Speakman BIDET REMOTE User manual

INSTRUCTIONS FOR MODELS
LIGHT
SEAT TEMPWATER TEMP DRYER TEMP
92-BIDET-REMOTE-01
For additional assistance or service please contact:
SPEAKMAN®
800-537-2107
customerser[email protected]
www.speakman.com
BIDET REMOTE
TOOLS AND SUPPLIES
Measuring
Tape
Drill Drill Bit
1/4”
Pencil Phillips
Screwdriver
IMPORTANT
SAFETY TIPS
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
MAINTENANCE
Your new Speakman Product is designed for years
of trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of
harsh chemicals and abrasives on any of the
Speakman custom finish products may damage the
finish and void the product warranty. Please be sure
to only use approved cleaners. Please contact
Speakman for any clarification of acceptable
cleaners.
WARRANTY
1 Year Limited Warranty
Warranty information can be found at:
www.speakman.com
IMPORTANT! Do NOT install unit where it may come in direct contact with water.
INSTALLING THE WALL BRACKET WITH SCREWS
1. Place the Remote Control Hanger upright on the
Per-determined area of the wall and mark the
location of the two mounting holes on the wall with
a pencil.
• Drill a hole in the marked position on the wall with
a 1/4" Drill Bit, with a depth of 1-3/8".
NOTE: Location of Wall Mount Bracket should be
accessible while seated on the Bidet.
2. Push the Anchors into the drilled holes and ensure
they are fully inserted and flush to the wall surface.
• Position the Wall Bracket over the Anchors and
secure into position with the included Screws. Cover
the screw heads with the included Caps.
3. Install 3 AAA batteries into the Remote Control
and replace cover.
4. Place the Remote Control into the Wall Bracket.
LIGHT

IMPORTANT! Ensure mounting location is smooth and capable of accepting adhesive mounting.
Do NOT install unit where it may come in direct contact with water.
INSTALLING THE WALL BRACKET WITH ADHESIVE
1. Properly clean the determined mounting area.
NOTE: Location of wall mount bracket should be
accessible while seated on the Bidet.
2. Remove the paper backing from the Adhesive
Tape. Align Wall Bracket to the desired mounting
position, and firmly press into position. Cover the
Mounting Holes with the included Caps.
3. Install 3 AAA batteries into the Remote Control
and replace cover.
4. Place the Remote Control into the Wall Bracket.
REMOTE CONTROL ICON FUNCTIONS
REAR CLEANING/MASSAGE
INCREASE WATER FLOW
FRONT CLEANING/MASSAGE
DECREASE WATER FLOW
DRYING
AUTO REAR CLEANING
INDICATOR LIGHT
(Only Visible When
The Light Is On)
DRYER TEMPERATURE
WATER TEMPERATURE
NIGHT LIGHT
MOVE NOZZLE FORWARD
MOVE NOZZLE REARWARD
AUTO FRONT CLEANING
STOP/ENERGY SAVER
SEAT TEMPERATURE
SEAT TEMPWATER TEMP DRYER TEMP
* Models without drying
function will not have
this button
* Models without drying
function will not have
this button
PULSATE CLEAN
* Models without
Pulsate clean function
will not have this button
HEATED/COOLED CLEAN
*Models without HEATED/
COOLED CLEAN will not have
this button.
LIGHT
LIGHT
INSTALLATION
AREA

