Sony Trinitron KV-T21TF2 User manual

©1997 by Sony Corporation
3-861-104-11 (1)
Trinitron Color TV

Operating Instructions
KV-T21TF2

2

3
1
– PROGR +
SELECT
PROGR
VHF LOW D/K
SELECT

4

Getting Started -EN
5
WARNING Table of contents
• Dangerously high voltages are present inside the TV.
• Operate the TV only at 110-240 V AC.
• Do not open the cabinet and the rear cover of the TV.
Refer servicing to qualified personnel.
• To prevent fire or shock hazard, do not expose the TV
to rain or moisture.
• Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by qualified
personnel only.
• Do not block the ventilation openings.
• Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
• Do not install the TV in hot, humid or excessively
dusty places.
• Do not install the TV where it may be exposed to
mechanical vibrations.
• Do not keep the TV plugged in if you are not going to
use it for several days.
• Do not pull the power cord to disconnect the TV. Pull
it out by the plug.
• Use only the supplied screws (as shown on page 2) to
fasten the TV to the TV stand or to stabilize the TV
against a wall or a pillar. Use of other screws may
damage the TV.
Note on the remote commander
• The supplied remote commander is used on several models of
the TV. If you do not find instructions for some controls that
are on the remote commander, that means your TV does not
employ the features of those controls, e.g. .
Notes
• When you turn on the TV, you may hear the “boon” sound
that is caused by the demagnetization of the TV. This does not
indicate a malfunction.
• The picture color may become abnormal if you change the
direction of your TV. To obtain the normal picture color, press
Uon the TV to turn off the TV for five minutes and then turn it
on again.
• Design and specificafions are subject to change without notice.
Getting Started
6Connections
8Presetting channels
Operations
10 Watching the TV
12 Adjusting the picture and the sound
Additional Information
13 Troubleshooting
Back cover
Specifications
All contents are subject to change without notice.

Getting Started
6-EN
Connections
Getting Started
or
Connecting a VHF antenna or a combination VHF/UHF antenna
— 75-ohm coaxial cable (round)
Attach an optional IEC antenna connector to the 75-ohm coaxial cable.
Plug the connector into the (antenna) socket at the rear of the TV.
Rear of TV Rear of TV
On a wall

Getting Started -EN
7
Connecting optional equipment
You can connect optional audio/video equipment to your TV such as a VCR, multi disc player, camcorder, video
game, or stereo system.
Connecting video equipment using video input jacks
or
Ú
to …
(yellow)
-L (white)
-R (red)
to video and
audio outputs
: Signal flow
Camcorder
VCR
to video
and audio
outputs
: Signal flow
to …
(yellow)
-L (white)
-R (red)
Rear of TV
to antenna
output
Audio system
to …
(yellow)
-L (white)
-R (red)
to video and
audio inputs to audio inputs
VCR
to antenna socket
to antenna
output
to antenna socket
Rear of TV
Front of TV
OR
When connecting a monaural VCR
Connect the yellow plug to (VIDEO) and the black plug to -L (AUDIO-L MONO).
When connecting a VCR to the (antenna) terminal
Preset the signal output from the VCR to the program position 0.
When connecting video equipment to the …(VIDEO INPUT) jacks or the …(VIDEO IN) jacks
Do not connect video equipment to the …(VIDEO INPUT) jacks at the front and the …(VIDEO IN) jacks at the rear of your TV
simultaneously; otherwise the picture will not be displayed properly on the screen.
Connecting audio/video equipment using Ú(MONITOR/TV OUT) jacks
When recording through the Ú(MONITOR/TV OUT) jacks
If you change the channel or video input while recording with a VCR, the channel or video input you are recording will also be changed.
: Signal flow
RL(MONO)
RL
(MONO)
RL
(MONO)

