Sony SLV-D300P Operating Instructions (SLVD300P) User manual

US Model SERVICE MANUAL
DVD PLAYER/
VIDEO CASSETTE RECORDER
SPECIFICATIONS
SLV-D300P
RMT-V501A
System
Laser
Semiconductor laser
Format
VHS NTSC standard
Video recording system
Rotary head helical scanning FM system
Video heads
Double azimuth four heads
Video signal
NTSC color, EIA standards
Tape speed
SP: 33.35 mm/s (1
inches/s)
EP: 11.12 mm/s (
inches/s)
LP: 16.67 mm/s (
inches/s),
playback only
Maximum recording/playback time
8 hrs. in EP mode (with T-160 tape)
Rewind time
Approx. 1 min (with T-120 tape)
Tuner section
Channel coverage
VHF 2 to 13
UHF 14 to 69
CATV A-8 to A-1, A to W, W+1 to W+84
Antenna
75-ohm antenna terminal for VHF/UHF
Audio characteristics
Frequency response
DVDVIDEO (PCM 96 kHz): 2 Hz to 44 kHz (±1.0
dB)/DVDVIDEO (PCM 48 kHz): 2 Hz to 22 kHz
(±0.5 dB)/CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio)
115 dB (LINE OUT (L/R) AUDIO jacks only)
Harmonic distortion
0.003 %
Dynamic range
DVD VIDEO: 103 dB/CD: 99 dB
Wow and flutter
Less than detected value (±0.001% W PEAK)
The signals from LINE OUT L/R (AUDIO) jacks are
measured. When you play PCM sound tracks with a 96
kHz sampling frequency, the output signals from the
DIGITAL OUT (OPTICAL or COAXIAL) jack are
converted to 48 kHz sampling frequency.
Inputs and outputs
LINE IN 1 and LINE-2 IN
VIDEO IN, phono jack (1 each)
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO IN, phono jacks (2 each)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO OUT, phono jacks (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
DIGITAL OUT
OPTICAL, Optical output jack
−18 dBm (wave length: 660 nm)
COAXIAL, phono jack
Output signal: 0.5 Vp-p, 75 ohms
COMPONENT VIDEO OUT (Y, Pb, Pr)
Phono jack
Y: 1.0 Vp-p/Pb, Pr: 0.7 Vp-p, 75 ohms
S-VIDEO OUT
4-pin, mini-DIN jack
Y: 1.0 Vp-p, unbalanced, sync negative
C: 0.286 Vp-p, load impedance 75 ohms
Timer section
Clock
Quartz locked
Timer indication
12-hour cycle
Timer setting
8 programs (max.)
38
716
11 16
General
Power requirements
120 V AC, 60 Hz
Power consumption
28 W
Operating temperature
0°C to 45°C (32°F to 113°F)
Storage temperature
−20°C to 60°C (−4°F to 140°F)
Operating humidity
25% to 80%
Dimensions including projecting parts and controls
(w/h/d)
Approx. 430 ×95 ×295 mm
(Approx. 17 ×3.7 ×12 inches)
MassApprox. 4.0 kg (Approx. 8.8 lbs)
Supplied accessories
Remote commander (1)
Size AA (R6) batteries (2)
75-ohm coaxial cable with F-type connectors (1)
Audio/video cord (pinplug ×3 ypinplug ×3) (1)
Design and specifications are subject to change without
notice.


— 2 —
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION,
BE SURE TO OBSERVE FROM A DISTANCE OF
MORE THAN 25 cm FROM THE SURFACE OF THE
OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED
LINE WITH MARK 0ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
CAUTION:
The use of optical instrument with this product will increase eye
hazard.
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µFAC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
LEAKAGETEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuringthe voltagedropacrossaresistorby means of aVOM
or battery-operated AC voltmeter. The “limit” indication is
0.75V, so analog meters must have an accurate low-voltagescale.
The Simpson 250 and Sanwa SH-63Trd are examples of a
passiveVOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend
their replacement.
5. Check the line cord for cracks and abrasion. Recommend the
replacement of any such line cord to the customer.
6. Check the B+ voltage to see it is at the values specified.
7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:

8-1
8. Repair Parts List
8-1 Exploded Views - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
8-1-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
8-1-2 VCR Mechanical Parts (Top Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
8-1-3 VCR Mechanical Parts (Bottom Side) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
8-1-4 DVD Mechanical Parts - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
8-2 Electrical Parts List - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
8-2
8-2
8-3
8-4
8-5
8-6
SLV-D300P

