manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Soundstream
  6. •
  7. Subwoofer
  8. •
  9. Soundstream SPLX-12 User manual

Soundstream SPLX-12 User manual

Parallel Wiring of Dual Voice Coils (1 Woofer)
Parallel Wiring of Dual Voice Coils (2 Woofers)
Series Wiring of Dual Voice Coils (1 Woofer)
Series/Parallel Wiring of Dual Voice Coils (2 Woofers)
Owner's manual
REV 011106JMH
SOUNDSTREAM SPLX Woofer
Thiele / Small Parameters SPLX-122
Design Features
Cast Aluminum Basket
Kevlar/Paper Mix Cone
UV Coated Foam Surround
1-Piece Rubber Gasket
Gold Plated Push Terminals
Building the Enclosure
Recommended wiring
Optimum
Minimum
1 cubic foot
.75 cubic feet
Recommended box sizes
Sealed Enclosure Recommendations
Vented Enclosure Recommendations
SPLX 12
RMS Power (Watts)
VOICE COIL DIAMETER (INCHES)
VOICE COIL IMPEDANCE (INCHES)
WOOFER DISPLACEMENT (FT3)
MAGNET WEIGHT (oz)
FREQUENCY RESPONSE (Hz)
Fs (Hz)
Qes
Qms
Qts
Vas (Ft3)
Xmax (in.)
SPL (dB)
HOLE SIZE (INCHES)
WOOFER DEPTH (INCHES)
750
3
DUAL 2 Ohm
0.1
192
25-300
35
0.342
5.387
0.322
1.42
0.565
89
11.25
7.25
If you are an enthusiast that plays your system loud and hard, the SPLX
Woofers will take you to the next level. Capable of working in small
enclosures for audiophiles and large vented for SPLX Max “Bass Heads”,
this is woofer was a great a choice if you are serious about your sound.
We ask that you take a moment to read through the entire manual
before installing the woofer to familiarize your self with the connection
procedure as well as determining the best fit enclosure for you and your
vehicle’s application.
Congratulations and Thank You for you purchase of an SPLX Woofer. We
are confidant you will enjoy the performance of this woofer for many
years.
First determine the dimensions of your enclosure. Be certain the box
dimensions that you have designed will fit in the locations you have
chosen. Sometimes, making a cardboard box with the identical outer
dimensions is helpful to confirm it will fit properly. We recommend using
.75” thick MDF (Medium Density Fiberboard) to build your speaker box
with.
Use a “T-Square” to verify you have cut all your precise right angles
before you assemble the box completely. Use high quality wood glue
along with nails and screws for proper assembly.
Apply a sealant to all of the inside corners of the enclosure to assure
proper sealing of the box.
It is recommended to stuff a sealed enclosure with approximately 50%
fill (DACRON or Polyester Insulation) for damping purposes.
Strip off approximately .5”/13mm of wire insulation to assure the bare
wire lead penetrates all the way through the push terminal. Follow by
using additional sealant around the wire lead exiting the enclosure or
around the terminal cup if one is being used.
NOTE: A mathematical reference to determining impedance of multiple coils in one
circuit is to DIVIDE the Impedance of the coils by their quantity when connected in
Parallel or simply add the impedance in a concurrent matter if you series the coils in
a circuit.
The following page explains a few different methods for you to match
the impedance of the woofer(s) to the optimum or near best capabili-
ties of your amplifier. It is your responsibility to calculate the correct load
for your amp. Please take a moment to read through the diagrams to
insure maximum performance of your woofers and amplifier(s).
Optimum
Minimum
Port (dia x length) Qty of Port(s)Tune Freq.F3Required Airspace
2 cubic foot
1.5 cubic foot36Hz
36Hz
33Hz
33Hz
1
3
4" x 12"
4" x 18"
2 ohm LOAD
Amplifier
4 ohm
Woofer
4 ohm
1 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier
