Spowdi Pro MKII User manual

Doc number: 003 Revision: PA9English language (original)
Solar-powered water pump
Mobile Pro MKII
Drip system manual

2
Doc number: 003 Revision: PA9
Table of Content
1 How to read this manual ............................................................................ 3
2 Drip system components ............................................................................ 4
3 Overviewofthedripsystem....................................................................... 5
4 How to install............................................................................................... 6
4.1 Waterlter......................................................................................................6
4.2 Main valve.......................................................................................................8
4.3 Main line..........................................................................................................9
4.4 Drip line.........................................................................................................11
4.4.1 Start the system...............................................................................................13

3
Doc number: 003 Revision: PA9
1 How to read this manual
The manual describes a general installation. For the system to work properly it needs
to fulll dierent requirements.
In order to better understand the requirements the Spowdi gure helps the reader:
Spowdi gure is happy when it is correct.
Spowdi gure is sad when something is NOT correct.
In the illustrations are dierent types of arrows:
Change of one state to another.
Move according to arrow.
Points out area of interest.

4
Doc number: 003 Revision: PA9
2 Drip system components
The components of drip system.
A1 A2
A3
A4
A10 A11
A5
A6 A7
A8 A9
A1. Main Line
Ø25mm, 100m
A4. Main valve. Threaded Ø25mm, 1 pc A5. Water lter, Ø25mm, 1 pc
A6. Female adapter, threaded
Ø25mm, 2 pcs
A8. Main line stopper, Ø25mm, 1 pc
A10. Multi tool, hole punch 7.5mm, 1 pc
A7. Male adapter, threaded
Ø25mm, 2 pcs
A9. Drip line stopper, Ø16mm, 20 pcs
A11. Drip holder pin, 40 pcs
A3. Drip connector,
Ø16mm, 20 pcs
A2. Drip line
Ø16mm, 500m
Spowdi Mobile Pro MKII
can irrigate 1 acre farmland.
Drip starter package is for
500sqm farmland.
Spowdi recommends 30m in
length for one growing area.
A5
A4
A2
A1
A3
A7
A6
A8
A9

5
Doc number: 003 Revision: PA9
3 Overview of the drip system
Spowdi Mobile Pro MKII
can irrigate 1 acre farmland.
Drip starter package is for
500sqm farmland.
Spowdi recommends 30m in
length for one growing area.
A5
A4
A2
A1
A3
A7
A6
A8
A9

6
Doc number: 003 Revision: PA9
4 How to install
4.1 Waterlter
1 See MK II system installation manual for
the connection of water extraction tube.
2 Remove cap on one of female adapter
(A6).
3 Take out plastic parts and O-ring as
shown in the gure.
4 Put cap, plastic parts and O-ring on
hose.
5 Screw cap anticlockwise to secure hose.
F
A5
A6
2.
3.
4.
5.
Connection of water lter to water extraction tube

7
Doc number: 003 Revision: PA9
6 Screw water lter (A5) to female adapter
(A6) and fasten it. Make sure arrow on
water lter is according to direction of
water ow.
7 Cut one length of 0,5 meter from main
line Ø25mm (A1).
8 Follow the same steps mentioned above
to mount another female adapter (A6)
on cut length of main line.
9 Screw female adapter (A6) with hose to
water lter (A5).
A5
A6
A1
0,5 meter
A6
A5
A6

8
Doc number: 003 Revision: PA9
4.2 Main valve
1 Take one male adapter (A7), remove
cap and follow the procedure same like
female adapter (A6).
2 Mount a male adapter on main line.
3 Screw male adapter (A7) to main valve
(A4) and fasten it.
A4
A7
2.
A4
3.
Connection of main valve to cut main line of water lter

9
Doc number: 003 Revision: PA9
4.3 Main line
1 Take another male adapter (A7), remove
the cap and follow the above procedure
to connect male adapter to the main line
(A1), still on roll.
2 Screw male adapter (A7) to main valve
(A4) and fasten it.
A1
A7
A4
A7
Connection of main line to main valve

10
Doc number: 003 Revision: PA9
3 Roll out main line (A1) from main valve
(A4) to the furthest END of the growing
area (after last growing bed).
Make sure not to bend the main line.
4 Cut main line at the very END of growing
area, after last growing bed.
5 Attach Ø25mm main line stopper (A8) at
end of main line. Put main line through
one of holes, bend it and then put it
back through other hole.
A8

11
Doc number: 003 Revision: PA9
6 Make holes in main line for each drip
line with Multi tool (A10).
Make holes halfway (45°) between top of
main line and side fronting growing bed.
4.4 Drip line
1 Push a drip connector (A3) into each of
new hole in main line.
45
A10
Connection of drip line to main line
A3

12
Doc number: 003 Revision: PA9
2 Roll out drip line (A2) from drip
connector (A3) to end of growing bed
and cut o drip line to same length.
Repeat for all growing beds along main
line (A1).
3 Connect a drip line to each drip
connector.
4 Attach Ø16mm stopper (A9) at end of
drip line.
Put hose through one hole, bend it and
then put it back through other hole.
A2
A9

13
Doc number: 003 Revision: PA9
5 Mount drip holder pin (A11) along drip
line in order to hold drip line in place.
4.4.1 Start the system
1 Open the valves of drip connectors.
2 Open the main valve.
A11

14
Doc number: 003 Revision: PA9
K
ON
3 Turn ON power button (K) of the PMB.
4 Operate the system for 5 minutes.
5 Check water is pouring out from dripers
on drip line.
6 Drip installation is completed.
Note!
1. Make sure there is no leakage in all connectors.
2. Check the water level in pressure vessel, if it is not on OK mark check the service
manual chapter 3.2.3.1 (Pg.7) to adjust the air regulator screw.

Spowdi AB
Registration number: 559098-2954
Augustendalsvägen 7 (11 ), 131 52
Nacka Strand, Sweden
www.spowdi.com | [email protected]