Getting Started
8-EN
You can preset up to 100 TV channels in numerical
sequence from program position 1 using the buttons on
the remote commander or the TV.
You can preset TV channels quickly, automatically or
manually.
Quick channel presetting
1Press Uon the TV.
When the TV is turned on in standby mode, press
uon the remote commander.
2Press SELECT and PROGR + on the TV
simultaneously for one to two seconds.
Presetting channels
Front of TV
Remote commander
or
If the picture color is poor and/or the
sound is noisy
Select the appropriate TV system as follows:
1Press SELECT on the remote commander or the TV
until TV SYSTEM appears.
2Press +/– on the remote commander or .+/– on
the TV until the picture and sound become normal.
Notes
•If you do not know your local TV system, consult your nearest
authorized service center or dealer.
•The setting of the TV SYSTEM is memorized for each program
position.
Presetting channels manually
1Press SELECT on the remote commander or
the TV until TV SYSTEM appears on the
screen.
2Press +/– on the remote commander or .
+/– on the TV to select the TV system.
3Press SELECT on the remote commander or
the TV until AUTO PROGRAM appears on the
screen.
4Press +/– on the remote commander or .
+/– on the TV.
5Press +/– on the remote commander or .
+/– on the TV again.
or
or
u
Number
+/–
SELECT
PROGR +/–
or
or
PROGR
SELECT
– PROGR +
SELECT
1 2 3 1
TV SYSTEM
SELECT SELECT
ID/K B/G M
AUTO PROGRAM
SELECT SELECT
VHF LOW D/K
1
1 2 3 1

Getting Started -EN
9
6Press +/– on the remote commander or Á+/
– on the TV until the required channel
picture appears on the screen.
7Press SELECT on the remote commander or
the TV.
Disabling program positions
1Press PROGR +/– or number buttons on the
remote commander or PROGR +/– on the TV
until the unused or unwanted program
position appears on the screen.
2Press SELECT on the remote commander or
the TV until "MANUAL PROGRAM" appears
on the screen.
3Press +/– on the remote commander or Á+/
– on the TV.
4Press PIC MODE on the remote commander.
5Press SELECT on the remote commander or
the TV.
To preset the disabled program position again
Preset the channel quickly, automatically or manually.
or
To start presetting channels automatically
from the specified program position
Press PROGR +/– or number buttons on the remote
commander or PROGR +/– on the TV until the
required program position appears on the screen after
step 4.
Presetting channels manually
1Press SELECT on the remote commander or
the TV until "TV SYSTEM" appears on the
screen.
2Press +/– on the remote commander or Á +/–
on the TV to select the TV system.
3Press SELECT on the remote commander or
the TV until MANUAL PROGRAM appears on
the screen.
4Press +/– on the remote commander or Á+/
– on the TV.
5Press PROGR +/– or number buttons on the
remote commander or PROGR +/– on the TV
until the required program position
appears on the screen.
or
or
or
or
or
or
or
or
or
123
46
789
0
5
PROGR – PROGR +
TV SYSTEM
SELECT SELECT
ID/K B/G M
MANUAL PROGRAM
SELECT SELECT
123
46
789
0
5
PROGR
– PROGR +
VHF LOW D/K
1
SELECT SELECT

Operations
10-EN
1Press Uto turn on the TV.
When the TV is turned on in standby mode, press
uon the remote commander.
2Select the TV program you want to watch.
To select a program position directly
Press the number button.
To select a two-digit program position, press
“-/--” before the number buttons.
For example: to select program position 25, press
“-/--,” and then “2” and “5.”
To scan through program positions
Press PROGR +/– until the program position you
want appears.
3Press Á+/– to adjust the volume.
Watching the TV
VIDEO 1
MUTING
÷2 5
Operations
Turning off the TV
To turn off the TV temporarily
Press uon the remote commander. The uindicator
lights up.
To turn off the TV completely
Press Uon the TV.
If the power on the TV is turned off in standby mode,
the uindicator may remain alight for a while.
Watching the video input
Press ….
To watch TV
Press ;.
Muting the sound
Press ¤.
123
46
789
÷0
5
PROGR