Sony TRINITRON KV-HR29M61 User manual

HISTORY
When clicking an item, it’s detail is displayed.
Date SUPP./CORR. Description of SUP/COR Change of
main text
2004.01 NEW –
Model Name: KV-HR29M61/HR29N90/
HR34M61/HR34N90
SERVICE MANUAL
Part No. : 9-965-396-01

CHASSIS SERVICE MANUAL
MODEL COMMANDER DEST. CHASSIS NO.
–––––– –––––––––––– ––––– ––––––––––– MODEL COMMANDER DEST. CHASSIS NO. –––––– –––––––––––– ––––– –––––––––––
AX-1
KV-HR29M61 RM-1007 GE SCC-M15C-A
KV-HR29N90 RM-1011 Taiwan SCC-M19D-A
KV-HR34M61 RM-1007 GE SCC-M15B-A
KV-HR34N90 RM-1011 Taiwan SCC-M19C-A
TRINITRON COLOR TV
R
RM-1007 RM-1011 KV-HR29M61/HR29N90/HR34M61/HR34N90
TV
M
E
M
O
R
Y
S
T
I
C
K
C
E
N
T
E
R
S
P
VIDEO
MODE
DRC-MF
HD/DVD
123
456
78
0
9
JUMP
PROG
OPTION RESET
A/B
PROG
INDEX
MENU
V CENTERPALETTE
T
W
I
N
P
R
O
G
+
T
W
I
N
P
R
O
G
–

– 2 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
Specifications
Power requirements 220–240 V AC, 50/60 Hz (GE model), 110 V AC, 60 Hz (Taiwan model)
Power consumption (W) Indicated on the rear of the TV.
Television system B/G, I, D/K, M (GE model), M (Taiwan model)
Color system PAL, PAL 60, NTSC4.43, NTSC3.58, SECAM (GE model)
Available language for English, Farsi, French
Teletext (GE model)
Stereo/Bilingual system NICAM Stereo/Bilingual D/K, I, B/G; A2 Stereo/Bilingual (German) B/G
Channel coverage
B/G (GE model) VHF : E2 to E12 / UHF : E21 to E69 / CATV : S01 to S03, S1 to S41
I (GE model) UHF : B21 to B68 / CATV : S01 to S03, S1 to S41
D/K (GE model) VHF : C1 to C12, R1 to R12 / UHF : C13 to C57, R21 to R60 / CATV : S01 to S03, S1 to S41, Z1
to Z39
MVHF : A2 to A13 / UHF : A14 to A79/CATV : A-8 to A-2, A to W+4, W+6 to W+84 (GE model)
VHF : 2 - 13 / UHF : 14 - 69/CATV : 1- 125 (Taiwan model)
8(Antenna) 75-ohm external terminal
Audio output (Speaker) 7.5W + 7.5W
3D Woofer 15W
Number of terminal
(Video) Input: 4 Output: 1 Phono jacks; 1 Vp-p, 75 ohms
(Audio) Input: 6 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y: 1 Vp-p, 75 ohms, unbalanced, sync negative
C: 0.286 Vp-p, 75 ohms
(Component Input: 2 Phono jacks
Video) Y: 1 Vp-p, 75 ohms, sync negative
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
Audio: 500 mVrms
(G/B/R/HD/ Input: 1 Phono jacks
VD Video) G: 0.7 Vp-p, 75 ohms, B: 0.7 Vp-p, 75 ohms,
R: 0.7 Vp-p, 75 ohms
HD: 0.7 Vp-p, 75 ohms, VD: 0.7 Vp-p, 75 ohms
(Center Input:1 120 W max., 8 ohms
Speaker)
i(Headphones) Output: 1 Stereo minijack
Picture tube 34in. 29in.
Tube size (cm) 86 72
(measured diagonally)
Screen size (cm) 80 68
(measured diagonally)
Dimensions (w/h/d, mm) 898 x 706 x 575 775 x 617 x 506
Mass (kg) 85 58
Design and specifications are subject to change without notice.

