Sony KV-XS29M31 User manual

http://cxema.ru
MODEL COMMANDER DEST. CHASSIS NO.
KV-XS29M31 RM-954 New Zealand SCC-U26E-A
KV-XS29M33 RM-954 Australia SCC-U23C-A
KV-XS29M39 RM-953 New Zealand SCC-U26C-A
KV-XS29M50 RM-954 Malaysia SCC-U21K-A
KV-XS29M50 RM-954 GE SCC-U12R-A
KV-XS29M60 RM-954 Thailand SCC-U18K-A
KV-XS29M63 RM-954 Thailand SCC-U18J-A
CHASSIS
TRINITRON ® COLOR TV
SERVICE MANUAL BG-3S
(RM-953) (RM-954)
MODEL COMMANDER DEST. CHASSIS NO.
KV-XS29M65 RM-954 Malaysia SCC-U21J-A
KV-XS29M69 RM-953 Singapore SCC-U2AE-A
KV-XS29M87 RM-953 ME SCC-U30Q-A
KV-XS29M89 RM-953 ME SCC-U30N-A
KV-XS29M93 RM-954 Hong Kong SCC-U17M-A

http://cxema.ru
– 2 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
Note
Power requirements 110-240V AC, 50/60 Hz KV-XS29M50(GE)/M69/M87
220-240 V AC, 50/60 Hz Except KV-XS29M50(GE)/M69/M87
Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K, M
Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58
Stereo system NICAM Stereo B/G, I; A2 Stereo (German) B/G
Teletext Language English, French, Arabic KV-XS29M65/M69/M89
Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41
IUHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
MVHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 toA-2, A to W+4, W+6 to W+84
˘(Antenna) 75-ohm external terminal
Audio output 6W + 6W KV-XS29M63/M65/M69/M87/M89/M93
8W + 8W KV-XS29M50/M60
3D WOOFER 15W KV-XS29M63/M65/M69/M87/M89/M93
Number of terminal
D(Video) Input: 3 Output: 1 Phono jacks; 1 VP-P, 75 ohms
Input: 4 Output: 1 Phono jacks; 1 VP-P, 75 ohms KV-XS29M63 only
≥(Audio) Input: 3 Output: 1 Phono jacks; 500 mVrms
Input: 4 Output: 1 Phono jacks; 500 mVrms KV-XS29M63 only
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync negative
C : 0.286 Vp-p, 75 ohms
(Component Input: 1 Phono jacks:
Video) Y : 1.0 Vp-p, 75 ohms,
sync negative
CB: 0.7 Vp-p, 75 ohms
CR: 0.7 Vp-p, 75 ohms
Audio : 500 mVrms KV-XS29M63/M65/M69/M87/M89/M93
2(Headphone) Output: 1 Minijack
Picture tube 29 inch
Tube size (cm) 72 Measured diagonally
Screen size (cm) 68 Measured diagonally
Dimensions (w/h/d, mm) 794 ×573 ×517 KV-XS29M50/M60
794 ×589 ×517 KV-XS29M63/M65/M69/M87/M89/M93
Mass (kg) 51 KV-XS29M50/M60
54 KV-XS29M63/M65/M69/M87/M89/M93
Design and specifications are subject to change without notice.
SPECIFICATIONS
(Except KV-XS29M31/XS29M33/XS29M39)
SAFETY-RELA TED COMPONENT WARNING!!
COMPONENTSIDENTIFIEDBYSHADINGANDMARK !ON
THESCHEMA TICDIA GRAMS, EXPLODED VIEWSANDIN THE
PARTSLISTARECRITICAL TOSAFEOPERA TION. REPLA CE
THESECOMPONENTS WITHSONYP ARTS WHOSE P ART
NUMBERS APPEAR AS SHO WN IN THIS MANU AL OR IN
SUPPLEMENTSPUBLISHEDBYSONY .
CAUTION
SHOR TCIRCUIT THEANODEOF THEPICTURE TUBEAND
THEANODECAP TO THEMET ALCHASSIS, CR TSHIELD ,OR
CARBONP AINTED ON THECR T, AFTER REMO VING THE
ANODE.