8-2
8-1-1 Cabinet Assembly
8-1 Exploded Views
NOTE:
•-XX, -X mean standardized parts, so they may
have some differences from the original one.
•Items marked “*” are not stocked since they
are seldom required for routine service. Some
delayshouldbe anticipatedwhenordering these
items.
•Themechanicalparts with noreference number
in the exploded views are not supplied.
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
19-885-037-40 ASSY PANEL FRONT (COMBO UC)
29-885-037-28 SPRING ETC-DOOR TRAY
39-885-037-27 DOOR TRAY
49-885-037-26 DOOR CASSETTE
59-885-037-13 SPRING ETC MASK
010 1-824-674-11 POWER CORD EP2 SPT-2
11 9-885-037-25 CASE (COMBO UC), UPPER
12 3-075-256-01 SCREW TAP 3X12
13 3-075-262-01 SCREW BH 4X12
14 3-078-566-01 SCREW TAP M3 L10 BLK
15 9-885-035-23 COMMANDER, STANDARD (RMT-V501A)
16 3-078-598-01 BATTERY COVER (COMBO GRAY)
(for RMT-V501A)
17 9-885-037-16 VHS DECK ASSY
not supplied
10
11 14
1
not supplied
13
23
4
not supplied
not supplied
5
not supplied
not supplied
not supplied
not supplied
17
DVD Mechanical Parts
not supplied
15
16
not supplied
not supplied
13
12
12
12
12
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.

8-3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
101 3-067-779-01 LEVER-#9 GUIDE
102 3-067-780-01 SPRING-#9 GUIDE
103 3-067-785-01 LEVER-T. BRAKE
104 3-067-786-01 SPRING-BRAKE
105 3-067-782-01 SPRING-TENSION LEVER
106 3-067-781-01 LEVER-TENSION
107 3-067-783-01 BAND-BREAK
108 3-067-788-01 HOLDER-FL CASS.
109 9-885-037-15 ASSY CLYNDER 6HD
110 3-084-091-01 SCREW TAP 2.6X5
111 3-075-254-01 SCREW ASSY MAC 3X6
112 3-067-784-01 LEVER-UNIT PINCH
8-1-2 VCR Mechanical Parts (Top Side)
109
111
112
114
125
115 116
117
118
113
110
120
101
102
124
106
105
104
123
103
121
107
108
not supplied
not supplied
not supplied
not supplied
not supplied not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not
supplied
not supplied
113 3-075-257-01 SCREW TAP 2.6X5
114 3-075-241-01 ASSY ACE HEAD
115 3-067-789-01 GUIDE-CASS. DOOR
116 3-075-021-01 AUTO HEAD CLEANER (G680)
117 3-075-022-01 AUTO HEAD CLEANER (G681)
118 1-763-836-11 LOADING ASSY, MOTOR
120 3-067-787-01 LEVER-FL DOOR
121 3-067-796-01 PLATE-GROUND DECK
123 3-075-046-01 DISK T REEL
124 3-075-047-01 DISK S REEL
125 3-079-356-01 POST #8 GUIDE ASSY

8-4
8-1-3 VCR Mechanical Parts (Bottom Side)
not supplied
not supplied
not supplied
not
supplied
not supplied not supplied
not
supplie
d
not
supplied
not supplied
151
152
154
153
151 3-067-790-01 BELT-PULLEY
152 1-796-432-11 MOTOR CAPSTAN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
153 3-075-259-01 SCREW CAP 2.6X6
154 3-075-260-01 SCREW MAC 3X3

8-5
8-1-4 DVD Mechanical Parts
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
201 9-885-037-24 TRAY DISC
202 9-885-037-20 MOTOR LOADING ASSY
203 3-078-583-01 BELT RECTANGULAR
0204 9-885-037-37 ASSY PICK UP
205 3-078-588-01 SHAFT PU
206 9-885-037-21 MOTOR-SPINDLE
208 3-078-592-01 SCREW TAP 2X6
209 9-885-037-35 RUBBER INSULATOR
210 9-885-037-22 MOTOR FEED ASSY
211 9-885-037-31 GEAR FEED A
212 9-885-037-32 GEAR FEED B
218 9-885-037-38 ASSY DVD DECK
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.

