Sony Trinitron KV-EX29M93 User manual

http://cxema.ru
MODEL COMMANDER DEST. CHASSIS NO.
KV-EX29M93 RM-964 Hong Kong SCC-U40A-A
KV-EX29M39 RM-963 OCE SCC-U41B-A
KV-EX29M6 RM-964 Malaysia SCC-U42B-A
KV-EX29M87 RM-963 ME SCC-U43A-A
KV-EX34M97 RM-963 Hong Kong SCC-U40B-A
MODEL COMMANDER DEST. CHASSIS NO.
CHASSIS
TRINITRON ® COLOR TV
SERVICE MANUAL AG-3E
231
564
897
0
JUMP
DRC-MF
PROGR
MENU
FAVORIT E RESET
SOUND
MODE
SURROUND
PIC MODE
VIDEO
TITLE
TV
PIP PROGR
PIP PROGR
ENTER
RM-963RM-964
1
4
7
2
5
8
0
3
6
9
FAVORITE
SOUND
MODE
RESET
PIC MODE
PROGR
DRC-MF
ENTER
MENU
SURROUND
JUMP

http://cxema.ru
– 2 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
SPECIFICATIONS
( V-EX29M65/EX29M93)
Note
Power requirements 220-240 V AC, 50/60 Hz
Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K,
Color system PAL, PAL 60, SECA , NTSC4.43, NTSC3.58
Stereo/Bilingual system NICA Stereo/Bilingual B/G, I, D/K; A2 Stereo/Bilingual B/G
Teletext Language English, Arabic, French KV-EX29 65 only
Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41
IUHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/ VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
MVHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘ (Antenna) 75-ohm external terminal
Audio output (Speaker) 6W + 6W
3D WOOFER 15W
Number of terminal
D (Video) Input: 4 Output: 1 Phono jacks; 1 VP-P, 75 ohms
≥ (Audio) Input: 4 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync
negative
C : 0.286 Vp-p, 75 ohms
(Component Video) Input: 1 Phono jacks
Y : 1 Vp-p, 75 ohms,
sync negative
CB : 0.7 Vp-p, 75 ohms
CR : 0.7 Vp-p, 75 ohms
Audio : 500 mVrms
2 (Headphones) Output: 1 Stereo minijack
Picture tube 29 inch
Tube size (cm) 72 easured diagonally
Screen size (cm) 68 easured diagonally
Dimension (w/h/d, mm) 722 x 603 x 516
Mass (kg) 56
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MAR ! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.

http://cxema.ru
– 3 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
SPECIFICATIONS
( V-EX29M39/EX29M87/EX34M97)
Note
Power requirements 110-240 V AC, 50/60 Hz E only
220-240 V AC,50/60 Hz OCE/Hong Kong only
Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K,
Color system PAL, PAL 60, SECA , NTSC4.43, NTSC3.58
Stereo/Bilingual system NICA Stereo/Bilingual B/G, I, D/K; A2 Stereo/Bilingual B/G KV-EX29 39, EX29 97 only
Teletext Language English, Arabic, French KV-EX29 39 only
Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41
VHF: 0 to E12,5A,9A / UHF: 28 to 69 / CATV: S01 to S03, S1 to S41
VHF: 1 to 11 / UHF: 21 to 69 / CATV: S01 to S03, S1 to S41
IUHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/ VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: S01 to S03, S1 to S41, Z1 to Z39
MVHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘ (Antenna) 75-ohm external terminal
Audio output (Speaker) 6W + 6W
3D WOOFER 15W
Number of terminal
D (Video) Input: 4 Output: 1 Phono jacks; 1 VP-P, 75 ohms
≥ (Audio) Input: 4 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync
negative
C : 0.286 Vp-p, 75 ohms
(Component Video) Input: 1 Phono jacks
Y : 1 Vp-p, 75 ohms,
sync negative
CB : 0.7 Vp-p, 75 ohms
CR : 0.7 Vp-p, 75 ohms
Audio : 500 mVrms
2 (Headphones) Output: 1 Stereo minijack
Picture tube 29 inch 34 inch
Tube size (cm) 72 86 easured diagonally
Screen size (cm) 68 80 easured diagonally
Dimension (w/h/d, mm) 722 x 603 x 516 895 x 700 x 590
Mass (kg) 56 84
Design and specifications are subject to change without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MAR ! ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
CAUTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR
CARBON PAINTED ON THE CRT, AFTER REMOVING THE
ANODE.