– 3 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
(CAUTION)
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE
ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR CAR-
BON PAINTED ON THE CRT, AFTER REMOVING THE ANODE.
WARNING!!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD, BE-
CAUSE OF LIVE CHASSIS.
THE CHASSIS OF THIS RECElVER IS DIRECTLY CONNECTED
TO THE AC POWER LINE.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK !ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
THESECOMPONENTS WITH SONY PARTS WHOSE PART NUM-
BERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-
MENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT
ARE CRITICAL TO SAFEOPERATION ARE IDENTIFIED IN THIS
MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITI-
CAL COMPONENTS ARE REPLACED OR IMPROPER OPERA-
TION IS SUSPECTED.
TABLE OF CONTENTS
Section Title Page
–––––– –––– ––––
1. SELF DIAGNOSIS FUNCTION ........................... 5
2. DISASSEMBLY
2-1. REAR COVER ASSEMBLY ............................ 9
2-2. CHASSIS ASSEMBLY ..................................... 9
2-3. SERVICE POSITION ........................................ 9
2-4. SPEAKER BOX ASSEMBLY .......................... 9
2-5. T (GE model) AND UG BOARDS ................... 10
2-6. BM AND MG BOARDS ................................... 10
2-7. G1 (GE model) AND A BOARDS .................... 10
2-8. D BOARD .......................................................... 11
2-9. SF BOARD ......................................................... 11
2-10. H3, H4, H5 AND HMG BOARDS .................... 11
2-11. HARNESS ARRANGEMENT .......................... 12
2-12. REMOVAL OF ANODE-CAP .......................... 13
2-13. CRT ..................................................................... 14
3. SERVICE MODE
3-1. METHOD OF SETTING THE SERVICE
ADJUSTMENT MODE ..................................... 15
3-2. SERVICE MODE ADJUSTMENT ................... 15
3-3. MEMORY WRITE CONFIRMATION
METHOD ........................................................... 15
3-4. ADJUSTING BUTTONS AND INDICATOR . 15
3-5. SERVICE MODE LIST ..................................... 16
4. SET-UP ADJUSTMENTS
4-1. INTIALIZING SFC DATA ............................... 47
4-2. BEAM LANDING ............................................. 47
4-3. CONVERGENCE ADJUSTMENT ................... 48
4-4. G2 (SCREEN) ADJUSTMENT ......................... 50
4-5. FOCUS ADJUSTMENT 1 ................................. 50
4-6. NECK ASSY TWIST ADJUSTMENT ............. 51
4-7. PICTURE DISTORTION ADJUSTMENT ....... 51
4-8. SFC COARSE ADJUSTMENT ......................... 51
4-9. SFC FINE ADJUSTMENT ................................ 53
4-10.P&P SUB CONTRAST
ADJUSTMENT (VIDEO) .................................. 54
4-11.P&P SUB-HUE AND SUB-COLOR
ADJUSTMENT (VIDEO) .................................. 54
4-12.WHITE BALANCE ADJUSTMENT ................ 55
4-13.FOCUS ADJUSTMENT 2 ................................. 55
5. SAFETY RELATED ADJUSTMENTS
5-1. +B MAX VOLTAGE CONFIRMATION ......... 56
5-2. HV REGULATION CIRCUIT
ADJUSTMENT .................................................. 56
5-3. HV PRORTECTOR CIRCUIT CHECK ........... 56
5-4. IK PROTECTOR CIRCUIT
CHECK (D BOARD) ......................................... 56