8-6
NOTE:
•Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
•-XX, and -X mean standardized parts, so they
mayhave somedifferencefromthe originalone.
•RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
•Not all of the parts are listed.
•Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
•CAPACITORS:
uF: µF
•COILS
uH: µH
8-2 Electrical Parts List
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
When indicating parts by reference number,
please include the board name.
DVD MAIN
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
DVD MAIN BOARD
***************
SC3A 3-075-255-01 SCREW TAP 3X8
< DIODE >
AD1 1-805-012-11 DIODE DAN202K
AD2 1-805-012-11 DIODE DAN202K
AD3 1-805-012-11 DIODE DAN202K
AD4 1-805-009-11 DIODE DAN217
AD5 1-805-012-11 DIODE DAN202K
AZ1 1-805-011-11 DIODE UDZ9.1B
AZ2 1-805-011-11 DIODE UDZ9.1B
AZ3 1-805-011-11 DIODE UDZ9.1B
AZ4 1-805-011-11 DIODE UDZ9.1B
DD1 1-805-013-11 DIODE DAP202K
DOZ1 1-805-011-11 DIODE UDZ9.1B
DOZ2 1-805-011-11 DIODE UDZ9.1B
VZ1 1-805-011-11 DIODE UDZ9.1B
VZ2 1-805-011-11 DIODE UDZ9.1B
VZ3 1-805-011-11 DIODE UDZ9.1B
VZ4 1-805-011-11 DIODE UDZ9.1B
VZ5 1-805-011-11 DIODE UDZ9.1B
VZ6 1-805-011-11 DIODE UDZ9.1B
VZ7 1-805-011-11 DIODE UDZ9.1B
VZ8 1-805-011-11 DIODE UDZ9.1B
VZ9 1-805-011-11 DIODE UDZ9.1B
VZ10 1-805-011-11 DIODE UDZ9.1B
< IC >
AIC2 1-805-024-11 IC DA CONVERTER
AIC4 1-805-028-11 IC 4560 (OP AMP)
AIC5 1-805-028-11 IC 4560 (OP AMP)
DOIC1 1-805-039-11 IC M74HCU04
PIC1 1-805-030-11 IC 1563 (V REGULATOR)
PIC2 9-885-037-02 IC POSI.FIXED
PIC3 1-805-031-11 IC 3RD13 (V REGULATOR)
RIC1 9-885-037-19 IC S5L1463A01 (ASIC)
SIC1 9-885-037-18 IC S5L1455X01 (ASIC)
SIC2 9-885-036-98 IC 41LV16256 (DRAM)
SIC3 9-885-036-97 IC FAN8728 (MOTOR DRIVER)
VIC1 9-885-037-03 IC LA73054 (VIDEO)
ZIC1 9-885-037-04 IC ZR36748 (DECODER)
ZIC2 9-885-036-99 IC IS42S16400A-7T (DRAM)
ZIC3 9-885-037-00 IC FLASH MEMORY
ZIC7 1-805-027-11 IC 24C021 (EEPROM)
ZIC8 1-805-022-11 IC 74VHCT125A (CMOS LOGIC)
< COIL >
AL1 1-400-316-11 INDUCTOR 0uH
AL2 1-400-316-11 INDUCTOR 0uH
AL3 1-400-316-11 INDUCTOR 0uH
AL4 1-400-316-11 INDUCTOR 0uH
< TRANSISTOR >
AQ1 1-805-017-11 TRANSISTOR 200MW
AQ2 1-805-018-11 TRANSISTOR KSR2103
AQ3 1-805-016-11 TRANSISTOR KSC1623-L
AQ4 1-805-017-11 TRANSISTOR 200MW
AQ5 1-805-018-11 TRANSISTOR KSR2103
AQ6 1-805-016-11 TRANSISTOR KSC1623-L
AQ7 1-805-017-11 TRANSISTOR 200MW
AQ8 1-805-018-11 TRANSISTOR KSR2103
AQ9 1-805-015-11 TRANSISTOR KSA812
DQ1 1-805-016-11 TRANSISTOR KSC1623-L
DQ2 1-805-016-11 TRANSISTOR KSC1623-L
DQ3 1-805-016-11 TRANSISTOR KSC1623-L
RQ1 1-805-014-11 TRANSISTOR KSA1182-Y
RQ2 1-805-014-11 TRANSISTOR KSA1182-Y
< VIBRATOR >
SY1 1-795-749-11 CRYSTAL UNIT (33.8688MHz)
ZY1 1-795-750-11 CRYSTAL UNIT (27MHz)
VCR MAIN BOARD
***************
FC1S01 1-576-527-11 FUSE CLIP
FC1S02 1-576-527-11 FUSE CLIP
LD601A 3-067-777-01 HOLDER-LED
S601A 3-075-066-01 HOLDER-SENSOR
VCR MAIN