http://cxema.ru
– 3 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
SPECIFICATIONS
(KV-XS29M31/XS29M33/XS29M39) Note
Power requirements 220-240 V AC, 50/60 Hz
Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K, M
Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58
Stereo/ Bilingual system NICAM Stereo/ Biligual B/G, I; A2 Stereo/ Bilingual (German) B/G KV-XS29M31/M33/M39
Teletext Language English, French, Arabic KV-XS29M31/M39
Channel coverage
B/G
VHF: 0 to 12, 5A, 19A / UHF: 28 to 69 / CATV: S01 to S03, S1 to S41 KV-XS29M33 only
VHF: 1 to 11 / UHF: 21 to 69 / CATV: S01 to S03, S1 to S41 KV-XS29M31/M39
IUHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
MVHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘(Antenna) 75-ohm external terminal
Audio output 6W + 6W KV-XS29M33/M39
8W + 8W KV-XS29M31 only
3D WOOFER 15W KV-XS29M33/M39
Number of terminal
D(Video) Input: 3 Output: 1 Phono jacks; 1VP-P, 75 ohms
≥(Audio) Input: 3 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync
negative
C : 0.286 Vp-p, 75 ohms
(Component Input: 1 Phono jacks: KV-XS29M33/M39
Video) Y : 1.0 Vp-p, 75 ohms,
sync negative
CB: 0.7 Vp-p, 75 ohms
CR: 0.7 Vp-p, 75 ohms
Audio : 500 mVrms
2(Headphone) Output: 1 Minijack
Picture tube 29 inch
Tube size (cm) 72 Measured diagonally
Screen size (cm) 68 Measured diagonally
Dimensions (w/h/d, mm) 794 ×589 ×517 KV-XS29M33/M39
794 ×573 ×517 KV-XS29M33/M39
Mass (kg) 51 KV-XS29M31 only
54 KV-XS29M33/M39
Design and specifications are subject to change without notice.
SAFETY-RELA TEDCOMPONENT WARNING!!
COMPONENTSIDENTIFIEDBYSHADINGANDMARK !ON
THESCHEMA TICDIA GRAMS, EXPLODED VIEWSANDIN THE
PARTSLISTARECRITICAL TOSAFEOPERA TION. REPLA CE
THESECOMPONENTS WITHSONYP ARTS WHOSE P ART
NUMBERS APPEAR AS SHO WN IN THIS MANU AL OR IN
SUPPLEMENTSPUBLISHEDBYSONY .
CAUTION
SHOR TCIRCUIT THEANODEOF THEPICTURE TUBEAND
THEANODECAP TO THEMET ALCHASSIS, CR TSHIELD ,OR
CARBONP AINTED ON THE CR T, AFTER REMO VING THE
ANODE.

http://cxema.ru
– 4 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
TABLE OF CONTENTS
Section Title Page
SELF DIAGNOSIS FUNCTION................................ 5
1. GENERAL........................................................................ 9
2. DISASSEMBLY
2-1. 3D Speaker Box Removal ....................................... 47
2-2. Rear Cover Removal ................................................ 47
2-3. Speaker Removal ..................................................... 47
2-4. Chassis Assy Removal ............................................. 47
2-5. F Bracket Removal .................................................. 48
2-6. Service Position ....................................................... 48
2-7. Replacement of Parts ............................................... 48
2-7-1. Replacement of Control Button ..................................... 48
2-7-2. Replacement of Light Guide .......................................... 48
2-8. D3 Board Removal .................................................. 49
2-9. PWB Holder Removal ............................................. 49
2-10. Terminal Bracket Removal ...................................... 49
2-11. P2, B5 and B7 Boards Removal .............................. 49
2-12. H5 Board Removal .................................................. 50
2-13. A and B3 Boards Removal ...................................... 50
2-14. Picture Tube Removal.............................................. 50
3. SET-UP ADJUSTMENTS
3-1. Beam Landing.......................................................... 52
3-2. Convergence............................................................. 53
3-3. Focus Adjustment .................................................... 55
3-4. G2 (Screen) and White BalanceAdjustments......... 56
4. CIRCUIT ADJUSTMENT
4-1. Adjustments with Commander ................................ 57
4-2. Adjustment Method ................................................. 58
4-3. Picture Quality Adjustments.................................... 64
4-4. A Board Adjustment After IC003 (Memory)
Replacement............................................................. 64
4-5. Picture Distortion Adjustment ................................. 65
Section Title Page
5. DIAGRAMS
5-1. Block Diagram ......................................................... 67
5-2. Frame Schematic Diagram ...................................... 71
5-3 Circuit Boards Location .......................................... 75
5-4. Schematic Diagrams and Printed Wiring Boards ... 75
(1) Schematic Diagram of A (1/2) Board...................... 81
(2) Schematic Diagram of A (2/2) Board...................... 85
(3) Schematic Diagram of B3 Board ............................ 89
(4) Schematic Diagrams of B5 and B7 Boards............. 93
(5) Schematic Diagram of C Board .............................. 97
(6) Schematic Diagram of P2 Board ............................ 101
(7) Schematic Diagram of D3 Board ........................... 104
(8) Schematic Diagram of H5 Board ........................... 107
(9) Schematic Diagram of VM1 Board........................ 111
(10) Schematic Diagrams of F and J4 Boards ............... 113
5-5. Semiconductors....................................................... 116
6. EXPLODEDVIEWS
6-1. Speaker Bracket ...................................................... 119
6-2. Chassis .................................................................... 120
6-3. Picture Tube ............................................................ 121
6-4. 3D Speaker .............................................................. 122
7. ELECTRICAL PARTS LIST...................................... 123