– 4 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
Section Title Page
–––––– –––– –––– Section Title Page –––––– –––– ––––
6. DIAGRAMS
6-1. BLOCK DIAGRAM (1) ..................................... 57
BLOCK DIAGRAM (2) ..................................... 59
BLOCK DIAGRAM (3) ..................................... 61
BLOCK DIAGRAM (4) ..................................... 63
BLOCK DIAGRAM (5) ..................................... 65
BLOCK DIAGRAM (6) ..................................... 67
BLOCK DIAGRAM (7) ..................................... 69
BLOCK DIAGRAM (8) ..................................... 71
BLOCK DIAGRAM (9) ..................................... 73
BLOCK DIAGRAM (10)................................... 74
BLOCK DIAGRAM (11)................................... 75
BLOCK DIAGRAM (12)................................... 76
6-2. CIRCUIT BOARDS LOCATION ........................ 77
6-3. SCHEMATIC DIAGRAMS .................................. 77
(1) Schematic Diagram of A (1/3) Board ........ 79
(2) Schematic Diagram of A (2/3) Board ....... 81
(3) Schematic Diagram of A (3/3) Board ....... 83
(4) Schematic Diagram of BM (1/4) Board .... 85
(5) Schematic Diagram of BM (2/4) Board .... 87
(6) Schematic Diagram of BM (3/4) Board .... 89
(7) Schematic Diagram of BM (4/4) Board .... 91
(8) Schematic Diagram of C Board ................. 93
(9) Schematic Diagram of D (1/3) Board ....... 95
(10) Schematic Diagram of D (2/3) Board ....... 97
(11) Schematic Diagram of D (3/3) Board ....... 99
(12) Schematic Diagram of HMG, H3 Board .... 101
(13) Schematic Diagram of H4, H5 Board ........ 103
(14) Schematic Diagram of MG (1/3) Board..... 105
(15) Schematic Diagram of MG (2/3) Board..... 107
(16) Schematic Diagram of MG (3/3) Board..... 109
(17) Schematic Diagram of MS2 (1/3) Board ... 111
(18) Schematic Diagram of MS2 (2/3) Board ... 113
(19) Schematic Diagram of MS2 (3/3) Board ... 115
(20) Schematic Diagram of SF Board ............... 117
(21) Schematic Diagram of T Board.................. 119
(22) Schematic Diagram of UG (1/2) Board ..... 121
(23) Schematic Diagram of UG (2/2) Board ..... 123
(24) Schematic Diagram of W Board ................ 125
6-4. PRINTED WIRING BOARDS ............................. 127
• A Board ............................................................ 127
• BM Board ......................................................... 129
• C Board ............................................................ 131
• D Board ............................................................ 133
• G1, HMG, H3 Board ........................................ 135
• H4, H5 Board ................................................... 137
• MG Board (A side) .......................................... 139
• MG Board (B side) .......................................... 141
• MS2 Board ....................................................... 143
• SF Board .......................................................... 145
• T Board............................................................. 147
• UG Board (A side) ........................................... 149
• UG Board (B side) ........................................... 151
• W Board ........................................................... 153
6-5. WAVEFORMS ...................................................... 154
6-6. SEMICONDUCTORS ........................................... 155
7. EXPLODED VIEWS
7-1. CHASSIS SECTION .......................................... 157
7-2. SUPER WOOFER BLOCK ............................... 159
7-3. CRT SECTION .................................................. 160
7-4. BEZEL SECTION .............................................. 161
8. ELECTRICAL PARTS LIST................................. 162
• A Board ............................................................ 162
• BM Board ......................................................... 167
• C Board ............................................................ 173
• D Board ............................................................ 174
• G1 Board .......................................................... 180
• H3 Board .......................................................... 181
• H4 Board .......................................................... 181
• H5 Board .......................................................... 182
• HMG Board ...................................................... 182
• MG Board ........................................................ 183
• MS2 Board ....................................................... 188
• SF Board .......................................................... 191
• T Board............................................................. 193
• UG Board ......................................................... 194
• W Board ........................................................... 198

– 5 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
1. Summary of Self-Diagnosis Function
•This device includes a self-diagnosis function.
•In case of abnormalities, the 1or STANDBY/WAKE UP indicator automatically blinks. It is possible to predict the
abnormality location by the number of blinks. The Instruction Manual describes blinking of the 1 or STANDBY/WAKE UP
indicator.
•If the symptom is not reproduced sometimes in case of a malfunction, there is recording of whether a malfunction was gener-
ated or not. Operate the remote command to confirm the matter on the screen and to predict the location of the abnormality.
2. Diagnosis Items and Prediction of Malfunction Location
•When a malfunction occurs the 1 or STANDBY/WAKE UP indicator only blinks for one of the following diagnosis items.
In case of two or more malfunctions, the item which first occurred blinks. If the malfunctions occurred simultaneously, the item
with the lower blink count blinks first.
• The screen display displays the results regarding all the diagnosis items listed below. The display “ 0 ” means that no malfunc-
tions occurred.
Diagnosis Item
Number of times
1 or STANDBY/WAKE UP
indicator blinks
Probable Cause Location Detected Symptoms
+B overcurrent (OCP) 2 times T8001 (FBT) Rare short-circuit etc. (D board)
Q5001 (H-OUT), Q5006 (D board)
Has entered standby mode.
(Relay is off when the power
turns on.)
+B overvoltage (OVP) 3 times
+B load open (D board) R6570 Open
PH8003, control system malfunction L2603
Open
Has entered standby mode.
Vertical deflection stopped
(V-STOP) 4 times IC5101 (V. OUT) (D board) IC401
(CXA2170Q) (MG board) Has entered standby mode.
IK error (AKB ERROR) 5 times
VIDEO OUT IC malfunction IC9001, 9002,
9003 (C board) IC401 (CXA2170Q)
(MG board)
Has not entered standby mode.
Low-B error 6 times Sub power supply system load shorted etc.
(A board) Has entered standby mode.
Horizontal deflection
stopped (H-STOP)
Audio Protector
7 times IC401 (CXA2170Q) (MG board) Q5404
(S-COR-OUT), Q5001 (H-OUT), Q5006
8 times IC2000, 2001 malfunction (A board)
Has entered standby mode.
Has entered standby mode.
Zero Cross DET error 9 times RY6000 Power relay melting down (A board)
Has not entered standby mode.
High-Voltage stopped
(HV-PROT) 10 times T8001 (FBT) rare short-circuit (D board)
IC8002, Q8013, 8014, R8051 (D board) Has entered standby mode.
SECTION 1
SELF DIAGNOSIS FUNCTION