http://cxema.ru
– 4 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
TABLE OF CONTENTS
Section Title Page
SELF DIAGNOSIS FUNCTION ................................ 5
1. GENERAL ........................................................................ 8
2. DISASSEMBLY
2-1. Speaker Box Removal ............................................. 53
2-2. Rear Cover Removal ................................................ 53
2-3. Speaker Removal ..................................................... 53
2-4. Chassis Assy Removal ............................................. 53
2-5. Service Position ....................................................... 53
2-6. Replacement of Parts ............................................... 54
2-7. PWB Holder Removal ............................................. 54
2-8. Terminal Bracket Removal ...................................... 54
2-9. B3, P, V2 and D1 Boards Removal ........................ 54
2-10. H1 Board Removal .................................................. 54
2-11. A and D Boards Removal ........................................ 54
2-12. Picture Tube Removal .............................................. 55
2-13. Removal of Anode Cap ............................................ 55
3. SERVICE JIG
3-1. Jig Required for Servicing ....................................... 56
4. CIRCUIT BOARDS LOCATION ............................... 56
5. ADVANCE OPERATION
5-1. "RESET" Function ................................................... 57
6. SET-UP ADJUSTMENTS
6-1. Beam Landing .......................................................... 58
6-2. Convergence Adjustment ......................................... 59
6-3. Focus Adjustment .................................................... 61
6-4. Neck Assy Twist Adjustment ................................... 61
6-5. G2 (Screen) and White Balance Adjustments ......... 62
7. CIRCUIT ADJUSTMENTS
7-1. Adjustments with Commander ................................ 63
7-2. Adjustment ethod ................................................. 63
7-3. Picture Quality Adjustments .................................... 74
7-4. Deflection Adjustment ............................................. 75
7-5. A Board Adjustment After IC003
(memory) Replacement ........................................... 75
7-6. Picture Distortion Adjustment ................................. 76
Section Title Page
8. DIAGRAMS
8-1. Block Diagram .......................................................... 77
8-2. Schematic Diagrams ................................................. 84
(1) Schematic Diagrams of F1, J and V Boards ... 85
(2) Schematic Diagram of A Board .......................... 87
(3) Schematic Diagram of D Board ....................... 103
(4) Schematic Diagram of D1 Board .................... 111
(5) Schematic Diagram of B3 Board ..................... 119
(6) Schematic Diagram of P Board ........................ 127
(7) Schematic Diagram of C Board ........................ 129
(8) Schematic Diagram of V2 Board ...................... 131
(9) Schematic Diagram of H1 Board ..................... 133
(10) Schematic Diagram of DH Board ................... 135
8-3. Voltage easurements ............................................ 138
8-4. Waveforms .............................................................. 151
8-5. Printed Wiring Boards and Parts Location ............. 153
8-6. Semiconductors ....................................................... 165
9. EXPLODED VIEWS
9-1. Speaker Bracket ...................................................... 167
9-2. 3D Speaker .............................................................. 167
9-3. Chassis .................................................................... 168
9-4. Picture Tube ............................................................ 169
10. ELECTRICAL PARTS LIST.................................... 170

http://cxema.ru
– –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS
When an error occurs, the STANDBY/TIMER lamp will flash a number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic
Item
Description
• Power does not
turn on
• +B overcurrent
(OCP)
• +B overvoltage
(OVP)
• Vertical deflection
failure
• White balance
failure (no
PICTURE)
• Horizontal
deflection failure
• Micro reset
No. of times
STANDBY/TIMER
lamp flashes
Does not light
2 times
3 times
4 times
times
6 times
—
Self-diagnostic
display/Diagnostic
result
—
002:000 or
002:001~2
003:000 or
003:001~2
004:000 or
004:001~2
00 :000 or
00 :001~2
006:000 or
006:001~22
101:00 or
101:001~22
Probable
Cause
Location
• Power cord is not plugged
in.
• Fuse is burned out F1601
(F1 Board)
• H.OUT Q6807 is shorted.
• H.IN Q6810 is shorted.
(D board)
• PH 6602 faulty.
• 10. V is not supplied.
(D board)
• V.OUT IC6800 faulty
D6816 faulty
D6817 faulty
D6824 faulty
R68 2 open
R68 1 open (D board)
• G2 is improperly adjusted.
(Note 2)
• CRT problem.
• Video OUT IC9001, 9002,
9003 are faulty. (C board)
• IC8306 (A board) and
IC4301 (A board) are faulty.
• C6831 is open circuit.
(D board)
• CRT Discharge (C Board)
• Static discharge
• External noise
Detected
Symptoms
• Power does not come on.
• No power is supplied to the
TV.
• AC power supply is faulty.
• Power does not come on.
• Load on power line is
shorted.
• Power does not come on.
• Vertical deflection pulse is
stopped.
• Vertical size is too small.
• Vertical deflection stopped.
• No raster is generated.
• CRT cathode current
detection reference pulse
output is small.
• H pulse output is too high.
• Power is shut down shortly,
after this return back to
normal.
• Detect Micro latch up.
Note 1: Refer to screen (G2) Adjustment in section 6- of this manual.
SELF DIAGNOSTIC FUNCTION

http://cxema.ru
– 6 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
3. STOPPING THE STANDBY/TIMER FLASH
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.
4. SELF-DIAGNOSTIC SCREEN DISPLAY
For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]
In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screendisplay] /channel [5] /Sound volume [-] /Power ON
˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
STANDBY/SLEEP lamp
Lamp ON 0.3 sec.
Lamp OFF 3 sec.
Lamp OFF 0.3 sec.
2 times
3 times
4 times
times
6 times
Diagnostic Item Flash Count*
+B overcurrent 2 times
+B overvoltage 3 times
V deflection stop 4 times
White balance failure times
Horizontal Deflection Failure 6 times
* One flash count is not used for self-diagnostic.
002 : 000
003 : 000
004 : 000
00 : 001
Numeral "0" means that no fault has been detected.
Numeral "1" means a fault has been detected.
006 : 002
101 : 000
SELF DIAGNOSTIC
Numeral "2" means two faults have been detected.