http://cxema.ru
– 5 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1. DIAGNOSTICTEST INDICATORS
When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic
Item
Description
• Power does not
turn on
• +B overcurrent
(OCP) or
overvoltage
(OVP)
• Vertical deflection
stopped
• Horizontal
deflection
overdrive
• White balance
failure (no
PICTURE)
• Micro reset
Detected
Symptoms
• Power does not come on.
• No power is supplied to the
TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is
shorted.
• Has entered standby state
after horizontal raster.
• Vertical deflection pulse is
stopped.
• Power line is shorted or
power supply is stopped.
• No raster is generated.
• CRT cathode current
detection reference pulse
output is small.
• Power is shut down shortly,
after this return back to
normal.
• Detect Micro latch up.
Note 1: If a + B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously.
The symptom that is diagnosed first by the microcontroller is displayed on the screen.
Note 2: Refer to screen (G2) Adjustment in section 3-4 of this manual.
SELF DIAGNOSTIC FUNCTION
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
5 times
—
Self-diagnostic
display/Diagnostic
result
—
002:000 or
002:001~255
003:001~255
004:001~255
at the same time
005:000 or
005:001~225
101:00 or
101:001~225
Probable
Cause
Location
• Power cord is not plugged
in.
• Fuse is burned out F4601
(F)
• H.OUT Q511 is shorted.(A
board)
• IC701 is shorted. (C board)
• -13V is not supplied. (A
board)
• IC 503 faulty (A board)
• G2 is improperly adjusted.
(Note 2)
• CRT problem.
• Video OUT IC701 is faulty.
(C board)
• IC301 is faulty. (A board)
• No connection A board to C
board.
• Discharge CRT (C Board)
• Static discharge
• External noise

http://cxema.ru
– 6 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
Diagnostic Item Flash Count*
+B overcurrent/overvoltage 2 times
Vertical deflection stopped
White balance failure 5 times
* One flash count is not used for self-diagnostic.
3. STOPPINGTHE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.
Lamp ON 0.3 sec. Lamp OFF 3 sec.
Lamp OFF 0.3 sec.
2 times
5 times
STANDBY/SLEEP lamp

http://cxema.ru
– 7 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screendisplay] /channel [5] /Sound volume [-] /Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
002 : 000
003 : 000
004 : 000
005 : 001
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
101 : 000
SELF DIAGNOSTIC
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel [8] /0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.

http://cxema.ru
– 8 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
6. SELF-DIAGNOSTIC CIRCUIT
[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q604. If Q604 go to ON
and the voltage to pin 18 of IC301 should go down when V.SYNC is more than seven
verticals in a period, the unit will automatically turn off.
[Verticaldeflectionstopped] Occurs when an absence of the vertical deflection pulse is detected by Q509 and IC001
shut down the power supply.
[Verticaldeflectionovercurrent] Occurs when an overcurrent on V drive line is detected by Q507. Power supply will be
shut down when detect this by IC001.
[ hitebalancefailure] If the RGB levels* do not balance or become low level within 5 seconds, this error will be
detected by IC301.TV will stay on, but there will be no picture.
* (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.)
IC301
Y/CHROMA JUNGLE
FROM
CRT
FROM
[+B] Q604 C
[V] Q509/507
IC001
SYSTEM IC003 MEMORY
B-DAT
IO-SDAT
IK-IN
MP/
PROTECT
IO-8DAT
O-LED
SDA
54521
18 51
4635

http://cxema.ru
– 9 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
SECTION 1-1
GENERAL
(KV-XS29M39/M69/M87/M89)
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
2
WARNING
• Dangerously high voltages are present inside the TV.
•
TV operating voltage: 110 – 240 V AC ( or New Zealand and Australia only: 220 – 240 V AC).
To prevent fire or shock hazard, do not expose
the TV to rain or moisture.
Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by
qualified personnel only.
Do not open the cabinet and the rear cover of the
TV. Refer servicing to qualified personnel.
Do not install the TV in hot, humid or excessively
dusty places.
Do not install the TV in a confined space, such
as a bookcase or built-in cabinet.
Do not block the ventilation openings of the TV.
Pull the power cord out by the plug. Do not pull
the power cord itself. Disconnect the TV if you
are not going to use it for several days.
Install the TV in a stable position. Do not allow
children to climb onto it.
Do not plug in too many appliances to the same
power socket. Do not damage the power cord.
Clean the TV with a dry and soft cloth.
Do not use benzine, thinner, or any other chemicals
to clean the TV. Do not scratch the picture tube.
or your own safety, do not touch any part of the
TV, the power cord and the antenna cable during
lightning storms.
4
Using Your New TV
VIDEO
VIDEO IN
VIDEO OUT
AUDIO
R L
WOOFER
123
L
(MONO)
R
RLY C
B
C
R
Getting Started
Step 1
Connect the antenna
If you wish to connect a VCR, see the “Connecting a VCR” diagram below.
CAUTION
Do not connect the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
Connecting a VCR
To watch the video, press … (see page 11).
IEC connector
(not supplied)
To video and
audio outputs
VCR
(yellow)
- (MONO) (white) -R (red)
To S video
output
Antenna cable (not supplied)
To … 1, 2 or 3
(video input)
Audio/Video cable
(not supplied)
S video cable
(not supplied)
: Signal flow
To
(S video input)
To antenna
output
To ˘
(antenna)
or
: Signal flow
Antenna cable (not supplied)
Antenna cable (not supplied)
Rear of TV
Rear of TV
Using Your New TV

