Speco ONSIP 02T5 User manual

ONSIP 02T5

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
Rev.1.0 (Nov., 2011)
Directions
Be careful not to cause any physical damage by dropping or throwing ONSIP O2T5 . Especially keep the
device out of reach from children .
Do not disassemble ONSIP O2T5 . No After Service is assumed when disassembled .
Use only the power adapter provided with ONSIP O2T5 .
Be careful to prevent moisture or water penetration into the unit . Particular attention is needed when
installing ONSIP O2T5 . The screw holes for the installation screws and pipe should be maintained water
tight during the whole life time of the product .
All the electrical connection wires running into the unit should be prepared so that water from the outside
cannot flow into the unit through the surface of the wires . Penetration of the moisture through the wire for
extended period can cause malfunction of the unit or deteriorated image .
Note
This equipment has been tested and found to comply with the limits for a Class a digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generate, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications . However, there is no guarantee that interference
will not occur in a particular installation . If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna .
 Increase the separation between the equipment and receiver .
 Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected
 Consult the dealer or an experienced radio/TV technician for help .
2

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
Revision History
Rev.1.0 (Nov., 2011)
Date
Revision
Details
2011-11-01
1.0
First manual revision creation .
Caution
Any changes or modifications to this device could void the warranty.
3

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
Contents
Contents............................................................................................................ 4
1 . Introduction................................................................................................... 6
1.1 . Overview .................................................................................................................... 6
1.2
. Specification............................................................................................................... 7
1.3. Applications of ONSIP O2T5......................................................................................
9
2 . Product Description .................................................................................... 10
2.1 . Contents................................................................................................................... 10
2.2
. Product Preview....................................................................................................... 11
2.3
. Physical description.................................................................................................. 12
2.4
. Functional Description.............................................................................................. 13
3 . On Site Installation ..................................................................................... 17
3.1 . Stand Bracket........................................................................................................... 17
4 . Getting Started............................................................................................ 18
4.1 . PC Requirement....................................................................................................... 18
4.2
. Quick Installation Guide............................................................................................ 19
5 . Trouble Shooting ........................................................................................ 25
Rev.1.0 (Nov., 2011)
4

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
5.1
. No power is applied.................................................................................................. 25
5.2
. Cannot connect to the Video.................................................................................... 26
5.3. Windows Vista or Windows 7................................................................................... 27
5.4. Technical Assistance
................................................................................................ 30
Rev.1.0 (Nov., 2011)
5

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
1. Introduction
1.1 . Overview
The ONSIP O2T5 is a state-of-the-art (Megapixel), multi-codec (H.264, MJPEG) IP camera (or network camera)
built with embedded software and hardware technology . It enables real time transmission of synchronized video
of up to 2 Megapixels and audio data . Remote clients can connect to ONSIP O2T5 for the real time video/audio
data through various client solutions running on PC, PDA or mobile phones . Real time 2-way communication is
available through bidirectional audio communication feature.
Designed to be a stand-alone streaming audio & video transmission device, ONSIP O2T5 can be applied to
various application area such as video security, remote video monitoring, distance education, video conference
or internet broadcasting system.
Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the owner to reduce TCO (Total Cost of
Ownership) by reducing on-site wiring works for the installation.
Rev.1.0 (Nov., 2011)
6

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
Details
H.264/MJPEG
**Refer to the datasheet.
32 Kbps G.726
64 Kbps PCM
RJ-45, 10/100 Mbps, PoE (802.3af)
Static, DHCP, PPP/PPPoE
RTP, RTSP, SMTP, FTP, HTTP, SDP, NTP, DNS
For providing RS-485 device
1 NC, NO Selectable
For alarm annunciation or
1
remote ON/OFF control (30V, 1A)
For factory use only
Selectable in Admin page
1 V p-p output for amplified speaker
For temporary use during installation
Power over Ethernet (IEEE802.3af)
12V DC adaptor (2A)
Stand Bracket
Arbitrary shape with independent sensitivity
Firmware upgrade over IP network
Remote administration over IP network
Simple viewing over internet explorer
Standard CMS software
Supported
Video/Audio stream encryption
ID and Password protection
IP filtering for restricting administrative
access for audio and bi-audio
Rev.1.0 (Nov., 2011)
1.2. Specification
Category
Video
Audio
(Bi-directional)
Network
I/O
Power Supply
Mounting
Motion Detection
Upgrade
Administration
Client & Viewer
Dynamic IP support
Security
Sub-Category
Compression
Resolution
Up
Down
Interface
Access network
Application
RS-485
Sensor In
Relay Output
RS-232C
Mic/Line In
Line Out
CVBS output
PoE
DC Adaptor
3 zones
Web Viewer
Speco-NVR
DDNS support
7