http://cxema.ru
– 7 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]
To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel [8] /0
[Quitting Self-diagnostic screen]
To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
6. SELF-DIAGNOSTIC CIRCUIT
[+BovercurrentªOCPº] Occurs when an overcurrent on the +B(13 ) line is detected by Q6610
and Q6609.
If Q6610 and Q6609 go to ON, the voltage to the pin3 of IC001 go to UP.
The unit will automatically turn off.
[+BovervoltageªOVPº] Occurs when an overvoltage on the +B(13 ) line is detected by D663 ,
Q6611 and Q6612. If Q6611 and Q6612 go to ON, the voltage to pin6 of
IC001 go to UP. The unit will automatically turn off.
[Verticalde lection ailure] Occurs when an absence of the vertical deflection pulse is detected by
Q6811, Q6819, Q6820, Q6821 and D6801. Shut down the power supply.
[Whitebalance ailure] If the RGB levels do not balance or become low level within seconds.
This error will be detected by IC4301.
TV will stay on, but there will be no picture.
[Highvoltageprotectoro HorizontalDe lection] Occurs when an overvoltage of horizontal pulse is detected by D6809 and
IC6801.
If the voltage of 7 pin of IC6801 goes to High, the voltage to pin20 of
IC4301 go to UP. The unit will automatically turn off.
IC4301
RGB JUNGLE
CXA2100Q
OVP OCP
FROM
CRT (IK)
[V] D6806/D6801
IC001
SYSTEM
SDA
SDA
IC003
MEMORY
IKIN
XRAY
LED 1
2
20
4
3
6
V PROT 1
16
[H] IC6801

http://cxema.ru
– 8 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
SECTION 1
GENERAL 1-1
( V-EX29M39/EX29M87/EX34M97)
2
WARNING
• Dangerously high voltages are present inside the TV.
• TV operating voltage: 110 – 240 V AC. ( or Hong Kong and OCE only: 220-240 V AC.)
To prevent fire or shock hazard, do not expose
the TV to rain or moisture.
Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by
qualified personnel only.
Do not open the cabinet and the rear cover of the
TV as high voltages and other hazards are
present inside the TV. Refer servicing and
disposal of the TV to qualified personnel.
Your TV is recommended for home use only.
Do not use the TV in any vehicle or where it may
be subject to excessive dust, heat, moisture or
vibrations.
Do not block the ventilation openings of the TV.
Do not install the TV in a confined space, such
as a bookcase or built-in cabinet.
or children’s safety, do not leave children
alone with the TV. Do not allow children to
climb onto it.
Do not plug in too many appliances to the same
power socket. Do not damage the power cord.
Clean the TV with a dry and soft cloth.
Do not use benzine, thinner, or any other chemicals
to clean the TV. Do not scratch the picture tube.
or your own safety, do not touch any part of the
TV, the power cord and the antenna cable during
lightning storms.
Pull the power cord out by the plug. Do not pull
the power cord itself. Disconnect the TV before
moving it or if you are not going to use it for
several days.
3
Do not install the TV in an unstable position.
Use a proper TV stand. Do not place any objects on the TV.
WARNING (continued)
The operating instruction mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.

http://cxema.ru
– 9 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
4Using Your New TV
Using Your New TV
: Signal flow
IEC connector
(not supplied)
or
Antenna cable (not supplied)
Antenna cable (not supplied)
Rear of TV
To video and
audio outputs
To S video
output
Audio/Video cable
(not supplied)
: Signal flow
To
(S video input)
VCR
Antenna cable (not supplied)
To antenna
output
To ˘ (antenna)
123
RLYC
B
C
R
WOOFER
4
VIDEO
VIDEO IN
VIDEO OUT
AUDIO
R L
Rear of TV
( ellow)
-L (MONO) (white)
-R (red)
To T 1, 2, or 3
(video input)
Getting Started
Step 1
Connect the antenna
If you wish to connect a VCR, see the Connecting a VCR diagram below.
Connecting a VCR
To watch the video input, press t (see page 12).
CAUTION
• Do not connect the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through
the antenna and other terminals to ground.
• To avoid battery leakage and damage to the remote, remove the batteries
from the remote if you are not going to use it for several days. If any
liquid that leaks from the batteries touches you, immediately wash it
away with water.
S video cable
(not supplied)
5
Using Your New TV
Using Your New TV
2
L(MONO) R
4
PROGR
MENU AUTO
PROGR
ENTER SELECT
AUTO
PROGR
1
b
M
PR : 0 1
AUTO PROGRA
VHF LOW
TV SYS:AUTO
1
b
Front panel
Notes
• If you connect a monaural VCR, connect the yellow plug to (the yellow
jack) and the black plug to -L (MONO) (the white jack).
• If you connect a VCR to the 8 (antenna) terminal, preset the signal
output from the VCR to the program number 0 on the TV.
• When both the (S video input) and t 1 (video input) are connected,
the (S video input) is automatically selected. To view the video input
to t 1 (video input), disconnect the S video cable.
Step 2
Insert the batteries into
the re ote
Note
• Do not use old batteries or different types of batteries together.
Step 3
Preset the channels auto atically
Tips
• To stop the automatic channel presetting, press MENU.
• If your TV has preset an unwanted channel or cannot preset a particular
channel, then preset your TV manually (see page 38).