http://cxema.ru
– 10 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
5
Using Your New TV
Using Your New TV
Front of TV
1
2
Notes
• If you connect a monaural VCR, connect the yellow plug to (the
yellow jack) and the black plug to -L (MONO) (the white jack).
• If you connect a VCR to the ˘ (antenna) terminal, preset the signal
output from the VCR to the program number 0 on the TV.
• If both (S video input) and … 1 (video input) at the rear of your TV
are input at the same time, the (S video input) is automatically
selected. To view … 1 (video input), disconnect the S video cable.
• Do not connect video equipment to … 3 (video input) at the front and
the rear of your TV at the same time; otherwise the picture will not be
displayed properly on the screen.
• When no signal is input to the connected video equipment, the TV screen
becomes blue.
Step 2
Insert the batteries
into the re ote
Note
• Do not use old batteries nor use different types of batteries together.
Step 3
Preset the channels auto atically
Tips
• If you want to stop the automatic channel presetting, press MENU twice.
• If your TV has preset an unwanted channel or cannot preset a particular
channel, then preset your TV manually (see page 30).
Note (KV-XS29M89/M87 only)
• During automatic channel presetting, your TV screen will indicate “B/G”,
“I”, “D/K” or “M” for the TV system (“TV SYS”).
6
Using Your New TV
WOOFER
(8)
123
L
(MONO)
R
R L Y C
B
C
R
3D WOOFER
Rear of TV
1
2
Black wire
Red wire
Connecting the 3D WOOFER
1
Attach the 3D WOOFER into the ootholds on the top o your TV.
2
Connect the wires to the 3D WOOFER (8Ω) terminals at the rear o your TV.
The red wire should be connected to the ‘ red terminal and the black wire
to the ’ black terminal.
Notes
• Connect only the supplied 3D WOO ER; otherwise your TV may
malfunction.
• Unplug your TV from the wall outlet when connecting the 3D WOO ER.
• To prevent a malfunction caused by a short circuit of the terminals, make
sure that none of the 3D WOO ER wire strands stick out, making contact
with the neighbouring speaker terminal.
You can enjoy high quality sound by connecting the 3D WOO ER.

http://cxema.ru
– 11 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
8
Using Your New TV
Notes
• Some DVD player terminals may be labeled differently:
• Since the high quality pictures on a DVD disc contain a lot of information,
picture noise may appear. In this case, adjust the sharpness (“SHARP”) in the
“ADJUST” menu of the “PICTURE MODE” menu (see page 25).
• Connect your DVD player directly to your TV. Connecting the DVD player
through other video equipment will cause unwanted picture noise.
Connecting a DVD player using the (co ponent
video input) jacks
1 Connect R and L under (component video input) on your TV to the LINE OUT,
AUDIO R and L output connectors on your DVD player.
2 Using a component video cable, connect Y, C
B
, and C
R
under (component video
input) on your TV to the COMPONENT VIDEO OUT Y, C
B
, and C
R
output
connectors on your DVD player.
DVD player
To
(white)
R (red)
Audio cable
(not supplied)
To component
video output
Component video cable
(not supplied)
To audio
output
: Signal flow
To
(component
video input)
Connect To (on the DVD player)
Y (green) Y
C
B
(blue) C
b
, B-Y or P
B
C
R
(red) C
r
, R-Y or P
R
VIDEO
R-AUDIO-L
LINE OUT
Y
COMPONENT VIDEO OUT
S VIDEO OUT
C
B
C
R
RLYC
B
C
R
Connecting optional components (continued)
Rear of TV
Connecting a DVD player using the … (video input) jacks
VIDEO
R-AUDIO-L
LINE OUT
123
L
(MONO)
R
DVD player
Audio/Video cable
(not supplied)
(yellow)
- (MONO) (white) -R (red)
To … 1, 2, or 3
(video input)
: Signal flow
Rear of TV
7
Using Your New TV
Using Your New TV
Connecting optional co ponents
You can connect optional audio/video components, such as a VCR, multi disc player,
DVD, camcorder, video game or stereo system. To watch the picture of the connected
equipment, press … (see page 11).
Connecting a ca corder/video ga e equip ent
using the … (video input) jacks
Notes
• You can also connect video equipment to the … 1, 2 or 3 (video input)
jacks at the rear of your TV.
• If both (S video input) and … 3 (video input) at the front of your TV
are input at the same time, the (S video input) is automatically
selected. To view … 3 (video input), disconnect the S video cable.
• Do not connect video equipment to the … 3 (video input) jacks at the
front and the rear of your TV at the same time; otherwise the picture will
not be displayed properly on the screen.
Connecting audio/video equip ent using the Ú
( onitor output) jacks
Note
• If you select “DVD” on your TV screen, no signal will be output at the Ú
(monitor output) jacks (see page 11).
To S video output
Front of TV
Camcorder
Video game
equipment
To video and
audio outputs
(yellow)
- (MONO)
(white)
-R (red)
Rear of TV
To
antenna
output
To video and
audio inputs
or
Audio system
To
audio
inputs
VCR
: Signal flow
: Signal flow
To
(S video
input)
To … 3 (video input)
To Ú
(monitor
output)
or
Audio/Video cable (not supplied)
S video cable (not supplied)
Antenna cable (not supplied)
Audio/Video cable
(not supplied)
(MONO)
WOOFER
123
L(MONO)
R
RLYC
B
C
R
continued

