SoundMax SM-CCR3064F User manual

SM-CCR3064F4 x 40W
SM-CCR3064F
RES
CLK/AMS/

This device is intended for installation in a vehicle with onboard voltage 12 V. Designed to receive radio FM
and playing MP3 from media USB and microSD (TF).

Important safeguards
•Read carefully through this manual to familiarize yourself with this high-quality sound system.
•The beginning of operation is the moment of the unit installation. Before use the device in winter it is
recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.
•Use the unit with the temperature that goes beyond the operation temperature greatly decreases the
operation resource of the screen and other components of device and can result an outage.
•Disconnect the vehicle's negative battery terminal while mounting and connecting the unit.
•When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher
amperage rating may cause serious damage to the unit.
•Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions, or
create safety hazards such as electrical shock.
•Do not use the unit in places where it can be exposed to water, moisture and dust.
•Do not open covers and do not repair yourself. Consult the dealer or an experienced technician for help.
•Make sure you disconnect the power supply and aerial if you will not be using the system for a long period
or during a thunderstorm.
•Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an
unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a
qualified technician check the system.
•The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please
confirm it before installation.
•Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may
overload or burn out the power amplifier.
3

Accessories
4
1. Reсeiver
2. 12 - pin connector cable
3. Mounting parts:
Release key
Mounting сollar
4. Instruction manual
1 рс
2 pсs
1 рс
1 рс
1 рс

Installation/Connection
General notes
• Choose the mounting location where the unit will not interfere with the normal driving function
of the driver.
• Before finally installing the unit, connect the wiring and make sure that the unit works properly.
• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of
the vehicle.
• Install the unit where it does not get in the driver's way and cannot injure the passenger if
there is a sudden stop, like an emergency stop.
• Avoid installing the unit where it would be subject to high temperature, such as from direct
sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive
vibration.
•
•
•
•
Install the sleeve into the dashboard; ensure it is installed
with the correct side and there are no obstacles (wires,
dashboard elements, etc) for the unit installation.
After installing the sleeve into the dashboard, bend tabs fitting
to the size of the dashboard to fix the sleeve in place.
Make the necessary wire connections. Ensure the connections
are correct.
Install the unit into the sleeve until the side locks are fixed .
1. Dash board
2. Sleeve tab to bend
5

, for this you need to break the plastic plugs.

The negative electrode of the speaker mustn't be grounded, or else it may burn the player!
Attention, the 12-pin connector cable must be carefully matched with description on RL, connection
of any wrong cables (WHITE-BLACK/ GREEN-BLACK/ PURPLE-BLACK/ GRAY-BLACK) with the Black
cable (Ground) can be the reason of a malfunction of the built-in amplifier.
1-FL+
5-B+
9-RR+ 10-RR- 11-ANT 12-ACC
2-FL-
6-GND
3-RL+
7-FR+
4-RL-
8-FR-
Antenna Terminal
1
2
3
4
5
6
7
8
9
10
11
12

124
35
6
7
9 8
RES
CLK/AMS/
1011
SM-CCR3064F4 x 40W
1. CLK/AMS/ button
2. VOL+ button
3. button
4. /MOD button
5. LCD display
6. Aux-in port
7. Micro SD card slot
8. USB port
9. Reset button (hole)
10. button
11. VOL- button

Adjust the volume by pressing the VOL+ and VOL- buttons.
Press and hold this button again to turn the unit off.
CLK button
button until the clock starts to blink, then press the VOL-/VOL+ buttons to set the current hour.
Then press the CLK button again and use the VOL-/VOL+ buttons to set the current minutes. After 5
seconds the system will confirm the time settings.