http://cxema.ru
– 10 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
6Using Your New TV
Connecting the 3D WOOFER
You can enjoy high quality sound by connecting the 3D WOO ER.
Bottom of 3D WOOFER
1
Place the foot at the front of the 3D WOOF R into the footholds on the top
of your TV.
2
Place the foot at the rear of the 3D WOOF R into the footholds at the rear
of your TV.
3
Connect the wires to the 3D WOOF R (4Ω) terminals at the rear of your TV.
The red wire should be connected to the ‘ red terminal and the black wire
to the ’ black terminal.
Notes
• Connect only the supplied 3D WOO ER; otherwise your TV may
malfunction.
• Unplug your TV from the wall outlet when connecting the 3D WOO ER.
• To prevent a malfunction caused by a short circuit of the terminals, make
sure that none of the 3D WOO ER wire strands stick out, making contact
with it’s neighbouring 3D WOO ER terminal.
Rear of TV
3D WOOFER
1
2
3
Black wire
Red wire
7
Using Your New TV
Using Your New TV
Connecting optional co ponents
You can connect optional audio/video components, such as a VCR, multi disc player,
camcorder, video game, or stereo system. To watch and operate the connected
equipment, see pages 12 and 25.
Connecting a ca corder/video ga e equip ent
using the t (video input) jacks
Notes
• When connecting video game equipment, display the “PICTURE” menu
and select “ON” for “GAME MODE” to adjust the picture setting that is
suitable for video games (see page 30).
• You can also connect video equipment to the t 1, 2, or 3 (video input)
jacks at the rear of your TV.
• When both the (S video input) and t 4 (video input) are connected,
the (S video input) is automatically selected. To view the video input
to t 4 (video input), disconnect the S video cable.
Connecting audio/video equip ent using the T
( onitor output) jacks
Note
• If you select “DVD” on your TV screen, no signal will be output at the
T (monitor output) jacks (see page 12).
: Signal flow
or
Video game
equipment
( ellow)
-L (MONO)
(white)
-R (red)
Rear of TV
To
antenna
output
To video and
audio inputs
Audio s stem
To
audio
inputs
VCR
: Signal flow
To T
(monitor
output)
Antenna cable (not supplied)
Audio cable
(not supplied)
Audio/Video cable (not supplied)
L(MONO) R
4
PROGRMENU AUTO
PROGR
ENTER SELECT
L(MONO) R
4
123
RLYC
B
C
R
WOOFER
4
continued
Camcorder
To video and
audio outputs
To
(S video
input)
To
…
4
(video input)
or
Audio/Video cable (not supplied)
S video cable (not supplied)
Front of TV
To S video output

http://cxema.ru
– 11 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
8Using Your New TV
Connect To (on the DVD pla er)
Y (green) Y
C
B
(blue) C
b
, B-Y or P
B
C
R
(red) C
r
, R-Y or P
R
Connecting a DVD player to (co ponent video input)
1 Using an audio cable, connect R and L under (component video input) on your
TV to the LINE OUT, AUDIO R and L output connectors on your DVD player.
2 Using a component video cable, connect Y, C
B
, and C
R
under (component video
input) on your TV to the COMPONENT VIDEO OUT Y, C
B
, and C
R
output
connectors on your DVD player.
3 Press t on the remote or the TV until “DVD” appears on the screen.
To component
video output
Component video cable
(not supplied)
DVD pla er
To
L (white)
R (red)
To audio
output
Audio cable
(not supplied)
: Signal flow
To
(component video input)
VIDEO
R-AUDIO-L
LINE OUT
Y
COMPONENT VIDEO OUT
S VIDEO OUT
C
B
C
R
RLYC
B
C
R
Notes
• Some DVD player terminals may be labeled differently:
• When connecting to (component video input) on your TV, you must
connect Y, C
B
, and C
R
to receive the video signals, and connect L and R to
receive analog audio signals.
Connecting optional components (continued)
Rear of TV
9
Using Your New TV
Using Your New TV
123
RLYC
B
C
R
WOOFER
4
VIDEO
R-AUDIO-L
LINE OUT
Connecting a DVD player to t (video input)
Connect t 1, 2, or 3 (video input) / (audio/video) connectors on your TV to LINE
OUT on your DVD player.
DVD pla er
( ellow)
-L (MONO) (white)
-R (red)
To t 1, 2, or 3
(video input)
: Signal flow
Audio/Video cable (not supplied)
Notes
• Since the high quality pictures on a DVD disc contain a lot of information,
picture noise may appear. In this case, adjust the sharpness (“SHARP”)
under “PERSONAL ADJUST” in the “PICTURE MODE” menu (see
page 31).
• Connect your DVD player directly to your TV. Connecting the DVD
player through other video equipment will cause unwanted picture noise.
Rear of TV

