P/N: 01672-101 ∙ Rev. 09.19
9.0 External LED Indicator
Refer to the information below for explanation on the Receiver’s external LED indicator operation:
Green: Initial power up
Amber: Normal powered on state
Flash Green: An activated Transmitter button press has been received and processed
Flash Red: A non-activated Transmitter button press has been detected
Off: Receiver is not powered on, or failed to power up successfully
10.0 Antenna Switch
As shipped, the Receiver’s Antenna Switch is set in the INT position. Read range can be extended using a separate dipole antenna attached to
Receiver’s on-board SMA connector. If a separate antenna is used, then the switch should be set in the EXT position.
11.0 Beeper Switch
As shipped, the Receiver’s Beeper Switch is set in the ON position. If the installation technician prefers to disable the beeper and External LED
Indicator, then the Beeper Switch should be set in the OFF position.
12.0 10-Pin Terminal Block
Refer to the information below for cabling to the Receiver:
AD0: Button One, Wiegand Data 0, Channel A.
AD1: Button One, Wiegand Data 1, Channel A.
BD0: Button Two, Wiegand Data 0, Channel B.
BD1: Button Two, Wiegand Data 1, Channel B.
CD0: Button Three, Wiegand Data 0, Channel C.
CD1: Button Three, Wiegand Data 1, Channel C.
DD0: Button Four, Wiegand Data 0, Channel D.
DD1: Button Four, Wiegand Data 1, Channel D.
GND: Power, 0VDC (Ground).
+VDC: Power, 12VDC Nominal.
13.0 Connection
Connection must be done in accordance with NFPA 70. Do not connect to a receptacle controlled by a switch. Connect to a power limited DC
voltage source.
Many Speco Technologies readers carry the following certifications:
QUICK START GUIDE
AWRR44 LONG-RANGE
433-MHz RECEIVER
FCC Compliance Statement: This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved could void the user's
authority to operate the equipment.
Product can be used without license conditions or restrictions in all European Union
coun-tries, including Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Spain,
Sweden, United Kingdom, as well as other non-EU countries, including Iceland,
Norway, and Switzerland.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause unde-sired operation of the device.
Cet appareil est conforme à Industrie Canada exempts de licence standard RSS (s).
Le fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne
peut pas provoquer d’interférences et (2) ce dispositif doit accepter toute
interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
800-645-5516 • Fax: 631-957-9142 or 631-957-3880 • specotech.com
Speco Technologies reserves the right to change specifications without notice.