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
Sync to PC Synchronize to PC
Manual Manual time setting
Time management Internet Time Server Synchronize to Time Server
DLS Day Light Saving
Active-X
SDK support HTTP
Rev.1.0 (Nov., 2011)
8

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
1.3. Applications of ONSIP O2T5
 Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
Weather and environmental observation























































Rev.1.0 (Nov., 2011)
9

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
2. Product Description
2.1 . Contents
The product package contains followings:
Rev.1.0 (Nov., 2011)
Contents
Description
Remarks
ONSIP O2T5
IP camera (ONSIP O2T5 ) main unit
Power Adaptor
Default built in standard PoE module
(IEEE802.3af)
12VDC Adaptor
(Optional item)
Mounting bracket
Standard mount bracket
Supported
CD
Software & User’s Guide
Quick Reference Guide
Quick installation guide
10

CMS Software
(Speco-NVR)
PC software to view and record
the A/V streaming data transmitted
from IP camera.
(Simultaneous support of up to 64
IP cameras)
Rev.1.0 (Nov., 2011)
O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’
s
s G Gu ui id de e
2.2 . Product Preview
ONSIP O2T5
Mega pixel IP Camera
IP-Installer
PC software to allocate an IP
address to the IP Camera
11

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
2.3 . Physical description
2.3.1. External View
Figure 2-1. External view of ONSIP O2T5
2.3.2 . Rear panel
Figure 2-2. Rear panel of ONSIP O2T5
Rev.1.0 (Nov., 2011)
12

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
2.4 . Functional Description
 DC 12V: Power input for supplying 12V DC power. 

Caution: If ONSIP O2T5 is powered by PoE, do not plug in DC Jack with active DC power
into DC power connector.

MIC/LINE IN
Connect external audio source or microphone.

Line Out
Connect speakers with built in amplifier . Audio from remote site is output through Line out in bi-directional
audio mode.

100Base-T
100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). 2 LEDs on the Ethernet connector
shows the status of ONSIP O2T5 as the followings:
- Status LED (Dual Color - Red/Green) : It will be lit in green or red depending on the status.
 Green: Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is
connected to ONSIP O2T5.
 Red: Continuous or blinking red indicates that hardware is in abnormal condition.



Red/Green LED will be lit with red momentarily and it will be lit with green after a while when
power is applied into ONSIP O2T5
- LINK/LAN LED (Orange)
It will be lit with orange color when network cabling is all right. Blinking orange color indicates that
normal data transmission is under way . Off state indicates that there is trouble in network connection.
 RS-232C
3 Pins on the right of the connector are assigned for RS-232 port. Please note that leftmost pin is
numbered as 1.
Rev.1.0 (Nov., 2011)
Pin
Description
Misc .
13

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e

ALARM IN/OUT and Composite Video Output

















Figure 2-3 Terminal block for the I/O Connection of ONSIP O2T5
Used for connecting P/T device, sensor, and composite video output . Pin assignments are as follows.

RS-485
Used for connecting Pan/Tilt devices having RS-485 interface standard.
Rev.1.0 (Nov., 2011)
1
Not used
2
Not used
3
RxD (Connect to TxD of the other end)
4
TxD (RxD (Connect to RxD of the other end))
For debugging & factory use only .
5
Ground of RS-232C
Pin
Description
Misc.
1
RS-485 Plus (+)
For providing RS485 signal to RS485 devices
2
RS-485 Minus (-)
For providing RS485 signal to RS485 devices
3
SNS IN (+)
Sensor In (+):
NC/NO selectable in admin mode
4
SNS IN (1)
Sensor In (-):
NC/NO selectable in admin mode
5
RLY OUT
Relay output: Closed circuit in alarm to indicate alarm
6
RLY OUT
status
7
CVBS OUT(+)
Composite output of analog video
8
CVBS OUT(-)
Ground connection for Composite output of analog
video
14