http://cxema.ru
– 12 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
10 Using Your New TV
AB
Securing the TV
To prevent the TV from falling, secure the TV using one of the following methods:
A
With the supplied screws, attach the stabilizer band to the TV stand and to
the rear of the TV using the provided hole.
OR
B
Put the cord or chain through the clamps to secure the TV against a wall or
pillar.
Note
• Use only the supplied screws. Use of other screws may damage the TV.
OR
3.8 mm
20
mm
11
Using Your New TV
Using Your New TV
Number buttons
PROGR +/–
Watching the TV
This section explains various functions
and operations available while watching
the TV. Most operations can be done
using the remote.
or
231
564
897
0
JUMP
DRC-MF
PROGR
MENU
FAVOR I TE RESET
SOUND
MODE
SURROUND
PIC MODE
PIP PROGR
PIP PROGR
ENTER
PROGRMENU AUTO
PROGR
ENTER SELECT
L(MONO) R
4
PROGRMENU AUTO
PROGR
ENTER SELECT
123
456
78
0
9
JUMP
PROGR
1
Press ! to turn on the TV.
When the TV is in standby
mode (the 1 indicator on
the TV is lit red), press ?/1
on the remote or
PROGR +/– on the TV.
2
Press PROGR +/– or the
number buttons to select
the TV channel.
or double digit numbers, press
-, then the number (e.g., for 25,
press -, then 2 and 5).
Note
• When you turn on the TV, either the program number or video mode is
displayed for approximately 40 seconds. The ECO MODE ( ) icon will
also appear if “ECO MODE “ in the “SETUP” menu is set “ON” (see
page 35).
To select a TV program quickl
(1) Press and hold PROGR +/–.
(2) Release PROGR +/– when the desired program number appears.
Note
• When you select a TV program quickly, the picture may be disrupted.
This does not indicate a malfunction.
1 indicator
continued

http://cxema.ru
– 13 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
12 Using Your New TV
Watching the TV (continued)
To
Turn off temporarily
Turn off completely
Adjust the volume
Mute the sound
Watch the video input
(VCR, camcorder, etc.)
Jump back to the previous channel
Display the on-screen information*
Press
1/1.
The 1 indicator on the TV lights up red.
! on the TV.
2+/–.
%.
t (or t on the TV) to select “VIDEO 1”,
“VIDEO 2”, “VIDEO 3”, “VIDEO 4”or “DVD”.
To return to the TV screen, press a (or t on the TV).
JUMP.
.
Additional tasks
JUMP
. +/–
MENU
231
564
897
0
JUMP
DRC-MF
PROGR
MENU
FAVORITE RESET
SOUND
MODE
SURROUND
PIC MODE
VIDEO
TITLE
TV
PIP PROGR
PIP PROGR
ENTER
V/v/ENTER
* Some picture/sound settings, and either the program number or video
mode are displayed. The on-screen display for the picture/sound settings
disappears after about 3 seconds.
PROGRMENU AUTO
PROGR
ENTER SELECT
L(MONO) R
4
PROGRMENU AUTO
PROGR
ENTER SELECT
1 indicator
13
Using Your New TV
Using Your New TV
Changing the enu language
You can change the menu language as well as the on-screen language. or details on
how to use the menu, see Introducing the menu system on page 27.
1
Press M NU.
2
Press V or v to select ,
then press NT R.
3
Make sure “LANGUAG ” is
selected then press NT R .
4
Press V or v to select the
desired language
(e.g.,” “), then
press NT R .
The selected menu
language appears.
To return to the normal screen
Press MENU.
PICTURE MO C
PICTURE
GAME MODE ++++++++++++
WI DE MODE : OF F
:OFF
DE : DYNAM I
DRC - MF : DRC1 2 0
E
COLOR SYS : AUTO
SETUP
PROGRAM SETUP
PIC ROT A T I ON
NGL I SH
ECO MODE : OFF
LANGUAGE :
MENU
b
ENTER
b
L ANGUAGE :
COLOR SYS :
T
SETUP
PROGRAM SE
F
PIC ROT A T I O
ENGL I SH
ECO MODE : O
A
continued
ENTER ENTER
bb
ENTER ENTER
bb

http://cxema.ru
– 14 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
14 Using Your New TV
Setting the Wake Up ti er
1
Press until the desired
period of time appears.
The Wake Up timer starts
immediately after you
have set it.
2
Select the TV channel or video mode you want to wake up to.
3
Press 1/1, or set the Sleep timer if you want the TV to turn off
automatically.
The indicator on the TV lights up orange.
To cancel the Wake Up timer
Press until “WAKE UP TIMER: O ” appears, or turn off the
TV’s main power.
Note
• If no buttons or controls are pressed for more than two hours after the TV
is turned on using the Wake Up timer, the TV automatically goes into
standby mode. To resume watching the TV, press any button or control on
the TV or the remote.
Setting the Sleep ti er
Press until the desired
period of time appears.
The Sleep timer starts
immediately after you
have set it.
To cancel the Sleep timer
Press until “SLEEP TIMER: O ” appears, or turn the TV off.
WA E UP TIMER:10M
WA E UP TIMER:OFF WA E UP TIMER:12H00M
After 10 minutes
No Wake Up Timer After 12 hours
SLEEP TIMER:30M SLEEP TIMER:60M
SLEEP TIMER:OFF SLEEP TIMER:90M
After 30 minutes
No Sleep Timer
After 60 minutes
After 90 minutes
Watching the TV (continued)
15
Advanced Operations
Advanced Operations
Advanced Operations
Selecting the picture ode
Press PIC MOD
repeatedly until the
desired picture mode is
selected.
Select
“DYNAMIC”
“STANDARD”
“HI- INE”
“PERSONAL”
To
receive high contrast pictures.
receive normal pictures.
receive higher resolution pictures with mild contrast.
receive the last adjusted picture setting from the “ADJUST” option in the
“PICTURE” menu (see page 31).
Selecting the sound ode
Press SOUND MOD
repeatedly until the
desired sound mode is
selected.
Select
“DYNAMIC”
“DRAMA”
“SO T”
“PERSONAL”
To
listen to dynamic and clear sound that emphasizes both the low and high
tones.
listen to sound that emphasizes voice and high tones.
receive soft sound.
receive the last adjusted sound setting from the “ADJUST” option in the
“SOUND” menu (see page 33).
Tip
• You can also set the picture and sound modes using the menu (see
Changing the “PICTURE” setting on page 30 and Changing the
“SOUND” setting on page 32 ).
Selecting the picture
and sound odes
You can select picture and sound modes
and adjust the setting to your preference
in the “PERSONAL” option.
PROGR
MENU
FAVORITE RESET
SOUND
MODE
SURROUND
PIC MODE
PIP PROGR
PIP PROGR
ENTER
PIC MODE
PERSONAL
DYNAMIC
HI-FINE
STANDARD
PIC MODE
≥
DYNAMIC
≥
PERSONAL
≥
SOFT
≥
DRAMA
SOUND
MODE
SOUND MODE