4 ohm
Woofer
4 ohm
Amplifier
8 ohm LOAD
4 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier
Parallel Wiring of Dual Voice Coils (1 Woofer)
Parallel Wiring of Dual Voice Coils (2 Woofers)
Series Wiring of Dual Voice Coils (1 Woofer)
Series/Parallel Wiring of Dual Voice Coils (2 Woofers)
Owner's manual
REV 011106JMH
SOUNDSTREAM SPLX Woofer
Design Features
Cast Aluminum Basket
Kevlar/Paper Mix Cone
UV Coated Foam Surround
1-Piece Rubber Gasket
Gold Plated Push Terminals
Building the Enclosure
Recommended wiring
Optimum
Minimum
1.75 cubic feet
1.2 cubic feet
Recommended box sizes
Sealed Enclosure Recommendations
Vented Enclosure Recommendations
SPLX 15
1000
3
DUAL 2 Ohm
0.13
192
20-300
38
0.465
4.594
0.422
2.31
0.565
91
14.25
8.125
Thiele / Small Parameters SPLX-152
RMS Power (Watts)
VOICE COIL DIAMETER (INCHES)
VOICE COIL IMPEDANCE (INCHES)
WOOFER DISPLACEMENT (FT3)
MAGNET WEIGHT (oz)
FREQUENCY RESPONSE (Hz)
Fs (Hz)
Qes
Qms
Qts
Vas (Ft3)
Xmax (in.)
SPL (dB)
HOLE SIZE (INCHES)
WOOFER DEPTH (INCHES)
If you are an enthusiast that plays your system loud and hard, the SPLX
Woofers will take you to the next level. Capable of working in small
enclosures for audiophiles and large vented for SPLX Max “Bass Heads”,
this is woofer was a great a choice if you are serious about your sound.
We ask that you take a moment to read through the entire manual
before installing the woofer to familiarize your self with the connection
procedure as well as determining the best fit enclosure for you and your
vehicle’s application.
Congratulations and Thank You for you purchase of an SPLX Woofer. We
are confidant you will enjoy the performance of this woofer for many
years.
First determine the dimensions of your enclosure. Be certain the box
dimensions that you have designed will fit in the locations you have
chosen. Sometimes, making a cardboard box with the identical outer
dimensions is helpful to confirm it will fit properly. We recommend using
.75” thick MDF (Medium Density Fiberboard) to build your speaker box
with.
Use a “T-Square” to verify you have cut all your precise right angles
before you assemble the box completely. Use high quality wood glue
along with nails and screws for proper assembly.
Apply a sealant to all of the inside corners of the enclosure to assure
proper sealing of the box.
It is recommended to stuff a sealed enclosure with approximately 50%
fill (DACRON or Polyester Insulation) for damping purposes.
Strip off approximately .5”/13mm of wire insulation to assure the bare
wire lead penetrates all the way through the push terminal. Follow by
using additional sealant around the wire lead exiting the enclosure or
around the terminal cup if one is being used.
NOTE: A mathematical reference to determining impedance of multiple coils in one
circuit is to DIVIDE the Impedance of the coils by their quantity when connected in
Parallel or simply add the impedance in a concurrent matter if you series the coils in
a circuit.
The following page explains a few different methods for you to match
the impedance of the woofer(s) to the optimum or near best capabili-
ties of your amplifier. It is your responsibility to calculate the correct load
for your amp. Please take a moment to read through the diagrams to
insure maximum performance of your woofers and amplifier(s).
Optimum
Minimum
Port (dia x length) Qty of Port(s)Tune Freq.F3Required Airspace
3 cubic feet
2 cubic feet34Hz
34Hz
47Hz
45Hz
1
2
4" x 11.25"
4" x 16"
2 ohm LOAD
Amplifier
4 ohm
Woofer
4 ohm
1 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier
4 ohm
Woofer
