Spectra logic T-series spectra t120 Guide

SpectraLogic.com

Spectra T120 Library

Power Supply Replacement

Instructions

2Power Supply Replacement Instructions 90950017

information contained herein are the property of Spectra Logic Corporation.

Notices Except as expressly stated herein, Spectra Logic Corporation makes its products and

associated documentation on an “AS IS” BASIS, WITHOUT WARRANTY OF ANY

KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO

THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE, BOTH OF WHICH ARE EXPRESSLY DISCLAIMED. In no

event shall Spectra Logic be liable for any loss of profits, loss of business, loss of use or

data, interruption of business, or for indirect, special, incidental or consequential

damages of any kind, even if Spectra Logic has been advised of the possibility of such

damages arising from any defect or error.

Information furnished in this manual is believed to be accurate and reliable. However, no

responsibility is assumed by Spectra Logic for its use. Due to continuing research and

development, Spectra Logic may revise this publication from time to time without notice,

and reserves the right to change any product specification at any time without notice.

Part Number 90950017 Revision A

Revision

History

Contacting

Spectra Logic

Revision Date Description

A July 2010 Initial release

General Information

Spectra Logic Web Site: www.spectralogic.com

United States Headquarters European Office

Spectra Logic Corporation

Phone: 1.800.833.1132 or 1.303.449.400

International: 1.303.449.6400

Fax: 1.303.939.8844

Spectra Logic Europe Ltd.

Phone: 44 (0) 870.112.2150

Fax: 44 (0) 870.112.2175

Spectra Logic Technical Support

Web Site: www.spectralogic.com/support

Knowledge Base:

www.spectralogic.com/knowledgebase

United States and Canada

Phone:

Toll free US and Canada: 1.800.227.4637

International: 1.303.449.0160

Email: [email protected]

Europe, Middle East, Africa

Phone: 44 (0) 870.112.2185

Email: [email protected]

Deutsch sprechende Kunden

Phone: 49 (0) 6028.9796.507

Email: [email protected]

Mexico, Central and South America, Asia, Australia, and New Zealand

Phone: 1.303.449.0160

Email: [email protected]

Library Documentation

Spectra Logic Web Site: www.spectralogic.com/documents

Power Supply Replacement

Instructions

These instructions describe how to replace a power supply in your Spectra

T120 library.

PREPARE FOR THE PROCEDURE

Ensuring ESD Protection

The repair environment for the library must be free of conditions that

could cause electrostatic discharge (ESD). To protect the library from ESD,

follow these procedures:



Place a static protection mat on the work surface used during this

procedure. Use a 1-megaohm resistor to ground the static protection mat.

Wear a static protection wrist band whenever you handle the

component when it is not in its antistatic bag. Connect this wrist band

to the static protection mat or to other suitable ESD grounding.

Keep all components in antistatic bags when not in use.

Gathering Tools and Supplies

You need the following tools and supplies to perform this procedure:

A #3 or #2 Phillips Screwdriver

Note: A #3 Phillips screwdriver is the proper

tool, but a #2 Phillips screwdriver will also work.

A Replacement 5V/12V Power Supply

Note: After removing the new power supply

from its packaging, use the packaging to return

the old power supply to Spectra Logic.

4Power Supply Replacement Instructions 90950017

Following Backup Guidelines

Stop Backups If the library is configured with a single power supply, the

library has lost power and will not power back on until the power supply

has been replaced.

Continue Backups If the library is configured with two power supplies,

the library is still operational with a single power supply functioning;

backup operations can continue while you replace the failing component.

Locating and Preparing the Malfunctioning Power Supply

One Power Supply Installed If you only have one power supply installed,

flip the power switch to the “off” position and disconnect the power cord,

then

proceed to Replace the Power Supply on page 5.

Two Power Supplies Installed If you have two power supplies installed

and AC input to both, follow these steps to determine which power supply

is malfunctioning:

1. Power the library on, then access the back of the library.

2. Check the power supply LEDs, as shown below.

3. Locate the power supply on which the DC Output (top) LED is off.

Flip the power switch to the “off” position and disconnect the power cord.

LED lights and meaning:

Solid green — the power supply is operating normally.

Off (unlit) — the power supply is malfunctioning.

AC Input

(bottom LEDs)

DC Output

(top LEDs)

T120 Library

Back View

Replace the Power Supply

July 2010 T120 Library 5

REPLACE THE POWER SUPPLY

1. Use a #3 or #2 Phillips screwdriver to loosen the screw in the upper

right corner of the power supply that you are removing.