– 6 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
3. Blinking count display of 1or STANDBY/WAKE UP indicator
Lamp OFF :
3.0 seconds
Lamp ON : 0.3 seconds
Lamp OFF : 0.3 seconds
Release of 1or STANDBY/WAKE UP indicator blinking.
• The STAND BY indicator blinking display is released by turning OFF the power switch
on the TV main unit or removing the plug from the power.
But in the RLY ERR (10 times blinking), do not release by tuning power off.
For details, refer to the item 1-6.
*One blink is not used for self-diagnosis.
•EXAMPLE
<Diagnosis Items> <Number of Blinks>
• +B overcurrent 2 times
• +B overvoltage 3 times
• Vertical deflection stop 4 times
< FRONT PANEL >
GE model
1indicator
STANDBY/WAKE UP
Taiwan model
AUTOPROG
MENU
L(MONO) R
4
PROG
4. Self-diagnosis screen displays
•In cases of malfunctions where it is not possible to determine the symptom such as when the power goes off occasionally or when
the screen disappears occasionally, there is a screen display on whether the malfunction occurred or not in the past (and whether
the detection circuit operated or not) in order to allow confirmation.
<Screen Display Method>
•Quickly press the remote command button in the following order from the standby state.
˘
Be aware that this differs from the method of
entering the service mode ( + ).
bbb
5–=/1
<GE model>
<Taiwan model>
• "G" : OK, "NG" : DETECTS ONCE OR MORE
• THE 10 DIGITS OF NUMERALS ARE FOR CHECKING,
NO RELATION TO DIAGNOSIS.
• 101 : NO LED BLINKING FOR WDT.
"0" : NUMBER OF DETECTION.
Self-diagnosis screen display

– 7 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
5. After the self-diagnosis operation
•The results display is not automatically cleared. In case of repairs and after repairs, check the self-diagnosis screen and be sure
to return the results display to “ 0 ”.
• If the results display is not returned to “ 0 ” it will not be possible to judge a new malfunction after completing repairs.
<Method of Clearing Results Display>
<Method of Ending Self Diagnosis Screen>
• When ending the self-diagnosis screen completely, turn the power switch OFF on the remote commander or the main unit.
1. Power off (Set to the standby mode)
2. b5 b+ b(Service Mode) <GE model>
3. Channel 8 b0 (Test reset = Factory preset condition)
=/1
<Taiwan model>
AUDIO PROT
(FROM A BOARD)
LOW-B ERR
(FROM A BOARD)
HV-PROT
(FROM D BOARD)
AC-RLY
(TO A BOARD)
OCP
(FROM A, D BOARD)
MAIN MICRO-
COMPUTER
IC101
M306V2
I2C BUS
YCJ IC201
CXA-2170Q
OVP
HV PROT
OCP
AKB
H-STOP
V-STOP
PF
MICRO-
COMPUTER
IC102
OVP
(FROM A, D BOARD)
I2C BUS
• I2C YCJ RETURN DATA
11111111
LED
BLINKING
TIMES
MG BOARD
SYMPTOM
2
3
4
5
6
7
8
9
10
+B OCP
+B OVP
V-STOP
AKB
LOW-B ERROR
H-STOP
AUDIO PROT
Z DET
HV PRT

– 8 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
+B OCP If the IC701 Pin 44 (+B OCP DET) is high 2 seconds, turn AC-RELAY low (P-OFF) and make STANDBY
LED blinks twice.
+B OVP If the IC701 Pin 45 (+B OVP DET) is high 2 seconds, turn AC-RELAY low (P-OFF) and make STANDBY
LED blinks three times.
V-STOP If the return data Bit0 (VNG) from CXA2150Q is “1” while 2 seconds, turn AC-RELAY low (P-OFF) and
make STANDBY LED blinks four times.
AKB If the return data Bit2 (IKREF) from CXA2150Q is “0” and there is no change for 20 seconds, make
STANDBY LED blinks five times.
At this time, AC-RELAY continues to high.
LOW-B ERROR If the IC701 Pin 69 (AC-RELAY) is high and the Pin 43 (LOW-B ERROR DET) is low while 5 seconds,
turn AC-RELAY low (P-OFF) and make STANDBY LED blinks six times.
H-STOP If the return data Bit1 (HNG) from CXA2170 is “1” while 2 seconds, turn AC-RELAY low (P-OFF) and
make STANDBY LED blinks seven times.
W. D. T. Observes the watch dock timer (BUS COMMUNICATION ERROR DET) bus communication. If errors are
detected, counts up and reform the bus communication and displays the number of time.
(No LED blinking).
AUDIO PROT In case of Pin 85 of IC101 (AUDIO PROT DET) turns high 60msec twice at a time, makes AC-RELAY
turns low (Power off) and STANDBY-LED blinks 8 times.
HV-PROT In case of Pin 33 of IC101 (HV-PROT DET) turns high 10 seconds continuously in normal operation or in
BS fixed Stand-by, makes AC-RELAY turns low (Power off) and STANDBY-LED blinks 10 times.
Z DET There are two causes for Zero Cross Error.
Normally the pulse doubled AC power supply frequeny is fed to Pin 8 of IC101. But in case of the
abnormal pulse is fed, it makes AC-RELAY turns low (Power off) and STANDBY-LED blinks 9
times.
In this case, “1” is not displayed in ’9. Z DET’ column in the self-diagnosis mode.