4 ohm
Amplifier
8 ohm LOAD
4 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier
Parallel Wiring of Dual Voice Coils (1 Woofer)
Parallel Wiring of Dual Voice Coils (2 Woofers)
Series Wiring of Dual Voice Coils (1 Woofer)
Series/Parallel Wiring of Dual Voice Coils (2 Woofers)
Owner's manual
REV 011106JMH
SOUNDSTREAM SPLX Woofer
Thiele / Small Parameters SPLX-124
Design Features
Cast Aluminum Basket
Kevlar/Paper Mix Cone
UV Coated Foam Surround
1-Piece Rubber Gasket
Gold Plated Push Terminals
Building the Enclosure
Recommended wiring
Optimum
Minimum
1 cubic foot
.75 cubic feet
Recommended box sizes
Sealed Enclosure Recommendations
Vented Enclosure Recommendations
SPLX 124
1000
3
QUAD 2 Ohm
.10
192
25-300
29
.294
5.887
.280
1.42
.565
87
11.25
7.25
RMS Power (Watts)
VOICE COIL DIAMETER (INCHES)
VOICE COIL IMPEDANCE (INCHES)
WOOFER DISPLACEMENT (FT3)
MAGNET WEIGHT (oz)
FREQUENCY RESPONSE (Hz)
Fs (Hz)
Qes
Qms
Qts
Vas (Ft3)
Xmax (in.)
SPL (dB)
HOLE SIZE (INCHES)
WOOFER DEPTH (INCHES)
If you are an enthusiast that plays your system loud and hard, the SPLX
Woofers will take you to the next level. Capable of working in small
enclosures for audiophiles and large vented for SPLX Max “Bass Heads”,
this is woofer was a great a choice if you are serious about your sound.
We ask that you take a moment to read through the entire manual
before installing the woofer to familiarize your self with the connection
procedure as well as determining the best fit enclosure for you and your
vehicle’s application.
Congratulations and Thank You for you purchase of an SPLX Woofer. We
are confidant you will enjoy the performance of this woofer for many
years.
First determine the dimensions of your enclosure. Be certain the box
dimensions that you have designed will fit in the locations you have
chosen. Sometimes, making a cardboard box with the identical outer
dimensions is helpful to confirm it will fit properly. We recommend using
.75” thick MDF (Medium Density Fiberboard) to build your speaker box
with.
Use a “T-Square” to verify you have cut all your precise right angles
before you assemble the box completely. Use high quality wood glue
along with nails and screws for proper assembly.
Apply a sealant to all of the inside corners of the enclosure to assure
proper sealing of the box.
It is recommended to stuff a sealed enclosure with approximately 50%
fill (DACRON or Polyester Insulation) for damping purposes.
Strip off approximately .5”/13mm of wire insulation to assure the bare
wire lead penetrates all the way through the push terminal. Follow by
using additional sealant around the wire lead exiting the enclosure or
around the terminal cup if one is being used.
NOTE: A mathematical reference to determining impedance of multiple coils in one
circuit is to DIVIDE the Impedance of the coils by their quantity when connected in
Parallel or simply add the impedance in a concurrent matter if you series the coils in
a circuit.
The following page explains a few different methods for you to match
the impedance of the woofer(s) to the optimum or near best capabili-
ties of your amplifier. It is your responsibility to calculate the correct load
for your amp. Please take a moment to read through the diagrams to
insure maximum performance of your woofers and amplifier(s).
Optimum
Minimum
Port (dia x length) Qty of Port(s)Tune Freq.F3Required Airspace
2 cubic foot
1.5 cubic foot36Hz
36Hz
33Hz
33Hz
1
3
4" x 12"
4" x 18"
2 ohm LOAD
Amplifier
4 ohm
Woofer
4 ohm
1 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier
4 ohm
Woofer
4 ohm
Amplifier
8 ohm LOAD