8-7
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
VCR MAIN
S602A 3-075-066-01 HOLDER-SENSOR
TM401B 9-885-037-17 ASSY CONNECTOR BOARD
< CAPACITOR >
C1S02 1-165-559-11 CONDENSER 100PF
C1S03 1-165-559-11 CONDENSER 100PF
C1S04 1-165-573-11 CONDENSER FILM 0.1uF
C1S05 1-165-573-11 CONDENSER FILM 0.1uF
C1S06 1-165-557-11 CONDENSER 2200PF
< DIODE >
D301 1-804-416-11 DIODE MTZJ5.1B
D503 1-804-407-11 DIODE IN4148
D504 1-804-407-11 DIODE IN4148
D505 1-804-407-11 DIODE IN4148
D506 1-804-407-11 DIODE IN4148
D507 1-804-407-11 DIODE IN4148
D601 1-804-407-11 DIODE IN4148
D603 1-804-409-11 DIODE IN4002
D604 1-804-409-11 DIODE IN4002
D605 1-804-407-11 DIODE IN4148
D606 1-804-409-11 DIODE IN4002
D701 1-804-407-11 DIODE IN4148
D702 1-804-407-11 DIODE IN4148
D703 1-804-407-11 DIODE IN4148
D704 1-804-407-11 DIODE IN4148
D802 1-804-416-11 DIODE MTZJ5.1B
D803 1-804-407-11 DIODE IN4148
D1S01 1-804-413-11 DIODE IT5
D1S02 1-804-413-11 DIODE IT5
D1S03 1-804-413-11 DIODE IT5
D1S04 1-804-413-11 DIODE IT5
D1S05 1-804-408-11 DIODE UF4007
D1S06 1-804-407-11 DIODE IN4148
D1S07 1-804-412-11 DIODE FIT4
D1P101 1-804-409-11 DIODE IN4002
D1P102 1-804-409-11 DIODE IN4002
D1P103 1-804-407-11 DIODE IN4148
D1P105 1-804-407-11 DIODE IN4148
D1P107 1-804-407-11 DIODE IN4148
D1P108 1-804-407-11 DIODE IN4148
D1SS05 1-805-041-11 DIODE SE55
D1SS07 1-805-041-11 DIODE SE55
D1SS08 1-805-041-11 DIODE SE55
D1SS09 1-804-412-11 DIODE FIT4
D1SS12 1-804-412-11 DIODE FIT4
D1SS13 1-804-411-11 DIODE UG2D
D1SS15 1-804-412-11 DIODE FIT4
ZD401 1-804-414-11 DIODE UZP33B
ZD1P02 1-804-418-11 DIODE MTZJ12B
ZD1P04 1-804-416-11 DIODE MTZJ5.1B
ZD1P05 1-804-418-11 DIODE MTZJ12B
ZD1P06 1-804-416-11 DIODE MTZJ5.1B
ZD1S01 1-805-265-11 DIODE MTZJ4.3B
ZD1S02 9-885-036-94 DIODE MTZJ20B
< DISPLAY >
DT701 9-885-037-10 LED DISPLAY LTG-0262M (LITE-ON)
< FUSE >
0F1S01 1-576-525-11 FUSE (1.6A/250V)
< IC >
IC301 1-805-296-11 IC LA71207 (VIDEO)
IC501 1-804-434-11 IC AN3663FBP
IC601 9-885-037-11 IC MN101D06F-XG1 (MICOM)
IC603 1-805-042-11 IC 524C80D41 (EEPROM)
IC6B1 1-804-444-11 IC KA7533
IC701 1-804-706-11 IC LED DRIVER
IC801 9-885-036-96 IC BU4053BCFV (CMOS LOGIC)
IC1S01 9-885-037-01 IC PWM CONTROLLER
0IC1S02 1-804-784-11 IC PHOTO COUPLER
IC1SS2 1-804-445-11 IC KA4318
< JACK >
JK801 1-815-699-11 JACK RCA 6P (LINE IN 1/LINE OUT)
< COIL >
0L1S02 1-424-831-11 LINE FILTER 20mH
< LED >
LD601 1-804-438-11 LED-IR (T/S LED)
< TRANSFORMER >
0PT1S01 9-885-037-12 TRANS SWITCHING EER3530
< PHOTO INTERRUPTER >
PT601 1-804-770-11 PHOTO INTERRUPTER (S REEL)
PT602 1-804-770-11 PHOTO INTERRUPTER (T REEL)
< TRANSISTOR >
Q302 1-804-420-11 TRANSISTOR KSA733
Q303 1-804-421-11 TRANSISTOR KSC945
Q304 1-804-420-11 TRANSISTOR KSA733
Q305 1-804-422-11 TRANSISTOR KTC3023
Q306 1-804-420-11 TRANSISTOR KSA733
Q307 1-804-422-11 TRANSISTOR KTC3023
Q308 1-804-422-11 TRANSISTOR KTC3023
Q601 1-804-428-11 TRANSISTOR KSR1004
Q701 1-804-421-11 TRANSISTOR KSC945
Q801 1-804-421-11 TRANSISTOR KSC945
Q802 1-804-428-11 TRANSISTOR KSR1004
Q803 1-804-428-11 TRANSISTOR KSR1004
Q804 1-804-429-11 TRANSISTOR KSR2001
Q805 1-804-421-11 TRANSISTOR KSC945
Note :
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.

