Sound Leisure venue User manual

QMS Document Venue Hub –Digital I/R Instructions Page 1of 7
Version: 3.0 16/08/2016
Venue Hub - Digital I/R Kit Instructions
Kit Contents:
1 X IR Receiver & Mount Plate
1 X Data Harness
1 X Remote Control with 2 X AA Batteries
IMPORTANT: Beforeinstalling the IR kit pleaseensure that your SLE 1026 board is running
software version v6.0or higher andthe amplifieris runningonsoftware versionv4.8or
higher. The IR kit will not work on older software
To check software version on the amplifier switch the machine on and look at the LCD
display. Itwill display the software version on boot up.
To check software version on the SLE 1026 board look for a white label near the EEPROM.
If you cannot see the version on any labels the SLE 1026 will require updating.
When installing the IR kit you must remove your RVC cables from the amplifier (RVC1&
RVC 2). If the RVC cables from the SLE 1026 are left connected the amp may ignore
commands from the IR remote.

QMS Document Venue Hub –Digital I/R Instructions Page 2of 7
Version: 3.0 16/08/2016
Fitting the IR kit
1. Openthe door and remove the metal bracket at the bottom of the door. It is held in
place by two screws.
2. Remove the black rectangular piece of vinyl from the door or the IR signal will not
pass through

QMS Document Venue Hub –Digital I/R Instructions Page 3of 7
Version: 3.0 16/08/2016
3. Attachthe metal bracket which holds the IR Receiver and hold it in place. Ribbon
cables on right hand side.
4. Attachthe metal bracket you removed first on top of the IR mounting plate as this
pushes against the door switch Put both screws backin to secure it all in place.

QMS Document Venue Hub –Digital I/R Instructions Page 4of 7
Version: 3.0 16/08/2016
5. Route the ribbon cable to the SLE1026 and Amplifier using the clips on the door
6. Connect the remaining 3 wire connector (Blue, Green and Yellow) to the 4-pin
header on the SLE 1026 (Con 13) as below

QMS Document Venue Hub –Digital I/R Instructions Page 5of 7
Version: 3.0 16/08/2016
7. Plug the other connector into the Comms. port on the amplifier
8. Remove the 2 RVC connectors from the amplifier

QMS Document Venue Hub –Digital I/R Instructions Page 6of 7
Version: 3.0 16/08/2016
9. Now reset the jukebox and let it fully boot back up.
Close the door on the machine andtest that when you press the buttons on the remote control
the redLED on the 1120 board flashes andthe remote control canadjust the volume on all
four channels, mute and eject tracks. The board has been proven to work at a distance of 3.2
Metres.
Troubleshooting:
Remote Not Working –
Press a button on the remote and check that the red LED flashes. If it doesn’t check the
polarity of the batteries, if the batteries are in the correct wayreplace them. If the remote
doesn’t work with new batteries please call for support.
Receiver NotFlashing –
When a button is pressed on the remote the receiver should flash. If it doesn’t check the
wiring to the receiver,checkthe mounting position andmake sure that you are within range
(Approx 3 Metres). The receiver needs to be in the line of sight of the remote control. It may
not detect a signal if you are stood side on.
Receiver Flashes But Does Not AdjustVolume Etc. –
If the red LED flashes when a button is pressed, but the volume does not adjust or a song does
not reject, checkthe wiring to the receiver, Amplifier andSLE 1026 board.
Make sure the software onthe SLE 1026 and Amplifier is correct (See page 1 for more
details). Make sure that the RVC cables to the Amplifier are removed. You should then be
able to adjust volume using IR remote. Usually it is old software on the SLE 1026 or Amp.

QMS Document Venue Hub –Digital I/R Instructions Page 7of 7
Version: 3.0 16/08/2016
FurtherIssues -
Ensure that the jukebox is playing anaudio track,if the amp displays no juke / no auxinput
there is no audio signal coming into the amp. Also checkthat the audio and speaker cables are
wired correctly.
If these steps are correct reboot the machine and let the machine boot back up with the RVCs
turned off. Onreboot the amp should detect the IR board.
For further technical assistance please contact Sound Leisure Digitech department
0845 230 1775
[e-mail]