– 9 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
SECTION 2
DISASSEMBLY
2-1. REAR COVER ASSEMBLY 2-3. SERVICE POSITION
2-2. CHASSIS ASSEMBLY 2-4. SPEAKER BOX ASSEMBLY
1Claw
1Claw Chassis assembly
2
1Three screws (+BVTP 4x16)
1Three screws
(+BVTP 4x16)
1Three screws
(+BVTP 4x16)
1Screw (+BVTP 4x16)
1Four screws (+BVTP 4x16)
2Rear cover assembly
Turn the chassis assembly
in the arrow direction, and
stand it its right side on the
bottom.
A support
1Connector
3Speaker box dssenbly
2Two screws (+ TWHTP 4x25)

– 10 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
2-6. BM AND MG BOARDS
2-7. G1 (GE model) AND A BOARDS
2-5. T (GE model) AND UG BOARDS
8Screw
(+BVTP 3x12)
8Screw
(+BVTP 3x12)
9Two connectors
(CN5802, 5803)
6Connectors
(CN1501)
5U bracket
7UG board
0T board
(GE model)
4Power cord
1Five screws
(+BVTP 3x12)
1Screw
(+BVTP 3x12)
2Screw
(+PSW 3x8)
3
3
BM board
(with MS2 board)
MG board
CN0050
1Screw
(+PSW3x8)
CN0004
CN0301
CN0006
CN0406
CN0405
CN0401
CN0402
CN0301
3BM bracket
2Two screws
(+BVTP3x12)
CN2017
CN2001
CN6006
CN6100 CN6101
CN6010
CN6005
CN6001
RF splitter
8Three screws
(+BVTP 3x12)
8Two screws
(+BVTP 3x12)
A board
7Connectors
CN2006, 2007, 2011, 2012
6Connectors
5Connector
9
1Three screws
(+BVTP 3x12)
3Two screws
(+BVTP 3x12)
4G1 board
2G1 bracket
(with G1 board)

– 11 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
2-10. H3, H4, H5 AND HMG BOARDS
2-9. SF BOARD2-8. D BOARD
1Connectors
2Screw
(+BVTP 3x12)
3
D board
CN6400
CN5012
CN5003
CN5010
CN5019
CN5017
1Connectors
2Three screws
(+BVTP 3x12)
SF board
CN3809
CN3808
CN3806
CN3807
CN3803CN3804
CN3805
3
1Connectors
CN1054, 1055
1Connectors
CN1502
4Connectors
CN7204
7Connectors
CN1001,
to 1003
2Screw
(+BVTP 3x12)
5Screw
(+BVTP 3x12)
8Screw
(+BVTP 3x12)
qa Screw
(+BVTP 3x12)
3H4 board
6HMG board
9H3 board
qs H5 board
0Connectors
CN9302, 9303

– 12 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
2-11. HARNESS ARRANGEMENT
CN3806-3809
COIL,NA ROTATION
CN9002
CN9009
CN0301
CN9001
CN9104, 9101
CN5010
CN9001
CN6013
CN6005 CN6000
CN6006
CN6100
CN6101

– 13 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
2-12. REMOVAL OF ANODE-CAP
NOTE : After removing the anode, short circuit the anode of the picture tube and
the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.
•REMOVING PROCEDURES
1Do not damage the surface of anode-caps with sharp shaped objects.
2Do not press the rubber too hard so as not to damage the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built into the rubber.
3Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the rubber.
•HOW TO HANDLE AN ANODE-CAP
3When one side of the rubber cap is separated from the anode button, the anode-cap
can be removed by turning up the rubber cap and pulling it up in the direction of the
arrow c.
2Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.
1Turn up one side of the rubber cap in the direction indicated by the arrow a.
a
a
b
b
c