http://cxema.ru
– 12 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
9
Using Your New TV
Using Your New TV
Securing the TV
To prevent the TV from falling, secure the TV using one of the following methods:
A
With the supplied screws, attach the band to the TV stand and to the rear o
the TV using the provided hole.
or
B
Put the cord or chain through the clamps to secure the TV against a wall or
pillar.
Note
• Use only the supplied screws. Use of other screws may damage the TV.
20
mm
AB
3.8 mm
or
10
Using Your New TV
Watching the TV
This section explains functions used
while watching TV. Most operations can
be done using the remote.
1
Press U to turn on the TV.
When the TV is in the
standby mode (the u
indicator on the TV is lit
red), press u on the remote
or PROGR +/– on the TV.
2
Press PROGR +/– or
number buttons to select
the TV program.
or double digit numbers,
press ÷, then the number
(e.g., for 25, press ÷, then
2 and 5).
To select a TV program quickly
(1) Press and hold PROGR +/–.
(2) Release PROGR +/– when the desired program number appears.
Note
• When you select a TV program quickly, the picture may be disrupted.
This does not indicate a malfunction.
¤
u
…
;
Number buttons
JUMP
. +/–
PROGR +/–
MENU
V/b/v/B/ENTER
or
u indicator
123
456
78
0
-/--
9
123 456
78
0
-/--
9
FAVORITE
SOUND
MODE SURROUND
PIP PROGR
PIP PROGR
ENTER
PIC MODE

http://cxema.ru
– 13 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
11
Using Your New TV
Using Your New TV
To
Turn off temporarily
Turn off completely
Adjust the volume
Mute the sound
Watch the video input
(VCR, camcorder, etc.)
Jump back to the previous channel
Display the on-screen information*
Do this
Press u. The u indicator on the TV lights up red.
Press U on the TV.
Press . +/–.
Press ¤.
Press
…
to select “VIDEO 1”, “VIDEO 2” , “VIDEO 3”or
“DVD”.
To return to the TV program, press ;.
Press JUMP.
Press .
Additional tasks
ENTER
To return to the normal screen
Press MENU.
ENTER ENTER
ENTER ENTER
continued
‡]'w
£´Œ¡GPR01 ˆ
·…fl › ¶q––¤ ¡Gˆ
–‘¥˛ W„D
„ˇ„‡–´«‰‚ß
»y¤¥¡ LANGUAGE¡G⁄⁄⁄
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information
disappears after about 3 seconds.
Changing the enu language (KV-XS29M69 only)
You can change the menu language as well as the on-screen language.
or details on how to use the menu, see “Introducing the menu system” on page 22.
1
Press MENU.
2
Press V or v to select the
“SET UP” icon ( ),
then press ENTER.
3
Make sure “LANGUAGE”
is selected, then press
ENTER.
4
Press V or v to select the
desired language (e.g.,
“”), then press
ENTER.
The selected menu language appears.
+
11
Using Your New TV
Using Your New TV
To
Turn off temporarily
Turn off completely
Adjust the volume
Mute the sound
Watch the video input
(VCR, camcorder, etc.)
Jump back to the previous channel
Display the on-screen information*
Do this
Press u. The u indicator on the TV lights up red.
Press U on the TV.
Press . +/–.
Press ¤.
Press
…
to select “VIDEO 1”, “VIDEO 2” , “VIDEO 3”or
“DVD”.
To return to the TV program, press ;.
Press JUMP.
Press .
Additional tasks
ENTER
To return to the normal screen
Press MENU.
ENTER ENTER
ENTER ENTER
continued
* The picture, sound, and either the program number or video mode are
displayed. The on-screen display for the picture and sound information
disappears after about 3 seconds.
Changing the enu language (Except KV-XS29M69)
You can change the menu language as well as the on-screen language.
or details on how to use the menu, see “Introducing the menu system” on page 22.
1
Press MENU.
2
Press V or v to select the
“SET UP” icon ( ),
then press ENTER.
3
Make sure “LANGUAGE”
is selected, then press
ENTER.
4
Press V or v to select
the desired language
(e.g., “ ”), then
press ENTER.
The selected menu language appears.
+