2. Pull outward on the handle and gently remove the power supply from

the library.

3. Set the old power supply aside for return to Spectra Logic.

4. Place the new power supply into the empty slot and push it in gently.

5. Tighten the screw using a #3 or #2 Phillips screwdriver.

6. Reattach the power cord and flip the power switch to the “on” position.

7. If necessary, use your backup software to restart any backups that were

stopped when the power supply malfunctioned.

You are now ready to package the component for return to Spectra Logic.

Figure 1 The power supply screw.

Figure 2 Pulling out the power supply.

Remove screw

Power supply

handle

6Power Supply Replacement Instructions 90950017

RETURN THE COMPONENT

Return Guidelines

Unless Spectra Logic Technical Support informs you otherwise, return the

defective component to Spectra Logic following the guidelines in the

Return Procedures section below. If Spectra Logic Technical Support

informs you that the component does not need to be returned, dispose of it

in a manner appropriate for your company guidelines.

Return Procedures

After you complete the replacement procedure, return the defective

component using ALL the packaging that the replacement component

arrived in (including any anti-static bags or foam inserts).

Use the return label and instructions that were included with the

replacement component when preparing to ship the replacement part. If

you cannot locate these, contact Spectra Logic for another copy (see

Contacting Spectra Logic on page 2). The return label and RMA printed on

it are used to associate the returned part with your account. To avoid being

invoiced for failure to return the part, do not ship the part back without the

RMA return label.

Caution

Severe damage can occur if the component is not packaged correctly, and you may

be invoiced if it is received with damage due to improper or insufficient packaging.

Other manuals for T-Series Spectra T120

Table of contents

Other Spectra Logic Storage manuals

Spectra Logic

Spectra Logic Spectra 10000 User manual

Spectra Logic

Spectra Logic Spectra 64K User manual

Spectra Logic

Spectra Logic Spectra nTier500 User manual

Spectra Logic

Spectra Logic Spectra RXT150 User manual

Spectra Logic

Spectra Logic Spectra 10000 User manual

Spectra Logic

Spectra Logic Spectra 64K User manual

Spectra Logic

Spectra Logic T-Series Spectra T120 User manual

Spectra Logic

Spectra Logic Spectra 10000 Parts list manual

Spectra Logic

Spectra Logic T-Series Spectra T200 Instruction Manual

Spectra Logic

Spectra Logic Spectra 12K Instruction Manual

Spectra Logic

Spectra Logic DAStape 100 Instruction Manual

Spectra Logic

Spectra Logic Spectra nTier700 User manual

Spectra Logic

Spectra Logic Spectra 12000 Manual

Spectra Logic

Spectra Logic T-Series Spectra T50 User manual

Spectra Logic

Spectra Logic Spectra 10000 Manual

Spectra Logic

Spectra Logic T-Series Spectra T200 User manual

Spectra Logic

Spectra Logic Spectra 12K Manual

Spectra Logic

Spectra Logic Spectra 64K Manual

Spectra Logic

Spectra Logic AIT-4 Manual

Spectra Logic

Spectra Logic Spectra 10000 User manual

Spectra Logic

Spectra Logic AIT-3 Manual

Spectra Logic

Spectra Logic T-Series Spectra T50e User manual

Spectra Logic

Spectra Logic Spectra 12K Manual

Spectra Logic

Spectra Logic Spectra 10000 User manual

Popular Storage manuals by other brands

IBM

IBM 40/80 GB HH DLTVS user guide

Synology

Synology DiskStation DS716+II Quick installation guide

Vantec

Vantec NexStar-HX4 user manual

LaCie

LaCie Christofle Galet datasheet

LaCie

LaCie Rugged Thunderbolt user manual

OCZ

OCZ IBIS datasheet

Transcend

Transcend JetFlash 110 Brochure & specs

QNAP

QNAP TS 32PXU Series user guide

LaCie

LaCie RUGGED RAID user manual

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

OWC

OWC Mercury Elite Pro Dual mini Assembly manual

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

Thunderbolt

Thunderbolt 600 user manual

Intel

Intel RAID High Availability user guide

LaCie

LaCie 12big Thunderbolt 3 Quick install guide

IBM

IBM Redbooks ServeRAID-MR10M user guide

Spectra Logic T-Series Spectra T120 Guide

Popular Storage manuals by other brands