Speed Queen DR3 Instruction manual

Quick Start
Manual
DR3 Models

Welcome to the Speed Queen®family. Thank you for your support of our truly commercial quality products. Our washers and dryers are
expertly engineered to deliver commercial performance, tested to ensure ultimate durability and built with American Pride. For more than 110
years, Speed Queen consumer laundry products have been manufactured in Ripon, Wisconsin, a place where pride of workmanship is not just
alive, but thriving and embodied by each individual who designs, tests, assembles or in some way touches a Speed Queen product. A special
thing happens when that pride is combined with the highest quality commercial materials and components…it leads to the ultimate reliability…
reliability measured in decades, not years. That’s legendary Speed Queen Quality.
Three (3) Screws
(Electric Models)
Installation
Parts included:
Welcome
1.
2.
4.
3.
5.
Electric models – connect electrical cord
with three-wire or four-wire plug.
Refer to installation instructions, which can
be found at speedqueendoc.net
6.
Wipe out inside of dryer.
7.
Plug in the dryer.
Start dryer and check that dryer is heating.
Position and level the dryer.
• Recommended rear clearance
minimum is 2 in (51 mm) for utility
connections and 6 in (152 mm) when
venting through rear of unit
Connect exhaust system.
• Dryer must be exhausted to the
outdoors
• Use 4 in (102 mm) rigid duct
• Maximum straight duct length = 65 ft
(19.8 m). Each elbow deduct 10 ft (3
m)
• Sucient make-up air must be sup-
plied. The free area of any opening
for outside air must be at least 40 in2
(25806 mm2) per unit
Gas models – connect gas supply pipe.
Gas service to a gas dryer must conform
with the local codes and ordinances.
Refer to installation instructions, which can
be found at
speedqueendoc.net
• Tighten all connections securely but
do not overtighten to avoid breaking
or bending the gas valve bracket.
Turn on gas and check all pipe
connections (internal and external) for
gas leaks by applying a non-corrosive
leak detection uid to the ttings. If
bubbles are present then a leak is likely.
Retighten connections and recheck for
leaks.
Lint Filter Guard
(Optional)

6.
3.
6.
1.
4.
(gas models)
(electric models)
5.
(electric models)
2.
7.

Cycle Information
Time Dry Cycle
This cycle will operate dryer for up to 75
minutes. Cottons and heavyweight items
dry best between 50 and 75 minutes,
and lightweight items dry best between
20 and 40 minutes.
The following cycle descriptions will help determine which cycle to choose depending on the type of laundry being dried.
Sanitize*
This is a high heat, 75 minute cycle
intended to sanitize medium size loads.
Be sure to follow the item manufacturer’s
fabric care instructions.
Set the Cycle Selection to Time Dry, Max
Dry, the Fabric Selector to Perm Press/
Regular, and allow the dryer to complete
the cycle uninterrupted.
*Bacteria tested by an independent lab were Staphylococcus aureus, Pseudomonas aeruginosa, Klebsiella pneumoniae. Individual results may vary.
Automatic Regular/
Delicate Cycle
Use for sturdy items like play or work
clothes and also for delicate items.
The type of heat is determined by
choosing the proper Fabric Selector
option. There are three settings in the
Automatic Regular/Delicate cycle: Max
Dry, More Dry, and Less Dry.
Automatic Perm
Press/Knits Cycle
Use for permanent press items
and synthetics. The type of heat is
determined by selecting the proper
Fabric Selector option. There are three
settings in the Automatic Perm Press/
Knits cycle: More Dry, Less Dry, and
Cool Down (select models).

2. Clean lint lter by
wiping lint out of
screen area
(if using lint lter guard, remove
rst)
6.
Operating
1. Prepare laundry 3. Load dryer half
full with laundry
4. Close door
5. Set cycle 6. Set temperature or
fabric selector
7. Press start button
to start
8. Remove laundry
from dryer once
cycle has ended
5.
7.

Register
1. Register your product at www.speedqueen.com to take full advantage of the limited warranty.
2. Download full documentation and view installation and operating videos for an immersive experience at Speedqueendoc.net
or scan the QR code below.
3. If you wish to receive printed documents at no cost, please complete the order form online at speedqueen.com/request-printed-documents/
or email your request to [email protected].
Warranty
3, 5 & 7 Year Warranties, depending on your model.
Covers all parts and in-home labor.
Note: This unit includes a limited warranty. Refer to Speedqueendoc.net to download the full warranty bond.

Order Form for Printed Documentation ☐Please send me a printed Installation Manual, User’s Guide, and Warranty Bond. ☐I understand this card does not register my product. I must go to www.speedqueen.com to register. Model No. Serial No. Name Zip Code Phone No. Email Address Allow 1-2 weeks for delivery. Address City State

Part No. D518607
February 2021
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Speed Queen by Alliance Laundry Systems
BUSINESS REPLY MAIL
FIRST CLASS MAIL PERMIT NO. 489 RIPON,WI
POSTAGE WILL BE PAID BY ADDRESSEE
NO POSTAGE
NECESSARY IF
MAILED IN THE
UNITED STATES
SPEED QUEEN TECHNICAL DOCUMENTATION SHEPARD STREET P O BOX 990 RIPON WI 54971-9967