Speco O4P4X2 User manual

Quick Start Guide
O4P4X2

Welcome
Thank you for purchasing this PTZ camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply or adequate PoE switch.
Please note: The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Do not expose the unit to heavy stress, violent vibration or long-term exposure to water
and humidity during transportation, storage, and/or installation.
Do not install near sources of heat.
Only install the product in environments inside the specification operating temperature
and humidity range.
Do not install the camera near power lines, radar equipment or other electromagnetic
radiation.
Do not block any ventilation openings if any.
Use all the weatherproofing hardware requirement to minimize weather intrusion.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning

Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.

Overview
3 Overview
1
Installation
2
◆ Install SD Card
Please make sure the wall is strong enough to bear the dome
camera’s weight. Please make sure the camera is powered off
during installation.
1 Ethernet connector (PoE+)
2 MIC-Audioinput (3.5mm)
3 HP-Audiooutput (3.5mm)
4 Alarminput/output
5 DC12V Power jack
6 Ground
7 Lock Screw
8 Loudspeaker
9 Light Sensor
10 Microphone
11 Reset*
12 Memory Card Slot
1
2
3
4
5
6
7
8
ALARM
4 3 2 1
9
10
11 12
*Reset: After the camera is powered on, press and hold the reset button for more than 5s to reset to
the factory default settings.

◆Install the PTZ camera
Insert a micro
SD card
1.Loosen the two screws of
the cover and then remove
the cover.
2. Insert a micro SD card as indicated
above and then install the cover back.
TF
Cover
Lock
Screw
1. Unscrew the lock screw and then
remove the adapter.
Adapter
2. Use four screws provided to
install the adapter to the ceiling.
3. Align the three screw holes of
the adapter with the screws of the
mounting base and then put these
screws into these screw holes. After
that, turn the mounting base clockwise
to secure the PTZ camera.
.
Mounting
Base
Threescrewholes
4screws(PA4x25mm)

4. Adjust the position of the PTZ camera
and then tighten the lock screw on
the side. Note that the marked
position should be the front of the
camera.
1. Unscrew the lock screw and then remove the adapter. Stick spacers on the
back of the hole B.
2. Install each part of the bracket and then mount the wall mounting
bracket to the wall with three tapping screws.
3. Attach the adapter to the brackt as shown in the following picture.
4. Tighten the lock screw on the side of the PTZ camera to secure the
camera and the adapter.
Mark
◆Install the PTZ camera with an optional wall mounting bracket
(Wall mount model WMT2)
spacer
1.
Lock
Screw
Adapter

Stick spacers on the
back of the hole B
2. Install each part of the bracket and then mount the ceiling mounting
bracket to the ceiling with three tapping screws.
3. Attach the adapter to the brackt as shown in the following picture.
4. Tighten the lock screw on the side of the PTZ camera to secure the
camera and the adapter.
◆Install the PTZ camera with an optional ceiling mounting bracket
(Ceiling Mount model CLT5)
B
PA 4x25mm
PM 4x10mm
3×
3×
1. Unscrew the lock screw and then remove the adapter. Stick spacers on the
back of the hole B.
spacer
Lock
Screw
Adapter

Cable Connection
3
Connect to
earth ground
ALARM
4321
DC12V
1--ALM-GND
2--ALM-IN
3--ALM-OPEN
4--ALM-COM
B
PA 4x25mm
3×
PM 4x10mm
3×

ConnectingAlarmInput/Output
ALARM_IN
ALARM_GND
ALARM_OPEN
ALARM_COM
ALARM
POWER
PE
Relay
The max. load of alarm output: 30VDC, 1A
Web Operation and Login
4
●Operation
IP Scanner can search for the device on the local network.
①Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
②Install IP Scanner from the CD and run it after installation.

③In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
5C :F2:0 7: 24:68 :B9
O4 P4X2
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins if prompted.