Soundoff Signal 400 Series User manual

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 1
ETCPRSP01 -8 BUTTON CONTROLLER W/ SLIDE SWITCH - KIT
Please see page 3 for
Technical Specications
!
WARNING
Sirens produce loud sounds that
may damage hearing:
- Roll up windows.
- Wear hearing protection.
- Use only for emergency response.
- Avoid exposure to siren sound
outside of vehicle.
8 Button Control Panel
Amplier
Microphone
Introduction
The ETCPRSP01 is Remote Mounted
Controller and amplier with lighting control.
It can drive a variety of programmable
powered control lines capable of up to nine
10A and three 20A circuits.
Notice
Controllers provide an essential function of
an effective visual warning system.
However, this controller is only a short range
secondary device. The use of this controller
does not insure that all drivers can or will
abide by or react to an emergency warning
signal, especially at high rates of speeds or
long distances. The operator of the vehicle
must never take the right of way for granted
and it is the operator’s responsibility to
proceed safely.
The effectiveness of this system is highly
dependant on the correct mounting and
wiring. The installer must read and follow
the manufacturer’s installation instructions
and warnings in the manual. The vehicle
operator should verify the system is securely
fastened to the vehicle and properly
functioning.
This system is intended for use by
authorized personnel only. It is the user’s
responsibility to ensure they understand and
operate the emergency warning devices in
compliance with all applicable city, state,
and federal laws and regulations. SoundOff
Signal assumes no liability for any loss
resulting from the use of this system.
IMPORTANT NOTICE TO INSTALLER:
Make sure to read and understand all
instructions and warnings before proceeding
with the installation of this product. Ensure
the manual and all warning cards are
delivered to the end user of this equipment.
PSRN4ANRI - 100W
PCPRSP01
Package Contents:
1 ea. Amplier Box
1 ea. Microphone Bracket w/ Mounting
Hardware
5 ea. Amplier Wire Harnesses with
Connectors (1-4 pin, 1-12 pin, 1-5
pin 1-14 pin and 1-8 pin)
2 ea. Instruction Manual
1 ea. Operators Warning Card to remain
in vehicle for operator review
1 ea. Sound Pressure Warning Label that
is to be attached in vehicle and in
plain site of operator and occupants
of the vehicle
1 ea. Mounting Bracket with Hardware
1 ea. Label Card for Aux. Switches
1 ea. Remote control panel
D1_Remote Console Panel Assy
MATERIAL:
THIRD ANGLE
PROJECTION
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL.
ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
®
REVISION:
DESCRIPTION:
SHEET
1 OF 1
DRAWING
SIZE:
DO NOT SCALE
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
PRIMARY DIMS: INCH
DUAL DIMS: [mm]
A
DRAWING NO:
A A
B B
C C
D D
E E
5
5
4
4
3
3
2
2
1
1
GD&T TO FOLLOW
ASME Y14.5M-2009
CAD DIMENSIONS ARE BASIC
UNLESS OTHERWISE SPECIFIED

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 2
1 PSRN4ANR1 Replacement Amp/Relay Assembly-100 Watt
2 PSRN4ANR2 Replacement Amp/Relay Assembly-200 Watt
3 PSRN4HDK2 Fuse Kit
4 PSRN4HDK1 Harness Kit
5 PSRN4MTBK1 Mounting Bracket
6 PSRNLEG1 Auxiliary Button Legends-Remote
7 PSRNMC1 Microphone
8 PSRNSWK1 Slide Switch Kit
9 PSRNMMC1 Microphone Mounting Clip
10 PCPRSP01 8 Button Control Panel
11 PSRNBLBK1 Bail Bracket Kit
Replacement Parts & Accessories:
8 BUTTON CONTROLLER W/ SLIDE SWITCH - KIT
ETCPRSP01
4
6
5
13 2
10
7
11
REPLACEMENT PARTS & ACCESSORIES
9
8
D1_Remote Console Panel Assy
MATERIAL:
THIRD ANGLE
PROJECTION
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL.
ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
®
REVISION:
DESCRIPTION:
SHEET
1 OF 1
DRAWING
SIZE:
DO NOT SCALE
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
PRIMARY DIMS: INCH
DUAL DIMS: [mm]
A
DRAWING NO:
A A
B B
C C
D D
E E
5
5
4
4
3
3
2
2
1
1
GD&T TO FOLLOW
ASME Y14.5M-2009
CAD DIMENSIONS ARE BASIC
UNLESS OTHERWISE SPECIFIED

