereo status Read Delay 16B 7 AGC 1 1 AGC Switch Auto/Constant 00BB (7) 116 (7) 8 REL 28 3F AGC Gain at Constant Mode 00BB (6-1) 116 (6-1) 9 CRM 0 1 Carrier muting on/off 00BB (9) 115 (9)
10 ACO 1 1 Audio Clock out on/off 0083 (5) 11A (5)
11 FP 1B 7F FM Prescale for non-M system 000E (14-8) 32F
12 FPM 32 7F FM Prescale for M system 000E (14-8) 330 13 FH 36 7F FM Prescale for HDEV 000E (14-8) 331 14 FHM 65 7F FM Prescale for HDEV and M 000E (14-8) 332 15 WGP 1C 7F W/G Prescale 000E (14-8) 333 16 NIP 7F 7F NICAM Prescale 0010 (14-8) 14F
17 ERR 50 FF Auto FM switch Threshold 0021 (10-3) 174
18 VOL 6D FF Loud Speaker gain 7000h TO 7FF0H 0000 (11-4) 361