Ventev VenVolt 2 User manual

VenVolt™2802.3af/at/bt26400mAh
PowerBankUserManual
Rev. 050323ventevinfra.com \ [e-mail] \ 800-851-4965 \ ©2023 Ventev
Products Specifications:
Ports:
• USB-C (In Out)
• USB-A (Out)
• 24V Gigabit PoE (Out)
• LAN (In)
• PoE++ 802.3af/at/bt (Out)
LAN (RJ45 Gigabit)
PoE Output:
• 802.3af/at/bt 24V Gigabit PoE
USB-A Output:
• 5V/3A,9V/2A,12V/1.5A 18W (max.)
LED:
• Battery Indicator Light (100%, 75%,
50%, 25%) USB-C (Input/ Output)
USB-C Input:
• 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A
USB-C Output:
• 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A,
PPS 3.3- 21V/3A
Battery Type:
• Lithium Polymer Battery
Battery Capacity:
• 26400mAh/ 98Wh
Recharging Time:
• 3 Hours
Applications: Overview:
• The VenVolt 2 Power Bank is the perfect accessory for any WISP technician or wireless
engineer. Power your devices with USB-A, USB-C, 24V PoE, and PoE++ (802.3bt).
• Carry 26400 mAh of power with you up a tower to remotely power your devices.
• The VenVolt 2 Power Bank is temperature resistant and also features protection
from various factors such as input overvoltage, output overvoltage, short circuit,
and incorrect insertion.
User Instructions:

VenVolt™2802.3af/at/bt26400mAh
PowerBankUserManual
Rev. 050323ventevinfra.com \ [e-mail] \ 800-851-4965 \ ©2023 Ventev
User Instructions:
Operating Guide:
• Use provided USB-C wall charger and USB-C to USB-C cable to connect VenVolt 2 to
USB-C charger. Be sure to fully charge your VenVolt 2 before your first use. The battery
is shipped under 30% due to regulation requirements.USB-A (Out)
• Charging typically takes 3-4 hours to fully charge.
• Charging device PoE Device:
• To power a PoE device, use your own ethernet cable to connect from VenVolt 2
to your device.
• Move select switch from Off to 4 for PoE++ port.
• Move select switch from Off to 3 for 24V Gigabit PoE port.
• USB-C port is disabled if switch is set to 3 or 4.
• Charging laptop or phone with USB-C port:
• To power a USB device use included cable or your own cable.
• Move select switch to Off.
• Battery will automatically detect a device has been connected and charging will begin.
• Charging a device via the USB-A port:
• The USB-A port is on when select switch is set to 3 or 4. When the select switch is
set to OFF only the USB-C port is active.
Safety Precautions:
• Do not expose the product to fire or other high-temperature environments. The
recommended usage temperature is between 14-113°F.
• Do not expose the product to water.
• Stop using if any of the following conditions occur: electrolytic liquid leakage,
overheating, color change, or other unusual conditions.
• Do not short circuit the positive (+) and negative (-).
Maintenance:
• Do not expose the VenVolt 2 to direct sunlight for long periods of time or leave it any
place with high temperature
or high humidity.
• Discharge and recharge the VenVolt 2 periodically if you don’t plan to use it for an
extended period of time.
User Instructions:
FCC Part 15 Text:
• This device complies with Part
15 of the FCC Rules. Operation
is subject to the following two
conditions: (1) this device may
not cause harmful interference,
and (2) this device must accept
any interference received,
including interference that may
cause undesired operation. This
Class B device complies with
Canadian ICES-3(B)/NMB-3(B).
Note: This equipment has been
tested and found to comply
with the limits for a Class B
digital device, pursuant to part
15 of the FCC Rules. These
limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions,may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
• If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures. Reorient
or relocate the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
LED Battery Level Indicator
Troubleshooting Guide:
Problem Possible Causes Corrective Actions
The VenVolt 2 cannot be
fully charged.
1. The charging time is
not enough.
2. The power source
is defective.
1. With no devices attached,
charge the VenVolt 2 for
at least 3 hours.
2. Contact Ventev
customer service.
The remaining power in the
VenVolt 2 cannot be read.
The capacity is fully
depleted.
1. Recharge the VenVolt 2.
2. Contact Ventev
customer service
The VenVolt 2 fails to
supply power to devices.
1. The capacity is very low.
2. Poor connection
between components.
3. The VenVolt 2 may not
charge certain devices.
4. Check that the VenVolt 2
is turned on.
5. Make sure selector
switch is set to “USB-C”
for USB-C port or switch
is set to “3” or “4” for
USB-A port.
1. Recharge the VenVolt 2.
2. Reconnect or replace the
cable and/or connector.
3. Contact Ventev
customer service.
The VenVolt 2 goes into
alarm mode, all of the LED
lights are flashing.
Electrical protection has
been triggered.
1. Reconnect or replace the
cable and/or connector.
2. Press the on/off button
to reset.