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 3
-Microphone Bracket Installation-
A metal clip is provided for mounting the microphone. Choose a
location convenient to the operator and away from any air bag
deployment areas. Using the mounting clip as a template, mark the
two holes to be drilled. Using a 1/8” drill bit, drill the two mounting
holes. Install the two #6 screws provided with the bracket.
WIRING:
WARNING! All customer supplied wires connecting to the
positive terminal of the battery must be sized to supply at least
125% of the maximum operating current and FUSED at the
battery to carry that load.
Ensure the amplier / relay unit is mounted in dry, protected
environment.
TECHNICAL SPECIFICATIONS
Overall Dimensions:
Control Panel:
Amplier/Relay:
3.51” W x 6.89”H x 1.17”D
2.62”H x 7.00”W x 6.51”D
Input Voltage: 10 - 16Vdc (negative ground)
Boxed Weight: 8 lbs.
Operating Temperature: -40°C to +50°C
Diagnostic LEDs: Speaker shorted/open, internal fuses open,
communications faults
Amplier
Input Current 7 Amps @ 13.4 VDC (100W Speaker)
Standby Current:
Ignition ON:
Ignition OFF:
500mA
<10mA
Output Power : ETSA481: 1x100W RMS Max (11 Ohm speaker)
Audio Frequency: 500-3 kHz
Siren Frequency:675Hz - 1633Hz
High Voltage Protection: Limits to <18V*
Low Voltage Shutdown: Voltage<9.0V will cause siren output to cease
and will resume when system voltage is >9.5V
Speaker Protection: Shorted, Open: Stop output signal, preserve Amp
Light Control
AUX button relays: 9 total 10A max each circuit
Total current not to exceed 50A for CN8 pin 5
2 of the 9 available for external Arrow control
2 of the 9 have their source voltage switchable
from internal to external via fuse location, see
pg 5
Slide Switch Relays: 3 total 20A max each circuit,
Total current not to exceed 50A for CN8 pin 4
WARNING
!
Do not install this product or route its wires in
the air bag deployment area.
Doing so may cause damage to or reduce
effectiveness of the air bag, or create projectile
that could cause serious injury or death.
To determine air bag deployment area refer to
vehicle manufacturer's manual.
MOUNTING
-Amplier Installation-
Before drilling holes, check for clearance to prevent
damage. Check both sides of the mounting surface
before drilling and the be aware of any vehicle
components or other vital parts that may be damaged
during drilling.
Install grommets in any wire passage holes.
1. Slide ¼” hex head bolts into amplier t-slots.
2. Place mounting brackets over bolts.
3. Thread ¼” lock nuts onto bolts and tighten down.
4. Use mounting bracket holes to secure amplier
5. Install amplier with clearance from other objects
for improved ventilation.
1
2
4
400 SERIES AMPLIFIER BOX
PSRN4ANR1