http://cxema.ru
– 1 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
16 Advanced Operations
Viewing higher
quality pictures
— “DRC-MF”
The Digital Reality Creation-Multi
unction (DRC-M ) feature allows you
to enjoy higher quality pictures on your
TV. You can select “DRC1250” to watch
super real (higher resolution) pictures,
or “DRC PROGRESSIVE” to reduce any
jittering on the screen if necessary.
Press DRC-MF repeatedly
until you receive the
desired picture quality.
Tips
• You can also select the DRC-M option using the menu (see Changing the
“PICTURE” setting on page 30).
• When the broadcast signal is weak, you may see some dots or noise on the
TV screen. To reduce this interference, display the “PICTURE” menu and
select “ADJUST” in “PICTURE MODE”, then adjust “SHARP” to reduce
the sharpness (see page 31).
Note
• The DRC-M mode is not selectable when the “GAME MODE” or Picture-
In-Picture (“PIP”) mode is turned “ON”.
The DRC-M logo ( ) and “DRC-M ” are trademarks of
Sony Corporation.
Select
“DRC1250”
“DRC PROGRESSIVE”
To
select higher resolution pictures.
reduce jitter of any small areas or scanning lines (e.g., letters
or the edge of objects) on the screen.
231
564
897
0
JUMP
DRC-MF
MENU
FAVORI T E RESET
SOUND
MODE
SURROUND
PIC MODE
PIP PROGR
PIP PROGR
ENTER
DRC-MF
DRC-MF: DRC1250 DRC-MF: DRC PROGRESSIVE
DRC-MF
17
Advanced Operations
Advanced Operations
FAVORITE
231 564
897
0
JUMP
DRC-MF
PROGR
MENU
FAVORI T E RESET
SOUND
MODE
SURROUND
PIC MODE
VIDEO
TITLE
TV
PIP PROGR
PIP PROGR
ENTER
1
Press FAVORIT .
2
Press the number button
from 1 to 6 to select the
desired channel.
Tip
• To program your favorite channels, see Ad usting each channel settings
(PROGRAM SETUP) on page 36.
Viewing your
favorite channels
You can display and select six of your
favorite channels directly from your TV
screen.
Number buttons
b
FAVORITE
123
456
1

http://cxema.ru
– 16 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
18 Advanced Operations
Watching two
progra s at the
sa e ti e
— “PIP”
With the Picture-in-Picture (PIP) feature,
you can display a sub screen within the
main picture of different TV programs
or video inputs.
Displaying a sub screen
Press .
To return to the normal screen
Press (when displaying the sub screen).
12
///
231
564
897
0
JUMP
DRC-MF
PROGR
MENU
FAVORITE RESET
SOUND
MODE
SURROUND
PIC MODE
VIDEO
TITLE
TV
PIP PROGR
PIP PROGR
ENTER
V (PIP PROGR +)/
v (PIP PROGR –)
19
Advanced Operations
Advanced Operations
Additional PIP tasks
To
change a TV program in the sub
screen
select a video input in the sub screen
swap pictures between the main
and sub screens
freeze the sub screen
Tip
• You can also display the sub screen and exchange pictures between the
main and sub screens using the menu (see Changing the “PIP” setting on
page 34).
Notes
• When you display a video input on the sub screen at a faster/slower
speed, the picture may be disrupted depending on the VCR type.
• If you display different color systems on the main screen and the sub
screen, the size of the sub screen may be different and the sub screen
picture may be disrupted. This does not indicate a malfunction of the TV.
Press
V (PIP PROGR +) or v (PIP PROGR –).
.
.
.
To unfreeze the screen, press the button again.