– 14 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
2-13. CRT
NOTE: After removing the anode, short circuit the anode of the picture tube
and the anode cap to the metal chassis, CRT shield or carbon paint
on the CRT.
8CRT supporter
1Screws
(+PWH 4x16)
3Anode cap
6Neck assembly
5C board 7Deflection
yoke
qa Extension
springs
qs Screws
(Crown washer +TP 7x40)
qd CRT
CUSHON
4Chassis assembly
0Degauss coil
9DGC holder
0Degauss coil
2Speaker box assembly

– 15 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
SECTION 3
SERVICE MODE
TV
M
E
M
O
R
Y
S
T
I
C
K
C
E
N
T
E
R
S
P
VIDEO
MODE
DRC-MF
HD/DVD
123
456
78
0
9
JUMP
PROG
OPTION RESET
A/B
PROG
INDEX
MENU
V CENTERPALETTE
T
W
I
N
P
R
O
G
+
T
W
I
N
P
R
O
G
–
3. The SCREEN displays the item being adjusted.
4. Press 1or 4on the Remote Commander to select the
category.
5. Press 3or 6on the Remote Commander to change the data.
6. Press 2or 5on the Remote Commander to select the
adjustment item.
7. If you want to recover the latest values press 7then -to read
the memory.
8. Press [MUTING] or then -to write into memory.
9. Turn power off.
Note: Press 8then -on the Remote Commander to initialize
or turn set off and on to exit.
3-3. MEMORY WRITE CONFIRMATION METHOD
1. After adjustment, turn power off with the remote commander.
2. Turn power on and set to Service Mode.
3. Call the adjusted items again and confirm they were adjusted.
3-1. METHOD OF SETTING THE SERVICE ADJUSTMENT
MODE
SERVICE MODE PROCEDURE
1. Standby mode. (Power off)
2. n5 n(+) n=/1 <GE model>
<Taiwan model>
on the Remote Commander.
(Press each button within a second.)
3-2. SERVICE MODE ADJUSTMENT
3-4. ADJUSTING BUTTONS AND INDICATOR
RM-1007
Adjustment item up
Category up
Data up
Data down
Category down
Adjustment item down
(+)
%
=/1
-
Read
RM-1011

– 16 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
3-5.SERVICE MODE LIST
OSD
No. Name
00 OSV 32
01 OSH 13
02 FW1 07
03 FW2 20
04 VO
F
*1
Standards *1
No. Name
04 VO
F
32 32 32 32 32 32 32
No. Name
04 VO
F
32 32 32 32 32 32 32
No. Name
04 VO
F
32 32 32 32 32 32 32
No. Name
04 VO
F
32 32 32 32
VCOMP120
Functionality
Functionality
MS
VCOMP VCOMP60 VCOMP100
ZOOM120 INDEX50 INDEX60
Functionality FAVORITE50 FAVORITE60 TWIN50 TWIN60 HD50 HD60
WDZM120 ZOOM50 ZOOM60 ZOOM100
FULL120 WDZM50 WDZM60 WDZM100
Functionality FULL50 FULL60 FULL100
OSD ODD/EVEN Field Window Setup #1
OSD ODD/EVEN Field Window Setup #2
OSD V Position (Offset) Wide/50/60/100/120/HD/Twin/Favorite/Index
Remarks
OSD V Position
OSD H Position
Functionality Range Standards Function
MSP
No. Name
00 WST 21 W/G Stereo Threshold
01 WBT 236W/G Bilingual Threshold
02 WL
L
05 W/G Monaural Threshold
03 WAC 01 W/G Agreement Count
04 WDL 48 W/GSearch Delay
05 ND
L
32 NICAMSearch Delay
06 SD
L
16 Stereo status Read Delay
07 AGC 01 AGC Switch Auto/Constant
08 RE
L
40 AGC Gain at Constant Mode
09 CR
M
00 Carrier muting on/off
10 ACO 01 Audio Clock out on/off
11 FP 27 FM Prescale for non-M system
12 FPM 50 FM Prescale for M system
13 FH 54 FM Prescale for HDEV
14 FHM 101 FM Prescale for HDEV and M
15 WG
P
28 W/G Prescale
16 NI
P
127 NICAM Prescale
17 ERR 80 Auto FM switch Threshold
18 VO
L
48 Loud Speaker gain 0700h to 07FFh
Remarks
Functionality Range Standards Function