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 4
Auxiliary Input: (Violet Wire)
The input is an optional input which will remotely activate the
unit when the auxiliary input wire is connected to ground. If this
feature is needed, connect the auxiliary input wire to a switch
which provides a ground connection when activated. *Park kill
disables any active auxiliary tone. The auxiliary tone can be
reactivated when Park Kill is activated by toggling the Auxiliary
Input.
Radio Rebroadcast Input: (Blue Wires)
The 2 – 18ga blue wires on the 12 pin Molex connector are
used to connect your two-way radio’s external speaker through
the amplier and broadcast through the warning speaker and
is optional. Radio Rebroadcast will not work with remotely
amplied speakers due to the signal amplitude being too
low. Locate the 2 wires that connect the external speaker
to the two-way radio. T-tap one blue wire into the one of the
external speaker wires. T-tap the other blue wire into the other
external speaker wire. If the blue wires need to be extended,
use a minimum of 20ga. Wire. The Radio Rebroadcast volume
must be adjusted prior to placing vehicle into service. Set the
volume of the two-way radio to the normal operating level. Press
the Radio Rebroadcast push-button on the siren control panel.
With a small screwdriver, adjust the radio rebroadcast volume
potentiometer located on the back of the amplier to obtain the
proper volume out the speaker. Turn potentiometer clockwise to
increase volume and counter-clockwise to decrease volume.
Speaker Output: (Orange + Orange/Black Wires), (Green +
Green/Black wires) Route the Orange and Orange/Black wires
from the 4 position connector to the speaker. Use a minimum of
18ga. wire to extend the wires as needed. Connect the Orange
wire to the primary Speaker High wire. Connect the Orange/
Black wire to the primary Speaker Low wire.
Backlight Input: (Gray Wire)
The input will turn on the backlighting of the control panel
whenever +V is applied to the backlight input wire.
Route the amplier backlight input wire to the vehicle’s marker
light wiring using a minimum of 22ga. Wire to extend as needed.
T-tap the backlight input wire into the vehicle’s marker light +V
wire.
Park Kill Input: (Yellow Wire)
The input will silence the tones when the input wire
is activated. The input is typically connected to the
transmission neutral safety switch. If this feature
is required, the installer needs to determine if the
signal wire from the neutral safety switch is switch-
ing the +V or ground side of the circuit. Refer to the
programming instructions on how to set the park kill
polarity on the siren. Extend the park kill input wire
from the amplier to the neutral safety switch using
a minimum 22ga. Wire. Park kill Vin Low is < 5Vdc.
Ignition Input: (Orange/Black Wire)
The input is required to enable this system. Locate
the wire on the vehicle which provides +V when
the ignition switch is turned ON. Extend the ignition
input wire as needed using a minimum of 22ga.
Wire and tap into the vehicle ignition wire.
Wire capacity requirements for siren
amplier (incoming power)-each supply and
ground wire.
0-10 Feet: 14 AWG
10-20 Feet: 12 AWG
20-30 Feet: 10 AWG
30+ Feet: Consult Factory to determine
requirements
AUDIO WIRING
400 SERIES AMPLIFIER BOX
PSRN4ANR1
RADIO
REBROADCAST
NEUTRAL SAFETY SWITCH
IGNITION
3 amp
Fuse
YELLOW
BLUE
BLUE
ORANGE/BLACK
Horn Ring Out
Horn Ring In
Auxiliary
VIOLET
Backlight
GRAY
RADIO REBROADCAST
OUPUT LEVEL ADJUST
ORANGE/BLACK
ORANGE
BLACK
+V
5 amp
Fuse
WHITE
WHITE/
BLACK
+V
RED
SPEAKER
CN6
CN2
20 amp
Fuse
ORANGE
ORANGE/ BLACK