4 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier
Parallel Wiring of Dual Voice Coils (1 Woofer)
Parallel Wiring of Dual Voice Coils (2 Woofers)
Series Wiring of Dual Voice Coils (1 Woofer)
Series/Parallel Wiring of Dual Voice Coils (2 Woofers)
Owner's manual
REV 011106JMH
SOUNDSTREAM SPLX Woofer
Design Features
Cast Aluminum Basket
Kevlar/Paper Mix Cone
UV Coated Foam Surround
1-Piece Rubber Gasket
Gold Plated Push Terminals
Building the Enclosure
Recommended wiring
Optimum
Minimum
1.75 cubic feet
1.2 cubic feet
Recommended box sizes
Sealed Enclosure Recommendations
Vented Enclosure Recommendations
SPLX 154
1000
3
QUAD 2 Ohm
.13
192
20-300
34
.388
5.041
.360
2.31
.565
90
14.25
8.125
Thiele / Small Parameters SPLX-154
RMS Power (Watts)
VOICE COIL DIAMETER (INCHES)
VOICE COIL IMPEDANCE (INCHES)
WOOFER DISPLACEMENT (FT3)
MAGNET WEIGHT (oz)
FREQUENCY RESPONSE (Hz)
Fs (Hz)
Qes
Qms
Qts
Vas (Ft3)
Xmax (in.)
SPL (dB)
HOLE SIZE (INCHES)
WOOFER DEPTH (INCHES)
If you are an enthusiast that plays your system loud and hard, the SPLX
Woofers will take you to the next level. Capable of working in small
enclosures for audiophiles and large vented for SPLX Max “Bass Heads”,
this is woofer was a great a choice if you are serious about your sound.
We ask that you take a moment to read through the entire manual
before installing the woofer to familiarize your self with the connection
procedure as well as determining the best fit enclosure for you and your
vehicle’s application.
Congratulations and Thank You for you purchase of an SPLX Woofer. We
are confidant you will enjoy the performance of this woofer for many
years.
First determine the dimensions of your enclosure. Be certain the box
dimensions that you have designed will fit in the locations you have
chosen. Sometimes, making a cardboard box with the identical outer
dimensions is helpful to confirm it will fit properly. We recommend using
.75” thick MDF (Medium Density Fiberboard) to build your speaker box
with.
Use a “T-Square” to verify you have cut all your precise right angles
before you assemble the box completely. Use high quality wood glue
along with nails and screws for proper assembly.
Apply a sealant to all of the inside corners of the enclosure to assure
proper sealing of the box.
It is recommended to stuff a sealed enclosure with approximately 50%
fill (DACRON or Polyester Insulation) for damping purposes.
Strip off approximately .5”/13mm of wire insulation to assure the bare
wire lead penetrates all the way through the push terminal. Follow by
using additional sealant around the wire lead exiting the enclosure or
around the terminal cup if one is being used.
NOTE: A mathematical reference to determining impedance of multiple coils in one
circuit is to DIVIDE the Impedance of the coils by their quantity when connected in
Parallel or simply add the impedance in a concurrent matter if you series the coils in
a circuit.
The following page explains a few different methods for you to match
the impedance of the woofer(s) to the optimum or near best capabili-
ties of your amplifier. It is your responsibility to calculate the correct load
for your amp. Please take a moment to read through the diagrams to
insure maximum performance of your woofers and amplifier(s).
Optimum
Minimum
Port (dia x length) Qty of Port(s)Tune Freq.F3Required Airspace
3 cubic feet
2 cubic feet34Hz
34Hz
47Hz
45Hz
1
2
4" x 11.25"
4" x 16"
2 ohm LOAD
Amplifier
4 ohm
Woofer
4 ohm
1 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier
4 ohm
Woofer
4 ohm
Amplifier
8 ohm LOAD
4 ohm LOAD
4 ohm
Woofer
4 ohm 4 ohm
Woofer
4 ohm
Amplifier