– 17 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
TEXT
No. Name
00 TXH 35 Teletext Horizontal Display Position
01 TXV 63 Teletext Vertical Display Position
02 THD 56 Teletext H-sync Active Edge Shift
03 TVD 00 Teletext V-sync Active Edge Shift
04 HP
L
00 Teletext H-sync Polarity Configuration
05 VP
L
00 Teletext V-sync Polarity Configuration
06 FP
L
01 Teletext Field Polarity Configuration
07 FMD 03 Teletext Fastext/TOP Force Mode
08 TBR 15 Teletext RGB Brightness
09 NOP 02 Teletext National Option Table Configuration
10 TCH 02 Teletext TwistedCharacter Set Configuration
Remarks
Functionality Range Standards Function
PIC
No. Name
00 PIC * 1 Picture Mod
e
01 COL * 1 Picture Mod
e
02 BRI * 1 Picture Mod
e
03 HUE *1 Picture Mod
e
04 SHP * 1 Picture Mod
e
05 PIO
F
*2 MS/NORMAL/MULTI/OTHER
Standards *1
No. Name Dynamic Standard Hi-Fine Personal
00 PIC 100 80 60 50
01 COL 60 605050
02 BRI 43 505050
03 HUE 50 50 50 50
04 SHP 50 505050
Standards *2
No. Name MS Normal(4:4) HD Twin/Index/Pap Other
05 PIO
F
31350
Picture OffsetFunctionality
User Sharp
Picture Offset (Picture * (20-data)/20*Eco(75%)
PictureModeFunctionality
User Picture
User Color
User Bright
User Hue
Functionality Range Standards Remarks
Function
SO
U
No. Name
00 BAS *1 Sound Mod
e
01 TRE *1 Sound Mod
e
Standards *1
No. Name Dynamic Drama Soft Personal
00 BAS 50 505050
01 TRE 50 50 50 50
User Treble
Sound ModeFunctionality
RemarksFunction
User Bass
Functionality Range Standards
DRC
No. Name
00 CLAR *1 User DRC Palette Initial number Clarity
01 REA
L
*1
Standards *1
No. Name Dynamic Std/HiFine/Per Dynamic Std/HiFine/Per Dynamic Std/HiFine/Per Dynamic Std/HiFine/Per Dynamic Std/HiFine/Per
00 CLAR 01 01 50 50 80 80 01 01 50 50
01 REA
L
25 25 55 55 90 90 25 25 55 55
No. Name Dynamic Std/HiFine/Per Dynamic Std/HiFine/Per Dynamic Std/HiFine/Per Dynamic Std/HiFine/Per
00 CLAR 80 80 01 01 50 50 80 80
01 REA
L
90 90 25 25 55 55 90 90
DRC Palette (Video Custom2)
Functionality DRC Palette (Video Cust om3) DRC Palette (Comp Custom1) DRC Palette (Comp Custom2) DRC Palette (Comp Custom3)
Functionality DRC Palette (TV Custom1) DRC Palette (TV Custom2) DRC Palette (TV Custom3) DRC Palette (Video Custom1)
Function
Functionality Range Standards
User DRC Palette Initial Number Reality
Remarks

– 18 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
LUMA
No. Name
0BROF0-7 *1
1GAMM0-7 *1
2GAMS0-15 *2
3RGAM0-15 *2
4GGAM 0-15 *2
5BGAM0-15 *2
6BLK0-7 *1
7APED0-3 *3
8DCTR0-15 *3
9ABLM0-3 *3
Standards *1
RF / CV / YC / COMP
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0BROF 00000044111133
1GAMM 44444444444444
6BLK 66666677777777
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0BROF 55533344441111
1GAMM 33333344444444
6BLK 44444444445555
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0BROF 00000000000000
1GAMM 00000000000000
6BLK 00000000000000
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0BROF 55533344441111
1GAMM 33333344444444
6BLK 44444444445555
RGB / MS / Twin
Twin
480_60I 576_50I 480_60P 576_50P 720_60P 720_50P 1080_60I 1080_50I Index Full Popup Player Movie All Format
0BROF 44111133111110
1GAMM 44444444444444
6BLK 77777777555555
Twin
480_60I 576_50I 480_60P 576_50P 720_60P 720_50P 1080_60I 1080_50I Index Full Popup Player Movie All Format
0BROF 44441111111111
1GAMM 44444444444444
6BLK 44445555555555
Twin
480_60I 576_50I 480_60P 576_50P 720_60P 720_50P 1080_60I 1080_50I Index Full Popup Player Movie All Format
0BROF 00000000000000
1GAMM 00000000000000
6BLK 00000000000000
Twin
480_60I 576_50I 480_60P 576_50P 720_60P 720_50P 1080_60I 1080_50I Index Full Popup Player Movie All Format
0BROF 44441111111111
1GAMM 44444444444444
6BLK 44445555555555
Standards *2
No. Name GAMMA0 GAMMA1 GAMMA2 GAMMA3 GAMMA4 GAMMA5 GAMMA6 GAMMA7
2GAMS13 13131313131313
3RGAM 045678910
4GGAM 045678910
5BGAM 045678910
Standards *3
No. Name BLK0BLK1BLK2BLK3BLK4BLK5BLK6BLK7
7APED 01332132
8DCTR 0581510 5 10 10
9ABLM 00010011
No. Name
Personal
RGB MS
No. Name
Hi-Fine
RGB MS
No. Name
Standard
RGB MS
Functionality
No. Name
Dynamic
RGB MS
Range Standards
720_60P 720_50P 1080_60I 1080_50I
No. Name
Personal
RF CV/YC Comp
480_60I 576_50I 480_60P 576_50P
720_60P 720_50P480_60P 576_50P 1080_60I 1080_50I
No. Name
Hi-fine
RF CV/YC Comp
480_60I 576_50I
720_60P 720_50P 1080_60I 1080_50I
No. Name
Standard
RF CV/YC Comp
480_60I 576_50I 480_60P 576_50P
720_60P 720_50P 1080_60I 1080_50I
No. Name
Dynamic
RF CV/YC Comp
480_60I 576_50I 480_60P 576_50P