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 5
To Device requiring power
only when Ignition Switch
is on
From Siren
Switch Output
+V when Ignition
Switch is ON
NORMALLY OPEN
CONTACT RELAY
1 Amp
11
22
3
5
50A
FUSE
50A
FUSE
Slide Switch Level 3 Output
YELLOW
GREEN
BLUE
RED
RED
GREEN/WHITE
GREEN
RED
GREY
VIOLET
WHITE
Relay #9 Output for
2 wire Arrow Control Interface
Auxiliary Push Button #8
Normally Closed Output
Slide Switch Level Outputs 1-3 and Button Outputs 1-6 are
active high (vehicle supply level).
G
G
G
Wire Length Minimum Wire Gauge
0-10 Feet 10 AW
10-15 Feet 8 AW
15-25 Feet 6 AW
25+ Feet Consult Factory
Wire capacity requirements for Relay
incoming power supply for each wire
Internal Relay Board Fuse replacement:
To replace fuses:
1. Remove power connectors CN8 and CN6 or remove power
to unit.
2. Remove unit from console or obtain access to full top of unit.
3. Depress snaps on top cover and lift open.
4. See chart below for output fuse locations and ratings.
5. Fuse Ratings: Replace with same rated part.
6. Close cover, reinstall connectors and reinstall unit in console.
The button outputs 7 and 8 have the ability to receive power from
an independent external power source or from the internal +V as
supplied to CN8. Both of these outputs use a separate internal
10A mini-ATO fuse which rely on position to determine the source
selection. Each fuse may be placed in one of 2 locations. See
diagram below.
*If the fuse is placed in the fuse holder near the back edge
of the PCB that output will be powered from an external source,
labeled “relay #(x) input” on CN3.
** If the fuse is placed in the fuse holder away from the back
edge of the PCB that output will be powered from the internal +V
source that comes from CN8 pin 5.
**INTERNAL
*EXTERNAL
RED/ BLACK
GREEN/ BLACK
RED/ WHITE
ORANGE
YELLOW
BROWN
BLUE
Auxiliary Push-Button 7 Normally Open Output
Auxiliary Push-Button 8 Normally Open Output
Auxiliary Push-Button 7 Normally Closed Output
Push-Button 4
Push-Button 3
Push-Button 2
Push-Button 1
Slide Switch Level 2 Output
Slide Switch Level 1 Output
+ V
+ V
CN3
CN8 CN5
FUSE LOCATIONS ON RELAY PCB
FUSE CHART
LOCATION RATING
FB-8 10A
FB-7 10A
FB-4 10A
FB-3 10A
FB-2 10A
FB-1 10A
FB-5 10A
FB-6 10A
FB-9 10A
FS-1 20A
FS-2 20A
FS-3 20A
AUXILARY PUSH BUTTON
8 7 4 3 2 1 5 6 9
SLIDE SWITCH
1 2 3
N.C.
Relay #8 Input
Relay #7 Input
Auxiliary Push Button #6 Output
Auxiliary Push Button #5 Output
RJ45 Cable to Control Panel
400 SERIES AMPLIFIER BOX
PSRN4ANR1
POWERED
OUTPUT WIRING CONTROL PANEL
PCPRSP01
5 4 3 2 1
NOTICE:
When an output is connected to a
device which is required to function
only when ignition switch is ON, a
relay needs to be installed in-line with
the siren switch output to ensure an
operator can’t activate the device
without the ignition switch ON.
See wiring diagram details:

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 6
NOTE: For All programming modes: Momentarily depress
Radio Rebroadcast push-button to exit.
To hear samples of all the tones available go to www.
soundoffsignal.com website.
GRAYED AREAS DENOTE FACTORY DEFAULTS
LEGEND:
ON

OFF

NOT APPLICABLE
PROGRAMMING MANUAL
!
WARNING
Sirens produce loud sounds that
may damage hearing:
- Roll up windows.
- Wear hearing protection.
- Use only for emergency response.
- Avoid exposure to siren sound
outside of vehicle.
D1_Remote Console Panel Assy
MATERIAL:
THIRD ANGLE
PROJECTION
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN
THIS DRAWING IS THE SOLE
PROPERTY OF SOUNDOFF SIGNAL.
ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
SOUNDOFF SIGNAL IS PROHIBITED.
®
REVISION:
DESCRIPTION:
SHEET
1 OF 1
DRAWING
SIZE:
DO NOT SCALE
TOLERANCES
EXCEPT AS NOTED
.X ± .020
.XX ± .012
.XXX ± .006
ANGLES ± .5°
PRIMARY DIMS: INCH
DUAL DIMS: [mm]
A
DRAWING NO:
A A
B B
C C
D D
E E
5
5
4
4
3
3
2
2
1
1
GD&T TO FOLLOW
ASME Y14.5M-2009
CAD DIMENSIONS ARE BASIC
UNLESS OTHERWISE SPECIFIED
REMOTE CONTROL PANEL
ETCPRSP01 - 8 Button Controller w/ Radio Rebroadcast and Slide Switch