http://cxema.ru
– 17 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
20 Advanced Operations
Press SURROUND
repeatedly until you
receive the desired
surround sound.
Select To
“TruSurround” listen to the surround sound that spreads out to the rear of a room.
“O ” turn off the surround sound.
Tip
• You can also select the surround option using the menu (see Changing the
“SOUND” setting on page 32).
The surround of your TV is categorized as TruSurround.
TM
is a trademark of SRS Labs, Inc. SRS and the SRS symbol are
registered trademarks of SRS Labs, Inc. in the United States and selected foreign
countries. SRS and TruSurround are incorporated under license from SRS Labs,
Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572
with numerous additional issued and pending foreign patents.
Listening with
surround sound
The surround feature enables you to
enjoy the sound effects of a concert hall
or movie theater.
PROGR
MENU
FAVORITE RESET
SOUND
MODE
SURROUND
PIC MODE
VIDEO
TITLE
TV
PIP PROGR
PIP PROGR
ENTER
SURROUND: OFF
SURROUND: TruSurround
SURROUND
21
Advanced Operations
Enjoying stereo or
bilingual
progra s
You can enjoy stereo sound or bilingual
programs of NICAM and A2 stereo
systems.
Press A/B repeatedly until
you receive the sound you
want.
The on-screen display
changes to show the
selected sound.
The  indicator on the TV
lights up red when
receiving any stereo or
bilingual program.
When receiving a NICAM program
A/B
Broadcasting On-screen displa (Selected sound)
NICAM stereo
NICAM bilingual
NICAM monaural
231
564
897
0
JUMP
DRC-MF
NICAM MONO
(Stereo sound) (Regular sound)
NICAM
MAIN
MONO
(Main sound) (Regular sound)
NICAM
SUB
(Sub sound)
NICAM
MAIN
MONO
(Main sound)
(Regular sound)
NICAM
A/B
continued
(KV-EX29M39, EX34M97 only)

http://cxema.ru
– 18 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
22 Advanced Operations
When receiving an A2 program
Receiving area for NICAM and A2 programs
Notes
• If the signal is very weak, the sound becomes monaural automatically.
• If the stereo sound is noisy when receiving a NICAM program, select
“MONO”. The sound becomes monaural, but the noise is reduced.
• Before receiving a NICAM stereo program in China, please check the
NICAM broadcast condition in your area. When receiving a NICAM
stereo program, the receiving conditions might vary depending on area. In
addition, different strength of the NICAM broadcast signal might affect
the receiving quality.
If the sound is distorted when receiving a monaural program
through the 8 (antenna) terminal
Press A/B repeatedly until “MONO” appears on the screen.
To cancel the monaural sound setting, press A/B again until
“AUTO” appears on the screen.
Notes
• The “MONO” or “AUTO” setting is memorized for each program
position.
• You cannot receive a stereo broadcast signal when the TV is in the
“MONO” setting. Normally, set the TV to “AUTO”.
Broadcasting On-screen displa (Selected sound)
A2 stereo
A2 bilingual
STEREO
MONO
(Stereo sound)
(Regular sound)
MAIN SUB
(Main sound) (Sub sound)
MONO AUTO
S stem
NICAM
A2
Receiving area
Hong Kong, Singapore, New Zealand, Malaysia,
Thailand, etc.
Australia, Malaysia, Thailand, etc.
Enjoying stereo or ilingual programs (continued)
23
Advanced Operations
Viewing Teletext
(KV-EX29M39 onl )
Some TV stations broadcast an
information service called Teletext
which allows you to receive various
information, such as stock market
reports and news.
Displaying Teletext
1
Select a TV channel that carries the Teletext broadcast you want to watch.
2
Press to display the
text.
A Teletext page (normally
the index page) is
displayed. If there is no
Teletext broadcast, “100” is
displayed at the top left
corner of the screen.
To turn off Teletext
Press a.
A/B
231 564
897
0
JUMP
DRC-MF
PROGR
MENU
FAVORI T E RESET
SOUND
MODE
SURROUND
PIC MODE
VIDEO
TITLE
TV
PIP PROGR
PIP PROGR
ENTER
P166 SECTEXT 166 FR1 MAR 03: 9:09 From Singapore To PARIS To OSAKA To ROMA To SYDNEY
Day Dep/Arr Flight Alrcraft
1.6 220/0 88 SQ28 747
2 2130/122 PA11 L1 3 211 /1330 SQ26 747 2.7 2130/074 SQ24
747
4 2300/091 AZ487 747 2. 1000/171 SQ6 747 4.6 0930/201 CX 22 L10 1 2210/0610 SQ21A 747 2 2100/083 SQ21A 747
continued
(red, green,
ellow,blue)

