SpringAir TowerScent User manual

FAero Diffusion
Technical Specifications
TowerScent®

Table of Contents
Aero Diffusion
Technical Specifications 2023 2
I) Introduction p.3
II) Technology p.5
III) Programming p.6
IV) Towerscent Refill Duration p.9
V) Special Instructions for Use p.10
VI) Specifications p.11

Introduction
3
Aero Diffusion Technology® can be applied by 5 different devices that cover
every need. The devices have been designed in order to respond to the demands
of any project or area. They are fully programmed and ergonomical.
Aero Diffusion
Technical Specifications 2023

TowerScent®is a unique solution for
distinctive installation on the area. It can be
placed on the floor it’s fully programmed
function to respond to every need. Towerscent
can cover larger spaces with its ultra-silent
technology.
TowerScent®
4
Product Catalogue_2023

Aero Diffusion appliances of Spring Air thanks to the patented diffusion system that they use,
they can ensure the conversion of the liquid fragrance into ultra fine droplets ,distributing them
at an average of 1.000 nanometers (1 micrometer μm) in diameter.
What can be characterized as being unique concerning the Aero Diffusion Technology® is the
small droplet diameter and the extra light weight of the droplet that can ensure uniform scent
distribution.
In performance terms, Aero technology droplets convert liquid into vapor very fast. This ensures
the absence of residues on surfaces within the scented area. Very important parameter is that
the scent effect, which is created, cause very low concentration of fragrance in the air, usually
less than 1PPM which is below the international standards for allergic response.
The perfect diffusion of the fragrance into the area can be achieved with the complete
programming of the devices. Each device can be programmed for every day separately into two
different zones. Thus, given that capability, the aromatization of each space is feasible.
Technology
5
Aero Diffusion
Technical Specifications 2023

Installation
1. Insert the key to unlock the door.
2. Place the cartridge into the device.
3. Lock the door and access the power supply, then turn on the power switch, setting working
time to start.
Programming
6
Aero Diffusion
Technical Specifications 2023

1) Turn power on, the LCD displays the current hour, minutes and work day. It also shows the
current working state as WORK ON, PAUSE ON or PAUSE OFF.
Programming
7
Day & Time programming
2) Press [SET], then press [UP] or [DOWN] to adjust the hour, minute or working days setting.
3) Press [MODE] to set device’s work period and WORK/PAUSE time. For example,
A. Press [MODE] for one time, that shows to adjust ON time of first work period. Then press
[SET] [UP] [DOWN], to adjust the hour, minute and work days respectively.
B. Press [MODE] for second time that shows to adjust OFF time of first work period. Then
press [SET] [UP] [DOWN], to adjust the hour, minute and work days respectively.
C. Press [MODE] for third time to set the WORK time within 5 –300 seconds by pressing [UP] /
[DOWN]
D. Press [MODE] for fourth time to set the PAUSE time within 5 –300 seconds by pressing [UP]
/ [DOWN]
Aero Diffusion
Technical Specifications 2023

4) Please repeat the above steps to set 2nd / 3rd /4th work periods
8
5) Reset the default setting by pressing [MODE] for 10 seconds.
Default Setting:
The ON time of 1st work period is 8:00, OFF time is 22:00.
WORK time is 60 seconds, PAUSE time is 60 seconds.
The 2nd / 3rd / 4th work periods stay in blank
Aero Diffusion
Technical Specifications 2023
Programming

9
Aero Diffusion
Technical Specifications 2023
TOWER SCENT REFILL DURATION
Working Time in Sec
Stoping Time in Sec
Hours per Day
Refil Duration Days
30 120 12 60
60 120 12 30
30 120 24 30
60 120 24 15

1) This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved.
2) Children shall not play with the appliance
3) Cleaning and user maintenance shall not be made by children without supervision.
4) The appliance is not to be used by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction.
5) Unplug the appliance during filling and cleaning.
10
Aero Diffusion
Technical Specifications 2023
Special Instructions for Use

11
IconoScent®
Technical Characteristics
Reference IconoScent®Diffuser
Type Cold Evaporation Diffusion device
Diameter of particles 300nm to 1μmicron
Power Input
Input 100 -240 VAC at 0.6 A
0,14 AIN 100 V
0,074 AIN 240 V
Frequency 50/60 Hz
Protection Switching power supply
Internal Power 12 VDC at 1.5 A
Performance Up to 500 m² subject to air flow conditions
Control Programmable start & stop times
Dimensions
Height x width x depth 28cm x28cm x13cm
Weight with full container 4,800 kgs
Cartridge
Reservoir 500ml
Disposable/Recyclable
Patented Spring Air
Aero Diffusion
Technical Specifications 2023
Specifications

Revolutionary
solutions
for different
needs…