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 7
SLIDE SWITCH SETTINGS:
1. Press and hold Auxiliary Push-Button “1” and “4” until slide switch #2 indicator LED ashes.
2. Press Auxiliary Push-Button “1”, “2” or “3” depending on which conguration for the slide
switch is required.
HIGH
LOW 2
65
3
7
4
Setting PA Volume:
1. Press and Hold Auxiliary Push-Button “1” and “2” until slide switch #2 and #3 indicator LED
ashes.
2. Depress and hold PA switch on microphone and press Push-button “1”-“8” depending on
volume required. When correct volume is determined, press Radio Rebroadcast and
the volume setting will be permanently stored. BACKLIGHT INTENSITY:
While pressing Radio Rebroadcast Button,
press Auxiliary Button 1-8 to adjust backlight intensity.
Button 1 = Lowest intensity, Button 8 = Highest intensity.
Backlight must be enabled by the Gray wire on CN6.
SLIDE SWITCH SETTINGS
MODE
RELAY
OUTPUT
#1
RELAY
OUTPUT
#2
RELAY
OUTPUT
#3
SLIDE
SWITCH
POSITION
1AUXILIARY PUSH-BUTTON ‘1’ IS SELECTED
1
  2
   3
2AUXILIARY PUSH-BUTTON ‘2’ IS SELECTED
1
2
3
3AUXILIARY PUSH-BUTTON ‘3’ IS SELECTED
1
2
   3
AUXILIARY SWITCH SETTINGS:
Refer to Siren Amplier Diagnostic Indicator Chart below for Button and LED locations and
terminology
1. Press and Hold Auxiliary Button #1 and #8 until slide switch #1 LED ashes.
2. Press the button which setting is going to be viewed/changed 1 time.
3. Monitor the 5 LED’s for the arrow controller to determine setting
- *Arrow Controller (Left, Right, Center, OFF), Dual Output; 1 & 9
- Alternate Action Switch (Press ON / Press OFF)
- Momentary Action Switch (ON only when depressed)
- 8 Second ON Time (ON for 8 seconds when depressed)
- Level 1 Disable (Turns OFF Level 1 Output)
- Level 2 Disable (Turns OFF Level 2 Output)
- Left Arrow, Single Output
- Right Arrow, Single Output
- Center Arrow, Single Output
- Warning Bar Output
4. Press and release button until desired mode is selected.
5. Continue steps 2-3 for any other buttons that need to be programmed.
*Can only be programmed to one button
and will disable Left, Right and Center
Arrow Single Outputs if they are used.
PROGRAMMING MODES
Default Settings:
Button #1: Arrow Controller
Button #2-7: Alternate Action Switch
Button #8: 8 Second Gun Lock
REMOTE CONTROL PANEL
ETCPRSP01 - 8 Button Controller w/ Radio Rebroadcast and Slide Switch