http://cxema.ru
– 14 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
12
Using Your New TV
Setting the Wake Up ti er
1
Press until the desired
period o time appears.
The Wake Up timer starts
immediately after you
have set it.
2
Select the TV program or video mode you want to display when you wake
up.
3
Press u or set the Sleep timer i you want the TV to turn o automatically.
The indicator lights up orange.
To cancel the Wake Up timer
Press until “WAKE UP TIMER: O ” appears or turn off the TV’s
main power.
Note
• If no buttons or controls are pressed for more than two hours after the TV
is turned on using the Wake Up timer, the TV automatically goes into the
standby mode. To continue watching the TV, press any button or control
on the TV or the remote.
Setting the Sleep ti er
Press until the desired
period o time appears.
The Sleep timer starts
immediately after you
have set it.
To cancel the Sleep timer
Press until “SLEEP TIMER: O ” appears or turn the TV off.
WAKE UP TIMER:10M
WAKE UP TIMER:OFF
After 10 minutes
No Wake Up Timer
WAKE UP TIMER:12H00M
After 12 hours
SLEEP TIMER:30M SLEEP TIMER:60M
SLEEP TIMER:OFF SLEEP TIMER:90M
After 30 minutes
No Sleep Timer
After 60 minutes
After 90 minutes
Watching the TV (continued)
13
Advanced Operations
SOUND MODE
PIC MODE
Selecting the
picture and sound
odes
You can select picture and sound modes
and adjust the setting to your preference
in “PERSONAL” option.
Selecting the picture ode
Press PIC MODE
repeatedly until you get
the desired picture mode.
Select To
“DYNAMIC” receive high contrast pictures.
“STANDARD” receive normal contrast pictures.
“SO T” receive mild pictures.
“PERSONAL” receive the last adjusted picture setting from the “ADJUST”
option in the “A/V CONTROL” menu (see page 24).
Selecting the sound ode
Press SOUND MODE
repeatedly until you get
the desired sound mode.
Select To
“DYNAMIC” listen to dynamic and clear sound that emphasizes the low and
high tones.
“DRAMA” listen to sound that emphasizes voice and high tones.
“SO T” receive soft sound.
“PERSONAL ” receive the last adjusted sound setting from the “ADJUST”
option in the “A/V CONTROL” menu (see page 24).
Tip
• You can also set the picture and sound modes using the menu (see
“Changing the “A/V CONTROL” setting” on page 24).
PERSONAL SOFT
STANDARD
DYNAMIC
≥
DYNAMIC
≥
DRAMA
≥
SOFT
≥
PERSONAL
PIC MODE
Advanced Operations
Advanced Operations

http://cxema.ru
– 15 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
14
Advanced Operations
1
1
Press FAVORITE.
2
Press the number button
rom 1 to 6 to select the
desired channel.
Tip
• To program your favorite channels, see “Programming your favorite
channels” on page 28.
Viewing your
favorite channels
You can display and select six of your
favorite channels directly from your TV
screen. Number buttons
FAVORITE
123
456
123
456
78
0
-/--
9
FAVORITE
SOUND
MODE SURROUND
PIP PROGR
PIP PROGR
ENTER
PIC MODE
15
Advanced Operations
Watching two
progra s at the
sa e ti e
— PIP
With the Picture-in-Picture (PIP) feature,
you can display a different TV program
or video directly within the main
picture.
Displaying the PIP screen
Press .
///
V/v
123
456
78
0
-/--
9
FAVORITE
SOUND
MODE SURROUND
PIP PROGR
PIP PROGR
ENTER
PIC MODE
continued

http://cxema.ru
– 16 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
16
Advanced Operations
Additional PIP tasks
To
change a TV program in the PIP screen
change a video input in the PIP screen
swap pictures between the main
and PIP screens
freeze the PIP screen
To return to the normal screen
Press .
Tips
• You can also display the PIP screen using the menu (see “Changing the
PIP setting” on page 26).
• You can change the position of the PIP screen (see “Changing the PIP
setting” on page 26).
Notes
• When you display a video input on the PIP screen at a faster/slower
speed, the picture may be disrupted depending on the VCR type.
• If you display different color systems on the PIP screen, the size of the PIP
screen may be different and the picture may be disrupted. This does not
indicate a malfunction of the TV.
Press
V (PIP PROGR +) or v (PIP PROGR –).
.
.
.
To unfreeze the screen, press the button again.
Watching two programs at the same time—PIP (continued)
17
Advanced Operations
Press SURROUND
repeatedly until you
receive the desired
surround sound.
Select To
“HIGH” listen to sound that spreads out over a large area, giving the feeling
of being at a concert hall.
“LOW” listen to the sound that gives the feeling of being at a live concert.
“O ” turn off the surround sound.
The surround of your TV is categorized as TruSurround.
TM
is a trademark of SRS Labs, Inc. SRS and the SRS symbol are
registered trademarks of SRS Labs, Inc. in the United States and selected foreign
countries. SRS and TruSurround are incorporated under license from SRS Labs,
Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572
with numerous additional issued and pending foreign patents.
Listening with
surround sound
The surround feature enables you to
enjoy the sound effects of a concert hall
or movie theater.
FAVORITE
SOUND
MODE SURROUND
PIP PROGR
PIP PROGR
ENTER
SURROUND: LOW
SURROUND: HIGH
SURROUND: OFF
SURROUND

