SoundCraft 328xd User manual

18
21
24
27
30
35
40
0
2
4
6
8
10
12
14
16
RIGHT
STE-2STE-1
SELECT
MUTE
SOLO
MIX
dBFS
0dBFS = 18dBu
STEREO INPUTS
GROUP LINK
CHANNEL /
XDX D
EXIT
PARAMETER
FUNCTION
OUT
THRU
MIDI
IN OUT IN
IN
OUT
S/PDIF
OUT IN
AES/EBU
WORD
CLOCK CLOCK
WORD/SUPER
M-AUDIO LAGOON
328
XD

Soundcraft 328XD and M-Audio Lagoon
1
11
1
328XD AND
328XD AND328XD AND
328XD AND
M-AUDIO LAGOON
M-AUDIO LAGOONM-AUDIO LAGOON
M-AUDIO LAGOON
Connecting the system 2
328XD Configuration 3
Lagoon Configuration 5
Using the Lagoon with the 328XD 9
Additional Information 10

Soundcraft 328XD and M-Audio Lagoon
2
22
2
CONNECTING THE SYSTEM
Audio Connections
Audio connections should be made as shown in the diagram below. ADAT optical cables must be
connected both from ADAT Out port of the Lagoon card to the 328XD ADAT In 17-24 and vice versa.
The optical plugs should remain in the 328XD ADAT port 25-32 input and output.
In this configuration, the ADAT connections allow digital transfer of either direct outputs from the 328XD’s
input channels 1-8 to the Lagoon card, or the 328XD’s 8 Group outputs.
Other Connections
You may also wish to connect the 328XD to the Lagoon card with MIDI cables to allow MIDI automation /
System Exclusive dumps from the 328XD to be recorded and played back from your PC.
If you wish to connect the 328XD MIDI I/O to the Lagoon, the following connections must be made:

Soundcraft 328XD and M-Audio Lagoon
3
33
3
328XD CONFIGURATION
The Lagoon card and the 328XD (plusany otherdevices in thestudio setup) must have their internal
clocks synchronized toallow correct transmission and reception of digital information throughout the
system. This isachieved by configuring one of thedevices as awordclock host,andconfiguring all
other devices in thestudio setup to sync tothis wordclock, hence synchronizing all clocks in the
studio setup.
In this case, the328XD will be setto wordclockhost,and the Lagoon will be setto sync to the
328XD, via theLagoon ADAT input–see Lagoon Configuration . Any other devices interfacing
digitally with the328XDwithin thestudio setupwill also be configured tosync to the328XD’s
wordclock.
NOTE: Wordclock information is embedded into the 328XD ADAT output data stream, allowing the
Lagoon tosync to the 328XD’s ADAT output
To configure the328XD as thewordclock host,enter the 328’s Main Menu page by pressing the
<MENU> button to the right hand side of the LCD display. Using thePARAM encoder beneath the
display, scroll up or down until the ‘Clock Source Sel’ menu is highlighted, and press <ENTER>. Here,
either ‘Internal: 44.1kHz’ or‘Internal: 48kHz’ clock must be selected for the 328XD to function as
wordclock host.With thePARAM encoder set this to thesample rate you wish to work at, press
<ENTER> to confirm the sample rate setting and <MENU> to return to the menu pages.
Tape Port Setup
To ensure that the 328XD Tape Port 17-24 is configured to ‘ADAT’ to work with the Lagoon, enter the
328XD Menu pages by pressing the <MENU> button to the right hand side of the LCD display. Using
the PARAM encoder beneath the display, scroll up or down until the ‘Tape Port Select’ menu is
highlighted and press <ENTER>.
Now press the Up cursor key until the ‘<Tape Ch17-24 >’ menu page is displayed. Using the PARAM
encoder set the ‘Bank Source’ to ‘ADAT’:
The Lagoon is capable of 24 bit recording, and so for optimum results, 24 bit wordlength can be selected
here. If your audio sequencer supports only 16 or 20 bit resolution, set the wordlength appropriately–
check your sequencer manual for more information.
Set the desired wordlength on the 328XD with the PARAM encoder.

Soundcraft 328XD and M-Audio Lagoon
4
44
4
NOTE:
In a setup with the Lagoon connected to 328XD ADAT input and output 17-24, Tape Port 25-
32 should be left set to TDIF. Alternatively, the Lagoon can be connected to 328XD ADAT input
and output 25-32, and Tape Port 17-24 set to TDIF. In this case, the above settings should be
made to Tape Port 25-32.