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 8
Allows the operator to have the siren automatically turn on auxiliary push-buttons based on the position
of the slide switch.
If an auxiliary push-button is programmed to turn ON when the slide switch position is selected,
the auxiliary push-button will turn OFF when the programmed slide switch position is no longer
selected.
The operator can override the automatic activation of the auxiliary push-button by momentarily
pressing the auxiliary push-button.
To program:
1. Press auxiliary push-buttons ‘4’ and ‘5’ for 2 seconds until Radio Rebroadcast indicator LED ashes.
2. Move slide switch to desired position.
3. Press auxiliary push-buttons ‘1’ – ‘8’, as required.
4. Repeat steps 2 and 3 for other slide switch positions as required.
5. Place appropriate button legend over activity indicator for each programmed button.
PARK KILL SETTINGS:
Press and Hold Auxiliary Button 1 and 3 until slide switch #3 LED ashes.
Enables auxiliary outputs to be disabled when Park Kill input is active. Auxiliary outputs can be
turned back on by pushing the buttons again.
LED ON
(GREEN)
Auxiliary push-button will automatically turn
ON when level switch position is activated.
LED OFF
(RED OR OFF)
Auxiliary push-button will NOT automatically
turn ON when level switch position is
activated.
2. SLIDE SWITCH ENABLED WITHOUT IGNITION: After ignition is turned off, device will stay
on in lower power mode and allow (ONLY the slider to operate.)
ON = With ignition off, slider relays will still turn on if slider is in
position 1, 2, or 3. Device will turn off if no ignition after 18
hours, or if battery is below 10.5V after 2 hours.
OFF = Device turns off normally, sliders will not work when off.
ALTERNATE MODES:
Press and Hold Auxiliary Button “2” and “6” until Slide Switch indicator #1 and indicator #2 LED
ashes.
1. DISABLE RELAY ERROR FOR AUX 7 & 8:
ON = Disable fault detect indication for Aux relays 7& 8.
OFF= Fault detect normal.
OTHER MODES:
Press and Hold Auxiliary Button “1” and “5” until slide switch #1 and #3 indicator LED ashes.
2. Power Down: Determines siren operation after ignition wire input has no voltage.
ON = Timed Power Down: Siren will power down 10 min. after last
activity.
OFF = Immediate Power Down: Siren will go into lowest power state
within 10 seconds.
1. Buzzer: Audible tone from control panel whenever operator presses push-button or changes
position of slide/rotary switch.
ON = Buzzer enabled.
OFF = Buzzer disabled.
3. 8 Second Buzzer alert: Provides audible beep whenever any auxiliary switches are ON or level
1,2, or 3 is active.
ON = Enabled.
OFF = Disabled.
SLIDE SWITCH MAPPING PROGRAMMING:
1. Park Kill Polarity Mode: Determines what voltage level will activate park kill functions.
ON = activated when +V is applied to Park Kill input wire.
OFF = activated when Ground is applied to Park Kill input wire.
2. Press the Radio Rebroadcast button to exit programming mode.
3. Push and hold Auxiliary Push-Buttons 2 & 3 until arrow indicator LEDs ash.
4. Press Push-Buttons 1-8 to toggle whether that auxiliary output will turn off when Park Kill input
becomes active. LED on means output will turn off.
5. Press the Radio Rebroadcast button to exit programming mode.
REMOTE CONTROL PANEL
ETCPRSP01 - 8 Button Controller w/ Radio Rebroadcast and Slide Switch

ETCPRSP01 0718
1.800.338.7337 / www.soundoffsignal.com
Pg. 9
Dielectric Grease on Molex Connectors
Introduction
Molex has advised to add dielectric grease for “Mini-Fit
Sr.” connectors. On the SoundOff Signal 400 Series Sirens
this includes the Connector (CN8) on the back of the siren.
Connector CN8 is used on the 400 Series Sirens to supply
power to the Slide and Auxiliary outputs of the siren.
This connector is a member of the “Mini-Fit Sr.” family
manufactured by Molex. The dielectric grease / lubricant
should be applied to these tin-plated terminals that are
used for CN8 and/or the mating connector included with
the Siren. The application of the grease should take no
more than 5 minutes for each siren.
Application Instruction
The dielectric grease should be applied after all crimping,
soldering, and assembly is complete. It should be applied
to all ve (5) terminals. Care must be taken to prevent any
scratching or damage to the plating in the contact area.
Avoid contamination from dust, dirt, or other materials.
Molex recommends Nye lubricant, Nyogel 760G
and provides detailed instructions in this application
specication:
https://www.molex.com/pdm_docs/as/AS-42815-001.
pdf
A single use packet of Nyogel 760G has been included in
the siren harness kit for application.
NYLEX SAFETY DATA SHEET: https://www.nyelubricants.
com/datasheet/SDS_US_English_NYOGEL+760G.pdf
NOTE:
The mating harness that has been included in the kit
uses correctly matched tin plated terminals. Do not
mix terminals with other plating types such as silver or
gold.
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to [e-mail].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
!
WARNING
!
Dialectric grease must be applied to
connector CN8.
400 SERIES REMOTE SIREN
W/ 380R REMOTE CONTROL PANEL
ETSA481RSP - 100W
ETSA482RSP - 200W