http://cxema.ru
– 17 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
18
Advanced Operations
123
456
78
0
-/--
9
PIC MODE
Broadcasting On-screen display (Selected sound)
NICAM stereo
NICAM bilingual
NICAM monaural
Enjoying stereo
or bilingual
progra s
(KV-XS29M39/M69)
You can enjoy stereo sound or bilingual
programs of NICAM and A2 (German)
stereo systems.
Press A/B repeatedly until
you receive the sound you
want.
The on-screen display changes
to show the selected sound
and the  indicator on the TV
lights up red.
When receiving a NICAM program
A/B
NICAM MONO
(Stereo sound) (Regular sound)
NICAM
MAIN MONO
(Main sound) (Regular sound)
NICAM
SUB
(Sub sound)
NICAM
MAIN MONO
(Main sound) (Regular sound)
19
Advanced Operations
MONO AUTO
System
NICAM
A2 (German)
When receiving an A2 (German) program
Receiving area for NICAM and A2 (German) programs
Notes
• If the signal is very weak, the sound becomes monaural automatically.
• If the stereo sound is noisy when receiving a NICAM program, select
“MONO”. The sound becomes monaural, but the noise is reduced.
If the sound is distorted or noisy when receiving a monaural
program through the ˘ (antenna) terminal
Press A/B repeatedly until “MONO” appears on the screen.
To cancel the monaural sound setting, press A/B again until
“AUTO” appears on the screen.
Notes
• The “MONO” or “AUTO” setting is memorized for each program
position.
• You cannot receive stereo broadcast signal when the TV is in the “MONO”
setting. Normally set the TV to “AUTO”.
STEREO
MONO
(Stereo sound)
(Regular sound)
MAIN SUB
(Main sound) (Sub sound)
Broadcasting On-screen display (Selected sound)
A2 (German) stereo
A2 (German) bilingual
Receiving area
New Zealand, Hong Kong, Singapore, Malaysia,
Thailand, etc.
Australia, Malaysia, Thailand, etc.

http://cxema.ru
– 18 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
20
Advanced Operations
Viewing Teletext
(KV-XS29M39/M69)
TV stations broadcast an information
service called Teletext via some TV
channels. Teletext allows you to receive
various information, such as shares
market or news.
Displaying Teletext
1
Select a TV channel that carries the Teletext broadcast you want to watch.
2
Press to display the
text.
A Teletext page (normally
the index page) is
displayed. If there is no
Teletext broadcast, “100” is
displayed at the top left
corner of the screen.
To turn off Teletext
Press ;.
…
b
;
P166 SECTEXT 166 FR1 MAR 03:59:09 From Singapore To PAR IS To OSAKA To ROMA To SYDNEY
Day Dep/Arr Flight Alrcraft
1.6 220/0588 SQ28 747
2 2130/1225 PA115 L15 3 2115/1330 SQ26 747 2.7 2130/0745 SQ24
747
4 2300/0915 AZ487 747 2.5 1000/1715 SQ6 747 4.6 0930/2015 CX522 L10 1 2210/0610 SQ21A 747 2 2100/0835 SQ21A 747
A/B
123
456
78
0
-/--
9
FAVORITE
SOUND
MODE SURROUND
PIP PROGR
PIP PROGR
ENTER
PIC MODE
21
Advanced Operations
Additional Teletext tasks
To
display a Teletext page on the TV
picture
check the contents of a Teletext service
select a Teletext page
hold a Teletext page
(stop the page from scrolling)
reveal concealed information
(e.g., an answer to a quiz)
enlarge the Teletext display
wait for a Teletext page while watching
a TV program
* You can also select a Teletext page of any page number that appears in the
colored column at the bottom of the screen using the corresponding color-
coded button on the remote.
Using FASTEXT
This feature allows you to quickly access a Teletext page that uses
ASTEXT. When a ASTEXT program is broadcasted, the colored
menus appear at the bottom of the screen. The colors of the menus
correspond to the red, green, yellow, and blue color-coded buttons
on the remote.
To access a FASTEXT menu
Press the color-coded button on the remote corresponding to the
menu you want. The menu page appears on the screen after several
seconds.
Do this
Press .
Each time you press , the screen changes as
follows: Teletext n Teletext and TV n TV.
Press
.
An overview of the Teletext contents and page
numbers appear on the screen.
Press the number buttons to enter the three-digit
page number of the desired Teletext page.* If you
make a mistake, reenter the correct page number. To
access the next or previous page, press PROGR +/–.
Press to display the symbol “j” at the top left
corner of the screen. To resume normal Teletext
operation, press
or .
Press .
To conceal the information, press the button again.
Press .
Each time you press , the Teletext display
changes as follows: Enlarge upper half n Enlarge
lower half n Normal size.
1 Enter the Teletext page number that you want to
refer to, then press .
2 When the page number is displayed, press to
show the text.