Soundcraft 328XD and M-Audio Lagoon
5
55
5
LAGOON CONFIGURATION
Input Setup
To set up the Lagoon for connection to the 328XD, first click on the Lagoon Tools icon on the Windows
taskbar:
The Lagoon Tools application should open. Click on the ‘General’ tab. The following window should open.
Set both the input and output to be ADAT format:

Soundcraft 328XD and M-Audio Lagoon
6
66
6
The Lagoon clock source must then be set so that its internal clock is synchronised totheincoming
ADAT wordclock output from the328XD. Set ‘Clock Source’ to ‘Optical In’:
The Lagoon card will automatically detect the sample rate at the ADAT input, and so to alter the sample
rate, the 328XD internal clock frequency should be adjusted - see page 3.
NOTE:
The ‘T2S’ filter should be left unchecked as the 328XD is fitted with Toshiba optical receivers
and transmitters.

Soundcraft 328XD and M-Audio Lagoon
7
77
7
MIDI Setup
Click on the MIDI tab within the Lagoon Tools application, and enable the Lagoon MIDI input and output
ports:
The Lagoon MIDI input and output ports should be selected within your chosen MIDI sequencer to enable
record and playback of 328XD automation data.

Soundcraft 328XD and M-Audio Lagoon
8
88
8
Clear all Errors
Until the Lagoon is set to synchronize to the 328XD host wordclock (page 6), the clocks will run out of
sync. Spurious clicks and pops or distorted audio may well be heard asa result. While configuring the
system then, it is likely that the Lagoon will have registered wordclock synchronization errors. To reset the
Lagoon, click on theLagoon Tools ‘Status’ tab, and then the‘Clear all errors’ button:
If any of the error LEDs light or remain lit, check that the ADAT connections and 328XD and Lagoon Tools
settings are correct.
NOTE:
Once the Lagoon registers no errors, the Lagoon and 328XD clocks are synchronized. The
328XD mix fader, control room and headphone output levels may be raised.

Soundcraft 328XD and M-Audio Lagoon
9
99
9
USING THE LAGOON WITH THE 328XD
Accessing the Lagoon ADAT I/O from the 328XD
The Lagoon will commonly be used with a software audio sequencer / hard disk recorder to allow the
simultaneous playback and recording of 8 individual tracks of audio, via the ADAT I/O. Here, the software
application must be configured to access the Lagoon ADAT I/O using the relevant Windows device drivers
that came with the card.
When playing back audio tracks from the software application, tracks 1-8 will be accessible from
channels 17-24 respectively in the BANK SELECT 17-32 on the 328XD.
See the 328XD User Guide for full instructions on how to send a channel or group to tape / audio
sequencer. By default the 328XD is configured to send analogue input channels 1-8 directly to tape
outputs 1-8 post-fade.
NOTE:
Ensure that the relevant device drivers are fully installed for the software application to
correctly access the Lagoon ADAT I/O. Consult the Lagoon manual for more information.

Soundcraft 328XD and M-Audio Lagoon
10
1010
10
ADDITIONAL INFORMATION
S/PDIF
The 328XD Auxiliary Optical Out port can be set to transmit an optical format S/PDIF signal. Enter the
328XD Tape Port Select menu and press the Down cursor key until the ‘Aux Optical Out’ menu is active.
Using the PARAM encoder set the format to ‘S/PDIF’. Press <MENU> to return to the menu pages.
The configuration of this output is made in the ‘SPDIF O/P Setup’ menu. The signals is duplicated at the
coaxial S/PDIF output.
NOTE:
Settings of ‘AUX/MIX’ and ‘GROUP’ will configure the console to transmit an ADAT format output
from the Auxiliary Optical Out port.
SOUNDCRAFT
HARMAN INTERNATIONAL INDUSTRIES LTD
CRANBORNE HOUSE
CRANBORNE ROAD
POTTERS BAR
HERTS EN6 3JN UK
TEL: [phone]
FAX: [phone]
EMAIL: [e-mail]
SOUNDCRAFT USA
1449 DONELSON PIKE
NASHVILLE TN 37217 USA
TEL: [phone]
FAX: [phone]
EMAIL: [e-mail]
www.soundcraft.com