– 19 –
KV-HR29M61/HR29N90/HR34M61/HR34N90
RM-1007 RM-1011 RM-1007 RM-1011
COLR
No. Name
0CLOF0-7 *1
1HUOF 0-7 *1
2RDRV0-63 41
3GDRV 0-63 30
4BDRV0-63 35
5RCUT0-63 41
6GCUT0-63 31
7BCUT0-63 24
8SBRT0-63 25
9DCOL0-3 1
10 WBSW 0-1 *2
11 SBOF 0-7 *2
12 RDOF 0-63 *2
13 GDOF 0-63 *2
14 BDOF 0-63 *2
15 RCOF 0-63 *2
16 GCOF 0-63 *2
17 BCOF 0-63 *2
18 AXIS 0-3 *1
19 R-YR 0-15 *3
20 R-YB 0-15 *3
21 G-YR 0-15 *3
22 G-YB 0-15 *3
Standards *1
RF / CV / YC / COMP
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0CLOF 66655566665555
1HUOF 33133132333333
18 AXIS 33133131313131
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0CLOF 11311313444444
1HUOF 33133132333333
18 AXIS 33133131313131
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0CLOF 33333333333333
1HUOF 33333333333333
18 AXIS 33133131313131
480_60I 480_60I 576_50I 480_60I 480_60I 576_50I
NTSC PAL PAL NTSC PAL PAL
0CLOF 11311313444444
1HUOF 33133132333333
18 AXIS 33133131313131
RGB / MS / Twin
Twin
480_60I576_50I 480_60P576_50P 720_60P720_50P 1080_60I 1080_50I IndexFullPopup Player Movie All Format
0CLOF 66665555777776
1HUOF 33333333333333
18 AXIS 31313131111111
Twin
480_60I576_50I 480_60P576_50P 720_60P720_50P 1080_60I 1080_50I IndexFullPopup Player Movie All Format
0CLOF 11444444444444
1HUOF 33333333333333
18 AXIS 31313131111111
Twin
480_60I576_50I 480_60P576_50P 720_60P720_50P 1080_60I 1080_50I IndexFullPopup Player Movie All Format
0CLOF 33333333333333
1HUOF 33333333333333
18 AXIS 31313131111111
Twin
480_60I576_50I 480_60P576_50P 720_60P720_50P 1080_60I 1080_50I IndexFullPopup Player Movie All Format
0CLOF 11444444444444
1HUOF 33333333333333
18 AXIS 31313131111111
No. Name
Personal
RGB MS
No. Name
Hi-Fine
RGB MS
No. Name
Standard
RGB MS
1080_50I
No. Name
Dynamic
RGB MS
576_50I 480_60P 576_50P 720_60P
720_50P 1080_60I576_50P 720_60P
720_50P 1080_60I
1080_50I
No. Name
Personal
RF CV/YC Comp
480_60I
576_50I 480_60P
720_50P 1080_60I 1080_50I
No. Name
Hi-Fine
RF CV/YC Comp
480_60I
576_50I 480_60P 576_50P 720_60P
720_50P 1080_60I 1080_50I
No. Name
Standard
RF CV/YC Comp
480_60I
576_50I 480_60P 576_50P 720_60P
Functionality Range Standards
No. Name
Dynamic
RF CV/YC Comp
480_60I