Soundoff Signal EL3SSCW User manual

NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
EL3SSCW 0418
OPERATION:
NOTE: The LED3 is a factory sealed unit
that CANNOT be serviced in the field.
Any attempt to gain access to the LED3
unit will most likely cause permanent
damage and void its warranty.
IMPORTANT: DO NOT connect this
device to a strobe power supply.
OPERATING INSTRUCTIONS
1. Connect the LED3 BLACK wire to a
good, convenient ground.
2. Connect the LED3 RED wire to one
side of a user supplied on/off switch.
Connect the other side of the switch,
through a 5Amp fuse, to a source of
+Vdc power.
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into the
light beam at close range.
INSTALLATION:
IMPORTANT: DO NOT over tighten
mounting screws or nuts. This could
cause permanent damage to the light.
1. Locate flat mounting location for the
LED3 Light.
2. When the position of LED3 is
determined use paper template on
next page to drill hole locations.
Screw mounting holes should be
drilled using a 3/32” drill bit. Wire
entry holes should be drilled using a
1/4” drill bit.
3. Make electrical connections.
4. Using supplied #6 x 3/4” screws,
fasten LED3 to mounting surface. Be
sure not to overtighten screws as this
will cause hole in mounting surface
to strip out. Be sure that supplied
gasket is mounted between mounting
surface and LED3.
LED3 SURFACE MOUNT SPOTLIGHT
WIDE ANGLE OPTICS/STEADY BURN
EL3SSCW 10-16Vdc
EL3SS30CW 10-30Vdc
SUPPLIED GASKET
2x SUPPLIED #6x3/4”
SHEET METAL SCREWS
WIRE HOOK-UP TABLE
WIRE COLOR: CONNECT TO:
RED Power (+Vdc)
BLACK Ground (-)
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat
build-up and re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle
Owner’s Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal
or local chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at
power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING Please see next page for Technical Specications

TECHNICAL SPECIFICATIONS
Overall Dimensions: 2.5”W x 1.375”H x 1.25”D
Input Voltage Range: 10-16Vdc OR 10-30Vdc
Current Consumption: <0.4 amps
Light Sync Technology: No
# of LEDs: 3 Generation 3 LEDs
Operating Temperature: -40º to +65º C
TO USE THE ABOVE LAYOUT AS A TEMPLATE MEASURE THE
LINE BELOW. IF THE SCALE IS CORRECT THE LINE WILL BE 3”
LONG. IF IT IS NOT, ENLARGE OR REDUCE ON A COPIER CAPABLE
OF SUCH SCALING.
Drill Template for Mounting Holes/Cord Entry (See note
below)
LED3 SURFACE MOUNT SPOTLIGHT
WIDE ANGLE OPTICS/STEADY BURN
EL3SSCW 10-16Vdc
EL3SS30CW 10-30Vdc
2.21
1.09
0.73 1.48
0.23
2x 3/32"
2x
3/32"
0.25
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at www.soundoffsignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. or after hours 5 p.m. to 8 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to [email protected].
SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.
EL3SSCW 0418