8-8E
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
VCR MAIN
Q806 1-804-421-11 TRANSISTOR KSC945
Q807 1-804-421-11 TRANSISTOR KSC945
Q808 1-804-421-11 TRANSISTOR KSC945
Q1S01 9-885-036-95 FET SILICON
Q1P101 1-804-424-11 TRANSISTOR KSC2328AY
Q1P102 1-804-429-11 TRANSISTOR KSR2001
Q1P103 1-804-421-11 TRANSISTOR KSC945
Q1P105 1-804-424-11 TRANSISTOR KSC2328AY
Q1P106 1-804-424-11 TRANSISTOR KSC2328AY
Q1P107 1-804-424-11 TRANSISTOR KSC2328AY
Q1P108 1-804-429-11 TRANSISTOR KSR2001
Q1P109 1-804-421-11 TRANSISTOR KSC945
Q1P110 1-804-424-11 TRANSISTOR KSC2328AY
Q1P111 1-804-424-11 TRANSISTOR KSC2328AY
< REMOCON MODULE >
RM701 1-477-308-11 REMOCON MOD (TSOP2238WE1)
< PHOTO TRANSISTOR >
S601 1-804-439-11 PHOTO TRANSISTOR (END SENSOR)
S602 1-804-439-11 PHOTO TRANSISTOR (START SENSOR)
< SWITCH >
SW602 1-786-199-11 SWITCH REC (REC SWITCH)
SW603 1-786-198-11 SWITCH MODE (PROGRAM SWITCH)
< TUNER >
TM401 1-693-638-11 TUNER NTSC TMZH2002A
< VARISTOR >
0VA1S01 1-804-437-11 VARISTOR
< VIBRATOR >
XT301 1-795-333-11 VIBRATOR CRYSTAL (3.579545MHz)
XT601 1-795-996-11 CRYSTAL UNIT (14.318448MHz)
MISCELLANEOUS
***************
010 1-824-674-11 POWER CORD EP2 SPT-2
109 9-885-037-15 ASSY CLYNDER 6HD
118 1-763-836-11 LOADING ASSY, MOTOR
152 1-796-432-11 MOTOR CAPSTAN
202 9-885-037-20 MOTOR LOADING ASSY
0204 9-885-037-37 ASSY PICK UP
206 9-885-037-21 MOTOR-SPINDLE
210 9-885-037-22 MOTOR FEED ASSY
218 9-885-037-38 ASSY DVD DECK
ACCESSORIES & PACKING MATERIALS
********************************
3-078-598-01 BATTERY COVER (COMBO GRAY)
(for RMT-V501A)
3-083-945-11 MANUAL, INSTRUCTION (ENGLISH)
9-885-035-23 COMMANDER, STANDARD (RMT-V501A)
Note :
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.

— 12 —
Sony Corporation
HomeVideo Company
9-929-753-31 2003D0500-1
©2003. 4
Published by Customer Support Center
SLV-D300P