Other Soundstream Subwoofer manuals

Soundstream XPRO-10 User manual

Soundstream

Soundstream XPRO-10 User manual

Soundstream T5 Series T5-10 User manual

Soundstream

Soundstream T5 Series T5-10 User manual

Soundstream SM16-90 User manual

Soundstream

Soundstream SM16-90 User manual

Soundstream SPL 15 Programming manual

Soundstream

Soundstream SPL 15 Programming manual

Soundstream RUBICON RUB.102 User manual

Soundstream

Soundstream RUBICON RUB.102 User manual

Soundstream X3-122 Technical manual

Soundstream

Soundstream X3-122 Technical manual

Soundstream Granite Pro10 Programming manual

Soundstream

Soundstream Granite Pro10 Programming manual

Soundstream Stealth-124 User manual

Soundstream

Soundstream Stealth-124 User manual

Soundstream EXC 10 Service manual

Soundstream

Soundstream EXC 10 Service manual

Soundstream Arachnid SW-12RE Owner's manual

Soundstream

Soundstream Arachnid SW-12RE Owner's manual

Soundstream PXW 15 User manual

Soundstream

Soundstream PXW 15 User manual

Soundstream SPL 170 Programming manual

Soundstream

Soundstream SPL 170 Programming manual

Soundstream SPL 170 Programming manual

Soundstream

Soundstream SPL 170 Programming manual

Soundstream SM-10W User manual

Soundstream

Soundstream SM-10W User manual

Soundstream R1.122 Service manual

Soundstream

Soundstream R1.122 Service manual

Soundstream Reference R1 Manual

Soundstream

Soundstream Reference R1 Manual

Soundstream USA-10 Programming manual

Soundstream

Soundstream USA-10 Programming manual

Soundstream Tarantula TSQ102 User manual

Soundstream

Soundstream Tarantula TSQ102 User manual

Soundstream Picasso PCO-8 User manual

Soundstream

Soundstream Picasso PCO-8 User manual

Soundstream Tarantula T5 User manual

Soundstream

Soundstream Tarantula T5 User manual

Soundstream Reference Series SS-10R User manual

Soundstream

Soundstream Reference Series SS-10R User manual

Soundstream Subwoofers Service manual

Soundstream

Soundstream Subwoofers Service manual

Soundstream Tarantula TRX1000D User manual

Soundstream

Soundstream Tarantula TRX1000D User manual

Soundstream VGW-10 User manual

Soundstream

Soundstream VGW-10 User manual

Popular Subwoofer manuals by other brands

Focal 13 KS manual

Focal

Focal 13 KS manual

Eclipse TD725SW - brochure

Eclipse

Eclipse TD725SW - brochure

Sony SAW2500 - SA Subwoofer Specifications

Sony

Sony SAW2500 - SA Subwoofer Specifications

JL Audio Stealthbox SB-N-TTCRW/10W3v2 installation guide

JL Audio

JL Audio Stealthbox SB-N-TTCRW/10W3v2 installation guide

JL Audio Fathom f113v2 owner's manual

JL Audio

JL Audio Fathom f113v2 owner's manual

sky-tec SMWA15 instruction manual

sky-tec

sky-tec SMWA15 instruction manual

Klipsch PRO-1000SW owner's manual

Klipsch

Klipsch PRO-1000SW owner's manual

Boston Acoustics Voyager Voyager 1 user guide

Boston Acoustics

Boston Acoustics Voyager Voyager 1 user guide

D.A.S. LX-218CA user manual

D.A.S.

D.A.S. LX-218CA user manual

Alto BLACK 15 SUB Service manual

Alto

Alto BLACK 15 SUB Service manual

AED AUDIO SOLID28 user manual

AED

AED AUDIO SOLID28 user manual

Profile California W10 Installation instructions and owner's manual

Profile

Profile California W10 Installation instructions and owner's manual

Alpine SWE-1200 owner's manual

Alpine

Alpine SWE-1200 owner's manual

MK Sound MX-350THX Operation manual

MK Sound

MK Sound MX-350THX Operation manual

Xtant X2.1004 Specifications

Xtant

Xtant X2.1004 Specifications

JVC TH-M337B user manual

JVC

JVC TH-M337B user manual

Focal Sub 10 Dual user manual

Focal

Focal Sub 10 Dual user manual

All OSD Audio In-Wall Subwoofer IWS-10 owner's manual

All OSD Audio

All OSD Audio In-Wall Subwoofer IWS-10 owner's manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.