USAGE INSTRUCTIONS
REAR CLEANING
• Press "REAR/MOVE" button. Remote will
illuminate to show you the water temperature and
start the rear cleaning process.
• Pressing the "REAR/MOVE" button a second
time will engage the MASSAGE feature. This will
move the cleaning nozzle forwards and
backwards while cleaning.
• The cleaning cycle will stop automatically when
complete, or can be stopped at any time by
pressing the "STOP" button.
DRYING OPERATION (Only for toilets with drying function.)
• Press "Dry" button. The Remote will illuminate to show the drying air temperature and start the
drying process.
• The drying cycle will stop automatically when complete, or can be stopped at any time by leaving the
seated position.
NOTE: During front/rear cleaning, long press “Rear cleaning/massage” or “Front cleaning/massage”
button to turn ON/OFF pulse cleaning mode. (This function only applies to product with pulse cleaning
mode.)
FRONT CLEANING
• Press "FRONT/MOVE" button. Remote will
illuminate to show you the water temperature and
start the front cleaning process.
•Pressing the "FRONT/MOVE" button a second
time will engage the MASSAGE feature. This will
move the cleaning nozzle forwards and backwards
while cleaning.
• The cleaning cycle will stop automatically when
complete, or can be stopped at any time by
pressing the "STOP" button.
REAR/MOVE
PRESSURE POSITION
FRONT/MOVE
STOP
HOLD TO ECO
DRY
REAR
FRONT
DRY
USAGE INSTRUCTIONS
WATER FLOW ADJUSTMENT
• During the Rear or Front Cleaning process, pressing the "+" or "-" buttons will increase or decrease the
water flow and the remote will illuminate to show you the current setting.
PRESSURE POSITION
REAR/MOVE
FRONT/MOVE
DRY
NOZZLE
PULSATE CLEAN (This function only applies to products with the Pulsate clean function.)
• During the Rear or Front Cleaning process, pressing the "PULSATE CLEAN" button will alternate the water
pressure between strong/weak. This will continue until the end of the cleaning process, or can stopped by
pressing the "PULSATE CLEAN" button a second time.
HEAT & COLD CLEAN (This function only applies to product with Heat & Cold clean function.)
• During the Rear or Front Cleaning process, pressing the "H/C CLEAN" button will alternate the water
temperature between hot/cold. This will continue until the end of the cleaning process, or can be stopped by
pressing the "H/C CLEAN" button a second time.
SPRAY NOZZLE POSITION ADJUSTMENT
• During the Rear or Front Cleaning process, pressing the " " or " " buttons will adjust the spray
nozzle forward/backwards and the remote will illuminate to show you the current position. There are 5
levels of position adjustment.

USAGE INSTRUCTIONS
NOTE: The timing shown is the Maximum Cycle Time before the unit will switch to the next function or turn OFF if it is
on the last function in that process. User can press the Stop Button or Press the Knob to stop the cleaning function early.
MASSAGE CLEANING 30S
MASSAGE CLEANING 30S
AUTOMATIC STOP
AUTO REAR CLEANING REAR CLEANING 20S
DRY 180S
REAR CLEANING 40S
AUTO FRONT CLEANING FRONT CLEANING 20S
FRONT CLEANING 40S DRY 180S AUTOMATIC STOP
STOP
HOLD TO ECO
ENERGY SAVER
• Holding the "STOP" button for more than 3 seconds will place the unit into Energy Saving Mode. The
standard indicator light will turn off and the Energy Saving Mode indicator light will illuminate. Holding the
"STOP" button again for more than 3 seconds will exit Energy Saving Mode.
• Under energy saving mode, seat temperature is automatically adjusted to a low level to achieve energy
saving. (NOTE: If the seat temperature before energy saving is neutral, keep the neutral after energy saving)
IMPORTANT! Energy saving mode will be suspended and switch to standard mode if someone uses the
seat in the middle of energy saving. The seat will begin to heat immediately and the Energy Saving Mode
will automatically be engaged when the user leaves the seated position.
AUTO FUNCTION (Only for the units with the Auto Wash Function.)
• If your model includes the Auto Cleaning Function, a quick press of the " " or " " button will begin the
fully automatic cleaning process.
• The default settings for the Auto Cleaning Function place the water flow, spray nozzle position, water
temperature, drying air temperature, and seat temperature in the middle setting for each.
• You have the ability to customize and save your own Auto settings. Make your adjustments to the water
flow, nozzle position, water temperature, and air temperature settings. Holding the " " or " " button for
3 seconds will save your customized settings. During the next use, pressing the " " or " " will engage
your custom settings automatically.
NOTE: Certain models don’t have drying function.
TEMPERATURE ADJUSTMENT
WATER TEMPERATURE ADJUSTMENT
• Short press the “WATER TEMP” button to adjust the water temperature. The indicator will show the water
temperature level if it’s on. When the indicator is off, the water heating setting is 0. Short press this button to
adjust water temperature level from 0 to 5.
Note: The water temperature is approximately 50º Fahrenheit at setting "0". If the water temperature falls
below 50º Fahrenheit the heater will engage to bring the temperature back in range.
NIGHT LIGHT (Only for toilets with night light function.)
• Short press “Night light” button to turn on/turn off night light, long press “Night light” button to enter into
intelligent mode ( Night light will be on or off by detecting the lightness of surroundings). If the product is on
intelligent mode, short press “Night light” button to exit intelligent mode.
DRYER TEMPERATURE ADJUSTMENT (Only for toilets with drying function.)
• Short press the “DRYER TEMP” button to adjust the dryer temperature. The indicator will show the dryer
temperature level if it’s on. When the indicator is off, the level is 0. Short press this button to adjust dryer
temperature level from 0 to 5.
SEAT TEMPERATURE ADJUSTMENT
• Short press the “SEAT TEMP” button to adjust the seat temperature.
The indicator will show the seat temperature level if it’s on. When the indicator is off, the seat level is 0.
Short press this button to adjust seat temperature level from 0 to 5.
SEAT TEMPWATER TEMP DRYER TEMP
PULSATE
CLEAN LIGHT
H/C
CLEAN