http://cxema.ru
– 19 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
24 Advanced Operations
Additional Teletext tasks
To
display a Teletext page on the TV
picture
check the contents of a Teletext service
select a Teletext page
hold (pause) a Teletext display
reveal concealed information
(e.g., an answer to a quiz)
enlarge the Teletext display
stand by for a Teletext page while
watching a TV program
* You can also select a Teletext page that appears in the colored columns at
the bottom of the screen using the corresponding color-coded buttons on
the remote.
Using FASTEXT
This feature allows you to quickly access a Teletext page that uses
ASTEXT. When a ASTEXT program is broadcast, colored menus
appear at the bottom of the screen. The color of each menu
corresponds to the color-coded buttons on the remote (red ,
green , yellow , and blue ).
To access a FASTEXT menu
Press the color-coded button on the remote corresponding to the
menu you want. The menu page appears on the screen after a few
seconds.
Do this
Press .
Each time you press , the screen changes as
follows: Teletext n Teletext and TV n TV.
Press .
An overview of the Teletext contents, including
page numbers, appears on the screen.
Press the number buttons to enter the three-digit
page number of the desired Teletext page.* If you
make a mistake, reenter the correct page number. To
access the next or previous page, press PROGR +/–.
Press to display the symbol “j” at the top left
corner of the screen. To resume normal Teletext
viewing, press or .
Press .
To conceal the information, press the button again.
Press .
Each time you press , the Teletext display
changes as follows: Enlarge upper half n Enlarge
lower half n Normal size.
1 Enter the Teletext page number that you want to
refer to, then press .
2 When the page number is displayed, press to
show the text.
Viewing teletext (continued)
25
Advanced Operations
or example, to operate a
Sony 8 mm VCR:
VIDEO I/1
Video equipment
operation buttons
Number buttons
b
02
+
VIDEO
231
564
897
0
JUMP
PROGR
MENU
FAVORITE RESET
SOUND
MODE
SURROUND
PIC MODE
VIDEO
TITLE
PIP PROGR
PIP PROGR
ENTER
Code numbers for Son video equipment
MENU
continued
Operating
optional
co ponents
You can use the supplied remote to
operate Sony video equipment such as
Beta, 8 mm, VHS, MDP, CD or DVD.
Setting up the re ote to work with other
connected equip ent
While holding down VID O
?/1
, press the following
number combinations to
enter the equipment’s code
number (see the chart
below.)
Notes
• If your video equipment is furnished with a COMMAND MODE selector, set this
selector to the same position as the setting code.
• If the equipment does not have a certain function, the corresponding button on the
remote will not operate.
• When you remove the batteries, the code number may revert to the factory setting.
To control
DVD
VTR1 (Beta)
VTR2 (8 mm)
VTR3 (VHS) MDP
CD
MD
Hold down VIDEO I/1 and press
00
01
02
03
04
06
07
V
/
v
/
B
/
b
/
ENTER

http://cxema.ru
– 20 –
V-EX29M39/EX29M87/EX34M97
RM-963
V-EX29M93/EX29M65
RM-964
26 Advanced Operations
Operating a VCR using the remote
Operating a DVD pla er using the remote
Operating an MDP using the remote
Operating a CD/MD using the remote
To
turn on/off
record
play
stop
fast forward (M)
rewind the tape (m)
pause
search the picture forward (M) or backward (m)
Press
VIDEO ?/1
N while pressing z.
N
x
>
.
X
Press again to resume normal playback.
> or .during playback. Release to resume
normal playback.
To
turn on/off
play
stop
pause
step through different tracks of a disc
display the title menu
display the menu
select the menu item
Press
VIDEO ?/1
N
x
X
Press again to resume normal playback.
> to step forward or . to step backward.
TITLE
MENU while holding down z.
V
/
v
/
B
/
b
while holding down z.
To turn on/off
play stop
pause
step through different tracks of a disc
Press
VIDEO ?/1
N
x
X
Press again to resume normal playback.
> to step forward or . to step backward.
To
turn on/off
play
stop
pause
go to the next/previous tracks
go forward (M)/
backward (m) quickly in a track
Press
VIDEO ?/1
N
x
X
Press again to resume normal playback.
> or .
> or .while holding down (.
Operating optional components (continued)
27
Adjusting Your Setup (M NU)
Adjusting Your Setup (MENU)
Level 1
“PICTURE”
“SOUND”
“PIP”
Adjusting Your Setup (MENU)
Return icon
CH PRESET icon
SETUP icon
SOUND icon
Name of the current
menu
PICTURE icon
Level 2
“DRC-M ”
“PICTURE MODE”
“ADJUST”
“WIDE MODE”
“GAME MODE”
“SOUND MODE”
“ADJUST”
“SURROUND”
“INTELLIGENT
VOL”
“POSITION”
“PIP”
“SWAP”
Level 3/Function
Select the “DRC-M ” mode:
“DRC1250” t “PROGRESSIVE”
Select the picture mode:
“DYNAMIC” t “STANDARD” t “HI- INE” t
“PERSONAL” t “ADJUST”
Adjust the “PERSONAL” option:
“PICTURE” t “COLOR” t “BRIGHT” t “HUE” t
“SHARP”
Change the picture size.
Adjust the picture settings for video games.
Select the sound mode:
“DYNAMIC” t “DRAMA” t “SO T” t
“PERSONAL” t “ADJUST”
Adjust the “PERSONAL” option:
“BASS” t “TREBLE” t “BALANCE” t “BBE”*
Select the “SURROUND” mode:
“TruSurround” t “O ”
Adjust volume automatically.
Change the position of the sub screen.
Display a sub screen within the main picture.
Exchange pictures between main screen and sub screen.
Introducing the enu syste
The MENU button lets you open a menu and change the settings of your TV. The
following is an overview of the menu system.
Menu level 3
Menu level 2
Guide mark icon
Menu level 1
PIP icon
continued
LANGUAGE :
COL OR SYS :
SETUP
PROGRAM SE
PIC ROTAT I
ENGL I SH
OMEC ODE : O