http://cxema.ru
– 19 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
20
Adjusting Your Setup (MENU)
Introducing the enu syste
The MENU button lets you open a menu and change the settings of your TV. Here’s
an overview of the menu system.
evel 1 evel 2 evel 3/Function
“A/V CONTROL”
“PICTURE MODE” Select the picture mode.
“DYNAMIC” n “STANDARD” n “SO T” n
“PERSONAL” n “ADJUST”
“ADJUST” Adjust the “PERSONAL” option
“PICTURE” n “COLOR” n “BRIGHT” n
“HUE” n “SHARP”
“SOUND MODE” Select the sound mode.
“DYNAMIC” n “DRAMA” n “SO T” n
“PERSONAL“ n “ADJUST”
“ADJUST” Adjust the “PERSONAL” option.
“BASS” n “TREBLE” n “BALANCE” n “BBE”
*
“SURROUND” Select the surround mode.
“HIGH” n “LOW” n “O ”
“PIP” “PIP POSITION” Change the position of the PIP screen.
“PIP” Display a sub screen within the main picture. “SWAP” Exchange program between main screen and sub
screen.
“SET UP” “LANGUAGE” Change the menu language.
“ENGLISH” – “ ”(Chinese)/ “ ”(Arabic)/
“” (Thai)
“CHILD LOCK” Block the channel independently.
“PIC ROTATION” Adjust the picture position.
“ AVORITE CH” Program favorite channels.
“INTELLIGENT VOL” Adjust volume automatically.
Return icon
“A/V CONTRO ” icon
“PIP” icon
“CH PRESET” icon
Name of the current menu
Menu level 3
Menu level 2
Adjusting Your Setup (MENU)
Menu level 1
“SET UP” icon
Menu guide icon
22
Adjusting Your Setup (MENU)
*
The BBE is manufactured by Sony Corporation under license from BBE
Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866.
The word “BBE” and the BBE symbol are the trademarks of BBE Sound, Inc.
The MENU button lets you open a menu and change the settings of your TV. Here’s
an overview of the menu system.
evel 1 evel 2 evel 3/Function
“A/V CONTROL”
“PICTURE MODE” Select the picture mode.
“DYNAMIC” n “STANDARD” n “SO T” n
“PERSONAL” n “ADJUST”
“ADJUST” Adjust the “PERSONAL” option
“PICTURE” n “COLOR” n “BRIGHT” n
“HUE” n “SHARP”
“SOUND MODE” Select the sound mode.
“DYNAMIC” n “DRAMA” n “SO T” n
“PERSONAL“ n “ADJUST”
“ADJUST” Adjust the “PERSONAL” option.
“BASS” n “TREBLE” n “BALANCE” n “BBE”
*
“SURROUND” Select the surround mode.
“HIGH” n “LOW” n “O ”
“PIP” “PIP POSITION” Change the position of the PIP screen.
“PIP” Display a sub screen within the main picture.
“SWAP” Exchange program between main screen and sub
screen.
“SET UP” “LANGUAGE” Change the menu language. “ENGLISH” –
“”(Chinese)/ “ ”(Arabic)/ “ ” (Thai)
“CHILD LOCK” Block the channel independently.
“PIC ROTATION” Adjust the picture position.
“ AVORITE CH” Program favorite channels.
“INTELLIGENT VOL” Adjust volume automatically.
“CH PRESET” “AUTO PROGRAM” Preset channels automatically.
“MANUAL PROGRAM”
Preset channels manually.
“SKIP” Skip unwanted or unused program positions.
“TV SYS” Select the TV system.
“B/G” n “I” n “D/K” n “M”
“COL SYS” Select the color system.
“AUTO” n “PAL” n “SECAM” n “NTSC3.58”
n “NTSC4.43”
Return icon
“A/V CONTRO ” icon
“PIP” icon
“CH PRESET” icon
Name of the current menu
Menu level 3
Menu level 2
Adjusting Your Setup (MENU)
Menu level 1
“SET UP” icon
Menu guide icon
Introducing the enu syste (KV-XS29M87 only)

http://cxema.ru
– 20 –
KV-XS29M31/33/50/60/63/65/93
RM-954
KV-XS29M39/69/87/89
RM-953
23
Adjusting Your Setup (MENU)
How to use the enu
You can use the buttons on the remote
and on the TV as well to display the
menu and adjust the settings.
1
Press MENU to display the
menu.
2
Press V or v to select the
desired item.
3
Press ENTER to con irm
your option and go to the
next menu level.
Other menu operations
To Press
Adjust the setting value V,b,v or B
Move to the next/previous menu level b or B
Cancel the menu MENU
Tips
• If you want to exit from Menu Level 2 to Menu Level 1, press V or v until
the return icon ( ) is highlighted, then press ENTER.
• You can also use the buttons on the TV for menu operations. ¸ +/–
works as V or v on the remote and … works as ENTER on the remote.
Note
• If more than 60 seconds elapse between entries, the menu screen
automatically disappears.
PROGR
AUTO
PROGR
MENU
+
V/b/v/B/ENTER
MENU
Front of TV
+
ENTER
ENTER
0
/
FAVORITE
PIP PROGR
PIP PROGR
ENTER
Adjusting Your Setup (MENU)
24
Adjusting Your Setup (MENU)
FAVORITE
PIP PROGR
PIP PROGR
ENTER
MENU
Changing the “A/V
CONTROL” setting
The “A/V CONTROL” menu allows
you to change the picture and sound
settings.
1
Press MENU.
2
Make sure the “A/V
CONTROL” icon ( ) is
selected, then press
ENTER.
3
Press V or v to select
either
“PICTURE MODE”,
“SOUND MODE”, or
“SURROUND”, then press
ENTER.
4
Press V or v to select the
desired option, then
press ENTER.
For Select
“PICTURE MODE” either “DYNAMIC”, “STANDARD”, “SO T”, “PERSONAL”*, or
“ADJUST”.
“SOUND MODE” either “DYNAMIC”, “DRAMA”, “SO T”, “PERSONAL”*, or
“ADJUST”.
“SURROUND” either “HIGH”, “LOW”, or “O ”.
* When the “PERSONAL” mode is selected, the last adjusted picture
and sound settings from the “ADJUST” option are received.
Tip
• or details on the options under “PICTURE MODE” and “SOUND
MODE”, or “SURROUND”, see page 13 or 17 respectively.
To return to the normal screen
Press MENU.
ENTER
ENTER ENTER
V/b/v/B/ENTER
ENTER ENTER