OTHER OPERATIONS
USER CODE
• The User Code needs to be set to avoid disturbance from remote controls when more than one smart toilets
are used in the house. Turn on the toilet for setting while turning off others. Press User Code combination
buttons (Press “STOP” button first and then press “REAR” button) to enter User Code Setting Mode, the
indicator lights will be on and keep flashing.
• (RF remote control) The Remote control will generate matching User Code automatically. Press User Code
combination buttons again to exit setting mode and setting is completed. The system will retain the User
Code even if there is loss of power to the unit or the remote control.
• (IR remote control) Press water volume “+”“-” buttons to select User Code. The indicator shows the
corresponding User Code. Press the User Code combination buttons again to save settings and exit. The
buzzer beeps and it’s set successfully. If there is a loss of power to either the unit or the remote control, the
User Code will be cleared and will need to be reset. After entering setting mode, if there’s no operation for
10s, the remote control will exit setting mode automatically and return to its previous state.
QUIET MODE
•”Quiet Mode” disables the audible “beep” when pressing activation buttons.
• Long press “SEAT TEMP” button to turn on/off quiet mode.
AUTO DEODORIZATION
• While holding down the "STOP" button, depress the "FRONT/MOVE" button to start or exit the Auto
Deodorizing function. When the Auto Deodorizing function is active, it will start deodorizing automatically
when it detects a user is seated for greater than 3 seconds. The Auto Deodorizing will turn off automatically
during the drying cycle. The Auto Deodorizing function is set to "ON" by default when the unit is equipped.
APP CODE MATCHING
• Press and hold “STOP” button and then press “ ” button to start APP code matching. (This button
combination only applies to product with APP.)
IMPORTANT SOUNDS
• The unit will audibly “BEEP” when the user presses one button which means the main unit receives the
signal and conduct the operation accordingly. If the system doesn't make a “BEEP”, it means the main unit
did not receive the signal. Please adjust the Remote Control direction and retry the button selection.
• If there is a loss of power during the spray operation, the wand will not retract into it's default position. If
possible, wait until power is restored, and allow the unit to reset to it's default position. Do not manually
press in the Spray Wand as you may cause damage.
• When a user is in the seated position on the Bidet, you will hear an audible "click". This means that the
functions of Front Cleaning, Rear Cleaning, and Drying are in operation. By default, the Spray Wand will
continue to spray for 1-2 seconds if a user stands during the cleaning process. Please press the "STOP"
button if you need to stand during the cleaning process.