SoundCraft 328xd User manual

18
21
24
27
30
35
40
0
2
4
6
8
10
12
14
16
RIGHT
STE-2STE-1
SELECT
MUTE
SOLO
MIX
dBFS
0dBFS = 18dBu
STEREO INPUTS
GROUP LINK
CHANNEL /
XDX D
EXIT
PARAMETER
FUNCTION
OUT
THRU
MIDI
IN OUT IN
IN
OUT
S/PDIF
OUT IN
AES/EBU
WORD
CLOCK CLOCK
WORD/SUPER
MOTU 2408 MKII
328
XD

Soundcraft 328XD and MOTU 2408 mkII
1
11
1
328XD AND
328XD AND328XD AND
328XD AND
MOTU 2408 MKII
MOTU 2408 MKIIMOTU 2408 MKII
MOTU 2408 MKII
Connecting the system 2
328XD Configuration 3
MOTU 2408 mkII Configuration 5

Soundcraft 328XD and MOTU 2408 mkII
2
22
2
CONNECTING THE SYSTEM
Audio Connections – ADAT Operation
Connect audio connections as shown in the diagram below. ADAT Optical cables must be connected
from the ADAT Out ports of the Mark of the Unicorn 2408 mkII hardware to the ADAT In ports of the
328XD and vice versa.
The ADAT connections allow digital transfer of either direct output for input channels 1-16 to the Mark
of the Unicorn 2408 mkII hardware, or the 328XD’s 8 Group outputs.
The S/PDIF connections allow digital transfer of stereo signals, such as the mix output of the 328XD
into the 2408 mkII for recording to hard disk.

Soundcraft 328XD and MOTU 2408 mkII
3
33
3
328XD CONFIGURATION
Wordclock
To configure the 328XD as the wordclock master, enter the 328XD Menu pages by pressing the <MENU>
button on the right hand side of the LCD display. Using the PARAM encoder beneath the display, scroll up or
down until the ‘Clock Source Sel’ menu is highlighted, and press <ENTER>. Here, either the internal
44.1kHz clock or the internal 48kHz clock must be selected, depending on the sampling rate at which work
is to be done. Press <ENTER> to set the sample rate and <MENU> to return to the menu pages.
Tape Ports
To ensure that the 328XD Tape Ports are set to ADAT to work with the MOTU 2408 mkII, enter the
328XD Menu pages by pressing the <MENU> button on the right hand side of the LCD display. Using the
PARAM encoder beneath the display, scroll up or down until the ‘Tape Port Select’ menu is highlighted.
Press <ENTER> and keep pressing the Up cursor arrow until the ‘<Tape Ch17-24 >’ menu page is
displayed. Using the encoder set the Bank Source to ADAT.
Press the Down cursor arrow once, to set the wordlength. The MOTU 2408 mkII is capable of 24-bit
recording, and so for optimum results, 24-bit wordlength can be selected here. If your audio sequencer
software does not allow 24-bit recording, 20-bit or 16-bit should be selected. The sequencer manuals
should be consulted for further information.
Set the desired wordlength on the 328XD with the PARAM encoder.
Press the <MENU> button to return to the main menu.

Soundcraft 328XD and MOTU 2408 mkII
4
44
4
S/PDIF Input
The 328XD S/PDIF input can be routed to any one of the following inputs:
Stereo Input 1, Stereo Input 2, FX - 1, FX - 2, 2 Track Tape Return,
provided that the AES/EBU input or oscillator has not already been assigned to that input.
Commonly the 2408 S/PDIF output would be routed to Stereo Input 2, or the 2 Track Tape Return input.
NOTE:
Assigning a digital source to an input will override any analogue signal present on that input.
Press <MENU> to enter the menu pages, scroll through the pages until the ‘SPDIF I/P Setup’ is
highlighted and press <ENTER>. Using the PARAM encoder, select the destination for the S/PDIF input,
and press <ENTER> to confirm the setting. Press <MENU> to return to the menu pages.
NOTE:
If the S/PDIF input is not required, NOWHERE should be selected in the menu.

Soundcraft 328XD and MOTU 2408 mkII
5
55
5
MOTU 2408 MKII CONFIGURATION
Wordclock
The Mark of the Unicorn 2408 mkII must now be set up to receive the wordclock transmitted by the 328XD.
Open the PCI-324 Console window, by double clicking the correct icon and select "2408 mkII :Bank A
Optical" from the ‘Clock Source’ options.
NOTE: If TDIF isused for audio data, then the Mark of the Unicorn 2408 mkII must operate as a
master to send wordclock to the Digital 328. A Wordclock cable must be fitted from the
WORDCLOCK OUT of the MOTU2408 mkII to the WORDCLOCK IN of the Digital 328. The
328XD must then be set to client fromBNC wordclock input in the"Clock Source Select
Menu. All 16 audio channels may be exchanged using two TDIF cables connecting the
328XD and the MOTU 2408 mkII.

Soundcraft 328XD and MOTU 2408 mkII
6
66
6
Audio Data
The Mark of the Unicorn 2408 mkII must now be set up to transmit and receive audio data to and from
the 328XD.
Open the PCI-324 control panel and select ADAT or TDIF, depending on which is being used for each of
the required ports.
Remember you can link two 328XDs together, and the MOTU 2408 mkII system can be expanded to 3 x
2408 mkII's. With these options you can actually run 32 digital channels and 32 analogue channels from
your chosen sequencer.
Please refer to the Mark of the Unicorn 2408 mkII documentation for other system settings, when working
with sequencer packages. The synchronisation options described within this document are normally
available from within an audio system settings page.
SOUNDCRAFT
HARMAN INTERNATIONAL INDUSTRIES LTD
CRANBORNE HOUSE
CRANBORNE ROAD
POTTERS BAR
HERTS EN6 3JN UK
TEL: [phone]
FAX: [phone]
EMAIL: [e-mail]
SOUNDCRAFT USA
1449 DONELSON PIKE
NASHVILLE TN 37217 USA
TEL: [phone]
FAX: [phone]
EMAIL: [e-mail]
www.soundcraft.com