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e

SNS IN
Examples of sensing devices are infrared sensors, motion sensors, heat/smoke sensors,
Connect the two wires of the sensors to “SNS In”. The sensor type
Administrative mode . 10mA can be flown into sensor device. Multiple
sensor devices can be connected in parallel.
Photo Coup ler
Sen so r1 +
Devic e
Sen so r1-
Senso r
Sup p ly Sup p ly
Figure 2-4. SENSOR Input connection
connecting external alarm generators such as sirens, flashing light, etc.
When
activated, relay output configures a closed circuit.
A Relay output is provided for connecting alarm devices or for remote on/off devices such as light.
Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is
capable of switching 30V AC/DC, 2A.
Relay Switch Power Supply
Out
Sup ply(30V
~)
Relay Switch
Alarm
Relay1
Supply(1~30
VDC/AC,1A )
Figure 2-5. RELAY Output connection
Rev.1.0 (Nov., 2011)
magnetic sensor,
(NC/NO) can
be set in
etc.
NO/ NCType Op e n Co llec t o rTyp e
Senso r Sensor
GND
+12V
 RLY OUT
It is used for
Po wer
Devic e
Sen so r
Po wer
Device
Power
Alarm
1V~ 30VDC/ AC,1A
Relay1
-
+
Relay
Optional
Out
Device
Power
15

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e

Factory Default Switch
A switch provided for returning the IP camera to factory default state. Press the switch for a few
seconds while power is applied.
Figure 2-6 Factory Default switch of ONSIP O2T5
Restoring the factory default will erase all settings.
Rev.1.0 (Nov., 2011)
16

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
3. On Site Installation
3.1. S St ta an nd d B Br ra ac ck ke et t
Please follow through the following procedures for the installation on the wall or ceiling.
1.
Fix the mounting bracket and bracket
holder on the wall or the ceiling using
screws.
2. Insert the bolt on the bracket into the
bracket hole and rotate the bolt
clockwise to install the IP camera on
the bracket
3 . Rotate the nut and lever clockwise to tighten.
Rev.1.0 (Nov., 2011)
17

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
4. Getting Started
Brief information for first time operation of ONSIP O2T5 is provided in this chapter.
4.1 . PC Requirement
Audio/Video streaming data received from ONSIP O2T5 can be displayed or stored in a PC running client
programs . Minimum requirement of the PC is described below:
Recommended Remark
CPU Pentium IV 3G above
Main Memory 1GB above
Operating System
*
Windows XP
Web Browser Internet Explorer 6.0 above
Graphic Card 64M above Higher than 1600x1200
Network 100 Base-T Ethernet
* Operating Systems supported: Windows 2000 Professional, Windows XP / Vista / 7
Rev.1.0 (Nov., 2011)
18

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
4.2. Quick Installation Guide
1.
Connect PC and ONSIP O2T5 to network.
1) Prepare a PC to run programs for the installation and video connection
(PC is needed to assign IP address to ONSIP O2T5)
2) In case of using PoE, connect the PC and ONSIP O2T5 to the network using one of the following ways.
If your LAN Switch does not support standard PoE, connect ONSIP O2T5 as shown in dotted line in
Figure 4-1 . The DC power is applied through DC adaptor.
DC adaptor
LAN switch
LAN switch with
standard POE
Figure 4-1 . Power and network connection
Rev.1.0 (Nov., 2011)
19

O
ON NS SI IP P O O2 2T T5 5 O Ow wn ne er r’ ’s s G Gu ui id de e
2.
Install Speco-NVR
Speco-NVR is a multi-channel CMS program for to IP camera or Video server . Install Speco-NVR on remote PC
to connect to these products. It is needed to assign connection information to Speco-NVR program before
connection.
Insert the CD provided with product into the PC and install the Speco-NVR.
Admin Page Button
IP installer
Figure 4-2. Speco-NVR
Follow the sequence below for setting the IP parameter
i) Run IP installer
ii) Click ①in IP installer window.> Double click on ②> Fill in ④> make a selection in ⑤> Fill the
parameters in ⑥
iii) Click on ⑨ to apply the settings.
iv) You can connect to admin page by clicking on ⑩.
Rev.1.0 (Nov., 2011)
20